[RFC/PATCH 0/7] ARCH: shmobile: defconfig consolidation

[laurent.pinchart@ideasonboard.com (Laurent Pinchart)]

On Friday 05 April 2013 09:30:27 Simon Horman wrote:
> On Thu, Apr 04, 2013 at 01:20:44PM +0200, Laurent Pinchart wrote:
> > On Thursday 04 April 2013 12:29:46 Simon Horman wrote:
> > > Hi,
> > > 
> > > this is a first pass at consolidating the defconfigs of shmobile.
> > > 
> > > It covers the mackerel, amradillo800eva and kzm9d boards which meet
> > > the following criteria:
> > > 
> > > * Have the same base memory address (0x40000000).
> > 
> > Do you know if there's any work being done on getting rid of the base
> > memory address as a kernel config option ? It seriously hinders cross-SoC
> > kernel testing.
> 
> As I understand things the main limitation is uImage which uses
> the base memory address. There is some talk of creating uImages
> at install time rather than build time. Which I believe would
> remove most if not all the problem. However, its entirely unclear
> to me what such an install process would look like. A new build target?
> In tree script? Out of tree script? It seems very undefined to me.
> 
> Another, arguably better though not backwards compatible, option
> is to boot using zImage (or even just Image) which do not rely
> on the base address.

Don't we also need to get rid of CONFIG_MEMORY_START ? It's used in headsmp.S 
and headsmp-scu.S (through PLAT_PHYS_OFFSET).

> I'm not aware of any other work or discussion in this area although
> it would not surprise me if there was some.
>
> > > * Work with RUNTIME_PM, it is desirable to have that a common defconfig
> > > * Are booted via DT, enabling the command line to be supplied in the
> > > dts.
> > > 
> > >   This is important to allow serial console and early printk settings,
> > >   which vary wildly between boards, to be supplied.
> > > 
> > > * Boards I have to test.
> > > 
> > >   This didn't eliminate any candidates that met the above criteria.
> > > 
> > > I believe it should also be possible to add support for the APE6EVM
> > > board to the consolidated defconfig once problems with RUNTIME_PM
> > > have been isolated and resolved. I have send an email about this
> > > in a separate thread "APE6EVM and Runtime PM".
> > > 
> > > I believe it may be possible to add support for the lager board
> > > to the consolidated defconfig once I am able to bring that board up,
> > > which should be rather soon. The lager board does not currently
> > > have a defconfig.
> > > 
> > > Morimoto-san, I suspect it may be possible to add support for the
> > > bockw board to the consolidated defconfig if its boot loader supports
> > > booting using a zImage. In this case even though the base memory address
> > > is not the same as the boards above it should be possible to specify
> > > the base address from the boot loader. As I do not have a bockw board
> > > I am wondering if you could investigate this.
> > > 
> > > Simon Horman (7):
> > >   ARM: shmobile: prune defconfig
> > >   ARM: shmobile: make defconfig canonical
> > >   ARM: shmobile: Add kzm9d to consolidated defconfig
> > >   ARM: shmobile: Add mackerel to consolidated defconfig
> > >   ARM: shmobile: defconfig: Remove armadillo800eva defconfig
> > >   ARM: shmobile: defconfig: Remove kzm9d defconfig
> > >   ARM: shmobile: defconfig: Remove mackerel defconfig
> > >  
> > >  arch/arm/configs/armadillo800eva_defconfig |  153 ---------------------
> > >  arch/arm/configs/kzm9d_defconfig           |   88 ----------------
> > >  arch/arm/configs/mackerel_defconfig        |  156 ---------------------
> > >  arch/arm/configs/shmobile_defconfig        |   51 +++++----
> > >  4 files changed, 28 insertions(+), 420 deletions(-)
> > >  delete mode 100644 arch/arm/configs/armadillo800eva_defconfig
> > >  delete mode 100644 arch/arm/configs/kzm9d_defconfig
> > >  delete mode 100644 arch/arm/configs/mackerel_defconfig

-- 
Regards,

Laurent Pinchart