Re: [PATCH 7/8] arm64: dts: allwinner: rg35xx: Enable LCD output

["Jernej Škrabec" <jernej.skrabec@gmail.com>]

Dne nedelja, 16. februar 2025 ob 10:27:14 Srednjeevropski standardni čas je Ryan Walklin napisal(a):
> The RG35XX has a 640x480 RGB/SPI LCD panel, supported by the SoC display
> pipeline and an NV3052C controller. The H616 SOC's GPIO bank D contains
> the muxed display pins for RGB and LVDS output support.
> 
> Enable the display engine and LCD timing controller, configure the
> panel, and add a fixed 3.3v GPIO-controlled regulator for the panel, and
> a VCC supply for the display pins as per the other GPIO banks.
> 
> Signed-off-by: Ryan Walklin <ryan@testtoast.com>
> ---
>  .../sun50i-h700-anbernic-rg35xx-2024.dts      | 58 +++++++++++++++++++
>  1 file changed, 58 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
> index a231abf1684ad..388487d4720e2 100644
> --- a/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
> +++ b/arch/arm64/boot/dts/allwinner/sun50i-h700-anbernic-rg35xx-2024.dts
> @@ -175,6 +175,49 @@ reg_vcc5v: regulator-vcc5v { /* USB-C power input */
>  		regulator-min-microvolt = <5000000>;
>  		regulator-max-microvolt = <5000000>;
>  	};
> +
> +	reg_lcd: regulator-gpio-lcd-vdd {
> +		compatible = "regulator-fixed";
> +		regulator-min-microvolt = <3300000>;
> +		regulator-max-microvolt = <3300000>;
> +		regulator-name = "vdd-lcd";
> +		gpio = <&pio 8 15 GPIO_ACTIVE_HIGH>; // PI15
> +		enable-active-high;
> +	};
> +
> +	spi_lcd: spi {
> +		compatible = "spi-gpio";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		sck-gpios = <&pio 8 9 GPIO_ACTIVE_HIGH>; // PI9
> +		mosi-gpios = <&pio 8 10 GPIO_ACTIVE_HIGH>; // PI10
> +		cs-gpios = <&pio 8 8 GPIO_ACTIVE_HIGH>; // PI8
> +		num-chipselects = <1>;
> +
> +		panel: panel@0 {
> +			compatible = "anbernic,rg35xx-plus-panel";
> +
> +			reg = <0>;
> +
> +			spi-max-frequency = <3125000>;
> +			spi-3wire;
> +
> +			reset-gpios = <&pio 8 14 GPIO_ACTIVE_LOW>; // PI14
> +
> +			backlight = <&backlight>;

There is no backlight node at this point. Reverse patches 7 and 8 or better yet,
merge them and put patch 8 message into comment to backlight node.

Best regards,
Jernej

> +			power-supply = <&reg_lcd>;
> +
> +			pinctrl-0 = <&lcd0_rgb888_pins>;
> +			pinctrl-names = "default";
> +
> +			port {
> +				panel_in_rgb: endpoint {
> +					remote-endpoint = <&tcon_lcd0_out_lcd>;
> +				};
> +			};
> +		};
> +	};
>  };
>  
>  &codec {
> @@ -187,6 +230,10 @@ &cpu0 {
>  	cpu-supply = <&reg_dcdc1>;
>  };
>  
> +&de {
> +	status = "okay";
> +};
> +
>  &ehci0 {
>  	status = "okay";
>  };
> @@ -206,6 +253,7 @@ &ohci0 {
>  &pio {
>  	vcc-pa-supply = <&reg_cldo3>;
>  	vcc-pc-supply = <&reg_cldo3>;
> +	vcc-pd-supply = <&reg_cldo3>;
>  	vcc-pe-supply = <&reg_cldo3>;
>  	vcc-pf-supply = <&reg_cldo3>;
>  	vcc-pg-supply = <&reg_aldo4>;
> @@ -355,3 +403,13 @@ &usbotg {
>  &usbphy {
>  	status = "okay";
>  };
> +
> +&tcon_lcd0 {
> +	status = "okay";
> +};
> +
> +&tcon_lcd0_out {
> +	tcon_lcd0_out_lcd: endpoint@1 {
> +		remote-endpoint = <&panel_in_rgb>;
> +	};
> +};
>