From: mcuelenaere@gmail.com (Maurus Cuelenaere)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 4/4] sdhci-s3c: add regulator support
Date: Wed, 28 Jul 2010 16:48:06 +0200 [thread overview]
Message-ID: <4C504326.30708@gmail.com> (raw)
In-Reply-To: <1280326797-15792-5-git-send-email-m.szyprowski@samsung.com>
Op 28-07-10 16:19, Marek Szyprowski schreef:
> This patch adds support for regulator API to sdhci-s3c driver. Regulators
> can be used to disable power in suspended state to reduce dissipated
> energy.
I'm not sure about this, when I would try to do this I'd look at implementing
this in the sdhci driver itself instead of a subdriver of it.
> Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
> drivers/mmc/host/sdhci-s3c.c | 30 +++++++++++++++++++++++++++++-
> 1 files changed, 29 insertions(+), 1 deletions(-)
>
> diff --git a/drivers/mmc/host/sdhci-s3c.c b/drivers/mmc/host/sdhci-s3c.c
> index 606e695..b9d46a5 100644
> --- a/drivers/mmc/host/sdhci-s3c.c
> +++ b/drivers/mmc/host/sdhci-s3c.c
> @@ -19,6 +19,7 @@
> #include <linux/clk.h>
> #include <linux/io.h>
> #include <linux/gpio.h>
> +#include <linux/regulator/consumer.h>
>
> #include <linux/mmc/host.h>
>
> @@ -50,6 +51,7 @@ struct sdhci_s3c {
>
> struct clk *clk_io;
> struct clk *clk_bus[MAX_BUS_CLK];
> + struct regulator *vmmc;
> };
>
> static inline struct sdhci_s3c *to_s3c(struct sdhci_host *host)
> @@ -309,6 +311,13 @@ static int __devinit sdhci_s3c_probe(struct platform_device *pdev)
>
> platform_set_drvdata(pdev, host);
>
> + sc->vmmc = regulator_get(dev, "vmmc");
> + if (IS_ERR(sc->vmmc)) {
> + dev_warn(dev, "no vmmc regulator found\n");
> + sc->vmmc = NULL;
> + } else
> + regulator_enable(sc->vmmc);
> +
> sc->clk_io = clk_get(dev, "hsmmc");
> if (IS_ERR(sc->clk_io)) {
> dev_err(dev, "failed to get io clock\n");
> @@ -482,6 +491,11 @@ static int __devexit sdhci_s3c_remove(struct platform_device *pdev)
> clk_disable(sc->clk_io);
> clk_put(sc->clk_io);
>
> + if (sc->vmmc) {
> + regulator_disable(sc->vmmc);
> + regulator_put(sc->vmmc);
> + }
> +
> iounmap(host->ioaddr);
> release_resource(sc->ioarea);
> kfree(sc->ioarea);
> @@ -496,15 +510,29 @@ static int __devexit sdhci_s3c_remove(struct platform_device *pdev)
>
> static int sdhci_s3c_suspend(struct platform_device *dev, pm_message_t pm)
> {
> + int ret = 0;
> struct sdhci_host *host = platform_get_drvdata(dev);
> + struct sdhci_s3c *sc = sdhci_priv(host);
>
> sdhci_suspend_host(host, pm);
> - return 0;
> +
> + if (sc->vmmc)
> + ret = regulator_disable(sc->vmmc);
> +
> + return ret;
> }
>
> static int sdhci_s3c_resume(struct platform_device *dev)
> {
> struct sdhci_host *host = platform_get_drvdata(dev);
> + struct sdhci_s3c *sc = sdhci_priv(host);
> +
> + if (sc->vmmc) {
> + int ret = regulator_disable(sc->vmmc);
> + if (ret)
> + return ret;
> + mdelay(2);
Shouldn't these delays be handled in the regulator framework itself?
> + }
>
> sdhci_resume_host(host);
> return 0;
--
Maurus Cuelenaere
next prev parent reply other threads:[~2010-07-28 14:48 UTC|newest]
Thread overview: 17+ messages / expand[flat|nested] mbox.gz Atom feed top
2010-07-28 14:19 [PATCH] SDHCI-S3C updates Marek Szyprowski
2010-07-28 14:19 ` [PATCHv2 1/4] sdhci-s3c: add support for the non standard minimal clock value Marek Szyprowski
2010-07-28 16:48 ` Ben Dooks
2010-07-29 5:30 ` Marek Szyprowski
2010-07-28 14:19 ` [PATCH 2/4] sdhci-s3c: enable SDHCI_QUIRK_NO_HISPD_BIT quirk Marek Szyprowski
2010-07-28 14:19 ` [PATCHv5 3/4] sdhci-s3c: add support for new card detection methods (driver part) Marek Szyprowski
2010-07-28 14:39 ` Maurus Cuelenaere
2010-07-29 5:22 ` Marek Szyprowski
2010-07-28 17:03 ` Ben Dooks
2010-07-29 5:40 ` Marek Szyprowski
2010-07-28 14:19 ` [PATCH 4/4] sdhci-s3c: add regulator support Marek Szyprowski
2010-07-28 14:48 ` Maurus Cuelenaere [this message]
2010-07-28 15:41 ` Mark Brown
2010-07-28 17:06 ` Maurus Cuelenaere
2010-07-28 17:14 ` Mark Brown
2010-07-29 5:28 ` Marek Szyprowski
2010-07-28 17:39 ` Mark Brown
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4C504326.30708@gmail.com \
--to=mcuelenaere@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).