From: Roger Quadros <rogerq@kernel.org>
To: Jayesh Choudhary <j-choudhary@ti.com>, nm@ti.com, vigneshr@ti.com
Cc: s-vadapalli@ti.com, afd@ti.com, kristo@kernel.org,
robh+dt@kernel.org, krzysztof.kozlowski+dt@linaro.org,
conor+dt@kernel.org, a-bhatia1@ti.com, r-ravikumar@ti.com,
sabiya.d@ti.com, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org,
linux-arm-kernel@lists.infradead.org
Subject: Re: [PATCH v8 3/5] arm64: dts: ti: k3-j784s4-main: Add DSS and DP-bridge node
Date: Tue, 1 Aug 2023 19:50:21 +0300 [thread overview]
Message-ID: <390ef20d-a225-e7cb-73bd-9ba8c1985a98@kernel.org> (raw)
In-Reply-To: <20230801070019.219660-4-j-choudhary@ti.com>
On 01/08/2023 10:00, Jayesh Choudhary wrote:
> From: Rahul T R <r-ravikumar@ti.com>
>
> Add DSS and DP-bridge node for J784S4 SoC. DSS IP in J784S4 is
> same as DSS IP in J721E, so same compatible is being used.
> The DP is Cadence MHDP8546.
>
> Signed-off-by: Rahul T R <r-ravikumar@ti.com>
> [j-choudhary@ti.com: move dss & mhdp node together in main, fix dss node]
> Signed-off-by: Jayesh Choudhary <j-choudhary@ti.com>
> ---
> arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi | 73 ++++++++++++++++++++++
> 1 file changed, 73 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> index fbf5ab94d785..975661948755 100644
> --- a/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> +++ b/arch/arm64/boot/dts/ti/k3-j784s4-main.dtsi
> @@ -1749,4 +1749,77 @@ c71_3: dsp@67800000 {
> resets = <&k3_reset 40 1>;
> firmware-name = "j784s4-c71_3-fw";
> };
> +
> + mhdp: dp-bridge@a000000 {
bridge@a000000
> + compatible = "ti,j721e-mhdp8546";
> +
why the new lines all over the place within nodes?
> + reg = <0x0 0xa000000 0x0 0x30a00>,
> + <0x0 0x4f40000 0x0 0x20>;
> + reg-names = "mhdptx", "j721e-intg";
> +
> + clocks = <&k3_clks 217 11>;
> +
> + interrupt-parent = <&gic500>;
> + interrupts = <GIC_SPI 614 IRQ_TYPE_LEVEL_HIGH>;
> +
> + power-domains = <&k3_pds 217 TI_SCI_PD_EXCLUSIVE>;
> +
> + status = "disabled";
> +
> + dp0_ports: ports {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + };
> + };
> +
> + dss: dss@4a00000 {
> + compatible = "ti,j721e-dss";
> + reg = <0x00 0x04a00000 0x00 0x10000>, /* common_m */
> + <0x00 0x04a10000 0x00 0x10000>, /* common_s0*/
> + <0x00 0x04b00000 0x00 0x10000>, /* common_s1*/
> + <0x00 0x04b10000 0x00 0x10000>, /* common_s2*/
> + <0x00 0x04a20000 0x00 0x10000>, /* vidl1 */
> + <0x00 0x04a30000 0x00 0x10000>, /* vidl2 */
> + <0x00 0x04a50000 0x00 0x10000>, /* vid1 */
> + <0x00 0x04a60000 0x00 0x10000>, /* vid2 */
> + <0x00 0x04a70000 0x00 0x10000>, /* ovr1 */
> + <0x00 0x04a90000 0x00 0x10000>, /* ovr2 */
> + <0x00 0x04ab0000 0x00 0x10000>, /* ovr3 */
> + <0x00 0x04ad0000 0x00 0x10000>, /* ovr4 */
> + <0x00 0x04a80000 0x00 0x10000>, /* vp1 */
> + <0x00 0x04aa0000 0x00 0x10000>, /* vp1 */
> + <0x00 0x04ac0000 0x00 0x10000>, /* vp1 */
> + <0x00 0x04ae0000 0x00 0x10000>, /* vp4 */
> + <0x00 0x04af0000 0x00 0x10000>; /* wb */
> +
> + reg-names = "common_m", "common_s0",
> + "common_s1", "common_s2",
> + "vidl1", "vidl2","vid1","vid2",
> + "ovr1", "ovr2", "ovr3", "ovr4",
> + "vp1", "vp2", "vp3", "vp4",
> + "wb";
> +
> + clocks = <&k3_clks 218 0>,
> + <&k3_clks 218 2>,
> + <&k3_clks 218 5>,
> + <&k3_clks 218 14>,
> + <&k3_clks 218 18>;
> + clock-names = "fck", "vp1", "vp2", "vp3", "vp4";
> +
> + power-domains = <&k3_pds 218 TI_SCI_PD_EXCLUSIVE>;
> +
> + interrupts = <GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 603 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 604 IRQ_TYPE_LEVEL_HIGH>,
> + <GIC_SPI 605 IRQ_TYPE_LEVEL_HIGH>;
> + interrupt-names = "common_m",
> + "common_s0",
> + "common_s1",
> + "common_s2";
> +
> + status = "disabled";
> +
> + dss_ports: ports {
> + };
> + };
> };
--
cheers,
-roger
_______________________________________________
linux-arm-kernel mailing list
linux-arm-kernel@lists.infradead.org
http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
next prev parent reply other threads:[~2023-08-01 16:51 UTC|newest]
Thread overview: 14+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-08-01 7:00 [PATCH v8 0/5] Enable Display for J784S4 and AM69-SK platform Jayesh Choudhary
2023-08-01 7:00 ` [PATCH v8 1/5] arm64: dts: ti: k3-j784s4-main: Add system controller and SERDES lane mux Jayesh Choudhary
2023-08-01 14:19 ` Andrew Davis
2023-08-01 7:00 ` [PATCH v8 2/5] arm64: dts: ti: k3-j784s4-main: Add WIZ and SERDES PHY nodes Jayesh Choudhary
2023-08-01 16:56 ` Roger Quadros
2023-08-03 5:37 ` Jayesh Choudhary
2023-08-01 7:00 ` [PATCH v8 3/5] arm64: dts: ti: k3-j784s4-main: Add DSS and DP-bridge node Jayesh Choudhary
2023-08-01 16:50 ` Roger Quadros [this message]
2023-08-01 7:00 ` [PATCH v8 4/5] arm64: dts: ti: k3-j784s4-evm: Enable DisplayPort-0 Jayesh Choudhary
2023-08-01 16:40 ` Roger Quadros
2023-08-01 7:00 ` [PATCH v8 5/5] arm64: dts: ti: k3-am69-sk: Add DP and HDMI support Jayesh Choudhary
2023-08-01 16:48 ` Roger Quadros
2023-08-01 16:58 ` Roger Quadros
2023-08-03 5:26 ` Jayesh Choudhary
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=390ef20d-a225-e7cb-73bd-9ba8c1985a98@kernel.org \
--to=rogerq@kernel.org \
--cc=a-bhatia1@ti.com \
--cc=afd@ti.com \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=j-choudhary@ti.com \
--cc=kristo@kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
--cc=linux-kernel@vger.kernel.org \
--cc=nm@ti.com \
--cc=r-ravikumar@ti.com \
--cc=robh+dt@kernel.org \
--cc=s-vadapalli@ti.com \
--cc=sabiya.d@ti.com \
--cc=vigneshr@ti.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).