From: nicolas.ferre@atmel.com (Nicolas Ferre)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] net/macb: add DT support
Date: Fri, 02 Dec 2011 18:53:58 +0100 [thread overview]
Message-ID: <4ED910B6.7080000@atmel.com> (raw)
In-Reply-To: <20111202172854.GB4998@totoro>
On 12/02/2011 06:28 PM, Jamie Iles :
> Hi Nicolas,
>
> On Fri, Dec 02, 2011 at 06:14:10PM +0100, Nicolas Ferre wrote:
>> From: Jean-Christophe PLAGNIOL-VILLARD<plagnioj@jcrosoft.com>
>>
>> Allow the device tree to provide the mac address and the phy mode.
>>
>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD<plagnioj@jcrosoft.com>
>> [nicolas.ferre at atmel.com: change "compatible" node property, doc and DT hwaddr]
>> Signed-off-by: Nicolas Ferre<nicolas.ferre@atmel.com>
>> Cc: Jamie Iles<jamie@jamieiles.com>
>
> Looks nice to me. There's a patch below to add the GEM stuff to the
> binding too if you want to role that in.
Yes, I will push it in a "v3" (I was busy correcting a bug and did not
see your answer before sending v2...).
> Acked-by: Jamie Iles<jamie@jamieiles.com>
>
> 8<----
>
> diff --git a/Documentation/devicetree/bindings/net/macb.txt b/Documentation/devicetree/bindings/net/macb.txt
> index 7f0b90a..e09e3fb 100644
> --- a/Documentation/devicetree/bindings/net/macb.txt
> +++ b/Documentation/devicetree/bindings/net/macb.txt
> @@ -1,9 +1,11 @@
> -* Cadence MACB Ethernet controller
> +* Cadence MACB/GEM Ethernet controller
>
> Required properties:
> -- compatible: Should be "cdns,[<chip>-]macb"
> +- compatible: Should be "cdns,[<chip>-]{macb,gem}"
> Use "cdns,at91sam9260-macb" Atmel at91sam9260 and at91sam9263 SoCs.
> Use "cdns,at32ap7000-macb" for other 10/100 usage or use the generic form: "cdns,macb"
> + Use "cnds,pc302-gem" for Picochip picoXcell pc302 and later devices based on
> + the Cadence GEM, or the generic form "cdns,gem".
> - reg: Address and length of the register set for the device
> - interrupts: Should contain macb interrupt
> - phy-mode: String, operation mode of the PHY interface.
> diff --git a/drivers/net/ethernet/cadence/macb.c b/drivers/net/ethernet/cadence/macb.c
> index 103c6e6..89060e6 100644
> --- a/drivers/net/ethernet/cadence/macb.c
> +++ b/drivers/net/ethernet/cadence/macb.c
> @@ -1247,6 +1247,8 @@ static const struct of_device_id macb_dt_ids[] = {
> { .compatible = "cdns,at32ap7000-macb" },
> { .compatible = "cdns,at91sam9260-macb" },
> { .compatible = "cdns,macb" },
> + { .compatible = "cdns,pc302-gem" },
> + { .compatible = "cdns,gem" },
> { /* sentinel */ }
> };
BTW, I think we may also modify the MII/RMII selection code for adding
gigabit selection... but maybe you already have the patches?
Best regards,
--
Nicolas Ferre
next prev parent reply other threads:[~2011-12-02 17:53 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
[not found] <20111202153832.GA4998@totoro>
2011-12-02 17:14 ` [PATCH] net/macb: add DT support Nicolas Ferre
2011-12-02 17:28 ` Jamie Iles
2011-12-02 17:53 ` Nicolas Ferre [this message]
2011-12-05 11:48 ` Jamie Iles
2011-12-05 11:51 ` Nicolas Ferre
2011-12-02 17:43 ` [PATCH v2] " Nicolas Ferre
2011-12-02 17:50 ` [PATCH] ARM: at91/net: add macb ethernet controller in 9g45 DT Nicolas Ferre
2011-12-03 5:56 ` Jean-Christophe PLAGNIOL-VILLARD
2011-12-05 11:39 ` Nicolas Ferre
2011-12-02 17:58 ` [PATCH v2] net/macb: add DT support David Miller
2011-12-05 11:36 ` Nicolas Ferre
2011-12-05 11:59 ` [PATCH v3 1/2] net/macb: add DT support for Cadence macb/gem driver Nicolas Ferre
2011-12-05 11:59 ` [PATCH v3 2/2] ARM: at91/net: add macb ethernet controller in 9g45 DT Nicolas Ferre
2011-12-05 15:25 ` Jean-Christophe PLAGNIOL-VILLARD
2011-12-07 13:49 ` [PATCH v3 1/2] net/macb: add DT support for Cadence macb/gem driver Nicolas Ferre
2011-12-07 18:27 ` David Miller
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4ED910B6.7080000@atmel.com \
--to=nicolas.ferre@atmel.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).