From mboxrd@z Thu Jan 1 00:00:00 1970 From: br@pwrnet.de (Bernhard Roth) Date: Mon, 15 Aug 2011 16:28:15 +0200 Subject: [PATCH] atmel_serial: RS485: receiving enabled when sending data Message-ID: <4E492CFF.7040905@pwrnet.de> To: linux-arm-kernel@lists.infradead.org List-Id: linux-arm-kernel.lists.infradead.org Hello! By default the atmel_serial driver in RS485 mode disables receiving data until all data in the send buffer has been sent. This flag allows to receive data even whilst sending data. This is very useful to - check if the data has been sent correctly over the RS485 bus - assure that no collision happened - check for short circuits/termination issues on the RS485 bus Usually this functionality is realized by hardware, wether controlling the RX-Enable pin of the RS485 transceiver with RTS (driver control signal) or pulling it LOW permanently. The present atmel_serial driver makes this impossible, thus requiring following patch. Usage example: struct serial_rs485 rs485; memset(&rs485, 0, sizeof(rs485)); rs485.flags = SER_RS485_ENABLED | SER_RS485_RX_DURING_TX; ioctl(fd, TIOCSRS485, &rs485); atmel_serial: RS485: receiving enabled when sending data By default the atmel_serial driver in RS485 mode disables receiving data until all data in the send buffer has been sent. This flag allows to receive data even whilst sending data. Signed-off-by: Bernhard Roth Signed-off-by: Claudio Scordino --- drivers/tty/serial/atmel_serial.c | 17 ++++++++++------- include/linux/serial.h | 1 + 2 files changed, 11 insertions(+), 7 deletions(-) diff --git a/drivers/tty/serial/atmel_serial.c b/drivers/tty/serial/atmel_serial.c index af9b781..5f6c745 100644 --- a/drivers/tty/serial/atmel_serial.c +++ b/drivers/tty/serial/atmel_serial.c @@ -339,8 +339,9 @@ static void atmel_stop_tx(struct uart_port *port) /* Disable interrupts */ UART_PUT_IDR(port, atmel_port->tx_done_mask); - if (atmel_port->rs485.flags & SER_RS485_ENABLED) - atmel_start_rx(port); + if ((atmel_port->rs485.flags & SER_RS485_ENABLED) && + !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX)) + atmel_start_rx(port); } /* @@ -356,8 +357,9 @@ static void atmel_start_tx(struct uart_port *port) really need this.*/ return; - if (atmel_port->rs485.flags & SER_RS485_ENABLED) - atmel_stop_rx(port); + if ((atmel_port->rs485.flags & SER_RS485_ENABLED) && + !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX)) + atmel_stop_rx(port); /* re-enable PDC transmit */ UART_PUT_PTCR(port, ATMEL_PDC_TXTEN); @@ -680,9 +682,10 @@ static void atmel_tx_dma(struct uart_port *port) /* Enable interrupts */ UART_PUT_IER(port, atmel_port->tx_done_mask); } else { - if (atmel_port->rs485.flags & SER_RS485_ENABLED) { - /* DMA done, stop TX, start RX for RS485 */ - atmel_start_rx(port); + if ((atmel_port->rs485.flags & SER_RS485_ENABLED) && + !(atmel_port->rs485.flags & SER_RS485_RX_DURING_TX)) { + /* DMA done, stop TX, start RX for RS485 */ + atmel_start_rx(port); } } diff --git a/include/linux/serial.h b/include/linux/serial.h index ef91406..97ff8e2 100644 --- a/include/linux/serial.h +++ b/include/linux/serial.h @@ -211,6 +211,7 @@ struct serial_rs485 { #define SER_RS485_RTS_ON_SEND (1 << 1) #define SER_RS485_RTS_AFTER_SEND (1 << 2) #define SER_RS485_RTS_BEFORE_SEND (1 << 3) +#define SER_RS485_RX_DURING_TX (1 << 4) __u32 delay_rts_before_send; /* Milliseconds */ __u32 delay_rts_after_send; /* Milliseconds */ __u32 padding[5]; /* Memory is cheap, new structs -- 1.7.1