Re: [PATCH v2 00/14] Expand available features on Qnap TS433

["Heiko Stübner" <heiko@sntech.de>]

Am Dienstag, 23. Juli 2024, 04:57:37 CEST schrieb Rob Herring (Arm):
> 
> On Sun, 21 Jul 2024 19:37:09 +0200, Heiko Stuebner wrote:
> > Thanks to the nicely supported rk3568, the hardest part for adding things,
> > is to pull things from the vendor-kernel and translating them to mainline
> > standards.
> > 
> > This series allows the TS433 to use all 4 bays [0], wiggle some LEDs and
> > access devices connected to all 3 usb ports.
> > 
> > The device runs stable now and might be usable for actual usage.
> > 
> > There is still a todo-list though:
> > - the ethernet mac address for the realtek chip seems correct,
> >   but the gmac0 interface currently uses a wrong one
> > - i2cdetect reports devices on i2c-1 on addresses 54,55,56,57
> >   model_Q0B20_Q0B30_10_10.conf from the original rescue image labels them
> >     VPD_MB = I2C:0x54, VPD_BP = I2C:0x56
> >   the meaning currently being unknown. Some eeprom maybe?
> > - The regulator tree is slightly dubious. Everthing seems to follow rk3568
> >   reference designs, but especially the regulator labeled vcc3v3_sd
> >   seems to supply some PCIe functionality. So I guess the device's
> >   schematics will look quite different than the regulators added to the
> >   vendor devicetree.
> > - Quite a bit of functionality is provided by the MCU connected to uart0.
> >   According to the model.conf there should be fan-control, a number of
> >   additional LEDs (status,locate,usb?)
> > 
> > 
> > Thanks to Qnap engineers adding an easily accessible header for maskrom
> > mode on the board, replacing the bootloader is also quite a breeze. A
> > branch on top of today's u-boot master branch can be found on [1]. I'll
> > submit that code to u-boot once I can cherry-pick the dts patches.
> > 
> > 
> > changes in v2:
> > - add patches for tsadc, gpio-keys, cpu-supply, pmic, gpu and io-domains
> > 
> > 
> > [0] I only have two drives right now, but I tested both the internal
> > sata connector as well as the PCIe connected sata controller in different
> > combinations.
> > [1] https://github.com/mmind/u-boot-rockchip/tree/dev/qnap-ts433/v2024.07
> > 
> > 
> > Heiko Stuebner (14):
> >   arm64: dts: rockchip: add PCIe supply regulator to Qnap-TS433
> >   arm64: dts: rockchip: enable second PCIe controller on the Qnap-TS433
> >   arm64: dts: rockchip: enable uart0 on Qnap-TS433
> >   arm64: dts: rockchip: enable usb ports on Qnap-TS433
> >   arm64: dts: rockchip: add stdout path on Qnap-TS433
> >   arm64: dts: rockchip: enable sata1+2 on Qnap-TS433
> >   arm64: dts: rockchip: add board-aliases for Qnap-TS433
> >   arm64: dts: rockchip: add hdd leds to Qnap-TS433
> >   arm64: dts: rockchip: enable the tsadc on the Qnap-TS433
> >   arm64: dts: rockchip: add gpio-keys to Qnap-TS433
> >   arm64: dts: rockchip: define cpu-supply on the Qnap-TS433
> >   arm64: dts: rockchip: add missing pmic information on Qnap-TS433
> >   arm64: dts: rockchip: enable gpu on Qnap-TS433
> >   arm64: dts: rockchip: add 2 pmu_io_domain supplies for Qnap-TS433
> > 
> >  .../boot/dts/rockchip/rk3568-qnap-ts433.dts   | 539 +++++++++++++++++-
> >  1 file changed, 536 insertions(+), 3 deletions(-)
> > 
> > --
> > 2.39.2
> > 
> > 
> > 
> 
> 
> My bot found new DTB warnings on the .dts files added or changed in this
> series.
> 
> Some warnings may be from an existing SoC .dtsi. Or perhaps the warnings
> are fixed by another series. Ultimately, it is up to the platform
> maintainer whether these warnings are acceptable or not. No need to reply
> unless the platform maintainer has comments.
> 
> If you already ran DT checks and didn't see these error(s), then
> make sure dt-schema is up to date:
> 
>   pip3 install dtschema --upgrade
> 
> 
> New warnings running 'make CHECK_DTBS=y rockchip/rk3568-qnap-ts433.dtb' for 20240721173723.919961-1-heiko@sntech.de:
> 
> arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dtb: sata@fc400000: Unevaluated properties are not allowed ('power-domains' was unexpected)
> 	from schema $id: http://devicetree.org/schemas/ata/rockchip,dwc-ahci.yaml#
> arch/arm64/boot/dts/rockchip/rk3568-qnap-ts433.dtb: sata@fc800000: Unevaluated properties are not allowed ('power-domains' was unexpected)
> 	from schema $id: http://devicetree.org/schemas/ata/rockchip,dwc-ahci.yaml#

fixed (and queued as a fix for 6.11) by:
https://lore.kernel.org/all/20240720205705.776384-1-heiko@sntech.de/