[PATCH V2 1/8] SPEAr13xx: Set dt field entry <stmmac, phy-addr> for phy probe

[PATCH V2 1/8] SPEAr13xx: Set dt field entry <stmmac, phy-addr> for phy probe

[Mohit Kumar]

DT field name for the phy address changed since kernel 3.10. Set the
snps,phy-addr to 0xffffffff so that the driver probes for the phy.

Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Pratyush Anand <pratyush.anand@st.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: spear-devel at list.st.com
Cc: linux-arm-kernel at lists.infradead.org
Cc: devicetree at vger.kernel.org
---
 arch/arm/boot/dts/spear13xx.dtsi |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/spear13xx.dtsi b/arch/arm/boot/dts/spear13xx.dtsi
index 4382547..3518803 100644
--- a/arch/arm/boot/dts/spear13xx.dtsi
+++ b/arch/arm/boot/dts/spear13xx.dtsi
@@ -155,6 +155,7 @@
 
 		gmac0: eth at e2000000 {
 			compatible = "st,spear600-gmac";
+			snps,phy-addr = <0xffffffff>;
 			reg = <0xe2000000 0x8000>;
 			interrupts = <0 33 0x4
 				      0 34 0x4>;
-- 
1.7.0.1

[PATCH V2 2/8] SPEAr13xx: defconfig: Update

[Mohit Kumar]

Enable EABI, OEABI, VFP and NFS configs in default configuration file for
SPEAr13xx.

Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Mohit Kumar <mohit.kumar@st.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: spear-devel at list.st.com
Cc: linux-arm-kernel at lists.infradead.org
---
 arch/arm/configs/spear13xx_defconfig |   14 ++++++++++++++
 1 files changed, 14 insertions(+), 0 deletions(-)

diff --git a/arch/arm/configs/spear13xx_defconfig b/arch/arm/configs/spear13xx_defconfig
index 82eaa55..0cf87d0 100644
--- a/arch/arm/configs/spear13xx_defconfig
+++ b/arch/arm/configs/spear13xx_defconfig
@@ -14,10 +14,19 @@ CONFIG_MACH_SPEAR1340=y
 CONFIG_SMP=y
 # CONFIG_SMP_ON_UP is not set
 # CONFIG_ARM_CPU_TOPOLOGY is not set
+CONFIG_AEABI=y
+CONFIG_OABI_COMPAT=y
 CONFIG_ARM_APPENDED_DTB=y
 CONFIG_ARM_ATAG_DTB_COMPAT=y
+CONFIG_VFP=y
 CONFIG_BINFMT_MISC=y
 CONFIG_NET=y
+CONFIG_UNIX=y
+CONFIG_INET=y
+CONFIG_IP_PNP=y
+CONFIG_IP_PNP_DHCP=y
+CONFIG_IP_PNP_BOOTP=y
+CONFIG_NET_IPIP=y
 CONFIG_UEVENT_HELPER_PATH="/sbin/hotplug"
 CONFIG_MTD=y
 CONFIG_MTD_OF_PARTS=y
@@ -27,6 +36,7 @@ CONFIG_MTD_NAND=y
 CONFIG_MTD_NAND_FSMC=y
 CONFIG_BLK_DEV_RAM=y
 CONFIG_BLK_DEV_RAM_SIZE=16384
+CONFIG_BLK_DEV_SD=y
 CONFIG_ATA=y
 # CONFIG_SATA_PMP is not set
 CONFIG_SATA_AHCI_PLATFORM=y
@@ -66,6 +76,7 @@ CONFIG_USB=y
 # CONFIG_USB_DEVICE_CLASS is not set
 CONFIG_USB_EHCI_HCD=y
 CONFIG_USB_OHCI_HCD=y
+CONFIG_USB_STORAGE=y
 CONFIG_MMC=y
 CONFIG_MMC_SDHCI=y
 CONFIG_MMC_SDHCI_SPEAR=y
@@ -79,11 +90,14 @@ CONFIG_EXT2_FS_SECURITY=y
 CONFIG_EXT3_FS=y
 CONFIG_EXT3_FS_SECURITY=y
 CONFIG_AUTOFS4_FS=m
+CONFIG_FUSE_FS=y
 CONFIG_MSDOS_FS=m
 CONFIG_VFAT_FS=m
 CONFIG_FAT_DEFAULT_IOCHARSET="ascii"
 CONFIG_TMPFS=y
 CONFIG_JFFS2_FS=y
+CONFIG_NFS_FS=y
+CONFIG_ROOT_NFS=y
 CONFIG_NLS_DEFAULT="utf8"
 CONFIG_NLS_CODEPAGE_437=y
 CONFIG_NLS_ASCII=m
-- 
1.7.0.1

[PATCH V2 3/8] ahci: Add a driver_data field to struct ahci_platform_data

[Mohit Kumar]

From: Pratyush Anand <pratyush.anand@st.com>

Platform functions passed to the driver may also need some private
data. Till, now following approaches have been taken to manage these
data:
-- SPEAr13xx platform keep it locally in the files defining platform
functions.
-- IMX has created a new ahci platform device as a child of
platform device created by DT and then attached this data as the
driver_data of ahci's dev->parent.

Adding a driver_data field helps in using the same platform driver as
that of created by DT.

Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: spear-devel at list.st.com
Cc: linux-arm-kernel at lists.infradead.org
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-ide at vger.kernel.org
Cc: devicetree at vger.kernel.org
Cc: Arnd Bergmann <arnd@arndb.de>
---
 include/linux/ahci_platform.h |    1 +
 1 files changed, 1 insertions(+), 0 deletions(-)

diff --git a/include/linux/ahci_platform.h b/include/linux/ahci_platform.h
index 73a2500..76d35e8 100644
--- a/include/linux/ahci_platform.h
+++ b/include/linux/ahci_platform.h
@@ -28,6 +28,7 @@ struct ahci_platform_data {
 	const struct ata_port_info *ata_port_info;
 	unsigned int force_port_map;
 	unsigned int mask_port_map;
+	void *driver_data;
 };
 
 #endif /* _AHCI_PLATFORM_H */
-- 
1.7.0.1

[PATCH V2 4/8] SPEAr13xx: Fixup: Move SPEAr1340 SATA platform code to system cfg driver

[Mohit Kumar]

From: Pratyush Anand <pratyush.anand@st.com>

ahci driver needs some platform specific functions which are called at
init, exit, suspend and resume conditions. Till now these functions were
present in a platform driver with a fixme notes. These functions
modifies only misc registers and not any phy register. Same misc
registers will also be modified in case of PCIe driver initialization.

Therefore, moving those code from mach-spear/spear1340.c to
mfd/spear13xx-cfg.c.

Same file can further be used to add PCIe system configuration part.

Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: spear-devel at list.st.com
Cc: linux-arm-kernel at lists.infradead.org
Cc: Tejun Heo <tj@kernel.org>
Cc: linux-ide at vger.kernel.org
Cc: devicetree at vger.kernel.org
Cc: Arnd Bergmann <arnd@arndb.de>
---
 arch/arm/boot/dts/spear13xx.dtsi |    9 ++
 arch/arm/mach-spear/Kconfig      |    1 +
 arch/arm/mach-spear/spear1340.c  |  127 +--------------------
 drivers/mfd/Makefile             |    1 +
 drivers/mfd/spear13xx-cfg.c      |  239 ++++++++++++++++++++++++++++++++++++++
 5 files changed, 251 insertions(+), 126 deletions(-)
 create mode 100644 drivers/mfd/spear13xx-cfg.c

diff --git a/arch/arm/boot/dts/spear13xx.dtsi b/arch/arm/boot/dts/spear13xx.dtsi
index 3518803..2b4e58e 100644
--- a/arch/arm/boot/dts/spear13xx.dtsi
+++ b/arch/arm/boot/dts/spear13xx.dtsi
@@ -78,6 +78,10 @@
 		status = "disabled";
 	};
 
+	cfg {
+		compatible = "st,spear13xx-cfg";
+	};
+
 	ahb {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -221,6 +225,11 @@
 				  0xd8000000 0xd8000000 0x01000000
 				  0xe0000000 0xe0000000 0x10000000>;
 
+			misc: misc at e0700000 {
+				compatible = "st,spear13xx-misc", "syscon";
+				reg = <0xe0700000 0x1000>;
+			};
+
 			gpio0: gpio at e0600000 {
 				compatible = "arm,pl061", "arm,primecell";
 				reg = <0xe0600000 0x1000>;
diff --git a/arch/arm/mach-spear/Kconfig b/arch/arm/mach-spear/Kconfig
index ac1710e..dedcafb 100644
--- a/arch/arm/mach-spear/Kconfig
+++ b/arch/arm/mach-spear/Kconfig
@@ -26,6 +26,7 @@ config ARCH_SPEAR13XX
 	select MIGHT_HAVE_CACHE_L2X0
 	select PINCTRL
 	select USE_OF
+	select MFD_SYSCON
 	help
 	  Supports for ARM's SPEAR13XX family
 
diff --git a/arch/arm/mach-spear/spear1340.c b/arch/arm/mach-spear/spear1340.c
index 3fb6834..8e27093 100644
--- a/arch/arm/mach-spear/spear1340.c
+++ b/arch/arm/mach-spear/spear1340.c
@@ -11,138 +11,13 @@
  * warranty of any kind, whether express or implied.
  */
 
-#define pr_fmt(fmt) "SPEAr1340: " fmt
-
-#include <linux/ahci_platform.h>
-#include <linux/amba/serial.h>
-#include <linux/delay.h>
 #include <linux/of_platform.h>
 #include <asm/mach/arch.h>
 #include "generic.h"
-#include <mach/spear.h>
-
-/* FIXME: Move SATA PHY code into a standalone driver */
-
-/* Base addresses */
-#define SPEAR1340_SATA_BASE			UL(0xB1000000)
-
-/* Power Management Registers */
-#define SPEAR1340_PCM_CFG			(VA_MISC_BASE + 0x100)
-#define SPEAR1340_PCM_WKUP_CFG			(VA_MISC_BASE + 0x104)
-#define SPEAR1340_SWITCH_CTR			(VA_MISC_BASE + 0x108)
-
-#define SPEAR1340_PERIP1_SW_RST			(VA_MISC_BASE + 0x318)
-#define SPEAR1340_PERIP2_SW_RST			(VA_MISC_BASE + 0x31C)
-#define SPEAR1340_PERIP3_SW_RST			(VA_MISC_BASE + 0x320)
-
-/* PCIE - SATA configuration registers */
-#define SPEAR1340_PCIE_SATA_CFG			(VA_MISC_BASE + 0x424)
-	/* PCIE CFG MASks */
-	#define SPEAR1340_PCIE_CFG_DEVICE_PRESENT	(1 << 11)
-	#define SPEAR1340_PCIE_CFG_POWERUP_RESET	(1 << 10)
-	#define SPEAR1340_PCIE_CFG_CORE_CLK_EN		(1 << 9)
-	#define SPEAR1340_PCIE_CFG_AUX_CLK_EN		(1 << 8)
-	#define SPEAR1340_SATA_CFG_TX_CLK_EN		(1 << 4)
-	#define SPEAR1340_SATA_CFG_RX_CLK_EN		(1 << 3)
-	#define SPEAR1340_SATA_CFG_POWERUP_RESET	(1 << 2)
-	#define SPEAR1340_SATA_CFG_PM_CLK_EN		(1 << 1)
-	#define SPEAR1340_PCIE_SATA_SEL_PCIE		(0)
-	#define SPEAR1340_PCIE_SATA_SEL_SATA		(1)
-	#define SPEAR1340_SATA_PCIE_CFG_MASK		0xF1F
-	#define SPEAR1340_PCIE_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_PCIE | \
-			SPEAR1340_PCIE_CFG_AUX_CLK_EN | \
-			SPEAR1340_PCIE_CFG_CORE_CLK_EN | \
-			SPEAR1340_PCIE_CFG_POWERUP_RESET | \
-			SPEAR1340_PCIE_CFG_DEVICE_PRESENT)
-	#define SPEAR1340_SATA_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_SATA | \
-			SPEAR1340_SATA_CFG_PM_CLK_EN | \
-			SPEAR1340_SATA_CFG_POWERUP_RESET | \
-			SPEAR1340_SATA_CFG_RX_CLK_EN | \
-			SPEAR1340_SATA_CFG_TX_CLK_EN)
-
-#define SPEAR1340_PCIE_MIPHY_CFG		(VA_MISC_BASE + 0x428)
-	#define SPEAR1340_MIPHY_OSC_BYPASS_EXT		(1 << 31)
-	#define SPEAR1340_MIPHY_CLK_REF_DIV2		(1 << 27)
-	#define SPEAR1340_MIPHY_CLK_REF_DIV4		(2 << 27)
-	#define SPEAR1340_MIPHY_CLK_REF_DIV8		(3 << 27)
-	#define SPEAR1340_MIPHY_PLL_RATIO_TOP(x)	(x << 0)
-	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA \
-			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
-			SPEAR1340_MIPHY_CLK_REF_DIV2 | \
-			SPEAR1340_MIPHY_PLL_RATIO_TOP(60))
-	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK \
-			(SPEAR1340_MIPHY_PLL_RATIO_TOP(120))
-	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_PCIE \
-			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
-			SPEAR1340_MIPHY_PLL_RATIO_TOP(25))
-
-/* SATA device registration */
-static int sata_miphy_init(struct device *dev, void __iomem *addr)
-{
-	writel(SPEAR1340_SATA_CFG_VAL, SPEAR1340_PCIE_SATA_CFG);
-	writel(SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK,
-			SPEAR1340_PCIE_MIPHY_CFG);
-	/* Switch on sata power domain */
-	writel((readl(SPEAR1340_PCM_CFG) | (0x800)), SPEAR1340_PCM_CFG);
-	msleep(20);
-	/* Disable PCIE SATA Controller reset */
-	writel((readl(SPEAR1340_PERIP1_SW_RST) & (~0x1000)),
-			SPEAR1340_PERIP1_SW_RST);
-	msleep(20);
-
-	return 0;
-}
-
-void sata_miphy_exit(struct device *dev)
-{
-	writel(0, SPEAR1340_PCIE_SATA_CFG);
-	writel(0, SPEAR1340_PCIE_MIPHY_CFG);
-
-	/* Enable PCIE SATA Controller reset */
-	writel((readl(SPEAR1340_PERIP1_SW_RST) | (0x1000)),
-			SPEAR1340_PERIP1_SW_RST);
-	msleep(20);
-	/* Switch off sata power domain */
-	writel((readl(SPEAR1340_PCM_CFG) & (~0x800)), SPEAR1340_PCM_CFG);
-	msleep(20);
-}
-
-int sata_suspend(struct device *dev)
-{
-	if (dev->power.power_state.event == PM_EVENT_FREEZE)
-		return 0;
-
-	sata_miphy_exit(dev);
-
-	return 0;
-}
-
-int sata_resume(struct device *dev)
-{
-	if (dev->power.power_state.event == PM_EVENT_THAW)
-		return 0;
-
-	return sata_miphy_init(dev, NULL);
-}
-
-static struct ahci_platform_data sata_pdata = {
-	.init = sata_miphy_init,
-	.exit = sata_miphy_exit,
-	.suspend = sata_suspend,
-	.resume = sata_resume,
-};
-
-/* Add SPEAr1340 auxdata to pass platform data */
-static struct of_dev_auxdata spear1340_auxdata_lookup[] __initdata = {
-	OF_DEV_AUXDATA("snps,spear-ahci", SPEAR1340_SATA_BASE, NULL,
-			&sata_pdata),
-	{}
-};
 
 static void __init spear1340_dt_init(void)
 {
-	of_platform_populate(NULL, of_default_bus_match_table,
-			spear1340_auxdata_lookup, NULL);
+	of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL);
 }
 
 static const char * const spear1340_dt_board_compat[] = {
diff --git a/drivers/mfd/Makefile b/drivers/mfd/Makefile
index 8a28dc9..9e5565b 100644
--- a/drivers/mfd/Makefile
+++ b/drivers/mfd/Makefile
@@ -164,3 +164,4 @@ obj-$(CONFIG_MFD_RETU)		+= retu-mfd.o
 obj-$(CONFIG_MFD_AS3711)	+= as3711.o
 obj-$(CONFIG_MFD_AS3722)	+= as3722.o
 obj-$(CONFIG_MFD_STW481X)	+= stw481x.o
+obj-$(CONFIG_ARCH_SPEAR13XX)	+= spear13xx-cfg.o
diff --git a/drivers/mfd/spear13xx-cfg.c b/drivers/mfd/spear13xx-cfg.c
new file mode 100644
index 0000000..1cf5785
--- /dev/null
+++ b/drivers/mfd/spear13xx-cfg.c
@@ -0,0 +1,239 @@
+/*
+ * ST SPEAr13xx System Configuration driver
+ *
+ * Copyright (C) 2010-2014 ST Microelectronics
+ * Pratyush Anand <pratyush.anand@st.com>
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+#include <linux/ahci_platform.h>
+#include <linux/delay.h>
+#include <linux/dma-mapping.h>
+#include <linux/kernel.h>
+#include <linux/mfd/syscon.h>
+#include <linux/module.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/regmap.h>
+
+/* SPEAr1340 Registers */
+/* Power Management Registers */
+#define SPEAR1340_PCM_CFG			0x100
+	#define SPEAR1340_PCM_CFG_SATA_POWER_EN	0x800
+#define SPEAR1340_PCM_WKUP_CFG			0x104
+#define SPEAR1340_SWITCH_CTR			0x108
+
+#define SPEAR1340_PERIP1_SW_RST			0x318
+	#define SPEAR1340_PERIP1_SW_RST_SATA	0x1000
+#define SPEAR1340_PERIP2_SW_RST			0x31C
+#define SPEAR1340_PERIP3_SW_RST			0x320
+
+/* PCIE - SATA configuration registers */
+#define SPEAR1340_PCIE_SATA_CFG			0x424
+	/* PCIE CFG MASks */
+	#define SPEAR1340_PCIE_CFG_DEVICE_PRESENT	(1 << 11)
+	#define SPEAR1340_PCIE_CFG_POWERUP_RESET	(1 << 10)
+	#define SPEAR1340_PCIE_CFG_CORE_CLK_EN		(1 << 9)
+	#define SPEAR1340_PCIE_CFG_AUX_CLK_EN		(1 << 8)
+	#define SPEAR1340_SATA_CFG_TX_CLK_EN		(1 << 4)
+	#define SPEAR1340_SATA_CFG_RX_CLK_EN		(1 << 3)
+	#define SPEAR1340_SATA_CFG_POWERUP_RESET	(1 << 2)
+	#define SPEAR1340_SATA_CFG_PM_CLK_EN		(1 << 1)
+	#define SPEAR1340_PCIE_SATA_SEL_PCIE		(0)
+	#define SPEAR1340_PCIE_SATA_SEL_SATA		(1)
+	#define SPEAR1340_PCIE_SATA_CFG_MASK		0xF1F
+	#define SPEAR1340_PCIE_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_PCIE | \
+			SPEAR1340_PCIE_CFG_AUX_CLK_EN | \
+			SPEAR1340_PCIE_CFG_CORE_CLK_EN | \
+			SPEAR1340_PCIE_CFG_POWERUP_RESET | \
+			SPEAR1340_PCIE_CFG_DEVICE_PRESENT)
+	#define SPEAR1340_SATA_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_SATA | \
+			SPEAR1340_SATA_CFG_PM_CLK_EN | \
+			SPEAR1340_SATA_CFG_POWERUP_RESET | \
+			SPEAR1340_SATA_CFG_RX_CLK_EN | \
+			SPEAR1340_SATA_CFG_TX_CLK_EN)
+
+#define SPEAR1340_PCIE_MIPHY_CFG		0x428
+	#define SPEAR1340_MIPHY_OSC_BYPASS_EXT		(1 << 31)
+	#define SPEAR1340_MIPHY_CLK_REF_DIV2		(1 << 27)
+	#define SPEAR1340_MIPHY_CLK_REF_DIV4		(2 << 27)
+	#define SPEAR1340_MIPHY_CLK_REF_DIV8		(3 << 27)
+	#define SPEAR1340_MIPHY_PLL_RATIO_TOP(x)	(x << 0)
+	#define SPEAR1340_PCIE_MIPHY_CFG_MASK		0xF80000FF
+	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA \
+			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
+			SPEAR1340_MIPHY_CLK_REF_DIV2 | \
+			SPEAR1340_MIPHY_PLL_RATIO_TOP(60))
+	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK \
+			(SPEAR1340_MIPHY_PLL_RATIO_TOP(120))
+	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_PCIE \
+			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
+			SPEAR1340_MIPHY_PLL_RATIO_TOP(25))
+
+struct spear13xx_cfg_priv {
+	struct regmap		*misc;
+};
+
+/* SATA device registration */
+static void spear1340_sata_miphy_init(struct spear13xx_cfg_priv *cfgpriv)
+{
+	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCIE_SATA_CFG,
+			SPEAR1340_PCIE_SATA_CFG_MASK, SPEAR1340_SATA_CFG_VAL);
+	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCIE_MIPHY_CFG,
+			SPEAR1340_PCIE_MIPHY_CFG_MASK,
+			SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK);
+	/* Switch on sata power domain */
+	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCM_CFG,
+			SPEAR1340_PCM_CFG_SATA_POWER_EN,
+			SPEAR1340_PCM_CFG_SATA_POWER_EN);
+	msleep(20);
+	/* Disable PCIE SATA Controller reset */
+	regmap_update_bits(cfgpriv->misc, SPEAR1340_PERIP1_SW_RST,
+			SPEAR1340_PERIP1_SW_RST_SATA, 0);
+	msleep(20);
+}
+
+static void spear1340_sata_miphy_exit(struct spear13xx_cfg_priv *cfgpriv)
+{
+	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCIE_SATA_CFG,
+			SPEAR1340_PCIE_SATA_CFG_MASK, 0);
+	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCIE_MIPHY_CFG,
+			SPEAR1340_PCIE_MIPHY_CFG_MASK, 0);
+
+	/* Enable PCIE SATA Controller reset */
+	regmap_update_bits(cfgpriv->misc, SPEAR1340_PERIP1_SW_RST,
+			SPEAR1340_PERIP1_SW_RST_SATA,
+			SPEAR1340_PERIP1_SW_RST_SATA);
+	msleep(20);
+	/* Switch off sata power domain */
+	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCM_CFG,
+			SPEAR1340_PCM_CFG_SATA_POWER_EN, 0);
+	msleep(20);
+}
+
+/* SATA device registration */
+static int sata_miphy_init(struct device *dev, void __iomem *addr)
+{
+	struct ahci_platform_data *ahci_pdata = dev_get_platdata(dev);
+	struct spear13xx_cfg_priv *cfgpriv = ahci_pdata->driver_data;
+
+	if (of_machine_is_compatible("st,spear1340"))
+		spear1340_sata_miphy_init(cfgpriv);
+	else
+		return -EINVAL;
+
+	return 0;
+}
+
+static void sata_miphy_exit(struct device *dev)
+{
+	struct ahci_platform_data *ahci_pdata = dev_get_platdata(dev);
+	struct spear13xx_cfg_priv *cfgpriv = ahci_pdata->driver_data;
+
+	if (of_machine_is_compatible("st,spear1340"))
+		spear1340_sata_miphy_exit(cfgpriv);
+}
+
+static int sata_suspend(struct device *dev)
+{
+	if (dev->power.power_state.event == PM_EVENT_FREEZE)
+		return 0;
+
+	sata_miphy_exit(dev);
+
+	return 0;
+}
+
+static int sata_resume(struct device *dev)
+{
+	if (dev->power.power_state.event == PM_EVENT_THAW)
+		return 0;
+
+	return sata_miphy_init(dev, NULL);
+}
+
+static struct ahci_platform_data sata_pdata = {
+	.init = sata_miphy_init,
+	.exit = sata_miphy_exit,
+	.suspend = sata_suspend,
+	.resume = sata_resume,
+};
+
+static const struct of_device_id spear13xx_cfg_of_match[] = {
+	{ .compatible = "st,spear13xx-cfg" },
+	{ },
+};
+MODULE_DEVICE_TABLE(of, spear13xx_cfg_of_match);
+
+static int __init spear13xx_cfg_probe(struct platform_device *pdev)
+{
+	struct device *dev = &pdev->dev;
+	struct ahci_platform_data *ahci_pdata = &sata_pdata;
+	struct spear13xx_cfg_priv *cfgpriv;
+	struct device_node *np_ahci;
+	struct platform_device *ahci_pdev;
+	int ret = 0;
+
+	cfgpriv = devm_kzalloc(dev, sizeof(*cfgpriv), GFP_KERNEL);
+	if (!cfgpriv) {
+		dev_err(dev, "can't alloc sata pcie private date memory\n");
+		return -ENOMEM;
+	}
+
+	cfgpriv->misc =
+		syscon_regmap_lookup_by_compatible("st,spear13xx-misc");
+	if (IS_ERR(cfgpriv->misc)) {
+		dev_err(dev, "failed to find SPEAr13xx misc regmap\n");
+		return PTR_ERR(cfgpriv->misc);
+	}
+
+	np_ahci = of_find_node_by_name(NULL, "ahci");
+	while (!IS_ERR_OR_NULL(np_ahci)) {
+		if (of_device_is_available(np_ahci)) {
+			ahci_pdev = of_find_device_by_node(np_ahci);
+			if (IS_ERR_OR_NULL(ahci_pdev)) {
+				dev_err(dev, "failed to find ahci platform device\n");
+				BUG();
+			}
+
+			ahci_pdata->driver_data = cfgpriv;
+			ret = platform_device_add_data(ahci_pdev, ahci_pdata,
+					sizeof(*ahci_pdata));
+			if (ret)
+				dev_err(dev, "failed to add ahci plat data\n");
+		}
+
+		np_ahci = of_find_node_by_name(np_ahci, "ahci");
+	}
+
+	return ret;
+}
+
+static int __exit spear13xx_cfg_remove(struct platform_device *pdev)
+{
+	return 0;
+}
+
+static struct platform_driver spear13xx_cfg_driver = {
+	.remove		= __exit_p(spear13xx_cfg_remove),
+	.driver = {
+		.name = "spear13xx-sata_pcie-cfg",
+		.owner = THIS_MODULE,
+		.of_match_table = of_match_ptr(spear13xx_cfg_of_match),
+	},
+};
+
+static int __init spear13xx_cfg_init(void)
+{
+
+	return platform_driver_probe(&spear13xx_cfg_driver,
+				spear13xx_cfg_probe);
+}
+arch_initcall(spear13xx_cfg_init);
+
+MODULE_DESCRIPTION("ST SPEAr13xx system configuration driver");
+MODULE_AUTHOR("Pratyush Anand <pratyush.anand@st.com>");
+MODULE_LICENSE("GPL v2");
-- 
1.7.0.1

[PATCH V2 5/8] clk: SPEAr13xx: Fix pcie clock name

[Mohit Kumar]

From: Pratyush Anand <pratyush.anand@st.com>

Follow dt clock naming convention for PCIe clocks.

Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: spear-devel at list.st.com
Cc: linux-arm-kernel at lists.infradead.org
Cc: Arnd Bergmann <arnd@arndb.de>
---
 drivers/clk/spear/spear1310_clock.c |    6 +++---
 drivers/clk/spear/spear1340_clock.c |    2 +-
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/drivers/clk/spear/spear1310_clock.c b/drivers/clk/spear/spear1310_clock.c
index 65894f7..4daa597 100644
--- a/drivers/clk/spear/spear1310_clock.c
+++ b/drivers/clk/spear/spear1310_clock.c
@@ -742,19 +742,19 @@ void __init spear1310_clk_init(void __iomem *misc_base, void __iomem *ras_base)
 	clk = clk_register_gate(NULL, "pcie_sata_0_clk", "ahb_clk", 0,
 			SPEAR1310_PERIP1_CLK_ENB, SPEAR1310_PCIE_SATA_0_CLK_ENB,
 			0, &_lock);
-	clk_register_clkdev(clk, NULL, "dw_pcie.0");
+	clk_register_clkdev(clk, NULL, "b1000000.pcie");
 	clk_register_clkdev(clk, NULL, "b1000000.ahci");
 
 	clk = clk_register_gate(NULL, "pcie_sata_1_clk", "ahb_clk", 0,
 			SPEAR1310_PERIP1_CLK_ENB, SPEAR1310_PCIE_SATA_1_CLK_ENB,
 			0, &_lock);
-	clk_register_clkdev(clk, NULL, "dw_pcie.1");
+	clk_register_clkdev(clk, NULL, "b1800000.pcie");
 	clk_register_clkdev(clk, NULL, "b1800000.ahci");
 
 	clk = clk_register_gate(NULL, "pcie_sata_2_clk", "ahb_clk", 0,
 			SPEAR1310_PERIP1_CLK_ENB, SPEAR1310_PCIE_SATA_2_CLK_ENB,
 			0, &_lock);
-	clk_register_clkdev(clk, NULL, "dw_pcie.2");
+	clk_register_clkdev(clk, NULL, "b4000000.pcie");
 	clk_register_clkdev(clk, NULL, "b4000000.ahci");
 
 	clk = clk_register_gate(NULL, "sysram0_clk", "ahb_clk", 0,
diff --git a/drivers/clk/spear/spear1340_clock.c b/drivers/clk/spear/spear1340_clock.c
index fe835c1..5a5c664 100644
--- a/drivers/clk/spear/spear1340_clock.c
+++ b/drivers/clk/spear/spear1340_clock.c
@@ -839,7 +839,7 @@ void __init spear1340_clk_init(void __iomem *misc_base)
 	clk = clk_register_gate(NULL, "pcie_sata_clk", "ahb_clk", 0,
 			SPEAR1340_PERIP1_CLK_ENB, SPEAR1340_PCIE_SATA_CLK_ENB,
 			0, &_lock);
-	clk_register_clkdev(clk, NULL, "dw_pcie");
+	clk_register_clkdev(clk, NULL, "b1000000.pcie");
 	clk_register_clkdev(clk, NULL, "b1000000.ahci");
 
 	clk = clk_register_gate(NULL, "sysram0_clk", "ahb_clk", 0,
-- 
1.7.0.1

[PATCH V2 6/8] SPEAr13xx: Fix static mapping table

[Mohit Kumar]

From: Pratyush Anand <pratyush.anand@st.com>

SPEAr13xx was using virtual address space 0xFE000000 to map physical address
space 0xB3000000. pci_remap_io uses 0xFEE00000 as virtual address. So
change 0xFE000000 to 0xF9000000.

Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
Tested-by: Mohit Kumar <mohit.kumar@st.com>
Cc: Viresh Kumar <viresh.linux@gmail.com>
Cc: spear-devel at list.st.com
Cc: linux-arm-kernel at lists.infradead.org
Cc: Arnd Bergmann <arnd@arndb.de>
---
 arch/arm/mach-spear/include/mach/spear.h |    4 ++--
 arch/arm/mach-spear/spear13xx.c          |    2 +-
 2 files changed, 3 insertions(+), 3 deletions(-)

diff --git a/arch/arm/mach-spear/include/mach/spear.h b/arch/arm/mach-spear/include/mach/spear.h
index 5cdc53d..f2d6a01 100644
--- a/arch/arm/mach-spear/include/mach/spear.h
+++ b/arch/arm/mach-spear/include/mach/spear.h
@@ -52,10 +52,10 @@
 #ifdef CONFIG_ARCH_SPEAR13XX
 
 #define PERIP_GRP2_BASE				UL(0xB3000000)
-#define VA_PERIP_GRP2_BASE			IOMEM(0xFE000000)
+#define VA_PERIP_GRP2_BASE			IOMEM(0xF9000000)
 #define MCIF_SDHCI_BASE				UL(0xB3000000)
 #define SYSRAM0_BASE				UL(0xB3800000)
-#define VA_SYSRAM0_BASE				IOMEM(0xFE800000)
+#define VA_SYSRAM0_BASE				IOMEM(0xF9800000)
 #define SYS_LOCATION				(VA_SYSRAM0_BASE + 0x600)
 
 #define PERIP_GRP1_BASE				UL(0xE0000000)
diff --git a/arch/arm/mach-spear/spear13xx.c b/arch/arm/mach-spear/spear13xx.c
index 7aa6e8c..20ce885 100644
--- a/arch/arm/mach-spear/spear13xx.c
+++ b/arch/arm/mach-spear/spear13xx.c
@@ -52,10 +52,10 @@ void __init spear13xx_l2x0_init(void)
 /*
  * Following will create 16MB static virtual/physical mappings
  * PHYSICAL		VIRTUAL
- * 0xB3000000		0xFE000000
  * 0xE0000000		0xFD000000
  * 0xEC000000		0xFC000000
  * 0xED000000		0xFB000000
+ * 0xB3000000		0xF9000000
  */
 struct map_desc spear13xx_io_desc[] __initdata = {
 	{
-- 
1.7.0.1

[PATCH V2 0/8] PCI: Add SPEAr13xx PCIe support

[Mohit Kumar]

First five patches are improvement and fixes for SPEAr13xx support.

PCIe driver support for SPEAr1310/40 platform board is added.
These patches are tested with SPEAr1310 evaluation board:
	- INTEL PRO 100/100 EP card
	- USB xhci gen2 card
 	- Above cards connected through LeCROY PTC switch

Modifications for SATA are tested with SPEAr1340-evb board

Changes since v1:
- Few patches of the series are already accepted and applied to mainline e.g.
 pcie designware driver improvements,fixes for IO translation bug, PCIe dw
 driver maintainer. So dropped these from v2.
- Incorporated comment to move the common/reset PCIe code to the seperate driver
- PCIe and SATA share common PHY configuration registers, so move SATA
 platform code to the system config driver
- Incorporated comments for FUSE_FS option for defconfig 
- Incorporated comments to move back the SPEAr1340 definations from .h file

Mohit Kumar (3):
  SPEAr13xx: Set dt field entry <stmmac,phy-addr> for phy probe
  SPEAr13xx: defconfig: Update
  MAINTAINERS: Add ST SPEAr13xx PCIe driver maintainer

Pratyush Anand (5):
  ahci: Add a driver_data field to struct ahci_platform_data
  SPEAr13xx: Fixup: Move SPEAr1340 SATA platform code to system cfg
    driver
  clk: SPEAr13xx: Fix pcie clock name
  SPEAr13xx: Fix static mapping table
  pcie: SPEAr13xx: Add designware pcie support

 MAINTAINERS                              |    6 +
 arch/arm/boot/dts/spear13xx.dtsi         |   63 ++++-
 arch/arm/configs/spear13xx_defconfig     |   16 +
 arch/arm/mach-spear/Kconfig              |    2 +
 arch/arm/mach-spear/include/mach/spear.h |    4 +-
 arch/arm/mach-spear/spear1340.c          |  127 +---------
 arch/arm/mach-spear/spear13xx.c          |    2 +-
 drivers/clk/spear/spear1310_clock.c      |    6 +-
 drivers/clk/spear/spear1340_clock.c      |    2 +-
 drivers/mfd/Makefile                     |    1 +
 drivers/mfd/spear13xx-cfg.c              |  444 ++++++++++++++++++++++++++++++
 drivers/pci/host/Kconfig                 |    5 +
 drivers/pci/host/Makefile                |    1 +
 drivers/pci/host/pcie-spear13xx.c        |  394 ++++++++++++++++++++++++++
 include/linux/ahci_platform.h            |    1 +
 15 files changed, 939 insertions(+), 135 deletions(-)
 create mode 100644 drivers/mfd/spear13xx-cfg.c
 create mode 100644 drivers/pci/host/pcie-spear13xx.c

[PATCH V2 3/8] ahci: Add a driver_data field to struct ahci_platform_data

[Tejun Heo]

On Thu, Jan 23, 2014 at 04:02:43PM +0530, Mohit Kumar wrote:
> diff --git a/include/linux/ahci_platform.h b/include/linux/ahci_platform.h
> index 73a2500..76d35e8 100644
> --- a/include/linux/ahci_platform.h
> +++ b/include/linux/ahci_platform.h
> @@ -28,6 +28,7 @@ struct ahci_platform_data {
>  	const struct ata_port_info *ata_port_info;
>  	unsigned int force_port_map;
>  	unsigned int mask_port_map;
> +	void *driver_data;

Please use private_data instead for consistency with other ata data
structures.

Thanks.

-- 
tejun

[PATCH V2 6/8] SPEAr13xx: Fix static mapping table

[Arnd Bergmann]

On Thursday 23 January 2014, Mohit Kumar wrote:
> From: Pratyush Anand <pratyush.anand@st.com>
> 
> SPEAr13xx was using virtual address space 0xFE000000 to map physical address
> space 0xB3000000. pci_remap_io uses 0xFEE00000 as virtual address. So
> change 0xFE000000 to 0xF9000000.
> 
> Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
> Tested-by: Mohit Kumar <mohit.kumar@st.com>
> Cc: Viresh Kumar <viresh.linux@gmail.com>
> Cc: spear-devel at list.st.com
> Cc: linux-arm-kernel at lists.infradead.org
> Cc: Arnd Bergmann <arnd@arndb.de>

Surely this is needed in backports, so please add stable at vger.kernel.org
to the Cc list in the changeset text. Otherwise

Acked-by: Arnd Bergmann <arnd@arndb.de>

[PATCH V2 4/8] SPEAr13xx: Fixup: Move SPEAr1340 SATA platform code to system cfg driver

[Arnd Bergmann]

On Thursday 23 January 2014, Mohit Kumar wrote:
> diff --git a/arch/arm/boot/dts/spear13xx.dtsi b/arch/arm/boot/dts/spear13xx.dtsi
> index 3518803..2b4e58e 100644
> --- a/arch/arm/boot/dts/spear13xx.dtsi
> +++ b/arch/arm/boot/dts/spear13xx.dtsi
> @@ -78,6 +78,10 @@
>  		status = "disabled";
>  	};
>  
> +	cfg {
> +		compatible = "st,spear13xx-cfg";
> +	};
> +
>  	ahb {
>  		#address-cells = <1>;
>  		#size-cells = <1>;

I only saw some of the patches, and did not get a patch with the binding
description for this device. Please forward that patch to me, or add it
to the series if you didn't have one.

I assume you'd want a phandle pointing to the syscon device in here
as well?

Regarding the naming, please do not use 'xx' wildcards in DT compatible
strings. Instead, use the exact model name of the first supported
version of the hardware (e.g. spear1300 or spear600) that remains
compatible. If there are minor variations between the versions,
use a list with the most specific version as well as the older ones
it's compatible with.

> @@ -221,6 +225,11 @@
>  				  0xd8000000 0xd8000000 0x01000000
>  				  0xe0000000 0xe0000000 0x10000000>;
>  
> +			misc: misc at e0700000 {
> +				compatible = "st,spear13xx-misc", "syscon";
> +				reg = <0xe0700000 0x1000>;
> +			};
> +

Same here. Also, I would make this 'misc: syscon at e0700000', since 'misc'
does not seem like an appropriate device name.


> +/* SPEAr1340 Registers */
> +/* Power Management Registers */
> +#define SPEAR1340_PCM_CFG			0x100
> +	#define SPEAR1340_PCM_CFG_SATA_POWER_EN	0x800
> +#define SPEAR1340_PCM_WKUP_CFG			0x104
> +#define SPEAR1340_SWITCH_CTR			0x108
> +
> +#define SPEAR1340_PERIP1_SW_RST			0x318
> +	#define SPEAR1340_PERIP1_SW_RST_SATA	0x1000
> +#define SPEAR1340_PERIP2_SW_RST			0x31C
> +#define SPEAR1340_PERIP3_SW_RST			0x320
> +
> +/* PCIE - SATA configuration registers */
> +#define SPEAR1340_PCIE_SATA_CFG			0x424
> +	/* PCIE CFG MASks */
> +	#define SPEAR1340_PCIE_CFG_DEVICE_PRESENT	(1 << 11)
> +	#define SPEAR1340_PCIE_CFG_POWERUP_RESET	(1 << 10)
> +	#define SPEAR1340_PCIE_CFG_CORE_CLK_EN		(1 << 9)
> +	#define SPEAR1340_PCIE_CFG_AUX_CLK_EN		(1 << 8)
> +	#define SPEAR1340_SATA_CFG_TX_CLK_EN		(1 << 4)
> +	#define SPEAR1340_SATA_CFG_RX_CLK_EN		(1 << 3)
> +	#define SPEAR1340_SATA_CFG_POWERUP_RESET	(1 << 2)
> +	#define SPEAR1340_SATA_CFG_PM_CLK_EN		(1 << 1)
> +	#define SPEAR1340_PCIE_SATA_SEL_PCIE		(0)
> +	#define SPEAR1340_PCIE_SATA_SEL_SATA		(1)
> +	#define SPEAR1340_PCIE_SATA_CFG_MASK		0xF1F
> +	#define SPEAR1340_PCIE_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_PCIE | \
> +			SPEAR1340_PCIE_CFG_AUX_CLK_EN | \
> +			SPEAR1340_PCIE_CFG_CORE_CLK_EN | \
> +			SPEAR1340_PCIE_CFG_POWERUP_RESET | \
> +			SPEAR1340_PCIE_CFG_DEVICE_PRESENT)
> +	#define SPEAR1340_SATA_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_SATA | \
> +			SPEAR1340_SATA_CFG_PM_CLK_EN | \
> +			SPEAR1340_SATA_CFG_POWERUP_RESET | \
> +			SPEAR1340_SATA_CFG_RX_CLK_EN | \
> +			SPEAR1340_SATA_CFG_TX_CLK_EN)
> +
> +#define SPEAR1340_PCIE_MIPHY_CFG		0x428
> +	#define SPEAR1340_MIPHY_OSC_BYPASS_EXT		(1 << 31)
> +	#define SPEAR1340_MIPHY_CLK_REF_DIV2		(1 << 27)
> +	#define SPEAR1340_MIPHY_CLK_REF_DIV4		(2 << 27)
> +	#define SPEAR1340_MIPHY_CLK_REF_DIV8		(3 << 27)
> +	#define SPEAR1340_MIPHY_PLL_RATIO_TOP(x)	(x << 0)
> +	#define SPEAR1340_PCIE_MIPHY_CFG_MASK		0xF80000FF
> +	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA \
> +			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
> +			SPEAR1340_MIPHY_CLK_REF_DIV2 | \
> +			SPEAR1340_MIPHY_PLL_RATIO_TOP(60))
> +	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK \
> +			(SPEAR1340_MIPHY_PLL_RATIO_TOP(120))
> +	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_PCIE \
> +			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
> +			SPEAR1340_MIPHY_PLL_RATIO_TOP(25))
> +
> +struct spear13xx_cfg_priv {
> +	struct regmap		*misc;
> +};
> +
> +/* SATA device registration */
> +static void spear1340_sata_miphy_init(struct spear13xx_cfg_priv *cfgpriv)
> +{
> +	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCIE_SATA_CFG,
> +			SPEAR1340_PCIE_SATA_CFG_MASK, SPEAR1340_SATA_CFG_VAL);
> +	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCIE_MIPHY_CFG,
> +			SPEAR1340_PCIE_MIPHY_CFG_MASK,
> +			SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK);
> +	/* Switch on sata power domain */
> +	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCM_CFG,
> +			SPEAR1340_PCM_CFG_SATA_POWER_EN,
> +			SPEAR1340_PCM_CFG_SATA_POWER_EN);
> +	msleep(20);
> +	/* Disable PCIE SATA Controller reset */
> +	regmap_update_bits(cfgpriv->misc, SPEAR1340_PERIP1_SW_RST,
> +			SPEAR1340_PERIP1_SW_RST_SATA, 0);
> +	msleep(20);
> +}

Looking at the actual code now, this very much looks like it ought to
be a "phy" driver and get put in drivers/phy/.

Please see the recent mailing list discussions about making the ahci
driver more generic. Once you put this code in a proper phy driver,
you should be able to avoid a lot of your workaround and just use
the regular ahci-platform driver without any hand-crafted platform
data callbacks.

	Arnd

[PATCH V2 3/8] ahci: Add a driver_data field to struct ahci_platform_data

[Pratyush Anand]

On Thu, Jan 23, 2014 at 07:36:44PM +0800, Tejun Heo wrote:
> On Thu, Jan 23, 2014 at 04:02:43PM +0530, Mohit Kumar wrote:
> > diff --git a/include/linux/ahci_platform.h b/include/linux/ahci_platform.h
> > index 73a2500..76d35e8 100644
> > --- a/include/linux/ahci_platform.h
> > +++ b/include/linux/ahci_platform.h
> > @@ -28,6 +28,7 @@ struct ahci_platform_data {
> >  	const struct ata_port_info *ata_port_info;
> >  	unsigned int force_port_map;
> >  	unsigned int mask_port_map;
> > +	void *driver_data;
> 
> Please use private_data instead for consistency with other ata data
> structures.

Ok.. ll do that in V3.

Thanks for your review.

Regards
Pratyush
> 
> Thanks.
> 
> -- 
> tejun

[PATCH V2 6/8] SPEAr13xx: Fix static mapping table

[Pratyush Anand]

On Thu, Jan 23, 2014 at 08:12:15PM +0800, Arnd Bergmann wrote:
> On Thursday 23 January 2014, Mohit Kumar wrote:
> > From: Pratyush Anand <pratyush.anand@st.com>
> > 
> > SPEAr13xx was using virtual address space 0xFE000000 to map physical address
> > space 0xB3000000. pci_remap_io uses 0xFEE00000 as virtual address. So
> > change 0xFE000000 to 0xF9000000.
> > 
> > Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
> > Tested-by: Mohit Kumar <mohit.kumar@st.com>
> > Cc: Viresh Kumar <viresh.linux@gmail.com>
> > Cc: spear-devel at list.st.com
> > Cc: linux-arm-kernel at lists.infradead.org
> > Cc: Arnd Bergmann <arnd@arndb.de>
> 
> Surely this is needed in backports, so please add stable at vger.kernel.org
> to the Cc list in the changeset text. Otherwise

While sending v3 of series will cc stable list.

> 
> Acked-by: Arnd Bergmann <arnd@arndb.de>

Thanks :)

Regards
Pratyush

[PATCH V2 4/8] SPEAr13xx: Fixup: Move SPEAr1340 SATA platform code to system cfg driver

[Pratyush Anand]

Hi Arnd,

Thanks for your valuable comments.

On Thu, Jan 23, 2014 at 08:22:54PM +0800, Arnd Bergmann wrote:
> On Thursday 23 January 2014, Mohit Kumar wrote:
> > diff --git a/arch/arm/boot/dts/spear13xx.dtsi b/arch/arm/boot/dts/spear13xx.dtsi
> > index 3518803..2b4e58e 100644
> > --- a/arch/arm/boot/dts/spear13xx.dtsi
> > +++ b/arch/arm/boot/dts/spear13xx.dtsi
> > @@ -78,6 +78,10 @@
> >  		status = "disabled";
> >  	};
> >  
> > +	cfg {
> > +		compatible = "st,spear13xx-cfg";
> > +	};
> > +
> >  	ahb {
> >  		#address-cells = <1>;
> >  		#size-cells = <1>;
> 
> I only saw some of the patches, and did not get a patch with the binding
> description for this device. Please forward that patch to me, or add it
> to the series if you didn't have one.

It was not there.
Will add a patch for the same in v3.

> 
> I assume you'd want a phandle pointing to the syscon device in here
> as well?

Since there is only one syscon device in the whole DT, so do I really
need to add phandle? Currently I am using
syscon_regmap_lookup_by_compatible to find  syscon device.

> 
> Regarding the naming, please do not use 'xx' wildcards in DT compatible
> strings. Instead, use the exact model name of the first supported
> version of the hardware (e.g. spear1300 or spear600) that remains
> compatible. If there are minor variations between the versions,
> use a list with the most specific version as well as the older ones
> it's compatible with.

Ok..ll take care.

> 
> > @@ -221,6 +225,11 @@
> >  				  0xd8000000 0xd8000000 0x01000000
> >  				  0xe0000000 0xe0000000 0x10000000>;
> >  
> > +			misc: misc at e0700000 {
> > +				compatible = "st,spear13xx-misc", "syscon";
> > +				reg = <0xe0700000 0x1000>;
> > +			};
> > +
> 
> Same here. Also, I would make this 'misc: syscon at e0700000', since 'misc'
> does not seem like an appropriate device name.

Ok.

> 
> 
> > +/* SPEAr1340 Registers */
> > +/* Power Management Registers */
> > +#define SPEAR1340_PCM_CFG			0x100
> > +	#define SPEAR1340_PCM_CFG_SATA_POWER_EN	0x800
> > +#define SPEAR1340_PCM_WKUP_CFG			0x104
> > +#define SPEAR1340_SWITCH_CTR			0x108
> > +
> > +#define SPEAR1340_PERIP1_SW_RST			0x318
> > +	#define SPEAR1340_PERIP1_SW_RST_SATA	0x1000
> > +#define SPEAR1340_PERIP2_SW_RST			0x31C
> > +#define SPEAR1340_PERIP3_SW_RST			0x320
> > +
> > +/* PCIE - SATA configuration registers */
> > +#define SPEAR1340_PCIE_SATA_CFG			0x424
> > +	/* PCIE CFG MASks */
> > +	#define SPEAR1340_PCIE_CFG_DEVICE_PRESENT	(1 << 11)
> > +	#define SPEAR1340_PCIE_CFG_POWERUP_RESET	(1 << 10)
> > +	#define SPEAR1340_PCIE_CFG_CORE_CLK_EN		(1 << 9)
> > +	#define SPEAR1340_PCIE_CFG_AUX_CLK_EN		(1 << 8)
> > +	#define SPEAR1340_SATA_CFG_TX_CLK_EN		(1 << 4)
> > +	#define SPEAR1340_SATA_CFG_RX_CLK_EN		(1 << 3)
> > +	#define SPEAR1340_SATA_CFG_POWERUP_RESET	(1 << 2)
> > +	#define SPEAR1340_SATA_CFG_PM_CLK_EN		(1 << 1)
> > +	#define SPEAR1340_PCIE_SATA_SEL_PCIE		(0)
> > +	#define SPEAR1340_PCIE_SATA_SEL_SATA		(1)
> > +	#define SPEAR1340_PCIE_SATA_CFG_MASK		0xF1F
> > +	#define SPEAR1340_PCIE_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_PCIE | \
> > +			SPEAR1340_PCIE_CFG_AUX_CLK_EN | \
> > +			SPEAR1340_PCIE_CFG_CORE_CLK_EN | \
> > +			SPEAR1340_PCIE_CFG_POWERUP_RESET | \
> > +			SPEAR1340_PCIE_CFG_DEVICE_PRESENT)
> > +	#define SPEAR1340_SATA_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_SATA | \
> > +			SPEAR1340_SATA_CFG_PM_CLK_EN | \
> > +			SPEAR1340_SATA_CFG_POWERUP_RESET | \
> > +			SPEAR1340_SATA_CFG_RX_CLK_EN | \
> > +			SPEAR1340_SATA_CFG_TX_CLK_EN)
> > +
> > +#define SPEAR1340_PCIE_MIPHY_CFG		0x428
> > +	#define SPEAR1340_MIPHY_OSC_BYPASS_EXT		(1 << 31)
> > +	#define SPEAR1340_MIPHY_CLK_REF_DIV2		(1 << 27)
> > +	#define SPEAR1340_MIPHY_CLK_REF_DIV4		(2 << 27)
> > +	#define SPEAR1340_MIPHY_CLK_REF_DIV8		(3 << 27)
> > +	#define SPEAR1340_MIPHY_PLL_RATIO_TOP(x)	(x << 0)
> > +	#define SPEAR1340_PCIE_MIPHY_CFG_MASK		0xF80000FF
> > +	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA \
> > +			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
> > +			SPEAR1340_MIPHY_CLK_REF_DIV2 | \
> > +			SPEAR1340_MIPHY_PLL_RATIO_TOP(60))
> > +	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK \
> > +			(SPEAR1340_MIPHY_PLL_RATIO_TOP(120))
> > +	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_PCIE \
> > +			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
> > +			SPEAR1340_MIPHY_PLL_RATIO_TOP(25))
> > +
> > +struct spear13xx_cfg_priv {
> > +	struct regmap		*misc;
> > +};
> > +
> > +/* SATA device registration */
> > +static void spear1340_sata_miphy_init(struct spear13xx_cfg_priv *cfgpriv)
> > +{
> > +	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCIE_SATA_CFG,
> > +			SPEAR1340_PCIE_SATA_CFG_MASK, SPEAR1340_SATA_CFG_VAL);
> > +	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCIE_MIPHY_CFG,
> > +			SPEAR1340_PCIE_MIPHY_CFG_MASK,
> > +			SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK);
> > +	/* Switch on sata power domain */
> > +	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCM_CFG,
> > +			SPEAR1340_PCM_CFG_SATA_POWER_EN,
> > +			SPEAR1340_PCM_CFG_SATA_POWER_EN);
> > +	msleep(20);
> > +	/* Disable PCIE SATA Controller reset */
> > +	regmap_update_bits(cfgpriv->misc, SPEAR1340_PERIP1_SW_RST,
> > +			SPEAR1340_PERIP1_SW_RST_SATA, 0);
> > +	msleep(20);
> > +}
> 
> Looking at the actual code now, this very much looks like it ought to
> be a "phy" driver and get put in drivers/phy/.

Actually these registers are part of common system configurations
register space (called as misc space) for SPEAr SOC. So we opted for
syscon framework.

PHY registers space starts from 0xEB800000, which can be
programmed for various phy specific functions like power management,
tx/rx settings, comparator settings etc. In most of the cases phy
works with default settings, however there are few exceptions for
which we will be adding a phy driver for further improvement of SPEAr
drivers.

Regards
Pratyush
> 
> Please see the recent mailing list discussions about making the ahci
> driver more generic. Once you put this code in a proper phy driver,
> you should be able to avoid a lot of your workaround and just use
> the regular ahci-platform driver without any hand-crafted platform
> data callbacks.
> 
> 	Arnd

[PATCH V2 1/8] SPEAr13xx: Set dt field entry <stmmac,phy-addr> for phy probe

[Viresh Kumar]

On Thu, Jan 23, 2014 at 4:02 PM, Mohit Kumar <mohit.kumar@st.com> wrote:
> DT field name for the phy address changed since kernel 3.10. Set the
> snps,phy-addr to 0xffffffff so that the driver probes for the phy.
>
> Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
> Cc: Pratyush Anand <pratyush.anand@st.com>
> Cc: Viresh Kumar <viresh.linux@gmail.com>
> Cc: spear-devel at list.st.com
> Cc: linux-arm-kernel at lists.infradead.org
> Cc: devicetree at vger.kernel.org
> ---
>  arch/arm/boot/dts/spear13xx.dtsi |    1 +
>  1 files changed, 1 insertions(+), 0 deletions(-)
>
> diff --git a/arch/arm/boot/dts/spear13xx.dtsi b/arch/arm/boot/dts/spear13xx.dtsi
> index 4382547..3518803 100644
> --- a/arch/arm/boot/dts/spear13xx.dtsi
> +++ b/arch/arm/boot/dts/spear13xx.dtsi
> @@ -155,6 +155,7 @@
>
>                 gmac0: eth at e2000000 {
>                         compatible = "st,spear600-gmac";
> +                       snps,phy-addr = <0xffffffff>;
>                         reg = <0xe2000000 0x8000>;
>                         interrupts = <0 33 0x4
>                                       0 34 0x4>;

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>

[PATCH V2 2/8] SPEAr13xx: defconfig: Update

[Viresh Kumar]

On Thu, Jan 23, 2014 at 4:02 PM, Mohit Kumar <mohit.kumar@st.com> wrote:
> Enable EABI, OEABI, VFP and NFS configs in default configuration file for
> SPEAr13xx.
>
> Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
> Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
> Cc: Mohit Kumar <mohit.kumar@st.com>
> Cc: Viresh Kumar <viresh.linux@gmail.com>
> Cc: spear-devel at list.st.com
> Cc: linux-arm-kernel at lists.infradead.org

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>

[PATCH V2 5/8] clk: SPEAr13xx: Fix pcie clock name

[Viresh Kumar]

On Thu, Jan 23, 2014 at 4:02 PM, Mohit Kumar <mohit.kumar@st.com> wrote:
> From: Pratyush Anand <pratyush.anand@st.com>
>
> Follow dt clock naming convention for PCIe clocks.
>
> Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
> Tested-by: Mohit Kumar <mohit.kumar@st.com>
> Cc: Viresh Kumar <viresh.linux@gmail.com>
> Cc: spear-devel at list.st.com
> Cc: linux-arm-kernel at lists.infradead.org
> Cc: Arnd Bergmann <arnd@arndb.de>
> ---
>  drivers/clk/spear/spear1310_clock.c |    6 +++---
>  drivers/clk/spear/spear1340_clock.c |    2 +-
>  2 files changed, 4 insertions(+), 4 deletions(-)

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>

[PATCH V2 6/8] SPEAr13xx: Fix static mapping table

[Viresh Kumar]

On Thu, Jan 23, 2014 at 4:02 PM, Mohit Kumar <mohit.kumar@st.com> wrote:
> From: Pratyush Anand <pratyush.anand@st.com>
>
> SPEAr13xx was using virtual address space 0xFE000000 to map physical address
> space 0xB3000000. pci_remap_io uses 0xFEE00000 as virtual address. So
> change 0xFE000000 to 0xF9000000.
>
> Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
> Tested-by: Mohit Kumar <mohit.kumar@st.com>
> Cc: Viresh Kumar <viresh.linux@gmail.com>
> Cc: spear-devel at list.st.com
> Cc: linux-arm-kernel at lists.infradead.org
> Cc: Arnd Bergmann <arnd@arndb.de>
> ---
>  arch/arm/mach-spear/include/mach/spear.h |    4 ++--
>  arch/arm/mach-spear/spear13xx.c          |    2 +-
>  2 files changed, 3 insertions(+), 3 deletions(-)
>
> diff --git a/arch/arm/mach-spear/include/mach/spear.h b/arch/arm/mach-spear/include/mach/spear.h
> index 5cdc53d..f2d6a01 100644
> --- a/arch/arm/mach-spear/include/mach/spear.h
> +++ b/arch/arm/mach-spear/include/mach/spear.h
> @@ -52,10 +52,10 @@
>  #ifdef CONFIG_ARCH_SPEAR13XX
>
>  #define PERIP_GRP2_BASE                                UL(0xB3000000)
> -#define VA_PERIP_GRP2_BASE                     IOMEM(0xFE000000)
> +#define VA_PERIP_GRP2_BASE                     IOMEM(0xF9000000)
>  #define MCIF_SDHCI_BASE                                UL(0xB3000000)
>  #define SYSRAM0_BASE                           UL(0xB3800000)
> -#define VA_SYSRAM0_BASE                                IOMEM(0xFE800000)
> +#define VA_SYSRAM0_BASE                                IOMEM(0xF9800000)
>  #define SYS_LOCATION                           (VA_SYSRAM0_BASE + 0x600)
>
>  #define PERIP_GRP1_BASE                                UL(0xE0000000)
> diff --git a/arch/arm/mach-spear/spear13xx.c b/arch/arm/mach-spear/spear13xx.c
> index 7aa6e8c..20ce885 100644
> --- a/arch/arm/mach-spear/spear13xx.c
> +++ b/arch/arm/mach-spear/spear13xx.c
> @@ -52,10 +52,10 @@ void __init spear13xx_l2x0_init(void)
>  /*
>   * Following will create 16MB static virtual/physical mappings
>   * PHYSICAL            VIRTUAL
> - * 0xB3000000          0xFE000000
>   * 0xE0000000          0xFD000000
>   * 0xEC000000          0xFC000000
>   * 0xED000000          0xFB000000
> + * 0xB3000000          0xF9000000


Why have you moved this to bottom of list? It was probably kept
in increasing order and so please keep the same.

Other than that:

Acked-by: Viresh Kumar <viresh.kumar@linaro.org>

[PATCH V2 6/8] SPEAr13xx: Fix static mapping table

[Pratyush Anand]

On Fri, Jan 24, 2014 at 01:07:38PM +0800, Viresh Kumar wrote:
> On Thu, Jan 23, 2014 at 4:02 PM, Mohit Kumar <mohit.kumar@st.com> wrote:
> > From: Pratyush Anand <pratyush.anand@st.com>
> >
> > SPEAr13xx was using virtual address space 0xFE000000 to map physical address
> > space 0xB3000000. pci_remap_io uses 0xFEE00000 as virtual address. So
> > change 0xFE000000 to 0xF9000000.
> >
> > Signed-off-by: Pratyush Anand <pratyush.anand@st.com>
> > Tested-by: Mohit Kumar <mohit.kumar@st.com>
> > Cc: Viresh Kumar <viresh.linux@gmail.com>
> > Cc: spear-devel at list.st.com
> > Cc: linux-arm-kernel at lists.infradead.org
> > Cc: Arnd Bergmann <arnd@arndb.de>
> > ---
> >  arch/arm/mach-spear/include/mach/spear.h |    4 ++--
> >  arch/arm/mach-spear/spear13xx.c          |    2 +-
> >  2 files changed, 3 insertions(+), 3 deletions(-)
> >
> > diff --git a/arch/arm/mach-spear/include/mach/spear.h b/arch/arm/mach-spear/include/mach/spear.h
> > index 5cdc53d..f2d6a01 100644
> > --- a/arch/arm/mach-spear/include/mach/spear.h
> > +++ b/arch/arm/mach-spear/include/mach/spear.h
> > @@ -52,10 +52,10 @@
> >  #ifdef CONFIG_ARCH_SPEAR13XX
> >
> >  #define PERIP_GRP2_BASE                                UL(0xB3000000)
> > -#define VA_PERIP_GRP2_BASE                     IOMEM(0xFE000000)
> > +#define VA_PERIP_GRP2_BASE                     IOMEM(0xF9000000)
> >  #define MCIF_SDHCI_BASE                                UL(0xB3000000)
> >  #define SYSRAM0_BASE                           UL(0xB3800000)
> > -#define VA_SYSRAM0_BASE                                IOMEM(0xFE800000)
> > +#define VA_SYSRAM0_BASE                                IOMEM(0xF9800000)
> >  #define SYS_LOCATION                           (VA_SYSRAM0_BASE + 0x600)
> >
> >  #define PERIP_GRP1_BASE                                UL(0xE0000000)
> > diff --git a/arch/arm/mach-spear/spear13xx.c b/arch/arm/mach-spear/spear13xx.c
> > index 7aa6e8c..20ce885 100644
> > --- a/arch/arm/mach-spear/spear13xx.c
> > +++ b/arch/arm/mach-spear/spear13xx.c
> > @@ -52,10 +52,10 @@ void __init spear13xx_l2x0_init(void)
> >  /*
> >   * Following will create 16MB static virtual/physical mappings
> >   * PHYSICAL            VIRTUAL
> > - * 0xB3000000          0xFE000000
> >   * 0xE0000000          0xFD000000
> >   * 0xEC000000          0xFC000000
> >   * 0xED000000          0xFB000000
> > + * 0xB3000000          0xF9000000
> 
> 
> Why have you moved this to bottom of list? It was probably kept
> in increasing order and so please keep the same.

Oh,yes..ll be corrected in v3 of series.

> 
> Other than that:
> 
> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>

Thanks.

Regards
Pratyush

[PATCH V2 1/8] SPEAr13xx: Set dt field entry <stmmac,phy-addr> for phy probe

[Chen-Yu Tsai]

Hi,

On Fri, Jan 24, 2014 at 1:02 PM, Viresh Kumar <viresh.kumar@linaro.org> wrote:
> On Thu, Jan 23, 2014 at 4:02 PM, Mohit Kumar <mohit.kumar@st.com> wrote:
>> DT field name for the phy address changed since kernel 3.10. Set the
>> snps,phy-addr to 0xffffffff so that the driver probes for the phy.

This will no longer be required. The default behavior for
DT based setups has been changed to auto-detecting the phy.

See http://patchwork.ozlabs.org/patch/312063/


Cheers
ChenYu

>>
>> Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
>> Cc: Pratyush Anand <pratyush.anand@st.com>
>> Cc: Viresh Kumar <viresh.linux@gmail.com>
>> Cc: spear-devel at list.st.com
>> Cc: linux-arm-kernel at lists.infradead.org
>> Cc: devicetree at vger.kernel.org
>> ---
>>  arch/arm/boot/dts/spear13xx.dtsi |    1 +
>>  1 files changed, 1 insertions(+), 0 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/spear13xx.dtsi b/arch/arm/boot/dts/spear13xx.dtsi
>> index 4382547..3518803 100644
>> --- a/arch/arm/boot/dts/spear13xx.dtsi
>> +++ b/arch/arm/boot/dts/spear13xx.dtsi
>> @@ -155,6 +155,7 @@
>>
>>                 gmac0: eth at e2000000 {
>>                         compatible = "st,spear600-gmac";
>> +                       snps,phy-addr = <0xffffffff>;
>>                         reg = <0xe2000000 0x8000>;
>>                         interrupts = <0 33 0x4
>>                                       0 34 0x4>;
>
> Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 1/8] SPEAr13xx: Set dt field entry <stmmac,phy-addr> for phy probe

[Mohit KUMAR DCG]

Hello Chen,

> -----Original Message-----
> From: wens213 at gmail.com [mailto:wens213 at gmail.com] On Behalf Of
> Chen-Yu Tsai
> Sent: Friday, January 24, 2014 11:33 AM
> To: Viresh Kumar
> Cc: Mohit KUMAR DCG; Pratyush ANAND; spear-devel; linux-arm-
> kernel at lists.infradead.org; devicetree
> Subject: Re: [PATCH V2 1/8] SPEAr13xx: Set dt field entry <stmmac,phy-
> addr> for phy probe
> 
> Hi,
> 
> On Fri, Jan 24, 2014 at 1:02 PM, Viresh Kumar <viresh.kumar@linaro.org>
> wrote:
> > On Thu, Jan 23, 2014 at 4:02 PM, Mohit Kumar <mohit.kumar@st.com>
> wrote:
> >> DT field name for the phy address changed since kernel 3.10. Set the
> >> snps,phy-addr to 0xffffffff so that the driver probes for the phy.
> 
> This will no longer be required. The default behavior for DT based setups has
> been changed to auto-detecting the phy.
> 
> See http://patchwork.ozlabs.org/patch/312063/
> 
- Thanks, we will test with your patch and remove this one from v3.

Regards
Mohit
> 
> Cheers
> ChenYu
> 
> >>
> >> Signed-off-by: Mohit Kumar <mohit.kumar@st.com>
> >> Cc: Pratyush Anand <pratyush.anand@st.com>
> >> Cc: Viresh Kumar <viresh.linux@gmail.com>
> >> Cc: spear-devel at list.st.com
> >> Cc: linux-arm-kernel at lists.infradead.org
> >> Cc: devicetree at vger.kernel.org
> >> ---
> >>  arch/arm/boot/dts/spear13xx.dtsi |    1 +
> >>  1 files changed, 1 insertions(+), 0 deletions(-)
> >>
> >> diff --git a/arch/arm/boot/dts/spear13xx.dtsi
> >> b/arch/arm/boot/dts/spear13xx.dtsi
> >> index 4382547..3518803 100644
> >> --- a/arch/arm/boot/dts/spear13xx.dtsi
> >> +++ b/arch/arm/boot/dts/spear13xx.dtsi
> >> @@ -155,6 +155,7 @@
> >>
> >>                 gmac0: eth at e2000000 {
> >>                         compatible = "st,spear600-gmac";
> >> +                       snps,phy-addr = <0xffffffff>;
> >>                         reg = <0xe2000000 0x8000>;
> >>                         interrupts = <0 33 0x4
> >>                                       0 34 0x4>;
> >
> > Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
> >
> > _______________________________________________
> > linux-arm-kernel mailing list
> > linux-arm-kernel at lists.infradead.org
> > http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH V2 4/8] SPEAr13xx: Fixup: Move SPEAr1340 SATA platform code to system cfg driver

[Arnd Bergmann]

On Friday 24 January 2014, Pratyush Anand wrote:
> On Thu, Jan 23, 2014 at 08:22:54PM +0800, Arnd Bergmann wrote:
> > On Thursday 23 January 2014, Mohit Kumar wrote:
> > 
> > I assume you'd want a phandle pointing to the syscon device in here
> > as well?
> 
> Since there is only one syscon device in the whole DT, so do I really
> need to add phandle? Currently I am using
> syscon_regmap_lookup_by_compatible to find  syscon device.

I'd much rather use syscon_regmap_lookup_by_phandle than
syscon_regmap_lookup_by_compatible, all the time, since this makes
the relationship between the devices explicit.
 
The phandle method also allows you to pass regmap indexes in the
same property, which can be handy if two variants of the chip have
the same registers at a different offset.

> > > +/* SPEAr1340 Registers */
> > > +/* Power Management Registers */
> > > +#define SPEAR1340_PCM_CFG			0x100
> > > +	#define SPEAR1340_PCM_CFG_SATA_POWER_EN	0x800
> > > +#define SPEAR1340_PCM_WKUP_CFG			0x104
> > > +#define SPEAR1340_SWITCH_CTR			0x108
> > > +
> > > +#define SPEAR1340_PERIP1_SW_RST			0x318
> > > +	#define SPEAR1340_PERIP1_SW_RST_SATA	0x1000
> > > +#define SPEAR1340_PERIP2_SW_RST			0x31C
> > > +#define SPEAR1340_PERIP3_SW_RST			0x320
> > > +
> > > +/* PCIE - SATA configuration registers */
> > > +#define SPEAR1340_PCIE_SATA_CFG			0x424
> > > +	/* PCIE CFG MASks */
> > > +	#define SPEAR1340_PCIE_CFG_DEVICE_PRESENT	(1 << 11)
> > > +	#define SPEAR1340_PCIE_CFG_POWERUP_RESET	(1 << 10)
> > > +	#define SPEAR1340_PCIE_CFG_CORE_CLK_EN		(1 << 9)
> > > +	#define SPEAR1340_PCIE_CFG_AUX_CLK_EN		(1 << 8)
> > > +	#define SPEAR1340_SATA_CFG_TX_CLK_EN		(1 << 4)
> > > +	#define SPEAR1340_SATA_CFG_RX_CLK_EN		(1 << 3)
> > > +	#define SPEAR1340_SATA_CFG_POWERUP_RESET	(1 << 2)
> > > +	#define SPEAR1340_SATA_CFG_PM_CLK_EN		(1 << 1)
> > > +	#define SPEAR1340_PCIE_SATA_SEL_PCIE		(0)
> > > +	#define SPEAR1340_PCIE_SATA_SEL_SATA		(1)
> > > +	#define SPEAR1340_PCIE_SATA_CFG_MASK		0xF1F
> > > +	#define SPEAR1340_PCIE_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_PCIE | \
> > > +			SPEAR1340_PCIE_CFG_AUX_CLK_EN | \
> > > +			SPEAR1340_PCIE_CFG_CORE_CLK_EN | \
> > > +			SPEAR1340_PCIE_CFG_POWERUP_RESET | \
> > > +			SPEAR1340_PCIE_CFG_DEVICE_PRESENT)
> > > +	#define SPEAR1340_SATA_CFG_VAL	(SPEAR1340_PCIE_SATA_SEL_SATA | \
> > > +			SPEAR1340_SATA_CFG_PM_CLK_EN | \
> > > +			SPEAR1340_SATA_CFG_POWERUP_RESET | \
> > > +			SPEAR1340_SATA_CFG_RX_CLK_EN | \
> > > +			SPEAR1340_SATA_CFG_TX_CLK_EN)
> > > +
> > > +#define SPEAR1340_PCIE_MIPHY_CFG		0x428
> > > +	#define SPEAR1340_MIPHY_OSC_BYPASS_EXT		(1 << 31)
> > > +	#define SPEAR1340_MIPHY_CLK_REF_DIV2		(1 << 27)
> > > +	#define SPEAR1340_MIPHY_CLK_REF_DIV4		(2 << 27)
> > > +	#define SPEAR1340_MIPHY_CLK_REF_DIV8		(3 << 27)
> > > +	#define SPEAR1340_MIPHY_PLL_RATIO_TOP(x)	(x << 0)
> > > +	#define SPEAR1340_PCIE_MIPHY_CFG_MASK		0xF80000FF
> > > +	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA \
> > > +			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
> > > +			SPEAR1340_MIPHY_CLK_REF_DIV2 | \
> > > +			SPEAR1340_MIPHY_PLL_RATIO_TOP(60))
> > > +	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK \
> > > +			(SPEAR1340_MIPHY_PLL_RATIO_TOP(120))
> > > +	#define SPEAR1340_PCIE_SATA_MIPHY_CFG_PCIE \
> > > +			(SPEAR1340_MIPHY_OSC_BYPASS_EXT | \
> > > +			SPEAR1340_MIPHY_PLL_RATIO_TOP(25))
> > > +
> > > +struct spear13xx_cfg_priv {
> > > +	struct regmap		*misc;
> > > +};
> > > +
> > > +/* SATA device registration */
> > > +static void spear1340_sata_miphy_init(struct spear13xx_cfg_priv *cfgpriv)
> > > +{
> > > +	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCIE_SATA_CFG,
> > > +			SPEAR1340_PCIE_SATA_CFG_MASK, SPEAR1340_SATA_CFG_VAL);
> > > +	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCIE_MIPHY_CFG,
> > > +			SPEAR1340_PCIE_MIPHY_CFG_MASK,
> > > +			SPEAR1340_PCIE_SATA_MIPHY_CFG_SATA_25M_CRYSTAL_CLK);
> > > +	/* Switch on sata power domain */
> > > +	regmap_update_bits(cfgpriv->misc, SPEAR1340_PCM_CFG,
> > > +			SPEAR1340_PCM_CFG_SATA_POWER_EN,
> > > +			SPEAR1340_PCM_CFG_SATA_POWER_EN);
> > > +	msleep(20);
> > > +	/* Disable PCIE SATA Controller reset */
> > > +	regmap_update_bits(cfgpriv->misc, SPEAR1340_PERIP1_SW_RST,
> > > +			SPEAR1340_PERIP1_SW_RST_SATA, 0);
> > > +	msleep(20);
> > > +}
> > 
> > Looking at the actual code now, this very much looks like it ought to
> > be a "phy" driver and get put in drivers/phy/.
> 
> Actually these registers are part of common system configurations
> register space (called as misc space) for SPEAr SOC. So we opted for
> syscon framework.

The use of syscon for this is good, I have no objection to that, and
was suggesting that you create a logical "phy" device that uses the
misc syscon device as a backend.
 
> PHY registers space starts from 0xEB800000, which can be
> programmed for various phy specific functions like power management,
> tx/rx settings, comparator settings etc. In most of the cases phy
> works with default settings, however there are few exceptions for
> which we will be adding a phy driver for further improvement of SPEAr
> drivers.

I see. So while the code you have here could be expressed as a phy driver
by itself, there is another part of the SoC that controls the actual
phy. How about if you add the phy device node to DT, and write a driver
that doesn't actually program the phy registers for now, but does contain
the code that you have posted here. That would give you flexibility for
future extensions and at the same time let you remove all SPEAr specific
code from the actual AHCI driver by using the generic ahci-platform
driver.

	Arnd

[PATCH V2 4/8] SPEAr13xx: Fixup: Move SPEAr1340 SATA platform code to system cfg driver

[Pratyush Anand]

Hi Arnd,


On Sat, Jan 25, 2014 at 2:23 AM, Arnd Bergmann <arnd@arndb.de> wrote:
>
> On Friday 24 January 2014, Pratyush Anand wrote:
> > On Thu, Jan 23, 2014 at 08:22:54PM +0800, Arnd Bergmann wrote:
> > > On Thursday 23 January 2014, Mohit Kumar wrote:
> > >
> > > I assume you'd want a phandle pointing to the syscon device in here
> > > as well?
> >
> > Since there is only one syscon device in the whole DT, so do I really
> > need to add phandle? Currently I am using
> > syscon_regmap_lookup_by_compatible to find  syscon device.
>
> I'd much rather use syscon_regmap_lookup_by_phandle than
> syscon_regmap_lookup_by_compatible, all the time, since this makes
> the relationship between the devices explicit.
>
> The phandle method also allows you to pass regmap indexes in the
> same property, which can be handy if two variants of the chip have
> the same registers at a different offset.
>
> > > > +/* SPEAr1340 Registers */
> > > > +/* Power Management Registers */

[...]

> > > Looking at the actual code now, this very much looks like it ought to
> > > be a "phy" driver and get put in drivers/phy/.
> >
> > Actually these registers are part of common system configurations
> > register space (called as misc space) for SPEAr SOC. So we opted for
> > syscon framework.
>
> The use of syscon for this is good, I have no objection to that, and
> was suggesting that you create a logical "phy" device that uses the
> misc syscon device as a backend.
>
> > PHY registers space starts from 0xEB800000, which can be
> > programmed for various phy specific functions like power management,
> > tx/rx settings, comparator settings etc. In most of the cases phy
> > works with default settings, however there are few exceptions for
> > which we will be adding a phy driver for further improvement of SPEAr
> > drivers.
>
> I see. So while the code you have here could be expressed as a phy driver
> by itself, there is another part of the SoC that controls the actual
> phy. How about if you add the phy device node to DT, and write a driver
> that doesn't actually program the phy registers for now, but does contain
> the code that you have posted here. That would give you flexibility for
> future extensions and at the same time let you remove all SPEAr specific
> code from the actual AHCI driver by using the generic ahci-platform
> driver.

OK..
--  will move all these code to a phy driver.
-- so, no need of a new cfg node as of now.
-- will pass syscon phandle to phy driver.
-- currently will keep ahci platform plugin (as it is here) in phy driver.
will remove when generic ahci driver is in place.

Regards
Pratyush
>
>         Arnd
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel