From: heiko@sntech.de (Heiko Stübner)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v7 5/9] i2c: rk3x: Change SoC data to not use array
Date: Thu, 05 May 2016 23:36:49 +0200 [thread overview]
Message-ID: <2061861.OMNZ1I2HYA@diego> (raw)
In-Reply-To: <1462372418-6349-1-git-send-email-david.wu@rock-chips.com>
Am Mittwoch, 4. Mai 2016, 22:33:38 schrieb David Wu:
> Signed-off-by: David Wu <david.wu@rock-chips.com>
that makes the code look nicer (and of course prepares for you further
changes), so
Reviewed-by: Heiko Stuebner <heiko@sntech.de>
> ---
> drivers/i2c/busses/i2c-rk3x.c | 38 ++++++++++++++++++++++++++++++--------
> 1 file changed, 30 insertions(+), 8 deletions(-)
>
> diff --git a/drivers/i2c/busses/i2c-rk3x.c b/drivers/i2c/busses/i2c-rk3x.c
> index 0838fcf..9686c81 100644
> --- a/drivers/i2c/busses/i2c-rk3x.c
> +++ b/drivers/i2c/busses/i2c-rk3x.c
> @@ -867,17 +867,39 @@ static const struct i2c_algorithm rk3x_i2c_algorithm =
> { .functionality = rk3x_i2c_func,
> };
>
> -static struct rk3x_i2c_soc_data soc_data[3] = {
> - { .grf_offset = 0x154 }, /* rk3066 */
> - { .grf_offset = 0x0a4 }, /* rk3188 */
> - { .grf_offset = -1 }, /* no I2C switching needed */
> +static const struct rk3x_i2c_soc_data rk3066_soc_data = {
> + .grf_offset = 0x154,
> +};
> +
> +static const struct rk3x_i2c_soc_data rk3188_soc_data = {
> + .grf_offset = 0x0a4,
> +};
> +
> +static const struct rk3x_i2c_soc_data rk3228_soc_data = {
> + .grf_offset = -1,
> +};
> +
> +static const struct rk3x_i2c_soc_data rk3288_soc_data = {
> + .grf_offset = -1,
> };
>
> static const struct of_device_id rk3x_i2c_match[] = {
> - { .compatible = "rockchip,rk3066-i2c", .data = (void *)&soc_data[0] },
> - { .compatible = "rockchip,rk3188-i2c", .data = (void *)&soc_data[1] },
> - { .compatible = "rockchip,rk3228-i2c", .data = (void *)&soc_data[2] },
> - { .compatible = "rockchip,rk3288-i2c", .data = (void *)&soc_data[2] },
> + {
> + .compatible = "rockchip,rk3066-i2c",
> + .data = (void *)&rk3066_soc_data
> + },
> + {
> + .compatible = "rockchip,rk3188-i2c",
> + .data = (void *)&rk3188_soc_data
> + },
> + {
> + .compatible = "rockchip,rk3228-i2c",
> + .data = (void *)&rk3228_soc_data
> + },
> + {
> + .compatible = "rockchip,rk3288-i2c",
> + .data = (void *)&rk3288_soc_data
> + },
> {},
> };
> MODULE_DEVICE_TABLE(of, rk3x_i2c_match);
next prev parent reply other threads:[~2016-05-05 21:36 UTC|newest]
Thread overview: 29+ messages / expand[flat|nested] mbox.gz Atom feed top
2016-05-04 14:13 [PATCH v7 0/9] add i2c driver supported for rk3399 David Wu
2016-05-04 14:13 ` [PATCH v7 1/9] i2c: rk3x: add documentation to fields in "struct rk3x_i2c" David Wu
2016-05-04 23:45 ` Doug Anderson
2016-05-04 23:50 ` Doug Anderson
2016-05-04 14:13 ` [PATCH v7 2/9] i2c: rk3x: use struct "rk3x_i2c_calced_timings" David Wu
2016-05-05 22:55 ` Doug Anderson
2016-05-06 2:19 ` David.Wu
2016-05-04 14:13 ` [PATCH v7 3/9] i2c: rk3x: Remove redundant rk3x_i2c_clean_ipd() David Wu
2016-05-05 22:55 ` Doug Anderson
2016-05-04 14:13 ` [PATCH v7 4/9] i2c: rk3x: Move setting STATE_START and add STATE_SETUP David Wu
2016-05-05 22:56 ` Doug Anderson
2016-05-06 3:20 ` David.Wu
2016-05-04 14:33 ` [PATCH v7 5/9] i2c: rk3x: Change SoC data to not use array David Wu
2016-05-05 21:36 ` Heiko Stübner [this message]
2016-05-05 22:57 ` Doug Anderson
2016-05-04 14:34 ` [PATCH v7 6/9] i2c: rk3x: Move spec timing data to "static const" structs David Wu
2016-05-05 22:58 ` Doug Anderson
2016-05-06 4:55 ` David.Wu
2016-05-04 14:35 ` [PATCH v7 7/9] dt-bindings: i2c: rk3x: add support for rk3399 David Wu
2016-05-05 22:12 ` Rob Herring
2016-05-06 6:09 ` David.Wu
2016-05-05 22:59 ` Doug Anderson
2016-05-04 14:36 ` [PATCH v7 8/9] i2c: rk3x: add i2c support for rk3399 soc David Wu
2016-05-05 23:00 ` Doug Anderson
2016-05-06 9:32 ` David.Wu
2016-05-06 18:00 ` Doug Anderson
2016-05-04 14:37 ` [PATCH v7 9/9] i2c: rk3x: support fast-mode plus for rk3399 David Wu
2016-05-05 23:02 ` Doug Anderson
2016-05-06 2:12 ` David.Wu
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=2061861.OMNZ1I2HYA@diego \
--to=heiko@sntech.de \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).