GPMI-NAND Status?

[b32955@freescale.com (Huang Shijie)]

Hi Koen:
thanks for your test.
> Hi,
>
>
>
> On Tue, Aug 9, 2011 at 8:36 AM, Huang Shijie<b32955@freescale.com>  wrote:
>> Hi Koen:
>>> Hi,
>>>
>>> On Mon, Aug 8, 2011 at 12:37 PM, Huang Shijie<b32955@freescale.com>
>>>   wrote:
>>>> Hi,
>>>>> On my target, the mxs-dma is working for sdio until the gpmi-nand
>>>>> gives a timeout. After that the dma for sdio is *not fully* working
>>>>> anymore.
>>>>>
>>>> We need more log in following aspects:
>>>> [1] apbh-dma registers
>>>> [2] clk registers
>>>> [3] gpmi registers
>>>>
>>>> Please git-apply the patch in the attachment.
>>>> It will print out more DMA information WHEN dma-timeout occur.
>>> Don't get it. What exactly are you trying to dump?
>>> This patch dumps CTRL0, CTRL1, CTRL2, DEVSEL but also some registers
>>> of APBH channel0 which is reserved....
>> sorry, I intended to print out the channel 4(NAND_DEVICE0).
>>
>> I want to know that:
>>   When the dma timeout occurs, whether it caused by the GPMI or by the DMA
>> itself.
> Ok, I was a little confused about the addresses, but it seems like you
> are using mx28 (and corresponding addresses). APBH dma for mx23 has
> different address according to the datasheet.
> So I adjusted the patch a little for mx23, see attachment.
>
you are right. My address was wrong.
> Here is the log with some comments added on the dma.
>
> # ubiformat /dev/mtd1
> ubiformat: mtd1 (nand), size 20971520 bytes (20.0 MiB), 40 eraseblocks
> of 524288 bytes (512.0 KiB), min. I/O size 4096 bytes
> libscan: scanning eraseblock 0 --  2 % complete  [   86.720000] [
> start_dma_without_bch_irq : 393 ] DMA timeout, last DMA :1
> [   86.720000] ------------------------DMA DUMP BEGIN ----------
> [   86.730000] APBH REG :0 : 30000000   // ->  HW_APBH_CTRL0:
> AHB_BURST8_EN, APB_BURST4_EN
> [   86.730000] APBH REG :10 : 00FF0000   // ->  HW_APBH_CTRL1:
> CHX_CMDCMPLT_IRQ_EN, no cmdcmplt_irq
> [   86.740000] APBH REG :20 : 00000000   // ->  HW_APBH_CTRL2: no error_irq
> [   86.740000] APBH REG :30 : 00000000   // ->  HW_APBH_DEVSEL: "N/A
> for apbh bridge dma."
> [   86.750000] APBH CH4 REG :200 : 418D7098 // executing last dma
> command of command chain (see below)
> [   86.750000] APBH CH4 REG :210 : 00000000 // no next command, ok
> [   86.750000] APBH CH4 REG :220 : 000001C8 // HW_APBH_CH4_CMD:
> COMMAND = NO DMA TRANSFER, IRQONCMPLT, WAIT4ENDCMD, SEMAPHORE,
> HALTONTERMINATE
> [   86.760000] APBH CH4 REG :230 : 00000000 // HW_APBH_CH4_BAR:
> "Address of system memory buffer to be read or written over the AHB
> bus." ->  strange value ...
> [   86.760000] APBH CH4 REG :240 : 00010000 // HW_APBH_CH4_SEMA:
> semaphore counter is 1
> [   86.770000] APBH CH4 REG :250 : 03A00015 // HW_APBH_CH4_DEBUG1:
> LOCK, NEXTCMDADDRVALID, RD_FIFO_EMPTY, WR_FIFO_EMPTY,  STATEMACHINE =
> "WAIT_END = 0x15 When the Wait for Command End bit is set, the state
> machine enters this state until the DMA device indicates that the
> command is complete."
> [   86.770000] APBH CH4 REG :260 : 00000000 // ->  HW_APBH_CH4_DEBUG2:
> no apb of ahb bytes remaining for transfer
> [   86.780000] [ 0 ] : ME : 418d7000, next : 418d704c, bits :
> 00002304, bytes : 00000000, buf : 00000000
> [   86.790000] [ 0 ] PIO[0] : 03800000
> [   86.790000] [ 0 ] PIO[1] : 00000000
> [   86.800000] [ 0 ] PIO[2] : 00000000
> [   86.800000] [ 1 ] : ME : 418d704c, next : 418d7098, bits :
> 00006304, bytes : 00000001, buf : 4181b000
> [   86.810000] [ 1 ] PIO[0] : 018010da
> [   86.810000] [ 1 ] PIO[1] : 00000000
> [   86.820000] [ 1 ] PIO[2] : 000011ff
> [   86.820000] [ 2 ] : ME : 418d7098, next : 00000000, bits :
It hungs here.

> 000023c8, bytes : 00000000, buf : 00000000
> [   86.830000] [ 2 ] PIO[0] : 038010da
> [   86.840000] [ 2 ] PIO[1] : 00000000
> [   86.840000] [ 2 ] PIO[2] : 00000000
> [   86.840000] ------------------------DMA DUMP END ------------
> [   86.850000] [ gpmi_show_regs : 076 ] -------------- Show GPMI
> registers ----------
> [   86.860000] [ gpmi_show_regs : 079 ] offset 0x000 : 0x238010da
> [   86.870000] [ gpmi_show_regs : 079 ] offset 0x010 : 0x00000000
> [   86.870000] [ gpmi_show_regs : 079 ] offset 0x020 : 0x000011ff
> [   86.880000] [ gpmi_show_regs : 079 ] offset 0x030 : 0x000010da
> [   86.890000] [ gpmi_show_regs : 079 ] offset 0x040 : 0x40f0c480
> [   86.890000] [ gpmi_show_regs : 079 ] offset 0x050 : 0x40f09000
> [   86.900000] [ gpmi_show_regs : 079 ] offset 0x060 : 0x0004000c
> [   86.910000] [ gpmi_show_regs : 079 ] offset 0x070 : 0x00010203
> [   86.910000] [ gpmi_show_regs : 079 ] offset 0x080 : 0x05000000
> [   86.920000] [ gpmi_show_regs : 079 ] offset 0x090 : 0x09020101
> [   86.920000] [ gpmi_show_regs : 079 ] offset 0x0a0 : 0x00000030
> [   86.930000] [ gpmi_show_regs : 079 ] offset 0x0b0 : 0x80000010
> [   86.940000] [ gpmi_show_regs : 079 ] offset 0x0c0 : 0x100000ba
> [   86.940000] [ gpmi_show_regs : 079 ] offset 0x0d0 : 0x03000000
> [   86.950000] [ gpmi_show_regs : 081 ] -------------- Show GPMI
> registers end ----------
> [   86.960000] Kernel panic - not syncing: -----------DMA
> FAILED------------------
Please post the functions-calling stack when the panic occurs.
I also want to know where the code is running when the time-out occur.

My gmail is shijie8 at gmail.com
We may talk more on the gtalk.

Best Regards
Huang Shijie

> Br,
> Koen
>
>>
>> Please try the new patch.
>>
>> Best Regards
>> Huang Shijie
>>> Then it prints some debug info on channel 1 (ssp1) and then alle
>>> channel 2 register except the debug register (ssp2 = not used here).
>>>
>>> What info do you need?
>>>
>>> Br,
>>> Koen
>>>
>>>> Best Regards
>>>> Huang Shijie
>>>>
>>> _______________________________________________
>>> linux-arm-kernel mailing list
>>> linux-arm-kernel at lists.infradead.org
>>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
>>
>>