From: Rishi Kumar <r-kumar12@ti.com>
To: <netdev@vger.kernel.org>
Cc: MD Danish Anwar <danishanwar@ti.com>,
Roger Quadros <rogerq@kernel.org>,
Andrew Lunn <andrew+netdev@lunn.ch>,
"David S . Miller" <davem@davemloft.net>,
Eric Dumazet <edumazet@kernel.org>,
Jakub Kicinski <kuba@kernel.org>, Paolo Abeni <pabeni@redhat.com>,
Jacob Keller <jacob.e.keller@intel.com>,
Meghana Malladi <m-malladi@ti.com>,
"Vadim Fedorenko" <vadim.fedorenko@linux.dev>,
Kevin Hao <haokexin@gmail.com>,
<linux-arm-kernel@lists.infradead.org>,
<linux-kernel@vger.kernel.org>, <j-rameshbabu@ti.com>,
<aaron.richard@ti.com>, <l-chinnannavar@ti.com>,
<m-santhoshkadavan@ti.com>, <k-tiwari1@ti.com>, <a-dev@ti.com>,
<r-kumar12@ti.com>, <pratheesh@ti.com>
Subject: [PATCH net 1/2] net: ti: icssg-prueth: fix missing port config on second interface open
Date: Wed, 14 Oct 2026 18:29:47 +0530 [thread overview]
Message-ID: <20261014125948.230571-2-r-kumar12@ti.com> (raw)
In-Reply-To: <20261014125948.230571-1-r-kumar12@ti.com>
icssg_enable_fw_offload() is gated by !prueth->emacs_initialized, so it
runs only once, on whichever port opens first. If the sibling port is
not yet running at that point, the netif_running() check skips it and
its FDB entry and VLAN table membership are never configured. If one
port is later brought down and up while the sibling stays up,
emacs_initialized is still non-zero, so the function never runs again
and the port is left unconfigured, depending on bring-up order.
Extract the per-port FDB, VLAN table, PVID and VLAN-aware setup into a
new helper icssg_enable_fw_offload_emac(), and the HSR Rx offload
setup into icssg_update_hsr_rx_offload(). Call both unconditionally
from emac_ndo_open() for the port that is actually opening, so each
port configures itself at open time regardless of sibling port state.
icssg_enable_fw_offload() now uses the same helpers and is kept for
icssg_change_mode(), which needs to reconfigure all running ports
after a full firmware restart.
prefix logs: https://gist.github.com/r-kumar12/2279fbfeb5b451a427c4c9778cdfca4a
postfix logs: https://gist.github.com/r-kumar12/071bd3625040fc1fb71207df4e652f58
Fixes: 01792bc3e5bd ("net: ti: icssg-prueth: Fix HSR and switch offload Enablement during firwmare reload.")
Signed-off-by: Rishi Kumar <r-kumar12@ti.com>
---
drivers/net/ethernet/ti/icssg/icssg_prueth.c | 72 ++++++++++++--------
1 file changed, 44 insertions(+), 28 deletions(-)
diff --git a/drivers/net/ethernet/ti/icssg/icssg_prueth.c b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
index f43c1394179f..745178fe7cf3 100644
--- a/drivers/net/ethernet/ti/icssg/icssg_prueth.c
+++ b/drivers/net/ethernet/ti/icssg/icssg_prueth.c
@@ -206,6 +206,44 @@ static void prueth_emac_stop(struct prueth *prueth)
}
}
+static void icssg_update_hsr_rx_offload(struct prueth_emac *emac)
+{
+ struct prueth *prueth = emac->prueth;
+
+ if (!prueth->is_hsr_offload_mode)
+ return;
+
+ if (emac->ndev->features & NETIF_F_HW_HSR_TAG_RM)
+ icssg_set_port_state(emac, ICSSG_EMAC_HSR_RX_OFFLOAD_ENABLE);
+ else
+ icssg_set_port_state(emac, ICSSG_EMAC_HSR_RX_OFFLOAD_DISABLE);
+}
+
+static void icssg_enable_fw_offload_emac(struct prueth_emac *emac)
+{
+ struct prueth *prueth = emac->prueth;
+
+ if (prueth->is_switch_mode || prueth->is_hsr_offload_mode) {
+ icssg_fdb_add_del(emac, eth_stp_addr, prueth->default_vlan,
+ ICSSG_FDB_ENTRY_P0_MEMBERSHIP |
+ ICSSG_FDB_ENTRY_P1_MEMBERSHIP |
+ ICSSG_FDB_ENTRY_P2_MEMBERSHIP |
+ ICSSG_FDB_ENTRY_BLOCK,
+ true);
+ icssg_vtbl_modify(emac, emac->port_vlan | DEFAULT_VID,
+ BIT(emac->port_id) | DEFAULT_PORT_MASK,
+ BIT(emac->port_id) | DEFAULT_UNTAG_MASK,
+ true);
+ if (prueth->is_hsr_offload_mode)
+ icssg_vtbl_modify(emac, DEFAULT_VID,
+ DEFAULT_PORT_MASK,
+ DEFAULT_UNTAG_MASK, true);
+ icssg_set_pvid(prueth, emac->port_vlan, emac->port_id);
+ if (prueth->is_switch_mode)
+ icssg_set_port_state(emac, ICSSG_EMAC_PORT_VLAN_AWARE_ENABLE);
+ }
+}
+
static void icssg_enable_fw_offload(struct prueth *prueth)
{
struct prueth_emac *emac;
@@ -213,34 +251,11 @@ static void icssg_enable_fw_offload(struct prueth *prueth)
for (mac = PRUETH_MAC0; mac < PRUETH_NUM_MACS; mac++) {
emac = prueth->emac[mac];
- if (prueth->is_hsr_offload_mode) {
- if (emac->ndev->features & NETIF_F_HW_HSR_TAG_RM)
- icssg_set_port_state(emac, ICSSG_EMAC_HSR_RX_OFFLOAD_ENABLE);
- else
- icssg_set_port_state(emac, ICSSG_EMAC_HSR_RX_OFFLOAD_DISABLE);
- }
- if (prueth->is_switch_mode || prueth->is_hsr_offload_mode) {
- if (netif_running(emac->ndev)) {
- icssg_fdb_add_del(emac, eth_stp_addr, prueth->default_vlan,
- ICSSG_FDB_ENTRY_P0_MEMBERSHIP |
- ICSSG_FDB_ENTRY_P1_MEMBERSHIP |
- ICSSG_FDB_ENTRY_P2_MEMBERSHIP |
- ICSSG_FDB_ENTRY_BLOCK,
- true);
- icssg_vtbl_modify(emac, emac->port_vlan | DEFAULT_VID,
- BIT(emac->port_id) | DEFAULT_PORT_MASK,
- BIT(emac->port_id) | DEFAULT_UNTAG_MASK,
- true);
- if (prueth->is_hsr_offload_mode)
- icssg_vtbl_modify(emac, DEFAULT_VID,
- DEFAULT_PORT_MASK,
- DEFAULT_UNTAG_MASK, true);
- icssg_set_pvid(prueth, emac->port_vlan, emac->port_id);
- if (prueth->is_switch_mode)
- icssg_set_port_state(emac, ICSSG_EMAC_PORT_VLAN_AWARE_ENABLE);
- }
- }
+ icssg_update_hsr_rx_offload(emac);
+
+ if (netif_running(emac->ndev))
+ icssg_enable_fw_offload_emac(emac);
}
}
@@ -1073,8 +1088,9 @@ static int emac_ndo_open(struct net_device *ndev)
ret = prueth_emac_common_start(prueth);
if (ret)
goto free_rx_irq;
- icssg_enable_fw_offload(prueth);
}
+ icssg_update_hsr_rx_offload(emac);
+ icssg_enable_fw_offload_emac(emac);
flow_cfg = emac->dram.va + ICSSG_CONFIG_OFFSET + PSI_L_REGULAR_FLOW_ID_BASE_OFFSET;
writew(emac->rx_flow_id_base, &flow_cfg->rx_base_flow);
--
2.53.0
next prev parent reply other threads:[~2026-10-14 13:00 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-10-14 12:59 [PATCH net 0/2] net: ti: icssg-prueth: fix port config and rx_mode drops Rishi Kumar
2026-10-14 12:59 ` Rishi Kumar [this message]
2026-10-14 12:59 ` [PATCH net 2/2] net: ti: icssg-prueth: re-apply rx_mode state after firmware reboot Rishi Kumar
2026-10-14 13:05 ` [PATCH net 0/2] net: ti: icssg-prueth: fix port config and rx_mode drops netdev-bot+sinfo
2026-10-14 13:38 ` KUMAR, RISHI
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=20261014125948.230571-2-r-kumar12@ti.com \
--to=r-kumar12@ti.com \
--cc=a-dev@ti.com \
--cc=aaron.richard@ti.com \
--cc=andrew+netdev@lunn.ch \
--cc=danishanwar@ti.com \
--cc=davem@davemloft.net \
--cc=edumazet@kernel.org \
--cc=haokexin@gmail.com \
--cc=j-rameshbabu@ti.com \
--cc=jacob.e.keller@intel.com \
--cc=k-tiwari1@ti.com \
--cc=kuba@kernel.org \
--cc=l-chinnannavar@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=m-malladi@ti.com \
--cc=m-santhoshkadavan@ti.com \
--cc=netdev@vger.kernel.org \
--cc=pabeni@redhat.com \
--cc=pratheesh@ti.com \
--cc=rogerq@kernel.org \
--cc=vadim.fedorenko@linux.dev \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox