[PATCH 0/3] ARM: dts: sun8i: Support NanoPi SBCs

[PATCH 0/3] ARM: dts: sun8i: Support NanoPi SBCs

[Milo Kim]

NanoPi M1 and NEO have common features, so duplicate properties can be 
moved into new dtsi file.

Milo Kim (3):
  ARM: dts: sun8i: Add common dtsi file for NanoPi SBCs
  ARM: dts: sun8i: Use the common file in NanoPi NEO SBC
  ARM: dts: sun8i: Add dts file for NanoPi M1 SBC

 arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts  |  64 +++++++++++++
 arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts |  79 +----------------
 arch/arm/boot/dts/sun8i-h3-nanopi.dtsi    | 143 ++++++++++++++++++++++++++++++
 3 files changed, 208 insertions(+), 78 deletions(-)
 create mode 100644 arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts
 create mode 100644 arch/arm/boot/dts/sun8i-h3-nanopi.dtsi

-- 
2.9.3

[PATCH 1/3] ARM: dts: sun8i: Add common dtsi file for NanoPi SBCs

[Milo Kim]

This patch provides a common file for NanoPi M1 and Neo SBC.

Those have common features below.
  * UART0
  * 2 LEDs
  * USB host (EHCI3, OHCI3) and PHY
  * MicroSD
  * GPIO key switch

Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
---
 arch/arm/boot/dts/sun8i-h3-nanopi.dtsi | 143 +++++++++++++++++++++++++++++++++
 1 file changed, 143 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun8i-h3-nanopi.dtsi

diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi b/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi
new file mode 100644
index 0000000..e89ca6f
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi
@@ -0,0 +1,143 @@
+/*
+ * Copyright (C) 2016 Milo Kim <woogyom.kim@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+/dts-v1/;
+#include "sun8i-h3.dtsi"
+#include "sunxi-common-regulators.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/sun4i-a10.h>
+
+/ {
+	aliases {
+		serial0 = &uart0;
+	};
+
+	chosen {
+		stdout-path = "serial0:115200n8";
+	};
+
+	leds {
+		compatible = "gpio-leds";
+		pinctrl-names = "default";
+		pinctrl-0 = <&leds_npi>, <&leds_r_npi>;
+
+		status {
+			label = "nanopi:blue:status";
+			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
+			linux,default-trigger = "heartbeat";
+		};
+
+		pwr {
+			label = "nanopi:green:pwr";
+			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
+			default-state = "on";
+		};
+	};
+
+	r_gpio_keys {
+		compatible = "gpio-keys";
+		input-name = "k1";
+		pinctrl-names = "default";
+		pinctrl-0 = <&sw_r_npi>;
+
+		k1 at 0 {
+			label = "k1";
+			linux,code = <KEY_POWER>;
+			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
+		};
+	};
+};
+
+&ehci3 {
+	status = "okay";
+};
+
+&mmc0 {
+	bus-width = <4>;
+	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
+	cd-inverted;
+	pinctrl-names = "default";
+	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
+	status = "okay";
+	vmmc-supply = <&reg_vcc3v3>;
+};
+
+&ohci3 {
+	status = "okay";
+};
+
+&pio {
+	leds_npi: led_pins at 0 {
+		allwinner,pins = "PA10";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+};
+
+&r_pio {
+	leds_r_npi: led_pins at 0 {
+		allwinner,pins = "PL10";
+		allwinner,function = "gpio_out";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+
+	sw_r_npi: key_pins at 0 {
+		allwinner,pins = "PL3";
+		allwinner,function = "gpio_in";
+		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
+		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
+	};
+};
+
+&uart0 {
+	pinctrl-names = "default";
+	pinctrl-0 = <&uart0_pins_a>;
+	status = "okay";
+};
+
+&usbphy {
+	status = "okay";
+};
-- 
2.9.3

[PATCH 1/3] ARM: dts: sun8i: Add common dtsi file for NanoPi SBCs

[Maxime Ripard]

Hi,

On Thu, Oct 20, 2016 at 05:06:59PM +0900, Milo Kim wrote:
> This patch provides a common file for NanoPi M1 and Neo SBC.
> 
> Those have common features below.
>   * UART0
>   * 2 LEDs
>   * USB host (EHCI3, OHCI3) and PHY
>   * MicroSD
>   * GPIO key switch
> 
> Cc: James Pettigrew <james@innovum.com.au>
> Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
> ---
>  arch/arm/boot/dts/sun8i-h3-nanopi.dtsi | 143 +++++++++++++++++++++++++++++++++
>  1 file changed, 143 insertions(+)
>  create mode 100644 arch/arm/boot/dts/sun8i-h3-nanopi.dtsi
> 
> diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi b/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi
> new file mode 100644
> index 0000000..e89ca6f
> --- /dev/null
> +++ b/arch/arm/boot/dts/sun8i-h3-nanopi.dtsi
> @@ -0,0 +1,143 @@
> +/*
> + * Copyright (C) 2016 Milo Kim <woogyom.kim@gmail.com>

This looks like a copy of James' DT. Keeping him as the copyright
holder seems like the right thing to do.

> + *
> + * This file is dual-licensed: you can use it either under the terms
> + * of the GPL or the X11 license, at your option. Note that this dual
> + * licensing only applies to this file, and not this project as a
> + * whole.
> + *
> + *  a) This file is free software; you can redistribute it and/or
> + *     modify it under the terms of the GNU General Public License as
> + *     published by the Free Software Foundation; either version 2 of the
> + *     License, or (at your option) any later version.
> + *
> + *     This file is distributed in the hope that it will be useful,
> + *     but WITHOUT ANY WARRANTY; without even the implied warranty of
> + *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
> + *     GNU General Public License for more details.
> + *
> + * Or, alternatively,
> + *
> + *  b) Permission is hereby granted, free of charge, to any person
> + *     obtaining a copy of this software and associated documentation
> + *     files (the "Software"), to deal in the Software without
> + *     restriction, including without limitation the rights to use,
> + *     copy, modify, merge, publish, distribute, sublicense, and/or
> + *     sell copies of the Software, and to permit persons to whom the
> + *     Software is furnished to do so, subject to the following
> + *     conditions:
> + *
> + *     The above copyright notice and this permission notice shall be
> + *     included in all copies or substantial portions of the Software.
> + *
> + *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
> + *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
> + *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
> + *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
> + *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
> + *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
> + *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
> + *     OTHER DEALINGS IN THE SOFTWARE.
> + */
> +
> +/dts-v1/;
> +#include "sun8i-h3.dtsi"
> +#include "sunxi-common-regulators.dtsi"
> +
> +#include <dt-bindings/gpio/gpio.h>
> +#include <dt-bindings/input/input.h>
> +#include <dt-bindings/pinctrl/sun4i-a10.h>
> +
> +/ {
> +	aliases {
> +		serial0 = &uart0;
> +	};
> +
> +	chosen {
> +		stdout-path = "serial0:115200n8";
> +	};
> +
> +	leds {
> +		compatible = "gpio-leds";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&leds_npi>, <&leds_r_npi>;
> +
> +		status {
> +			label = "nanopi:blue:status";
> +			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>;
> +			linux,default-trigger = "heartbeat";
> +		};
> +
> +		pwr {
> +			label = "nanopi:green:pwr";
> +			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>;
> +			default-state = "on";
> +		};
> +	};
> +
> +	r_gpio_keys {
> +		compatible = "gpio-keys";
> +		input-name = "k1";
> +		pinctrl-names = "default";
> +		pinctrl-0 = <&sw_r_npi>;
> +
> +		k1 at 0 {
> +			label = "k1";
> +			linux,code = <KEY_POWER>;
> +			gpios = <&r_pio 0 3 GPIO_ACTIVE_LOW>;
> +		};
> +	};
> +};
> +
> +&ehci3 {
> +	status = "okay";
> +};
> +
> +&mmc0 {
> +	bus-width = <4>;
> +	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>;
> +	cd-inverted;
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
> +	status = "okay";
> +	vmmc-supply = <&reg_vcc3v3>;
> +};
> +
> +&ohci3 {
> +	status = "okay";
> +};
> +
> +&pio {
> +	leds_npi: led_pins at 0 {
> +		allwinner,pins = "PA10";
> +		allwinner,function = "gpio_out";
> +		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +	};
> +};
> +
> +&r_pio {
> +	leds_r_npi: led_pins at 0 {
> +		allwinner,pins = "PL10";
> +		allwinner,function = "gpio_out";
> +		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +	};
> +
> +	sw_r_npi: key_pins at 0 {
> +		allwinner,pins = "PL3";
> +		allwinner,function = "gpio_in";
> +		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
> +		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
> +	};
> +};
> +
> +&uart0 {
> +	pinctrl-names = "default";
> +	pinctrl-0 = <&uart0_pins_a>;
> +	status = "okay";
> +};
> +
> +&usbphy {
> +	status = "okay";
> +};
> -- 
> 2.9.3
> 

Looks good otherwise.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20161020/d8ce2171/attachment.sig>

[PATCH 1/3] ARM: dts: sun8i: Add common dtsi file for NanoPi SBCs

[Milo Kim]

On 10/21/2016 01:04 AM, Maxime Ripard wrote:
>> + * Copyright (C) 2016 Milo Kim <woogyom.kim@gmail.com>
> This looks like a copy of James' DT. Keeping him as the copyright
> holder seems like the right thing to do.

Oh... thanks for catching this. Sorry to James.

Best regards,
Milo

[PATCH 2/3] ARM: dts: sun8i: Use the common file in NanoPi NEO SBC

[Milo Kim]

Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
---
 arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts | 79 +------------------------------
 1 file changed, 1 insertion(+), 78 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
index 3d64caf..8d2cc6e 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
@@ -40,86 +40,9 @@
  *     OTHER DEALINGS IN THE SOFTWARE.
  */
 
-/dts-v1/;
-#include "sun8i-h3.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include "sun8i-h3-nanopi.dtsi"
 
 / {
 	model = "FriendlyARM NanoPi NEO";
 	compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
-
-	aliases {
-		serial0 = &uart0;
-	};
-
-	chosen {
-		stdout-path = "serial0:115200n8";
-	};
-
-	leds {
-		compatible = "gpio-leds";
-		pinctrl-names = "default";
-		pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
-
-		pwr {
-			label = "nanopi:green:pwr";
-			gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
-			default-state = "on";
-		};
-
-		status {
-			label = "nanopi:blue:status";
-			gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
-		};
-	};
-};
-
-&ehci3 {
-	status = "okay";
-};
-
-&mmc0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
-	vmmc-supply = <&reg_vcc3v3>;
-	bus-width = <4>;
-	cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
-	cd-inverted;
-	status = "okay";
-};
-
-&ohci3 {
-	status = "okay";
-};
-
-&pio {
-	leds_opc: led-pins {
-		allwinner,pins = "PA10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-};
-
-&r_pio {
-	leds_r_opc: led-pins {
-		allwinner,pins = "PL10";
-		allwinner,function = "gpio_out";
-		allwinner,drive = <SUN4I_PINCTRL_10_MA>;
-		allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
-	};
-};
-
-&uart0 {
-	pinctrl-names = "default";
-	pinctrl-0 = <&uart0_pins_a>;
-	status = "okay";
-};
-
-&usbphy {
-	/* USB VBUS is always on */
-	status = "okay";
 };
-- 
2.9.3

[PATCH 2/3] ARM: dts: sun8i: Use the common file in NanoPi NEO SBC

[Maxime Ripard]

Hi Milo,

On Thu, Oct 20, 2016 at 05:07:00PM +0900, Milo Kim wrote:
> Cc: James Pettigrew <james@innovum.com.au>
> Signed-off-by: Milo Kim <woogyom.kim@gmail.com>

Please add a commit log.

Thanks!
Maxime

-- 
Maxime Ripard, Free Electrons
Embedded Linux and Kernel engineering
http://free-electrons.com
-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 801 bytes
Desc: not available
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20161020/eb5b7b81/attachment.sig>

[PATCH 3/3] ARM: dts: sun8i: Add dts file for NanoPi M1 SBC

[Milo Kim]

NanoPi M1 is the Allwinner H3 based board.
This patch enables UART for debug console, LEDs, GPIO key switch, 3 USB
host ports, a micro SD slot and related power and pin controls.

Cc: James Pettigrew <james@innovum.com.au>
Signed-off-by: Milo Kim <woogyom.kim@gmail.com>
---
 arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts | 64 ++++++++++++++++++++++++++++++++
 1 file changed, 64 insertions(+)
 create mode 100644 arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts

diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts
new file mode 100644
index 0000000..ec63d10
--- /dev/null
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-m1.dts
@@ -0,0 +1,64 @@
+/*
+ * Copyright (C) 2016 Milo Kim <woogyom.kim@gmail.com>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ *  a) This file is free software; you can redistribute it and/or
+ *     modify it under the terms of the GNU General Public License as
+ *     published by the Free Software Foundation; either version 2 of the
+ *     License, or (at your option) any later version.
+ *
+ *     This file is distributed in the hope that it will be useful,
+ *     but WITHOUT ANY WARRANTY; without even the implied warranty of
+ *     MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE.  See the
+ *     GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ *  b) Permission is hereby granted, free of charge, to any person
+ *     obtaining a copy of this software and associated documentation
+ *     files (the "Software"), to deal in the Software without
+ *     restriction, including without limitation the rights to use,
+ *     copy, modify, merge, publish, distribute, sublicense, and/or
+ *     sell copies of the Software, and to permit persons to whom the
+ *     Software is furnished to do so, subject to the following
+ *     conditions:
+ *
+ *     The above copyright notice and this permission notice shall be
+ *     included in all copies or substantial portions of the Software.
+ *
+ *     THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ *     EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ *     OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ *     NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ *     HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ *     WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ *     FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ *     OTHER DEALINGS IN THE SOFTWARE.
+ */
+
+#include "sun8i-h3-nanopi.dtsi"
+
+/ {
+	model = "FriendlyArm NanoPi M1";
+	compatible = "friendlyarm,nanopi-m1", "allwinner,sun8i-h3";
+};
+
+&ehci1 {
+	status = "okay";
+};
+
+&ehci2 {
+	status = "okay";
+};
+
+&ohci1 {
+	status = "okay";
+};
+
+&ohci2 {
+	status = "okay";
+};
-- 
2.9.3