From mboxrd@z Thu Jan 1 00:00:00 1970 From: b.zolnierkie@samsung.com (Bartlomiej Zolnierkiewicz) Date: Mon, 12 Jun 2017 17:54:40 +0200 Subject: [PATCH 3/4 v4] ata: Add driver for Faraday Technology FTIDE010 In-Reply-To: <20170604085009.11902-3-linus.walleij@linaro.org> References: <20170604085009.11902-1-linus.walleij@linaro.org> <20170604085009.11902-3-linus.walleij@linaro.org> Message-ID: <2693110.AQhD5I4g7H@amdc3058> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org On Sunday, June 04, 2017 10:50:08 AM Linus Walleij wrote: > This adds a driver for the Faraday Technology FTIDE010 > PATA IP block. > > When used with the Storlink/Storm/Cortina Systems Gemini > SoC, the PATA interface is accompanied by a PATA<->SATA > bridge, so while the device appear as a PATA controller, > it attaches physically to SATA disks, and also has a > designated memory area with registers to set up the bridge. > > The Gemini SATA bridge is separated into its own driver > file to make things modular and make it possible to reuse > the PATA driver as stand-alone on other systems than the > Gemini. > > dmesg excerpt from the D-Link DIR-685 storage router: > gemini-sata-bridge 46000000.sata: SATA ID 00000e00, PHY ID: 01000100 > gemini-sata-bridge 46000000.sata: set up the Gemini IDE/SATA nexus > ftide010 63000000.ata: set up Gemini PATA0 > ftide010 63000000.ata: device ID 00000500, irq 26, io base 0x63000000 > ftide010 63000000.ata: SATA0 (master) start > gemini-sata-bridge 46000000.sata: SATA0 PHY ready > scsi host0: pata-ftide010 > ata1: PATA max UDMA/133 irq 26 > ata1.00: ATA-8: INTEL SSDSA2CW120G3, 4PC10302, max UDMA/133 > ata1.00: 234441648 sectors, multi 1: LBA48 NCQ (depth 0/32) > ata1.00: configured for UDMA/133 > scsi 0:0:0:0: Direct-Access ATA INTEL SSDSA2CW12 0302 PQ: 0 ANSI: 5 > ata1.00: Enabling discard_zeroes_data > sd 0:0:0:0: [sda] 234441648 512-byte logical blocks: (120 GB/112 GiB) > sd 0:0:0:0: [sda] Write Protect is off > sd 0:0:0:0: [sda] Write cache: enabled, read cache: > enabled, doesn't support DPO or FUA > ata1.00: Enabling discard_zeroes_data > ata1.00: Enabling discard_zeroes_data > sd 0:0:0:0: [sda] Attached SCSI disk > > After this I can flawlessly mount and read/write copy etc files > from /dev/sda[n]. > > Cc: John Feng-Hsin Chiang > Cc: Greentime Hu > Acked-by: Hans Ulli Kroll > Signed-off-by: Linus Walleij Acked-by: Bartlomiej Zolnierkiewicz Thanks for fixing it. Best regards, -- Bartlomiej Zolnierkiewicz Samsung R&D Institute Poland Samsung Electronics