* [PATCH v5 0/8] Build and support rk3036 SoC platform @ 2015-10-26 4:25 Xing Zheng 2015-10-26 4:25 ` [PATCH v5 1/8] dt-bindings: add documentation of rk3036 clock controller Xing Zheng ` (6 more replies) 0 siblings, 7 replies; 9+ messages in thread From: Xing Zheng @ 2015-10-26 4:25 UTC (permalink / raw) To: linux-arm-kernel Hi, We need to support rk3036 soc platform via upstream, there are 3 primary parts for the initial release of minimum system: dts, pinctrl, and clock tree for rk3036, and additional, we can use these startup and run to init processs. Thanks. Changed in v5: - don't use clk_ APIs in the pll init-callback Changed in v4: - add some basic IP modules on rk3036.dtsi - optimized supporting smp codes Changed in v3: - optimized some codes based on v2 - removed the patch "initial set time for rtc-hym8563" (useless) - removed the patch "pinctrl" (approved) Changed in v2: - based on v1, add clock controller documentation - enable timer5 startup - add smp for cpu1 - initial set time for rtc-hym8563 Changes in v1: - add dts, pinctrl and clock tree for rk3036 soc platform The patchset (8): 8) rockchip: make sure timer5 is enabled on rk3036 platforms 7) ARM: dts: enable smp for rk3036 6) ARM: rockchip: add support smp for rk3036 5) ARM: dts: rockchip: add core rk3036 dts 4) clk: rockchip: add new pll-type for rk3036 and similar socs 3) clk: rockchip: add clock controller for rk3036 2) clk: rockchip: add dt-binding header for rk3036 1) dt-bindings: add documentation of rk3036 clock controller Changes in v5: Signed-off-by: Xing Zheng <zhengxing@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> Heiko Stuebner (1): ARM: rockchip: add support smp for rk3036 Xing Zheng (7): dt-bindings: add documentation of rk3036 clock controller clk: rockchip: add dt-binding header for rk3036 clk: rockchip: add clock controller for rk3036 clk: rockchip: add new pll-type for rk3036 and similar socs ARM: dts: rockchip: add core rk3036 dts ARM: dts: enable smp for rk3036 rockchip: make sure timer5 is enabled on rk3036 platforms Documentation/devicetree/bindings/arm/cpus.txt | 1 + .../bindings/clock/rockchip,rk3036-cru.txt | 56 ++ arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/rk3036-evb.dts | 64 +++ arch/arm/boot/dts/rk3036.dtsi | 541 ++++++++++++++++++++ arch/arm/mach-rockchip/platsmp.c | 45 +- arch/arm/mach-rockchip/rockchip.c | 44 +- drivers/clk/rockchip/Makefile | 1 + drivers/clk/rockchip/clk-pll.c | 249 ++++++++- drivers/clk/rockchip/clk-rk3036.c | 500 ++++++++++++++++++ drivers/clk/rockchip/clk.h | 30 ++ include/dt-bindings/clock/rk3036-cru.h | 195 +++++++ 12 files changed, 1697 insertions(+), 30 deletions(-) create mode 100644 Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt create mode 100644 arch/arm/boot/dts/rk3036-evb.dts create mode 100644 arch/arm/boot/dts/rk3036.dtsi create mode 100644 drivers/clk/rockchip/clk-rk3036.c create mode 100644 include/dt-bindings/clock/rk3036-cru.h -- 1.7.9.5 ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH v5 1/8] dt-bindings: add documentation of rk3036 clock controller 2015-10-26 4:25 [PATCH v5 0/8] Build and support rk3036 SoC platform Xing Zheng @ 2015-10-26 4:25 ` Xing Zheng 2015-10-26 4:25 ` [PATCH v5 3/8] clk: rockchip: add clock controller for rk3036 Xing Zheng ` (5 subsequent siblings) 6 siblings, 0 replies; 9+ messages in thread From: Xing Zheng @ 2015-10-26 4:25 UTC (permalink / raw) To: linux-arm-kernel Add the devicetree binding for the cru on the rk3036 which quite similar structured as previous clock controllers. Signed-off-by: Xing Zheng <zhengxing@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> --- Changes in v5: None .../bindings/clock/rockchip,rk3036-cru.txt | 56 ++++++++++++++++++++ 1 file changed, 56 insertions(+) create mode 100644 Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt diff --git a/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt b/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt new file mode 100644 index 0000000..ace0599 --- /dev/null +++ b/Documentation/devicetree/bindings/clock/rockchip,rk3036-cru.txt @@ -0,0 +1,56 @@ +* Rockchip RK3036 Clock and Reset Unit + +The RK3036 clock controller generates and supplies clock to various +controllers within the SoC and also implements a reset controller for SoC +peripherals. + +Required Properties: + +- compatible: should be "rockchip,rk3036-cru" +- reg: physical base address of the controller and length of memory mapped + region. +- #clock-cells: should be 1. +- #reset-cells: should be 1. + +Optional Properties: + +- rockchip,grf: phandle to the syscon managing the "general register files" + If missing pll rates are not changeable, due to the missing pll lock status. + +Each clock is assigned an identifier and client nodes can use this identifier +to specify the clock which they consume. All available clocks are defined as +preprocessor macros in the dt-bindings/clock/rk3036-cru.h headers and can be +used in device tree sources. Similar macros exist for the reset sources in +these files. + +External clocks: + +There are several clocks that are generated outside the SoC. It is expected +that they are defined using standard clock bindings with following +clock-output-names: + - "xin24m" - crystal input - required, + - "ext_i2s" - external I2S clock - optional, + - "ext_gmac" - external GMAC clock - optional + +Example: Clock controller node: + + cru: cru at 20000000 { + compatible = "rockchip,rk3036-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + + #clock-cells = <1>; + #reset-cells = <1>; + }; + +Example: UART controller node that consumes the clock generated by the clock + controller: + + uart0: serial at 20060000 { + compatible = "snps,dw-apb-uart"; + reg = <0x20060000 0x100>; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&cru SCLK_UART0>; + }; -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v5 3/8] clk: rockchip: add clock controller for rk3036 2015-10-26 4:25 [PATCH v5 0/8] Build and support rk3036 SoC platform Xing Zheng 2015-10-26 4:25 ` [PATCH v5 1/8] dt-bindings: add documentation of rk3036 clock controller Xing Zheng @ 2015-10-26 4:25 ` Xing Zheng 2015-10-28 7:53 ` Heiko Stuebner 2015-10-26 4:25 ` [PATCH v5 4/8] clk: rockchip: add new pll-type for rk3036 and similar socs Xing Zheng ` (4 subsequent siblings) 6 siblings, 1 reply; 9+ messages in thread From: Xing Zheng @ 2015-10-26 4:25 UTC (permalink / raw) To: linux-arm-kernel Add the clock tree definition for the new rk3036 SoC. Signed-off-by: Xing Zheng <zhengxing@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> --- Changes in v5: None drivers/clk/rockchip/Makefile | 1 + drivers/clk/rockchip/clk-rk3036.c | 500 +++++++++++++++++++++++++++++++++++++ drivers/clk/rockchip/clk.h | 30 +++ 3 files changed, 531 insertions(+) create mode 100644 drivers/clk/rockchip/clk-rk3036.c diff --git a/drivers/clk/rockchip/Makefile b/drivers/clk/rockchip/Makefile index b27edd6..d599829 100644 --- a/drivers/clk/rockchip/Makefile +++ b/drivers/clk/rockchip/Makefile @@ -10,6 +10,7 @@ obj-y += clk-inverter.o obj-y += clk-mmc-phase.o obj-$(CONFIG_RESET_CONTROLLER) += softrst.o +obj-y += clk-rk3036.o obj-y += clk-rk3188.o obj-y += clk-rk3288.o obj-y += clk-rk3368.o diff --git a/drivers/clk/rockchip/clk-rk3036.c b/drivers/clk/rockchip/clk-rk3036.c new file mode 100644 index 0000000..6f49df3 --- /dev/null +++ b/drivers/clk/rockchip/clk-rk3036.c @@ -0,0 +1,500 @@ +/* + * Copyright (c) 2014 MundoReader S.L. + * Author: Heiko Stuebner <heiko@sntech.de> + * + * Copyright (c) 2015 Rockchip Electronics Co. Ltd. + * Author: Xing Zheng <zhengxing@rock-chips.com> + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + */ + +#include <linux/clk-provider.h> +#include <linux/of.h> +#include <linux/of_address.h> +#include <linux/syscore_ops.h> +#include <dt-bindings/clock/rk3036-cru.h> +#include "clk.h" + +#define RK3036_GRF_SOC_STATUS0 0x14c + +enum rk3036_plls { + apll, dpll, gpll, +}; + +static struct rockchip_pll_rate_table rk3036_pll_rates[] = { + /* _mhz, _refdiv, _fbdiv, _postdiv1, _postdiv2, _dsmpd, _frac */ + RK3036_PLL_RATE(1608000000, 1, 67, 1, 1, 1, 0), + RK3036_PLL_RATE(1584000000, 1, 66, 1, 1, 1, 0), + RK3036_PLL_RATE(1560000000, 1, 65, 1, 1, 1, 0), + RK3036_PLL_RATE(1536000000, 1, 64, 1, 1, 1, 0), + RK3036_PLL_RATE(1512000000, 1, 63, 1, 1, 1, 0), + RK3036_PLL_RATE(1488000000, 1, 62, 1, 1, 1, 0), + RK3036_PLL_RATE(1464000000, 1, 61, 1, 1, 1, 0), + RK3036_PLL_RATE(1440000000, 1, 60, 1, 1, 1, 0), + RK3036_PLL_RATE(1416000000, 1, 59, 1, 1, 1, 0), + RK3036_PLL_RATE(1392000000, 1, 58, 1, 1, 1, 0), + RK3036_PLL_RATE(1368000000, 1, 57, 1, 1, 1, 0), + RK3036_PLL_RATE(1344000000, 1, 56, 1, 1, 1, 0), + RK3036_PLL_RATE(1320000000, 1, 55, 1, 1, 1, 0), + RK3036_PLL_RATE(1296000000, 1, 54, 1, 1, 1, 0), + RK3036_PLL_RATE(1272000000, 1, 53, 1, 1, 1, 0), + RK3036_PLL_RATE(1248000000, 1, 52, 1, 1, 1, 0), + RK3036_PLL_RATE(1200000000, 1, 50, 1, 1, 1, 0), + RK3036_PLL_RATE(1188000000, 2, 99, 1, 1, 1, 0), + RK3036_PLL_RATE(1104000000, 1, 46, 1, 1, 1, 0), + RK3036_PLL_RATE(1100000000, 12, 550, 1, 1, 1, 0), + RK3036_PLL_RATE(1008000000, 1, 84, 2, 1, 1, 0), + RK3036_PLL_RATE(1000000000, 6, 500, 2, 1, 1, 0), + RK3036_PLL_RATE( 984000000, 1, 82, 2, 1, 1, 0), + RK3036_PLL_RATE( 960000000, 1, 80, 2, 1, 1, 0), + RK3036_PLL_RATE( 936000000, 1, 78, 2, 1, 1, 0), + RK3036_PLL_RATE( 912000000, 1, 76, 2, 1, 1, 0), + RK3036_PLL_RATE( 900000000, 4, 300, 2, 1, 1, 0), + RK3036_PLL_RATE( 888000000, 1, 74, 2, 1, 1, 0), + RK3036_PLL_RATE( 864000000, 1, 72, 2, 1, 1, 0), + RK3036_PLL_RATE( 840000000, 1, 70, 2, 1, 1, 0), + RK3036_PLL_RATE( 816000000, 1, 68, 2, 1, 1, 0), + RK3036_PLL_RATE( 800000000, 6, 400, 2, 1, 1, 0), + RK3036_PLL_RATE( 700000000, 6, 350, 2, 1, 1, 0), + RK3036_PLL_RATE( 696000000, 1, 58, 2, 1, 1, 0), + RK3036_PLL_RATE( 600000000, 1, 75, 3, 1, 1, 0), + RK3036_PLL_RATE( 594000000, 2, 99, 2, 1, 1, 0), + RK3036_PLL_RATE( 504000000, 1, 63, 3, 1, 1, 0), + RK3036_PLL_RATE( 500000000, 6, 250, 2, 1, 1, 0), + RK3036_PLL_RATE( 408000000, 1, 68, 2, 2, 1, 0), + RK3036_PLL_RATE( 312000000, 1, 52, 2, 2, 1, 0), + RK3036_PLL_RATE( 216000000, 1, 72, 4, 2, 1, 0), + RK3036_PLL_RATE( 96000000, 1, 64, 4, 4, 1, 0), + { /* sentinel */ }, +}; + +#define RK3036_DIV_CPU_MASK 0x1f +#define RK3036_DIV_CPU_SHIFT 8 + +#define RK3036_DIV_PERI_MASK 0xf +#define RK3036_DIV_PERI_SHIFT 0 +#define RK3036_DIV_ACLK_MASK 0x7 +#define RK3036_DIV_ACLK_SHIFT 4 +#define RK3036_DIV_HCLK_MASK 0x3 +#define RK3036_DIV_HCLK_SHIFT 8 +#define RK3036_DIV_PCLK_MASK 0x7 +#define RK3036_DIV_PCLK_SHIFT 12 + +#define RK3036_CLKSEL1(_core_periph_div) \ + { \ + .reg = RK2928_CLKSEL_CON(1), \ + .val = HIWORD_UPDATE(_core_periph_div, RK3036_DIV_PERI_MASK, \ + RK3036_DIV_PERI_SHIFT) \ + } + +#define RK3036_CPUCLK_RATE(_prate, _core_periph_div) \ + { \ + .prate = _prate, \ + .divs = { \ + RK3036_CLKSEL1(_core_periph_div), \ + }, \ + } + +static struct rockchip_cpuclk_rate_table rk3036_cpuclk_rates[] __initdata = { + RK3036_CPUCLK_RATE(816000000, 4), + RK3036_CPUCLK_RATE(600000000, 4), + RK3036_CPUCLK_RATE(312000000, 4), +}; + +static const struct rockchip_cpuclk_reg_data rk3036_cpuclk_data = { + .core_reg = RK2928_CLKSEL_CON(0), + .div_core_shift = 0, + .div_core_mask = 0x1f, + .mux_core_shift = 7, +}; + +PNAME(mux_pll_p) = { "xin24m", "xin24m" }; + +PNAME(mux_armclk_p) = { "apll", "gpll_armclk" }; +PNAME(mux_busclk_p) = { "apll", "dpll_cpu", "gpll_cpu" }; +PNAME(mux_ddrphy_p) = { "dpll_ddr", "gpll_ddr" }; +PNAME(mux_pll_src_3plls_p) = { "apll", "dpll", "gpll" }; +PNAME(mux_timer_p) = { "xin24m", "pclk_peri_src" }; + +PNAME(mux_pll_src_apll_dpll_gpll_usb480m_p) = { "apll", "dpll", "gpll" "usb480m" }; + +PNAME(mux_mmc_src_p) = { "apll", "dpll", "gpll", "xin24m" }; +PNAME(mux_i2s_pre_p) = { "i2s_src", "i2s_frac", "ext_i2s", "xin12m" }; +PNAME(mux_i2s_clkout_p) = { "i2s_pre", "xin12m" }; +PNAME(mux_spdif_p) = { "spdif_src", "spdif_frac", "xin12m" }; +PNAME(mux_uart0_p) = { "uart0_src", "uart0_frac", "xin24m" }; +PNAME(mux_uart1_p) = { "uart1_src", "uart1_frac", "xin24m" }; +PNAME(mux_uart2_p) = { "uart2_src", "uart2_frac", "xin24m" }; +PNAME(mux_mac_p) = { "mac_pll_src", "ext_gmac" }; +PNAME(mux_dclk_p) = { "dclk_lcdc", "dclk_hdmi_src" }; + +static struct rockchip_pll_clock rk3036_pll_clks[] __initdata = { + [apll] = PLL(pll_rk3036, PLL_APLL, "apll", mux_pll_p, 0, RK2928_PLL_CON(0), + RK2928_MODE_CON, 0, 5, 0, rk3036_pll_rates), + [dpll] = PLL(pll_rk3036, PLL_DPLL, "dpll", mux_pll_p, 0, RK2928_PLL_CON(4), + RK2928_MODE_CON, 4, 4, 0, NULL), + [gpll] = PLL(pll_rk3036, PLL_GPLL, "gpll", mux_pll_p, 0, RK2928_PLL_CON(12), + RK2928_MODE_CON, 12, 6, ROCKCHIP_PLL_SYNC_RATE, rk3036_pll_rates), +}; + +#define MFLAGS CLK_MUX_HIWORD_MASK +#define DFLAGS CLK_DIVIDER_HIWORD_MASK +#define GFLAGS (CLK_GATE_HIWORD_MASK | CLK_GATE_SET_TO_DISABLE) + +static struct rockchip_clk_branch rk3036_clk_branches[] __initdata = { + /* + * Clock-Architecture Diagram 1 + */ + + /* PD_CORE */ + GATE(0, "gpll_armclk", "gpll", CLK_IGNORE_UNUSED, + RK2928_CLKGATE_CON(0), 6, GFLAGS), + + /* + * Clock-Architecture Diagram 2 + */ + + /* PD_DDR */ + GATE(0, "dpll_ddr", "dpll", CLK_IGNORE_UNUSED, + RK2928_CLKGATE_CON(0), 2, GFLAGS), + GATE(0, "gpll_ddr", "gpll", CLK_IGNORE_UNUSED, + RK2928_CLKGATE_CON(0), 8, GFLAGS), + COMPOSITE_NOGATE(0, "ddrphy2x", mux_ddrphy_p, CLK_IGNORE_UNUSED, + RK2928_CLKSEL_CON(26), 8, 1, MFLAGS, 0, 2, DFLAGS | CLK_DIVIDER_POWER_OF_TWO), + + /* PD_CORE */ + COMPOSITE_NOMUX(0, "pclk_dbg", "armclk", CLK_IGNORE_UNUSED, + RK2928_CLKSEL_CON(1), 0, 4, DFLAGS | CLK_DIVIDER_READ_ONLY, + RK2928_CLKGATE_CON(0), 7, GFLAGS), + COMPOSITE_NOMUX(0, "aclk_core_pre", "armclk", CLK_IGNORE_UNUSED, + RK2928_CLKSEL_CON(1), 4, 3, DFLAGS | CLK_DIVIDER_READ_ONLY, + RK2928_CLKGATE_CON(0), 7, GFLAGS), + + /* PD_CPU (BUS) */ + GATE(0, "dpll_cpu", "dpll", 0, RK2928_CLKGATE_CON(10), 8, GFLAGS), + GATE(0, "gpll_cpu", "gpll", 0, RK2928_CLKGATE_CON(0), 1, GFLAGS), + COMPOSITE_NOGATE(0, "aclk_cpu_src", mux_busclk_p, 0, + RK2928_CLKSEL_CON(0), 14, 2, MFLAGS, 8, 5, DFLAGS), + GATE(ACLK_CPU, "aclk_cpu", "aclk_cpu_src", CLK_IGNORE_UNUSED, + RK2928_CLKGATE_CON(0), 3, GFLAGS), + COMPOSITE_NOMUX(PCLK_CPU, "pclk_cpu", "aclk_cpu_src", CLK_IGNORE_UNUSED, + RK2928_CLKSEL_CON(1), 12, 3, DFLAGS | CLK_DIVIDER_READ_ONLY, + RK2928_CLKGATE_CON(0), 5, GFLAGS), + COMPOSITE_NOMUX(HCLK_CPU, "hclk_cpu", "aclk_cpu_src", CLK_IGNORE_UNUSED, + RK2928_CLKSEL_CON(1), 8, 2, DFLAGS | CLK_DIVIDER_READ_ONLY, + RK2928_CLKGATE_CON(0), 4, GFLAGS), + + /* PD_PERI */ + COMPOSITE(0, "aclk_peri_src", mux_pll_src_3plls_p, 0, + RK2928_CLKSEL_CON(10), 14, 2, MFLAGS, 0, 5, DFLAGS, + RK2928_CLKGATE_CON(2), 0, GFLAGS), + + GATE(ACLK_PERI, "aclk_peri", "aclk_peri_src", 0, + RK2928_CLKGATE_CON(2), 1, GFLAGS), + /* pclk_peri_src is soure for timers */ + DIV(0, "pclk_peri_src", "aclk_peri_src", CLK_IGNORE_UNUSED, + RK2928_CLKSEL_CON(10), 12, 2, DFLAGS | CLK_DIVIDER_POWER_OF_TWO), + GATE(PCLK_PERI, "pclk_peri", "pclk_peri_src", 0, + RK2928_CLKGATE_CON(2), 3, GFLAGS), + /* hclk_peri_src is soure for sclk_macref_out */ + DIV(0, "hclk_peri_src", "aclk_peri_src", CLK_IGNORE_UNUSED, + RK2928_CLKSEL_CON(10), 8, 2, DFLAGS | CLK_DIVIDER_POWER_OF_TWO), + GATE(HCLK_PERI, "hclk_peri", "hclk_peri_src", 0, + RK2928_CLKGATE_CON(2), 2, GFLAGS), + + /* PD_TIMER */ + COMPOSITE_NODIV(SCLK_TIMER0, "sclk_timer0", mux_timer_p, CLK_IGNORE_UNUSED, + RK2928_CLKSEL_CON(2), 4, 1, DFLAGS, + RK2928_CLKGATE_CON(1), 0, GFLAGS), + COMPOSITE_NODIV(SCLK_TIMER1, "sclk_timer1", mux_timer_p, CLK_IGNORE_UNUSED, + RK2928_CLKSEL_CON(2), 5, 1, DFLAGS, + RK2928_CLKGATE_CON(1), 1, GFLAGS), + COMPOSITE_NODIV(SCLK_TIMER2, "sclk_timer2", mux_timer_p, CLK_IGNORE_UNUSED, + RK2928_CLKSEL_CON(2), 6, 1, DFLAGS, + RK2928_CLKGATE_CON(2), 4, GFLAGS), + COMPOSITE_NODIV(SCLK_TIMER3, "sclk_timer3", mux_timer_p, CLK_IGNORE_UNUSED, + RK2928_CLKSEL_CON(2), 7, 1, DFLAGS, + RK2928_CLKGATE_CON(2), 5, GFLAGS), + + /* PD_UART */ + MUX(0, "uart_pll_clk", mux_pll_src_apll_dpll_gpll_usb480m_p, 0, + RK2928_CLKSEL_CON(13), 10, 2, MFLAGS), + COMPOSITE_NOMUX(0, "uart0_src", "uart_pll_clk", 0, + RK2928_CLKSEL_CON(13), 0, 7, DFLAGS, + RK2928_CLKGATE_CON(1), 8, GFLAGS), + COMPOSITE_NOMUX(0, "uart1_src", "uart_pll_clk", 0, + RK2928_CLKSEL_CON(13), 0, 7, DFLAGS, + RK2928_CLKGATE_CON(1), 8, GFLAGS), + COMPOSITE_NOMUX(0, "uart2_src", "uart_pll_clk", 0, + RK2928_CLKSEL_CON(13), 0, 7, DFLAGS, + RK2928_CLKGATE_CON(1), 8, GFLAGS), + COMPOSITE_FRAC(0, "uart0_frac", "uart0_src", CLK_SET_RATE_PARENT, + RK2928_CLKSEL_CON(17), 0, + RK2928_CLKGATE_CON(1), 9, GFLAGS), + COMPOSITE_FRAC(0, "uart1_frac", "uart1_src", CLK_SET_RATE_PARENT, + RK2928_CLKSEL_CON(18), 0, + RK2928_CLKGATE_CON(1), 11, GFLAGS), + COMPOSITE_FRAC(0, "uart2_frac", "uart2_src", CLK_SET_RATE_PARENT, + RK2928_CLKSEL_CON(19), 0, + RK2928_CLKGATE_CON(1), 13, GFLAGS), + MUX(SCLK_UART0, "sclk_uart0", mux_uart0_p, CLK_SET_RATE_PARENT, + RK2928_CLKSEL_CON(13), 8, 2, MFLAGS), + MUX(SCLK_UART1, "sclk_uart1", mux_uart1_p, CLK_SET_RATE_PARENT, + RK2928_CLKSEL_CON(14), 8, 2, MFLAGS), + MUX(SCLK_UART2, "sclk_uart2", mux_uart2_p, CLK_SET_RATE_PARENT, + RK2928_CLKSEL_CON(15), 8, 2, MFLAGS), + + /* PD_VIDEO */ + COMPOSITE(0, "aclk_vcodec", mux_pll_src_3plls_p, 0, + RK2928_CLKSEL_CON(32), 14, 2, MFLAGS, 8, 5, DFLAGS, + RK2928_CLKGATE_CON(3), 11, GFLAGS), + + COMPOSITE(0, "aclk_hvec", mux_pll_src_3plls_p, 0, + RK2928_CLKSEL_CON(20), 0, 2, MFLAGS, 2, 5, DFLAGS, + RK2928_CLKGATE_CON(10), 6, GFLAGS), + + /* PD_VIO */ + COMPOSITE(0, "aclk_disp1_pre", mux_pll_src_3plls_p, 0, + RK2928_CLKSEL_CON(31), 14, 2, MFLAGS, 8, 5, DFLAGS, + RK2928_CLKGATE_CON(1), 4, GFLAGS), + COMPOSITE(0, "hclk_disp_pre", mux_pll_src_3plls_p, 0, + RK2928_CLKSEL_CON(30), 14, 2, MFLAGS, 8, 5, DFLAGS, + RK2928_CLKGATE_CON(0), 11, GFLAGS), + COMPOSITE(DCLK_LCDC, "dclk_lcdc", mux_pll_src_3plls_p, 0, + RK2928_CLKSEL_CON(28), 0, 2, MFLAGS, 8, 8, DFLAGS, + RK2928_CLKGATE_CON(3), 2, GFLAGS), + + /* MMC */ + COMPOSITE_NODIV(0, "sclk_sdmmc_src", mux_mmc_src_p, 0, + RK2928_CLKSEL_CON(12), 8, 2, DFLAGS, + RK2928_CLKGATE_CON(2), 11, GFLAGS), + DIV(SCLK_SDMMC, "sclk_sdmmc", "sclk_sdmmc_src", 0, + RK2928_CLKSEL_CON(11), 0, 7, DFLAGS), + + COMPOSITE_NODIV(0, "sclk_sdio_src", mux_mmc_src_p, 0, + RK2928_CLKSEL_CON(12), 10, 2, DFLAGS, + RK2928_CLKGATE_CON(2), 13, GFLAGS), + DIV(SCLK_SDIO, "sclk_sdio", "sclk_sdio_src", 0, + RK2928_CLKSEL_CON(11), 8, 7, DFLAGS), + + COMPOSITE(SCLK_EMMC, "sclk_emmc", mux_mmc_src_p, 0, + RK2928_CLKSEL_CON(12), 12, 2, MFLAGS, 0, 7, DFLAGS, + RK2928_CLKGATE_CON(2), 14, GFLAGS), + + MMC(SCLK_SDMMC_DRV, "sdmmc_drv", "sclk_sdmmc", RK3036_SDMMC_CON0, 1), + MMC(SCLK_SDMMC_SAMPLE, "sdmmc_sample", "sclk_sdmmc", RK3036_SDMMC_CON1, 0), + + MMC(SCLK_SDIO_DRV, "sdio_drv", "sclk_sdio", RK3036_SDIO_CON0, 1), + MMC(SCLK_SDIO_SAMPLE, "sdio_sample", "sclk_sdio", RK3036_SDIO_CON1, 0), + + MMC(SCLK_EMMC_DRV, "emmc_drv", "sclk_emmc", RK3036_EMMC_CON0, 1), + MMC(SCLK_EMMC_SAMPLE, "emmc_sample", "sclk_emmc", RK3036_EMMC_CON1, 0), + + /* I2S */ + COMPOSITE(0, "i2s_src", mux_pll_src_3plls_p, 0, + RK2928_CLKSEL_CON(3), 14, 2, MFLAGS, 0, 7, DFLAGS, + RK2928_CLKGATE_CON(0), 9, GFLAGS), + COMPOSITE_FRAC(0, "i2s_frac", "i2s_src", CLK_SET_RATE_PARENT, + RK2928_CLKSEL_CON(7), 0, + RK2928_CLKGATE_CON(0), 10, GFLAGS), + MUX(0, "i2s_pre", mux_i2s_pre_p, CLK_SET_RATE_PARENT, + RK2928_CLKSEL_CON(3), 8, 2, MFLAGS), + COMPOSITE_NODIV(SCLK_I2S_OUT, "i2s_clkout", mux_i2s_clkout_p, 0, + RK2928_CLKSEL_CON(3), 12, 1, MFLAGS, + RK2928_CLKGATE_CON(0), 13, GFLAGS), + GATE(SCLK_I2S, "sclk_i2s", "i2s_pre", CLK_SET_RATE_PARENT, + RK2928_CLKGATE_CON(0), 14, GFLAGS), + + /* SPDIF */ + COMPOSITE(0, "spdif_src", mux_pll_src_3plls_p, 0, + RK2928_CLKSEL_CON(5), 10, 2, MFLAGS, 0, 7, DFLAGS, + RK2928_CLKGATE_CON(2), 10, GFLAGS), + COMPOSITE_FRAC(0, "spdif_frac", "spdif_src", 0, + RK2928_CLKSEL_CON(9), 0, + RK2928_CLKGATE_CON(2), 12, GFLAGS), + MUX(SCLK_SPDIF, "sclk_spdif", mux_spdif_p, 0, + RK2928_CLKSEL_CON(5), 8, 2, MFLAGS), + + GATE(SCLK_OTGPHY0, "sclk_otgphy0", "xin12m", CLK_IGNORE_UNUSED, + RK2928_CLKGATE_CON(1), 5, GFLAGS), + + COMPOSITE(SCLK_GPU, "sclk_gpu", mux_pll_src_3plls_p, 0, + RK2928_CLKSEL_CON(34), 8, 2, MFLAGS, 0, 5, DFLAGS, + RK2928_CLKGATE_CON(3), 13, GFLAGS), + + COMPOSITE(SCLK_SPI, "sclk_spi", mux_pll_src_3plls_p, 0, + RK2928_CLKSEL_CON(25), 8, 2, MFLAGS, 0, 7, DFLAGS, + RK2928_CLKGATE_CON(2), 9, GFLAGS), + + COMPOSITE(SCLK_NANDC, "sclk_nandc", mux_pll_src_3plls_p, 0, + RK2928_CLKSEL_CON(16), 8, 2, MFLAGS, 10, 5, DFLAGS, + RK2928_CLKGATE_CON(10), 4, GFLAGS), + + COMPOSITE(SCLK_SFC, "sclk_sfc", mux_pll_src_apll_dpll_gpll_usb480m_p, 0, + RK2928_CLKSEL_CON(16), 0, 2, MFLAGS, 2, 5, DFLAGS, + RK2928_CLKGATE_CON(10), 5, GFLAGS), + + COMPOSITE_NOGATE(0, "mac_pll_src", mux_pll_src_3plls_p, 0, + RK2928_CLKSEL_CON(21), 0, 2, MFLAGS, 4, 5, DFLAGS), + /* for clk_mac_ref & clk_mac_refout */ + MUX(SCLK_MACREF, "mac_clk_ref", mux_mac_p, CLK_SET_RATE_PARENT, + RK2928_CLKSEL_CON(21), 3, 1, MFLAGS), + + COMPOSITE_NOMUX(SCLK_MAC, "mac_clk", "mac_clk_ref", 0, + RK2928_CLKSEL_CON(21), 9, 5, DFLAGS, + RK2928_CLKGATE_CON(2), 6, GFLAGS), + + /* HDMI */ + /* total clks: pin_sys_clk / pin_sck / pin_mclk / pin_vclk / pin_vclk_pllref */ + /* the same with dclk_lcdc */ + COMPOSITE(0, "dclk_hdmi_src", mux_pll_src_3plls_p, 0, + RK2928_CLKSEL_CON(28), 0, 2, MFLAGS, 8, 8, DFLAGS, + RK2928_CLKGATE_CON(3), 2, GFLAGS), + /* hdmi dclk from dclk_lcdc directly */ + MUX(SCLK_HDMI, "dclk_hdmi", mux_dclk_p, 0, + RK2928_CLKSEL_CON(31), 0, 1, MFLAGS), + + /* + * Clock-Architecture Diagram 3 + */ + + /* aclk_cpu gates */ + GATE(0, "sclk_intmem", "aclk_cpu", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(4), 12, GFLAGS), + GATE(0, "aclk_strc_sys", "aclk_cpu", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(4), 10, GFLAGS), + + /* hclk_cpu gates */ + GATE(HCLK_ROM, "hclk_rom", "hclk_cpu", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(5), 6, GFLAGS), + + /* pclk_cpu gates */ + GATE(PCLK_GRF, "pclk_grf", "pclk_cpu", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(5), 4, GFLAGS), + GATE(PCLK_DDRUPCTL, "pclk_ddrupctl", "pclk_cpu", 0, RK2928_CLKGATE_CON(5), 7, GFLAGS), + GATE(PCLK_ACODEC, "pclk_acodec", "pclk_cpu", 0, RK2928_CLKGATE_CON(5), 14, GFLAGS), + GATE(PCLK_HDMI, "pclk_hdmi", "pclk_cpu", 0, RK2928_CLKGATE_CON(3), 8, GFLAGS), + + /* aclk_vio gates */ + GATE(ACLK_VIO, "aclk_vio", "aclk_disp1_pre", 0, RK2928_CLKGATE_CON(6), 13, GFLAGS), + GATE(ACLK_LCDC, "aclk_lcdc", "aclk_disp1_pre", 0, RK2928_CLKGATE_CON(9), 6, GFLAGS), + + GATE(HCLK_VIO_BUS, "hclk_vio_bus", "hclk_disp_pre", 0, RK2928_CLKGATE_CON(6), 12, GFLAGS), + GATE(HCLK_LCDC, "hclk_lcdc", "hclk_disp_pre", 0, RK2928_CLKGATE_CON(9), 5, GFLAGS), + + /* aclk_video gates */ + GATE(HCLK_LCDC, "hclk_vcodec", "hclk_disp_pre", 0, RK2928_CLKGATE_CON(3), 12, GFLAGS), + + /* xin24m gates */ + GATE(SCLK_PVTM_CORE, "sclk_pvtm_core", "xin24m", 0, RK2928_CLKGATE_CON(10), 0, GFLAGS), + GATE(SCLK_PVTM_GPU, "sclk_pvtm_gpu", "xin24m", 0, RK2928_CLKGATE_CON(10), 1, GFLAGS), + + /* aclk_peri gates */ + GATE(0, "aclk_peri_axi_matrix", "aclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(4), 3, GFLAGS), + GATE(0, "aclk_cpu_peri", "aclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(4), 2, GFLAGS), + GATE(ACLK_DMAC2, "aclk_dmac2", "aclk_peri", 0, RK2928_CLKGATE_CON(5), 1, GFLAGS), + GATE(0, "aclk_peri_niu", "aclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(9), 15, GFLAGS), + + /* hclk_peri gates */ + GATE(0, "hclk_peri_matrix", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(4), 0, GFLAGS), + GATE(0, "hclk_usb_peri", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(9), 13, GFLAGS), + GATE(0, "hclk_peri_arbi", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(9), 14, GFLAGS), + GATE(HCLK_NANDC, "hclk_nandc", "hclk_peri", 0, RK2928_CLKGATE_CON(5), 9, GFLAGS), + GATE(HCLK_SDMMC, "hclk_sdmmc", "hclk_peri", 0, RK2928_CLKGATE_CON(5), 10, GFLAGS), + GATE(HCLK_SDIO, "hclk_sdio", "hclk_peri", 0, RK2928_CLKGATE_CON(5), 11, GFLAGS), + GATE(HCLK_EMMC, "hclk_emmc", "hclk_peri", 0, RK2928_CLKGATE_CON(7), 0, GFLAGS), + GATE(HCLK_OTG0, "hclk_otg0", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(5), 13, GFLAGS), + GATE(HCLK_OTG1, "hclk_otg1", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(7), 3, GFLAGS), + GATE(HCLK_I2S, "hclk_i2s", "hclk_peri", 0, RK2928_CLKGATE_CON(7), 2, GFLAGS), + GATE(0, "hclk_sfc", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(3), 14, GFLAGS), + GATE(0, "hclk_mac", "hclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(3), 15, GFLAGS), + + /* pclk_peri gates */ + GATE(0, "pclk_peri_matrix", "pclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(4), 1, GFLAGS), + GATE(0, "pclk_efuse", "pclk_peri", CLK_IGNORE_UNUSED, RK2928_CLKGATE_CON(5), 2, GFLAGS), + GATE(PCLK_TIMER, "pclk_timer0", "pclk_peri", 0, RK2928_CLKGATE_CON(7), 7, GFLAGS), + GATE(PCLK_PWM, "pclk_pwm", "pclk_peri", 0, RK2928_CLKGATE_CON(7), 10, GFLAGS), + GATE(PCLK_SPI, "pclk_spi", "pclk_peri", 0, RK2928_CLKGATE_CON(7), 12, GFLAGS), + GATE(PCLK_WDT, "pclk_wdt", "pclk_peri", 0, RK2928_CLKGATE_CON(7), 15, GFLAGS), + GATE(PCLK_UART0, "pclk_uart0", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 0, GFLAGS), + GATE(PCLK_UART1, "pclk_uart1", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 1, GFLAGS), + GATE(PCLK_UART2, "pclk_uart2", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 2, GFLAGS), + GATE(PCLK_I2C0, "pclk_i2c0", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 4, GFLAGS), + GATE(PCLK_I2C1, "pclk_i2c1", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 5, GFLAGS), + GATE(PCLK_I2C2, "pclk_i2c2", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 6, GFLAGS), + GATE(PCLK_GPIO0, "pclk_gpio0", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 9, GFLAGS), + GATE(PCLK_GPIO1, "pclk_gpio1", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 10, GFLAGS), + GATE(PCLK_GPIO2, "pclk_gpio2", "pclk_peri", 0, RK2928_CLKGATE_CON(8), 11, GFLAGS), +}; + +static const char *const rk3036_critical_clocks[] __initconst = { + "aclk_cpu", + "aclk_peri", + "hclk_peri", + "pclk_peri", +}; + +static void __init rk3036_clk_init(struct device_node *np) +{ + void __iomem *reg_base; + struct clk *clk; + + reg_base = of_iomap(np, 0); + if (!reg_base) { + pr_err("%s: could not map cru region\n", __func__); + return; + } + + rockchip_clk_init(np, reg_base, CLK_NR_CLKS); + + /* xin12m is created by an cru-internal divider */ + clk = clk_register_fixed_factor(NULL, "xin12m", "xin24m", 0, 1, 2); + if (IS_ERR(clk)) + pr_warn("%s: could not register clock xin12m: %ld\n", + __func__, PTR_ERR(clk)); + + clk = clk_register_fixed_factor(NULL, "usb480m", "xin24m", 0, 20, 1); + if (IS_ERR(clk)) + pr_warn("%s: could not register clock usb480m: %ld\n", + __func__, PTR_ERR(clk)); + + clk = clk_register_fixed_factor(NULL, "ddrphy", "ddrphy2x", 0, 1, 2); + if (IS_ERR(clk)) + pr_warn("%s: could not register clock ddrphy: %ld\n", + __func__, PTR_ERR(clk)); + + clk = clk_register_fixed_factor(NULL, "hclk_vcodec_pre", + "aclk_vcodec", 0, 1, 4); + if (IS_ERR(clk)) + pr_warn("%s: could not register clock hclk_vcodec_pre: %ld\n", + __func__, PTR_ERR(clk)); + + clk = clk_register_fixed_factor(NULL, "sclk_macref_out", + "hclk_peri_src", 0, 1, 2); + if (IS_ERR(clk)) + pr_warn("%s: could not register clock sclk_macref_out: %ld\n", + __func__, PTR_ERR(clk)); + + rockchip_clk_register_plls(rk3036_pll_clks, + ARRAY_SIZE(rk3036_pll_clks), + RK3036_GRF_SOC_STATUS0); + rockchip_clk_register_branches(rk3036_clk_branches, + ARRAY_SIZE(rk3036_clk_branches)); + rockchip_clk_protect_critical(rk3036_critical_clocks, + ARRAY_SIZE(rk3036_critical_clocks)); + + rockchip_clk_register_armclk(ARMCLK, "armclk", + mux_armclk_p, ARRAY_SIZE(mux_armclk_p), + &rk3036_cpuclk_data, rk3036_cpuclk_rates, + ARRAY_SIZE(rk3036_cpuclk_rates)); + + rockchip_register_softrst(np, 9, reg_base + RK2928_SOFTRST_CON(0), + ROCKCHIP_SOFTRST_HIWORD_MASK); + + rockchip_register_restart_notifier(RK2928_GLB_SRST_FST); +} +CLK_OF_DECLARE(rk3036_cru, "rockchip,rk3036-cru", rk3036_clk_init); diff --git a/drivers/clk/rockchip/clk.h b/drivers/clk/rockchip/clk.h index dc8ecb2..4b79f34 100644 --- a/drivers/clk/rockchip/clk.h +++ b/drivers/clk/rockchip/clk.h @@ -2,6 +2,9 @@ * Copyright (c) 2014 MundoReader S.L. * Author: Heiko Stuebner <heiko@sntech.de> * + * Copyright (c) 2015 Rockchip Electronics Co. Ltd. + * Author: Xing Zheng <zhengxing@rock-chips.com> + * * based on * * samsung/clk.h @@ -40,6 +43,13 @@ struct clk; #define RK2928_SOFTRST_CON(x) ((x) * 0x4 + 0x110) #define RK2928_MISC_CON 0x134 +#define RK3036_SDMMC_CON0 0x144 +#define RK3036_SDMMC_CON1 0x148 +#define RK3036_SDIO_CON0 0x14c +#define RK3036_SDIO_CON1 0x150 +#define RK3036_EMMC_CON0 0x154 +#define RK3036_EMMC_CON1 0x158 + #define RK3288_PLL_CON(x) RK2928_PLL_CON(x) #define RK3288_MODE_CON 0x50 #define RK3288_CLKSEL_CON(x) ((x) * 0x4 + 0x60) @@ -74,9 +84,22 @@ struct clk; #define RK3368_EMMC_CON1 0x41c enum rockchip_pll_type { + pll_rk3036, pll_rk3066, }; +#define RK3036_PLL_RATE(_rate, _refdiv, _fbdiv, _postdiv1, \ + _postdiv2, _dsmpd, _frac) \ +{ \ + .rate = _rate##U, \ + .fbdiv = _fbdiv, \ + .postdiv1 = _postdiv1, \ + .refdiv = _refdiv, \ + .postdiv2 = _postdiv2, \ + .dsmpd = _dsmpd, \ + .frac = _frac, \ +} + #define RK3066_PLL_RATE(_rate, _nr, _nf, _no) \ { \ .rate = _rate##U, \ @@ -101,6 +124,13 @@ struct rockchip_pll_rate_table { unsigned int nf; unsigned int no; unsigned int nb; + /* for RK3036 */ + unsigned int fbdiv; + unsigned int postdiv1; + unsigned int refdiv; + unsigned int postdiv2; + unsigned int dsmpd; + unsigned int frac; }; /** -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v5 3/8] clk: rockchip: add clock controller for rk3036 2015-10-26 4:25 ` [PATCH v5 3/8] clk: rockchip: add clock controller for rk3036 Xing Zheng @ 2015-10-28 7:53 ` Heiko Stuebner 0 siblings, 0 replies; 9+ messages in thread From: Heiko Stuebner @ 2015-10-28 7:53 UTC (permalink / raw) To: linux-arm-kernel Am Montag, 26. Oktober 2015, 12:25:34 schrieb Xing Zheng: > diff --git a/drivers/clk/rockchip/clk.h b/drivers/clk/rockchip/clk.h > index dc8ecb2..4b79f34 100644 > --- a/drivers/clk/rockchip/clk.h > +++ b/drivers/clk/rockchip/clk.h > @@ -2,6 +2,9 @@ > * Copyright (c) 2014 MundoReader S.L. > * Author: Heiko Stuebner <heiko@sntech.de> > * > + * Copyright (c) 2015 Rockchip Electronics Co. Ltd. > + * Author: Xing Zheng <zhengxing@rock-chips.com> > + * > * based on > * > * samsung/clk.h > @@ -40,6 +43,13 @@ struct clk; > #define RK2928_SOFTRST_CON(x) ((x) * 0x4 + 0x110) > #define RK2928_MISC_CON 0x134 > > +#define RK3036_SDMMC_CON0 0x144 > +#define RK3036_SDMMC_CON1 0x148 > +#define RK3036_SDIO_CON0 0x14c > +#define RK3036_SDIO_CON1 0x150 > +#define RK3036_EMMC_CON0 0x154 > +#define RK3036_EMMC_CON1 0x158 > + > #define RK3288_PLL_CON(x) RK2928_PLL_CON(x) > #define RK3288_MODE_CON 0x50 > #define RK3288_CLKSEL_CON(x) ((x) * 0x4 + 0x60) > @@ -74,9 +84,22 @@ struct clk; > #define RK3368_EMMC_CON1 0x41c > > enum rockchip_pll_type { > + pll_rk3036, > pll_rk3066, > }; > > +#define RK3036_PLL_RATE(_rate, _refdiv, _fbdiv, _postdiv1, \ > + _postdiv2, _dsmpd, _frac) \ > +{ \ > + .rate = _rate##U, \ > + .fbdiv = _fbdiv, \ > + .postdiv1 = _postdiv1, \ > + .refdiv = _refdiv, \ > + .postdiv2 = _postdiv2, \ > + .dsmpd = _dsmpd, \ > + .frac = _frac, \ > +} > + > #define RK3066_PLL_RATE(_rate, _nr, _nf, _no) \ > { \ > .rate = _rate##U, \ > @@ -101,6 +124,13 @@ struct rockchip_pll_rate_table { > unsigned int nf; > unsigned int no; > unsigned int nb; > + /* for RK3036 */ > + unsigned int fbdiv; > + unsigned int postdiv1; > + unsigned int refdiv; > + unsigned int postdiv2; > + unsigned int dsmpd; > + unsigned int frac; > }; > > /** the changes to our clk.h should be part of the addition of the pll itself (your current patch4) and that patch should then trade places with this one, so you add the complete pll type first and this clock controller afterwards. Heiko ^ permalink raw reply [flat|nested] 9+ messages in thread
* [PATCH v5 4/8] clk: rockchip: add new pll-type for rk3036 and similar socs 2015-10-26 4:25 [PATCH v5 0/8] Build and support rk3036 SoC platform Xing Zheng 2015-10-26 4:25 ` [PATCH v5 1/8] dt-bindings: add documentation of rk3036 clock controller Xing Zheng 2015-10-26 4:25 ` [PATCH v5 3/8] clk: rockchip: add clock controller for rk3036 Xing Zheng @ 2015-10-26 4:25 ` Xing Zheng 2015-10-26 4:31 ` [PATCH v5 5/8] ARM: dts: rockchip: add core rk3036 dts Xing Zheng ` (3 subsequent siblings) 6 siblings, 0 replies; 9+ messages in thread From: Xing Zheng @ 2015-10-26 4:25 UTC (permalink / raw) To: linux-arm-kernel The rk3036's pll and clock are different with base on the rk3066(rk3188, rk3288, rk3368 use it), there are different adjust foctors and control registers, so these should be independent and separate from the series of rk3066s. Signed-off-by: Xing Zheng <zhengxing@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> --- Changes in v5: None drivers/clk/rockchip/clk-pll.c | 249 +++++++++++++++++++++++++++++++++++++++- 1 file changed, 248 insertions(+), 1 deletion(-) diff --git a/drivers/clk/rockchip/clk-pll.c b/drivers/clk/rockchip/clk-pll.c index 4881eb8..83ba1e9 100644 --- a/drivers/clk/rockchip/clk-pll.c +++ b/drivers/clk/rockchip/clk-pll.c @@ -2,6 +2,9 @@ * Copyright (c) 2014 MundoReader S.L. * Author: Heiko Stuebner <heiko@sntech.de> * + * Copyright (c) 2015 Rockchip Electronics Co. Ltd. + * Author: Xing Zheng <zhengxing@rock-chips.com> + * * This program is free software; you can redistribute it and/or modify * it under the terms of the GNU General Public License as published by * the Free Software Foundation; either version 2 of the License, or @@ -19,6 +22,7 @@ #include <linux/delay.h> #include <linux/clk-provider.h> #include <linux/regmap.h> +#include <linux/clk.h> #include "clk.h" #define PLL_MODE_MASK 0x3 @@ -108,6 +112,243 @@ static int rockchip_pll_wait_lock(struct rockchip_clk_pll *pll) } /** + * PLL used in RK3036 + */ + +#define RK3036_PLLCON(i) (i * 0x4) +#define RK3036_PLLCON0_FBDIV_MASK 0xfff +#define RK3036_PLLCON0_FBDIV_SHIFT 0 +#define RK3036_PLLCON0_POSTDIV1_MASK 0x7 +#define RK3036_PLLCON0_POSTDIV1_SHIFT 12 +#define RK3036_PLLCON1_REFDIV_MASK 0x3f +#define RK3036_PLLCON1_REFDIV_SHIFT 0 +#define RK3036_PLLCON1_POSTDIV2_MASK 0x7 +#define RK3036_PLLCON1_POSTDIV2_SHIFT 6 +#define RK3036_PLLCON1_DSMPD_MASK 0x1 +#define RK3036_PLLCON1_DSMPD_SHIFT 12 +#define RK3036_PLLCON2_FRAC_MASK 0xffffff +#define RK3036_PLLCON2_FRAC_SHIFT 0 + +#define RK3036_PLLCON1_PWRDOWN (1 << 13) + +static void rockchip_rk3036_pll_get_params(struct rockchip_clk_pll *pll, + struct rockchip_pll_rate_table *rate) +{ + u32 pllcon; + + pllcon = readl_relaxed(pll->reg_base + RK3036_PLLCON(0)); + rate->fbdiv = ((pllcon >> RK3036_PLLCON0_FBDIV_SHIFT) & RK3036_PLLCON0_FBDIV_MASK); + rate->postdiv1 = ((pllcon >> RK3036_PLLCON0_POSTDIV1_SHIFT) & RK3036_PLLCON0_POSTDIV1_MASK); + + pllcon = readl_relaxed(pll->reg_base + RK3036_PLLCON(1)); + rate->refdiv = ((pllcon >> RK3036_PLLCON1_REFDIV_SHIFT) & RK3036_PLLCON1_REFDIV_MASK); + rate->postdiv2 = ((pllcon >> RK3036_PLLCON1_POSTDIV2_SHIFT) & RK3036_PLLCON1_POSTDIV2_MASK); + rate->dsmpd = ((pllcon >> RK3036_PLLCON1_DSMPD_SHIFT) & RK3036_PLLCON1_DSMPD_MASK); + + pllcon = readl_relaxed(pll->reg_base + RK3036_PLLCON(2)); + rate->frac = ((pllcon >> RK3036_PLLCON2_FRAC_SHIFT) & RK3036_PLLCON2_FRAC_MASK); +} + +static unsigned long rockchip_rk3036_pll_recalc_rate(struct clk_hw *hw, + unsigned long prate) +{ + struct rockchip_clk_pll *pll = to_rockchip_clk_pll(hw); + struct rockchip_pll_rate_table cur; + u64 rate64 = prate; + + rockchip_rk3036_pll_get_params(pll, &cur); + + rate64 *= cur.fbdiv; + do_div(rate64, cur.refdiv); + + if (cur.dsmpd == 0) { + /* fractional mode */ + u64 frac_rate64 = prate * cur.frac; + + do_div(frac_rate64, cur.refdiv); + rate64 += frac_rate64 >> 24; + } + + do_div(rate64, cur.postdiv1); + do_div(rate64, cur.postdiv2); + + return (unsigned long)rate64; +} + +static int rockchip_rk3036_pll_set_params(struct rockchip_clk_pll *pll, + const struct rockchip_pll_rate_table *rate) +{ + const struct clk_ops *pll_mux_ops = pll->pll_mux_ops; + struct clk_mux *pll_mux = &pll->pll_mux; + struct rockchip_pll_rate_table cur; + u32 pllcon; + int rate_change_remuxed = 0; + int cur_parent; + int ret; + + pr_debug("%s: rate settings for %lu fbdiv: %d, postdiv1: %d, refdiv: %d, postdiv2: %d, dsmpd: %d, frac: %d\n", + __func__, rate->rate, rate->fbdiv, rate->postdiv1, rate->refdiv, + rate->postdiv2, rate->dsmpd, rate->frac); + + rockchip_rk3036_pll_get_params(pll, &cur); + cur.rate = 0; + + cur_parent = pll_mux_ops->get_parent(&pll_mux->hw); + if (cur_parent == PLL_MODE_NORM) { + pll_mux_ops->set_parent(&pll_mux->hw, PLL_MODE_SLOW); + rate_change_remuxed = 1; + } + + /* update pll values */ + writel_relaxed(HIWORD_UPDATE(rate->fbdiv, RK3036_PLLCON0_FBDIV_MASK, + RK3036_PLLCON0_FBDIV_SHIFT) | + HIWORD_UPDATE(rate->postdiv1, RK3036_PLLCON0_POSTDIV1_MASK, + RK3036_PLLCON0_POSTDIV1_SHIFT), + pll->reg_base + RK3036_PLLCON(0)); + + writel_relaxed(HIWORD_UPDATE(rate->refdiv, RK3036_PLLCON1_REFDIV_MASK, + RK3036_PLLCON1_REFDIV_SHIFT) | + HIWORD_UPDATE(rate->postdiv2, RK3036_PLLCON1_POSTDIV2_MASK, + RK3036_PLLCON1_POSTDIV2_SHIFT) | + HIWORD_UPDATE(rate->dsmpd, RK3036_PLLCON1_DSMPD_MASK, + RK3036_PLLCON1_DSMPD_SHIFT), + pll->reg_base + RK3036_PLLCON(1)); + + /* GPLL CON2 is not HIWORD_MASK */ + pllcon = readl_relaxed(pll->reg_base + RK3036_PLLCON(2)); + pllcon &= ~(RK3036_PLLCON2_FRAC_MASK << RK3036_PLLCON2_FRAC_SHIFT); + pllcon |= rate->frac << RK3036_PLLCON2_FRAC_SHIFT; + writel_relaxed(pllcon, pll->reg_base + RK3036_PLLCON(2)); + + /* wait for the pll to lock */ + ret = rockchip_pll_wait_lock(pll); + if (ret) { + pr_warn("%s: pll update unsucessful, trying to restore old params\n", + __func__); + rockchip_rk3036_pll_set_params(pll, &cur); + } + + if (rate_change_remuxed) + pll_mux_ops->set_parent(&pll_mux->hw, PLL_MODE_NORM); + + return ret; +} + +static int rockchip_rk3036_pll_set_rate(struct clk_hw *hw, unsigned long drate, + unsigned long prate) +{ + struct rockchip_clk_pll *pll = to_rockchip_clk_pll(hw); + const struct rockchip_pll_rate_table *rate; + unsigned long old_rate = rockchip_rk3036_pll_recalc_rate(hw, prate); + struct regmap *grf = rockchip_clk_get_grf(); + + if (IS_ERR(grf)) { + pr_debug("%s: grf regmap not available, aborting rate change\n", + __func__); + return PTR_ERR(grf); + } + + pr_debug("%s: changing %s from %lu to %lu with a parent rate of %lu\n", + __func__, __clk_get_name(hw->clk), old_rate, drate, prate); + + /* Get required rate settings from table */ + rate = rockchip_get_pll_settings(pll, drate); + if (!rate) { + pr_err("%s: Invalid rate : %lu for pll clk %s\n", __func__, + drate, __clk_get_name(hw->clk)); + return -EINVAL; + } + + return rockchip_rk3036_pll_set_params(pll, rate); +} + +static int rockchip_rk3036_pll_enable(struct clk_hw *hw) +{ + struct rockchip_clk_pll *pll = to_rockchip_clk_pll(hw); + + writel(HIWORD_UPDATE(0, RK3036_PLLCON1_PWRDOWN, 0), + pll->reg_base + RK3036_PLLCON(1)); + + return 0; +} + +static void rockchip_rk3036_pll_disable(struct clk_hw *hw) +{ + struct rockchip_clk_pll *pll = to_rockchip_clk_pll(hw); + + writel(HIWORD_UPDATE(RK3036_PLLCON1_PWRDOWN, + RK3036_PLLCON1_PWRDOWN, 0), + pll->reg_base + RK3036_PLLCON(1)); +} + +static int rockchip_rk3036_pll_is_enabled(struct clk_hw *hw) +{ + struct rockchip_clk_pll *pll = to_rockchip_clk_pll(hw); + u32 pllcon = readl(pll->reg_base + RK3036_PLLCON(1)); + + return !(pllcon & RK3036_PLLCON1_PWRDOWN); +} + +static void rockchip_rk3036_pll_init(struct clk_hw *hw) +{ + struct rockchip_clk_pll *pll = to_rockchip_clk_pll(hw); + const struct rockchip_pll_rate_table *rate; + struct rockchip_pll_rate_table cur; + unsigned long drate; + + if (!(pll->flags & ROCKCHIP_PLL_SYNC_RATE)) + return; + + drate = clk_hw_get_rate(hw); + rate = rockchip_get_pll_settings(pll, drate); + + /* when no rate setting for the current rate, rely on clk_set_rate */ + if (!rate) + return; + + rockchip_rk3036_pll_get_params(pll, &cur); + + pr_debug("%s: pll %s@%lu: Hz\n", __func__, __clk_get_name(hw->clk), drate); + pr_debug("old - fbdiv: %d, postdiv1: %d, refdiv: %d, postdiv2: %d, dsmpd: %d, frac: %d\n", + cur.fbdiv, cur.postdiv1, cur.refdiv, cur.postdiv2, cur.dsmpd, cur.frac); + pr_debug("new - fbdiv: %d, postdiv1: %d, refdiv: %d, postdiv2: %d, dsmpd: %d, frac: %d\n", + rate->fbdiv, rate->postdiv1, rate->refdiv, rate->postdiv2, rate->dsmpd, rate->frac); + + if (rate->fbdiv != cur.fbdiv || rate->postdiv1 != cur.postdiv1 || + rate->refdiv != cur.refdiv || rate->postdiv2 != cur.postdiv2 || + rate->dsmpd != cur.dsmpd || rate->frac != cur.frac) { + struct clk *parent = clk_get_parent(hw->clk); + + if (!parent) { + pr_warn("%s: parent of %s not available\n", + __func__, __clk_get_name(hw->clk)); + return; + } + + pr_debug("%s: pll %s: rate params do not match rate table, adjusting\n", + __func__, __clk_get_name(hw->clk)); + rockchip_rk3036_pll_set_params(pll, rate); + } +} + +static const struct clk_ops rockchip_rk3036_pll_clk_norate_ops = { + .recalc_rate = rockchip_rk3036_pll_recalc_rate, + .enable = rockchip_rk3036_pll_enable, + .disable = rockchip_rk3036_pll_disable, + .is_enabled = rockchip_rk3036_pll_is_enabled, +}; + +static const struct clk_ops rockchip_rk3036_pll_clk_ops = { + .recalc_rate = rockchip_rk3036_pll_recalc_rate, + .round_rate = rockchip_pll_round_rate, + .set_rate = rockchip_rk3036_pll_set_rate, + .enable = rockchip_rk3036_pll_enable, + .disable = rockchip_rk3036_pll_disable, + .is_enabled = rockchip_rk3036_pll_is_enabled, + .init = rockchip_rk3036_pll_init, +}; + +/** * PLL used in RK3066, RK3188 and RK3288 */ @@ -376,7 +617,7 @@ struct clk *rockchip_clk_register_pll(enum rockchip_pll_type pll_type, pll_mux->lock = lock; pll_mux->hw.init = &init; - if (pll_type == pll_rk3066) + if (pll_type == pll_rk3036 || pll_type == pll_rk3066) pll_mux->flags |= CLK_MUX_HIWORD_MASK; /* the actual muxing is xin24m, pll-output, xin32k */ @@ -421,6 +662,12 @@ struct clk *rockchip_clk_register_pll(enum rockchip_pll_type pll_type, } switch (pll_type) { + case pll_rk3036: + if (!pll->rate_table) + init.ops = &rockchip_rk3036_pll_clk_norate_ops; + else + init.ops = &rockchip_rk3036_pll_clk_ops; + break; case pll_rk3066: if (!pll->rate_table) init.ops = &rockchip_rk3066_pll_clk_norate_ops; -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v5 5/8] ARM: dts: rockchip: add core rk3036 dts 2015-10-26 4:25 [PATCH v5 0/8] Build and support rk3036 SoC platform Xing Zheng ` (2 preceding siblings ...) 2015-10-26 4:25 ` [PATCH v5 4/8] clk: rockchip: add new pll-type for rk3036 and similar socs Xing Zheng @ 2015-10-26 4:31 ` Xing Zheng 2015-10-26 4:32 ` [PATCH v5 6/8] ARM: rockchip: add support smp for rk3036 Xing Zheng ` (2 subsequent siblings) 6 siblings, 0 replies; 9+ messages in thread From: Xing Zheng @ 2015-10-26 4:31 UTC (permalink / raw) To: linux-arm-kernel Initial release for rk3036, node definitions rk3036 sdk board. Signed-off-by: Xing Zheng <zhengxing@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> --- Changes in v5: None arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/rk3036-evb.dts | 64 +++++ arch/arm/boot/dts/rk3036.dtsi | 536 ++++++++++++++++++++++++++++++++++++++ 3 files changed, 601 insertions(+) create mode 100644 arch/arm/boot/dts/rk3036-evb.dts create mode 100644 arch/arm/boot/dts/rk3036.dtsi diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 7d3e495..3e4e089 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -510,6 +510,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \ dtb-$(CONFIG_ARCH_REALVIEW) += \ arm-realview-pb1176.dtb dtb-$(CONFIG_ARCH_ROCKCHIP) += \ + rk3036-evb.dtb \ rk3066a-bqcurie2.dtb \ rk3066a-marsboard.dtb \ rk3066a-rayeager.dtb \ diff --git a/arch/arm/boot/dts/rk3036-evb.dts b/arch/arm/boot/dts/rk3036-evb.dts new file mode 100644 index 0000000..28a0336 --- /dev/null +++ b/arch/arm/boot/dts/rk3036-evb.dts @@ -0,0 +1,64 @@ +/* + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +/dts-v1/; + +#include "rk3036.dtsi" + +/ { + model = "Rockchip RK3036 Evaluation board"; + compatible = "rockchip,rk3036-evb", "rockchip,rk3036"; +}; + +&i2c1 { + status = "okay"; + + hym8563: hym8563 at 51 { + compatible = "haoyu,hym8563"; + reg = <0x51>; + #clock-cells = <0>; + clock-frequency = <32768>; + clock-output-names = "xin32k"; + }; +}; + +&uart2 { + status = "okay"; +}; diff --git a/arch/arm/boot/dts/rk3036.dtsi b/arch/arm/boot/dts/rk3036.dtsi new file mode 100644 index 0000000..8f3a069 --- /dev/null +++ b/arch/arm/boot/dts/rk3036.dtsi @@ -0,0 +1,536 @@ +/* + * This file is dual-licensed: you can use it either under the terms + * of the GPL or the X11 license, at your option. Note that this dual + * licensing only applies to this file, and not this project as a + * whole. + * + * a) This file is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License as + * published by the Free Software Foundation; either version 2 of the + * License, or (at your option) any later version. + * + * This file is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * Or, alternatively, + * + * b) Permission is hereby granted, free of charge, to any person + * obtaining a copy of this software and associated documentation + * files (the "Software"), to deal in the Software without + * restriction, including without limitation the rights to use, + * copy, modify, merge, publish, distribute, sublicense, and/or + * sell copies of the Software, and to permit persons to whom the + * Software is furnished to do so, subject to the following + * conditions: + * + * The above copyright notice and this permission notice shall be + * included in all copies or substantial portions of the Software. + * + * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND, + * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES + * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND + * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT + * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY, + * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING + * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR + * OTHER DEALINGS IN THE SOFTWARE. + */ + +#include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/irq.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/pinctrl/rockchip.h> +#include <dt-bindings/clock/rk3036-cru.h> +#include "skeleton.dtsi" + +/ { + compatible = "rockchip,rk3036"; + + interrupt-parent = <&gic>; + + aliases { + i2c1 = &i2c1; + serial0 = &uart0; + serial1 = &uart1; + serial2 = &uart2; + }; + + memory { + device_type = "memory"; + reg = <0x60000000 0x40000000>; + }; + + arm-pmu { + compatible = "arm,cortex-a7-pmu"; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; + interrupt-affinity = <&cpu0>, <&cpu1>; + }; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu0: cpu at f00 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0xf00>; + operating-points = < + /* KHz uV */ + 816000 1000000 + >; + clock-latency = <40000>; + clocks = <&cru ARMCLK>; + resets = <&cru SRST_CORE0>; + }; + cpu1: cpu at f01 { + device_type = "cpu"; + compatible = "arm,cortex-a7"; + reg = <0xf01>; + resets = <&cru SRST_CORE1>; + }; + }; + + amba { + compatible = "arm,amba-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + pdma: pdma at 20078000 { + compatible = "arm,pl330", "arm,primecell"; + reg = <0x20078000 0x4000>; + interrupts = <GIC_SPI 0 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 1 IRQ_TYPE_LEVEL_HIGH>; + #dma-cells = <1>; + clocks = <&cru ACLK_DMAC2>; + clock-names = "apb_pclk"; + }; + }; + + xin24m: oscillator { + compatible = "fixed-clock"; + clock-frequency = <24000000>; + clock-output-names = "xin24m"; + #clock-cells = <0>; + }; + + timer { + compatible = "arm,armv7-timer"; + arm,cpu-registers-not-fw-configured; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, + <GIC_PPI 14 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, + <GIC_PPI 11 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>, + <GIC_PPI 10 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>; + clock-frequency = <24000000>; + }; + + gic: interrupt-controller at 10139000 { + compatible = "arm,gic-400"; + interrupt-controller; + #interrupt-cells = <3>; + #address-cells = <0>; + + reg = <0x10139000 0x1000>, + <0x1013a000 0x1000>, + <0x1013c000 0x2000>, + <0x1013e000 0x2000>; + interrupts = <GIC_PPI 9 0xf04>; + }; + + bus_intmem at 10080000 { + compatible = "mmio-sram"; + reg = <0x10080000 0x2000>; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0 0x10080000 0x2000>; + }; + + cru: clock-controller at 20000000 { + compatible = "rockchip,rk3036-cru"; + reg = <0x20000000 0x1000>; + rockchip,grf = <&grf>; + #clock-cells = <1>; + #reset-cells = <1>; + assigned-clocks = <&cru PLL_GPLL>; + assigned-clock-rates = <594000000>; + }; + + grf: syscon at 20008000 { + compatible = "rockchip,rk3036-grf", "syscon"; + reg = <0x20008000 0x1000>; + }; + + pwm0: pwm at 20050000 { + compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm"; + reg = <0x20050000 0x10>; + #pwm-cells = <3>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm0_pin>; + clocks = <&cru PCLK_PWM>; + clock-names = "pwm"; + status = "disabled"; + }; + + pwm1: pwm at 20050010 { + compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm"; + reg = <0x20050010 0x10>; + #pwm-cells = <3>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm1_pin>; + clocks = <&cru PCLK_PWM>; + clock-names = "pwm"; + status = "disabled"; + }; + + pwm2: pwm at 20050020 { + compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm"; + reg = <0x20050020 0x10>; + #pwm-cells = <3>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm2_pin>; + clocks = <&cru PCLK_PWM>; + clock-names = "pwm"; + status = "disabled"; + }; + + pwm3: pwm at 20050030 { + compatible = "rockchip,rk3036-pwm", "rockchip,rk2928-pwm"; + reg = <0x20050030 0x10>; + #pwm-cells = <2>; + pinctrl-names = "default"; + pinctrl-0 = <&pwm3_pin>; + clocks = <&cru PCLK_PWM>; + clock-names = "pwm"; + status = "disabled"; + }; + + acodec: acodec-ana at 20030000 { + compatible = "rk3036-codec"; + reg = <0x20030000 0x4000>; + rockchip,grf = <&grf>; + clock-names = "acodec_pclk"; + clocks = <&cru PCLK_ACODEC>; + status = "disabled"; + }; + + emmc: dwmmc at 1021c000 { + compatible = "rockchip,rk3288-dw-mshc"; + clock-frequency = <37500000>; + clock-freq-min-max = <400000 37500000>; + clocks = <&cru HCLK_EMMC>, <&cru SCLK_EMMC>, + <&cru SCLK_EMMC_DRV>, <&cru SCLK_EMMC_SAMPLE>; + clock-names = "biu", "ciu", "ciu_drv", "ciu_sample"; + dmas = <&pdma 12>; + dma-names = "rx-tx"; + fifo-depth = <0x100>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; + reg = <0x1021c000 0x4000>; + broken-cd; + bus-width = <8>; + cap-mmc-highspeed; + mmc-ddr-1_8v; + disable-wp; + non-removable; + num-slots = <1>; + default-sample-phase = <158>; + pinctrl-names = "default"; + pinctrl-0 = <&emmc_clk &emmc_cmd &emmc_bus8>; + status = "disabled"; + }; + + i2c0: i2c at 20072000 { + compatible = "rockchip,rk3288-i2c"; + reg = <0x20072000 0x1000>; + interrupts = <GIC_SPI 24 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clock-names = "i2c"; + clocks = <&cru PCLK_I2C0>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c0_xfer>; + status = "disabled"; + }; + + i2c1: i2c at 20056000 { + compatible = "rockchip,rk3288-i2c"; + reg = <0x20056000 0x1000>; + interrupts = <GIC_SPI 25 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clock-names = "i2c"; + clocks = <&cru PCLK_I2C1>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c1_xfer>; + status = "disabled"; + }; + + i2c2: i2c at 2005a000 { + compatible = "rockchip,rk3288-i2c"; + reg = <0x2005a000 0x1000>; + interrupts = <GIC_SPI 26 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + clock-names = "i2c"; + clocks = <&cru PCLK_I2C2>; + pinctrl-names = "default"; + pinctrl-0 = <&i2c2_xfer>; + status = "disabled"; + }; + + i2s: i2s at 10220000 { + compatible = "rockchip,rk3036-i2s", "rockchip,rk3066-i2s"; + reg = <0x10220000 0x4000>; + interrupts = <GIC_SPI 51 IRQ_TYPE_LEVEL_HIGH>; + #address-cells = <1>; + #size-cells = <0>; + dmas = <&pdma 0>, <&pdma 1>; + dma-names = "tx", "rx"; + clock-names = "i2s_hclk", "i2s_clk"; + clocks = <&cru HCLK_I2S>, <&cru SCLK_I2S>; + pinctrl-names = "default"; + pinctrl-0 = <&i2s_bus>; + status = "disabled"; + }; + + uart0: serial at 20060000 { + compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart"; + reg = <0x20060000 0x100>; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clock-frequency = <24000000>; + clocks = <&cru SCLK_UART0>, <&cru PCLK_UART0>; + clock-names = "baudclk", "apb_pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&uart0_xfer &uart0_cts &uart0_rts>; + status = "disabled"; + }; + + uart1: serial at 20064000 { + compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart"; + reg = <0x20064000 0x100>; + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clock-frequency = <24000000>; + clocks = <&cru SCLK_UART1>, <&cru PCLK_UART1>; + clock-names = "baudclk", "apb_pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&uart1_xfer>; + status = "disabled"; + }; + + uart2: serial at 20068000 { + compatible = "rockchip,rk3036-uart", "snps,dw-apb-uart"; + reg = <0x20068000 0x100>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; + reg-shift = <2>; + reg-io-width = <4>; + clock-frequency = <24000000>; + clocks = <&cru SCLK_UART2>, <&cru PCLK_UART2>; + clock-names = "baudclk", "apb_pclk"; + pinctrl-names = "default"; + pinctrl-0 = <&uart2_xfer>; + status = "disabled"; + }; + + usb_otg: usb at 10180000 { + compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb", + "snps,dwc2"; + reg = <0x10180000 0x40000>; + interrupts = <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru HCLK_OTG0>; + clock-names = "otg"; + dr_mode = "otg"; + g-np-tx-fifo-size = <16>; + g-rx-fifo-size = <275>; + g-tx-fifo-size = <256 128 128 64 64 32>; + g-use-dma; + status = "disabled"; + }; + + usb_host: usb at 101c0000 { + compatible = "rockchip,rk3288-usb", "rockchip,rk3066-usb", + "snps,dwc2"; + reg = <0x101c0000 0x40000>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru HCLK_OTG1>; + clock-names = "otg"; + dr_mode = "host"; + status = "disabled"; + }; + + pinctrl: pinctrl { + compatible = "rockchip,rk3036-pinctrl"; + rockchip,grf = <&grf>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + gpio0: gpio0 at 2007c000 { + compatible = "rockchip,gpio-bank"; + reg = <0x2007c000 0x100>; + interrupts = <GIC_SPI 36 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru PCLK_GPIO0>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio1: gpio1 at 20080000 { + compatible = "rockchip,gpio-bank"; + reg = <0x20080000 0x100>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru PCLK_GPIO1>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + gpio2: gpio2 at 20084000 { + compatible = "rockchip,gpio-bank"; + reg = <0x20084000 0x100>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; + clocks = <&cru PCLK_GPIO2>; + + gpio-controller; + #gpio-cells = <2>; + + interrupt-controller; + #interrupt-cells = <2>; + }; + + pcfg_pull_up: pcfg-pull-up { + bias-pull-up; + }; + + pcfg_pull_down: pcfg-pull-down { + bias-pull-down; + }; + + pcfg_pull_none: pcfg-pull-none { + bias-disable; + }; + + pwm0 { + pwm0_pin: pwm0-pin { + rockchip,pins = <0 0 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + pwm1 { + pwm1_pin: pwm1-pin { + rockchip,pins = <0 1 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + pwm2 { + pwm2_pin: pwm2-pin { + rockchip,pins = <0 1 2 &pcfg_pull_none>; + }; + }; + + pwm3 { + pwm3_pin: pwm3-pin { + rockchip,pins = <0 27 1 &pcfg_pull_none>; + }; + }; + + emmc { + /* + * We run eMMC at max speed; bump up drive strength. + * We also have external pulls, so disable the internal ones. + */ + emmc_clk: emmc-clk { + rockchip,pins = <2 4 RK_FUNC_2 &pcfg_pull_none>; + }; + + emmc_cmd: emmc-cmd { + rockchip,pins = <2 1 RK_FUNC_2 &pcfg_pull_none>; + }; + + emmc_bus8: emmc-bus8 { + rockchip,pins = <1 24 RK_FUNC_2 &pcfg_pull_none>, + <1 25 RK_FUNC_2 &pcfg_pull_none>, + <1 26 RK_FUNC_2 &pcfg_pull_none>, + <1 27 RK_FUNC_2 &pcfg_pull_none>, + <1 28 RK_FUNC_2 &pcfg_pull_none>, + <1 29 RK_FUNC_2 &pcfg_pull_none>, + <1 30 RK_FUNC_2 &pcfg_pull_none>, + <1 31 RK_FUNC_2 &pcfg_pull_none>; + }; + }; + + i2c0 { + i2c0_xfer: i2c0-xfer { + rockchip,pins = <0 0 RK_FUNC_1 &pcfg_pull_none>, + <0 1 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + i2c1 { + i2c1_xfer: i2c1-xfer { + rockchip,pins = <0 2 RK_FUNC_1 &pcfg_pull_none>, + <0 3 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + i2c2 { + i2c2_xfer: i2c2-xfer { + rockchip,pins = <2 20 RK_FUNC_1 &pcfg_pull_none>, + <2 21 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + i2s { + i2s_bus: i2s-bus { + rockchip,pins = <1 0 RK_FUNC_1 &pcfg_pull_none>, + <1 1 RK_FUNC_1 &pcfg_pull_none>, + <1 2 RK_FUNC_1 &pcfg_pull_none>, + <1 3 RK_FUNC_1 &pcfg_pull_none>, + <1 4 RK_FUNC_1 &pcfg_pull_none>, + <1 5 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + uart0 { + uart0_xfer: uart0-xfer { + rockchip,pins = <0 16 RK_FUNC_1 &pcfg_pull_up>, + <0 17 RK_FUNC_1 &pcfg_pull_none>; + }; + + uart0_cts: uart0-cts { + rockchip,pins = <0 18 RK_FUNC_1 &pcfg_pull_up>; + }; + + uart0_rts: uart0-rts { + rockchip,pins = <0 19 RK_FUNC_1 &pcfg_pull_none>; + }; + }; + + uart1 { + uart1_xfer: uart1-xfer { + rockchip,pins = <2 22 RK_FUNC_1 &pcfg_pull_none>, + <2 23 RK_FUNC_1 &pcfg_pull_none>; + }; + /* no rts / cts for uart1 */ + }; + + uart2 { + uart2_xfer: uart2-xfer { + rockchip,pins = <1 18 RK_FUNC_2 &pcfg_pull_none>, + <1 19 RK_FUNC_2 &pcfg_pull_none>; + }; + /* no rts / cts for uart2 */ + }; + }; +}; -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v5 6/8] ARM: rockchip: add support smp for rk3036 2015-10-26 4:25 [PATCH v5 0/8] Build and support rk3036 SoC platform Xing Zheng ` (3 preceding siblings ...) 2015-10-26 4:31 ` [PATCH v5 5/8] ARM: dts: rockchip: add core rk3036 dts Xing Zheng @ 2015-10-26 4:32 ` Xing Zheng 2015-10-26 4:33 ` [PATCH v5 7/8] ARM: dts: enable " Xing Zheng 2015-10-26 4:34 ` [PATCH v5 8/8] rockchip: make sure timer5 is enabled on rk3036 platforms Xing Zheng 6 siblings, 0 replies; 9+ messages in thread From: Xing Zheng @ 2015-10-26 4:32 UTC (permalink / raw) To: linux-arm-kernel From: Heiko Stuebner <heiko@sntech.de> The dual-core Cortex A7 rk3036 is a bit special in that it does not allow to control the actual powerdomain of the cpu cores, while the rest of the smp-bringup like reset control and entry address handling stays the same. Its bigger sibling, the quad-core rk3128 again allows powerdomain control. So allow that case by introducing a separate smp-enable-method, that simply disables powerdomain handling in the common code. Signed-off-by: Heiko Stuebner <heiko@sntech.de> Tested-by: Xing Zheng <zhengxing@rock-chips.com> Signed-off-by: Xing Zheng <zhengxing@rock-chips.com> --- Changes in v5: None Documentation/devicetree/bindings/arm/cpus.txt | 1 + arch/arm/mach-rockchip/platsmp.c | 45 +++++++++++++++++------- 2 files changed, 34 insertions(+), 12 deletions(-) diff --git a/Documentation/devicetree/bindings/arm/cpus.txt b/Documentation/devicetree/bindings/arm/cpus.txt index 91e6e5c..261cc27 100644 --- a/Documentation/devicetree/bindings/arm/cpus.txt +++ b/Documentation/devicetree/bindings/arm/cpus.txt @@ -198,6 +198,7 @@ nodes to be present and contain the properties described below. "qcom,gcc-msm8660" "qcom,kpss-acc-v1" "qcom,kpss-acc-v2" + "rockchip,rk3036-smp" "rockchip,rk3066-smp" "ste,dbx500-smp" diff --git a/arch/arm/mach-rockchip/platsmp.c b/arch/arm/mach-rockchip/platsmp.c index 3e7a4b7..5c138f9 100644 --- a/arch/arm/mach-rockchip/platsmp.c +++ b/arch/arm/mach-rockchip/platsmp.c @@ -42,6 +42,7 @@ static int ncores; #define PMU_PWRDN_SCU 4 static struct regmap *pmu; +static int has_pmu = true; static int pmu_power_domain_is_on(int pd) { @@ -89,20 +90,23 @@ static int pmu_set_power_domain(int pd, bool on) if (!IS_ERR(rstc) && !on) reset_control_assert(rstc); - ret = regmap_update_bits(pmu, PMU_PWRDN_CON, BIT(pd), val); - if (ret < 0) { - pr_err("%s: could not update power domain\n", __func__); - return ret; - } - - ret = -1; - while (ret != on) { - ret = pmu_power_domain_is_on(pd); + if (has_pmu) { + ret = regmap_update_bits(pmu, PMU_PWRDN_CON, BIT(pd), val); if (ret < 0) { - pr_err("%s: could not read power domain state\n", + pr_err("%s: could not update power domain\n", __func__); return ret; } + + ret = -1; + while (ret != on) { + ret = pmu_power_domain_is_on(pd); + if (ret < 0) { + pr_err("%s: could not read power domain state\n", + __func__); + return ret; + } + } } if (!IS_ERR(rstc)) { @@ -122,7 +126,7 @@ static int rockchip_boot_secondary(unsigned int cpu, struct task_struct *idle) { int ret; - if (!sram_base_addr || !pmu) { + if (!sram_base_addr || (has_pmu && !pmu)) { pr_err("%s: sram or pmu missing for cpu boot\n", __func__); return -ENXIO; } @@ -275,7 +279,7 @@ static void __init rockchip_smp_prepare_cpus(unsigned int max_cpus) return; } - if (rockchip_smp_prepare_pmu()) + if (has_pmu && rockchip_smp_prepare_pmu()) return; if (read_cpuid_part() == ARM_CPU_PART_CORTEX_A9) { @@ -318,6 +322,13 @@ static void __init rockchip_smp_prepare_cpus(unsigned int max_cpus) pmu_set_power_domain(0 + i, false); } +static void __init rk3036_smp_prepare_cpus(unsigned int max_cpus) +{ + has_pmu = false; + + rockchip_smp_prepare_cpus(max_cpus); +} + #ifdef CONFIG_HOTPLUG_CPU static int rockchip_cpu_kill(unsigned int cpu) { @@ -340,6 +351,15 @@ static void rockchip_cpu_die(unsigned int cpu) } #endif +static struct smp_operations rk3036_smp_ops __initdata = { + .smp_prepare_cpus = rk3036_smp_prepare_cpus, + .smp_boot_secondary = rockchip_boot_secondary, +#ifdef CONFIG_HOTPLUG_CPU + .cpu_kill = rockchip_cpu_kill, + .cpu_die = rockchip_cpu_die, +#endif +}; + static struct smp_operations rockchip_smp_ops __initdata = { .smp_prepare_cpus = rockchip_smp_prepare_cpus, .smp_boot_secondary = rockchip_boot_secondary, @@ -349,4 +369,5 @@ static struct smp_operations rockchip_smp_ops __initdata = { #endif }; +CPU_METHOD_OF_DECLARE(rk3036_smp, "rockchip,rk3036-smp", &rk3036_smp_ops); CPU_METHOD_OF_DECLARE(rk3066_smp, "rockchip,rk3066-smp", &rockchip_smp_ops); -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v5 7/8] ARM: dts: enable smp for rk3036 2015-10-26 4:25 [PATCH v5 0/8] Build and support rk3036 SoC platform Xing Zheng ` (4 preceding siblings ...) 2015-10-26 4:32 ` [PATCH v5 6/8] ARM: rockchip: add support smp for rk3036 Xing Zheng @ 2015-10-26 4:33 ` Xing Zheng 2015-10-26 4:34 ` [PATCH v5 8/8] rockchip: make sure timer5 is enabled on rk3036 platforms Xing Zheng 6 siblings, 0 replies; 9+ messages in thread From: Xing Zheng @ 2015-10-26 4:33 UTC (permalink / raw) To: linux-arm-kernel Enable smp for rk3036, and add the smp sram name for adapting. Signed-off-by: Xing Zheng <zhengxing@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> --- Changes in v5: None arch/arm/boot/dts/rk3036.dtsi | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/arch/arm/boot/dts/rk3036.dtsi b/arch/arm/boot/dts/rk3036.dtsi index 8f3a069..61352be 100644 --- a/arch/arm/boot/dts/rk3036.dtsi +++ b/arch/arm/boot/dts/rk3036.dtsi @@ -72,6 +72,7 @@ cpus { #address-cells = <1>; #size-cells = <0>; + enable-method = "rockchip,rk3036-smp"; cpu0: cpu at f00 { device_type = "cpu"; @@ -146,6 +147,10 @@ #address-cells = <1>; #size-cells = <1>; ranges = <0 0x10080000 0x2000>; + smp-sram at 0 { + compatible = "rockchip,rk3066-smp-sram"; + reg = <0x00 0x10>; + }; }; cru: clock-controller at 20000000 { -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 9+ messages in thread
* [PATCH v5 8/8] rockchip: make sure timer5 is enabled on rk3036 platforms 2015-10-26 4:25 [PATCH v5 0/8] Build and support rk3036 SoC platform Xing Zheng ` (5 preceding siblings ...) 2015-10-26 4:33 ` [PATCH v5 7/8] ARM: dts: enable " Xing Zheng @ 2015-10-26 4:34 ` Xing Zheng 6 siblings, 0 replies; 9+ messages in thread From: Xing Zheng @ 2015-10-26 4:34 UTC (permalink / raw) To: linux-arm-kernel The timer5 supplies the architected timer and thus as has to run when the system clocksource and clockevents drivers are registered. --- Changes in v5: Signed-off-by: Xing Zheng <zhengxing@rock-chips.com> Reviewed-by: Heiko Stuebner <heiko@sntech.de> arch/arm/mach-rockchip/rockchip.c | 44 +++++++++++++++++++++++-------------- 1 file changed, 27 insertions(+), 17 deletions(-) diff --git a/arch/arm/mach-rockchip/rockchip.c b/arch/arm/mach-rockchip/rockchip.c index 251c7b9..608b31c 100644 --- a/arch/arm/mach-rockchip/rockchip.c +++ b/arch/arm/mach-rockchip/rockchip.c @@ -29,31 +29,38 @@ #include "core.h" #include "pm.h" +#define RK3036_TIMER_PHYS 0x20044000 + #define RK3288_GRF_SOC_CON0 0x244 #define RK3288_TIMER6_7_PHYS 0xff810000 +static void rockchip_init_arch_timer_supply(resource_size_t phys, int offs) +{ + void __iomem *reg_base = ioremap(phys, SZ_16K); + + /* + * Most/all uboot versions for Rockchip SoCs don't enable + * timer which is needed for the architected timer to work. + * So make sure it is running during early boot. + */ + if (reg_base) { + writel(0, reg_base + offs + 0x10); + writel(0xffffffff, reg_base + offs); + writel(0xffffffff, reg_base + offs + 0x04); + writel(1, reg_base + offs + 0x10); + dsb(); + iounmap(reg_base); + } else { + pr_err("rockchip: could not map timer registers\n"); + } +} + static void __init rockchip_timer_init(void) { if (of_machine_is_compatible("rockchip,rk3288")) { struct regmap *grf; - void __iomem *reg_base; - /* - * Most/all uboot versions for rk3288 don't enable timer7 - * which is needed for the architected timer to work. - * So make sure it is running during early boot. - */ - reg_base = ioremap(RK3288_TIMER6_7_PHYS, SZ_16K); - if (reg_base) { - writel(0, reg_base + 0x30); - writel(0xffffffff, reg_base + 0x20); - writel(0xffffffff, reg_base + 0x24); - writel(1, reg_base + 0x30); - dsb(); - iounmap(reg_base); - } else { - pr_err("rockchip: could not map timer7 registers\n"); - } + rockchip_init_arch_timer_supply(RK3288_TIMER6_7_PHYS, 0x20); /* * Disable auto jtag/sdmmc switching that causes issues @@ -64,6 +71,8 @@ static void __init rockchip_timer_init(void) regmap_write(grf, RK3288_GRF_SOC_CON0, 0x10000000); else pr_err("rockchip: could not get grf syscon\n"); + } else if (of_machine_is_compatible("rockchip,rk3036")) { + rockchip_init_arch_timer_supply(RK3036_TIMER_PHYS, 0xa0); } of_clk_init(NULL); @@ -79,6 +88,7 @@ static void __init rockchip_dt_init(void) static const char * const rockchip_board_dt_compat[] = { "rockchip,rk2928", + "rockchip,rk3036", "rockchip,rk3066a", "rockchip,rk3066b", "rockchip,rk3188", -- 1.7.9.5 ^ permalink raw reply related [flat|nested] 9+ messages in thread
end of thread, other threads:[~2015-10-28 7:53 UTC | newest] Thread overview: 9+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2015-10-26 4:25 [PATCH v5 0/8] Build and support rk3036 SoC platform Xing Zheng 2015-10-26 4:25 ` [PATCH v5 1/8] dt-bindings: add documentation of rk3036 clock controller Xing Zheng 2015-10-26 4:25 ` [PATCH v5 3/8] clk: rockchip: add clock controller for rk3036 Xing Zheng 2015-10-28 7:53 ` Heiko Stuebner 2015-10-26 4:25 ` [PATCH v5 4/8] clk: rockchip: add new pll-type for rk3036 and similar socs Xing Zheng 2015-10-26 4:31 ` [PATCH v5 5/8] ARM: dts: rockchip: add core rk3036 dts Xing Zheng 2015-10-26 4:32 ` [PATCH v5 6/8] ARM: rockchip: add support smp for rk3036 Xing Zheng 2015-10-26 4:33 ` [PATCH v5 7/8] ARM: dts: enable " Xing Zheng 2015-10-26 4:34 ` [PATCH v5 8/8] rockchip: make sure timer5 is enabled on rk3036 platforms Xing Zheng
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).