From: robherring2@gmail.com (Rob Herring)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2] gpio: pl061: convert to use generic irq chip
Date: Mon, 02 Jan 2012 10:54:36 -0600 [thread overview]
Message-ID: <4F01E14C.9010407@gmail.com> (raw)
In-Reply-To: <20120102085433.GJ18381@ponder.secretlab.ca>
Grant,
On 01/02/2012 02:54 AM, Grant Likely wrote:
> On Mon, Dec 19, 2011 at 02:52:07PM -0600, Rob Herring wrote:
>> From: Rob Herring <rob.herring@calxeda.com>
>>
>> Convert the pl061 irq_chip code to use the generic irq chip code.
>>
>> This has the side effect of using 32-bit accesses rather than 8-bit
>> accesses to interrupt registers. The h/w TRM and testing seem to indicate
>> this is fine.
>>
>> Signed-off-by: Rob Herring <rob.herring@calxeda.com>
>> Acked-by: Grant Likely <grant.likely@secretlab.ca>
>> Cc: Linus Walleij <linus.ml.walleij@gmail.com>
>
> What does this apply against? It doesn't apply cleanly.
>
You need the whole series which is available here:
git://sources.calxeda.com/kernel/linux.git pl061-domain-v2
Rob
> g.
>
>> ---
>> v2:
>> - put struct irq_chip_generic pointer into struct pl061_gpio instead of domain
>> ptr.
>>
>> drivers/gpio/Kconfig | 1 +
>> drivers/gpio/gpio-pl061.c | 74 ++++++++++++++++-----------------------------
>> 2 files changed, 27 insertions(+), 48 deletions(-)
>>
>> diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig
>> index 8482a23..4d433e2 100644
>> --- a/drivers/gpio/Kconfig
>> +++ b/drivers/gpio/Kconfig
>> @@ -138,6 +138,7 @@ config GPIO_MXS
>> config GPIO_PL061
>> bool "PrimeCell PL061 GPIO support"
>> depends on ARM_AMBA
>> + select GENERIC_IRQ_CHIP
>> help
>> Say yes here to support the PrimeCell PL061 GPIO device
>>
>> diff --git a/drivers/gpio/gpio-pl061.c b/drivers/gpio/gpio-pl061.c
>> index fe19dec..96ff6b2 100644
>> --- a/drivers/gpio/gpio-pl061.c
>> +++ b/drivers/gpio/gpio-pl061.c
>> @@ -50,10 +50,10 @@ struct pl061_gpio {
>> * the IRQ code simpler.
>> */
>> spinlock_t lock; /* GPIO registers */
>> - spinlock_t irq_lock; /* IRQ registers */
>>
>> void __iomem *base;
>> int irq_base;
>> + struct irq_chip_generic *irq_gc;
>> struct gpio_chip gc;
>> };
>>
>> @@ -125,40 +125,10 @@ static int pl061_to_irq(struct gpio_chip *gc, unsigned offset)
>> return chip->irq_base + offset;
>> }
>>
>> -/*
>> - * PL061 GPIO IRQ
>> - */
>> -static void pl061_irq_disable(struct irq_data *d)
>> -{
>> - struct pl061_gpio *chip = irq_data_get_irq_chip_data(d);
>> - int offset = d->irq - chip->irq_base;
>> - unsigned long flags;
>> - u8 gpioie;
>> -
>> - spin_lock_irqsave(&chip->irq_lock, flags);
>> - gpioie = readb(chip->base + GPIOIE);
>> - gpioie &= ~(1 << offset);
>> - writeb(gpioie, chip->base + GPIOIE);
>> - spin_unlock_irqrestore(&chip->irq_lock, flags);
>> -}
>> -
>> -static void pl061_irq_enable(struct irq_data *d)
>> -{
>> - struct pl061_gpio *chip = irq_data_get_irq_chip_data(d);
>> - int offset = d->irq - chip->irq_base;
>> - unsigned long flags;
>> - u8 gpioie;
>> -
>> - spin_lock_irqsave(&chip->irq_lock, flags);
>> - gpioie = readb(chip->base + GPIOIE);
>> - gpioie |= 1 << offset;
>> - writeb(gpioie, chip->base + GPIOIE);
>> - spin_unlock_irqrestore(&chip->irq_lock, flags);
>> -}
>> -
>> static int pl061_irq_type(struct irq_data *d, unsigned trigger)
>> {
>> - struct pl061_gpio *chip = irq_data_get_irq_chip_data(d);
>> + struct irq_chip_generic *gc = irq_data_get_irq_chip_data(d);
>> + struct pl061_gpio *chip = gc->private;
>> int offset = d->irq - chip->irq_base;
>> unsigned long flags;
>> u8 gpiois, gpioibe, gpioiev;
>> @@ -166,7 +136,7 @@ static int pl061_irq_type(struct irq_data *d, unsigned trigger)
>> if (offset < 0 || offset >= PL061_GPIO_NR)
>> return -EINVAL;
>>
>> - spin_lock_irqsave(&chip->irq_lock, flags);
>> + raw_spin_lock_irqsave(&gc->lock, flags);
>>
>> gpioiev = readb(chip->base + GPIOIEV);
>>
>> @@ -195,18 +165,11 @@ static int pl061_irq_type(struct irq_data *d, unsigned trigger)
>>
>> writeb(gpioiev, chip->base + GPIOIEV);
>>
>> - spin_unlock_irqrestore(&chip->irq_lock, flags);
>> + raw_spin_unlock_irqrestore(&gc->lock, flags);
>>
>> return 0;
>> }
>>
>> -static struct irq_chip pl061_irqchip = {
>> - .name = "GPIO",
>> - .irq_enable = pl061_irq_enable,
>> - .irq_disable = pl061_irq_disable,
>> - .irq_set_type = pl061_irq_type,
>> -};
>> -
>> static void pl061_irq_handler(unsigned irq, struct irq_desc *desc)
>> {
>> struct list_head *chip_list = irq_get_handler_data(irq);
>> @@ -232,6 +195,25 @@ static void pl061_irq_handler(unsigned irq, struct irq_desc *desc)
>> chained_irq_exit(irqchip, desc);
>> }
>>
>> +static void __init pl061_init_gc(struct pl061_gpio *chip, int irq_base)
>> +{
>> + struct irq_chip_type *ct;
>> +
>> + chip->irq_gc = irq_alloc_generic_chip("gpio-pl061", 1, irq_base,
>> + chip->base, handle_simple_irq);
>> + chip->irq_gc->private = chip;
>> +
>> + ct = chip->irq_gc->chip_types;
>> + ct->chip.irq_mask = irq_gc_mask_clr_bit;
>> + ct->chip.irq_unmask = irq_gc_mask_set_bit;
>> + ct->chip.irq_set_type = pl061_irq_type;
>> + ct->chip.irq_set_wake = irq_gc_set_wake;
>> + ct->regs.mask = GPIOIE;
>> +
>> + irq_setup_generic_chip(chip->irq_gc, IRQ_MSK(PL061_GPIO_NR),
>> + IRQ_GC_INIT_NESTED_LOCK, IRQ_NOREQUEST, 0);
>> +}
>> +
>> static int pl061_probe(struct amba_device *dev, const struct amba_id *id)
>> {
>> struct pl061_platform_data *pdata;
>> @@ -269,7 +251,6 @@ static int pl061_probe(struct amba_device *dev, const struct amba_id *id)
>> }
>>
>> spin_lock_init(&chip->lock);
>> - spin_lock_init(&chip->irq_lock);
>> INIT_LIST_HEAD(&chip->list);
>>
>> chip->gc.direction_input = pl061_direction_input;
>> @@ -293,6 +274,8 @@ static int pl061_probe(struct amba_device *dev, const struct amba_id *id)
>> if (chip->irq_base <= 0)
>> return 0;
>>
>> + pl061_init_gc(chip, chip->irq_base);
>> +
>> writeb(0, chip->base + GPIOIE); /* disable irqs */
>> irq = dev->irq[0];
>> if (irq < 0) {
>> @@ -321,11 +304,6 @@ static int pl061_probe(struct amba_device *dev, const struct amba_id *id)
>> else
>> pl061_direction_input(&chip->gc, i);
>> }
>> -
>> - irq_set_chip_and_handler(i + chip->irq_base, &pl061_irqchip,
>> - handle_simple_irq);
>> - set_irq_flags(i+chip->irq_base, IRQF_VALID);
>> - irq_set_chip_data(i + chip->irq_base, chip);
>> }
>>
>> return 0;
>> --
>> 1.7.5.4
>>
next prev parent reply other threads:[~2012-01-02 16:54 UTC|newest]
Thread overview: 43+ messages / expand[flat|nested] mbox.gz Atom feed top
2011-12-14 15:28 [PATCH 0/9] irq domain for gen irq chip and pl061 DT irq support Rob Herring
2011-12-14 15:28 ` [PATCH 1/9] dt: add empty of_get_node/of_put_node functions Rob Herring
2011-12-14 16:02 ` Grant Likely
2011-12-14 15:28 ` [PATCH 2/9] irq: check domain hwirq range for DT translate Rob Herring
2011-12-14 16:08 ` Grant Likely
2011-12-15 5:23 ` Shawn Guo
2011-12-19 12:41 ` Cousson, Benoit
2011-12-19 14:23 ` Rob Herring
2011-12-19 15:21 ` Cousson, Benoit
2011-12-14 15:28 ` [PATCH 3/9] irq: convert generic-chip to use irq_domain Rob Herring
2011-12-14 21:14 ` Grant Likely
2011-12-14 21:23 ` Rob Herring
2011-12-14 21:26 ` Grant Likely
2011-12-14 23:29 ` Rob Herring
2011-12-15 5:25 ` Shawn Guo
2011-12-15 5:55 ` Shawn Guo
2011-12-15 13:39 ` Rob Herring
2011-12-15 13:56 ` Rob Herring
2011-12-15 14:15 ` Shawn Guo
2011-12-15 14:46 ` Shawn Guo
2011-12-15 15:55 ` Grant Likely
2011-12-15 16:17 ` Rob Herring
2011-12-15 16:39 ` Grant Likely
2011-12-15 14:08 ` Shawn Guo
2011-12-15 14:01 ` Rob Herring
2011-12-14 15:28 ` [PATCH 4/9] gpio: pl061: use chained_irq_* functions in irq handler Rob Herring
2011-12-14 21:15 ` Grant Likely
2011-12-14 15:28 ` [PATCH 5/9] gpio: pl061: convert to use 0 for no irq Rob Herring
2011-12-14 21:16 ` Grant Likely
2011-12-14 15:28 ` [PATCH 6/9] ARM: realview: convert pl061 no irq to 0 instead of -1 Rob Herring
2011-12-14 21:16 ` Grant Likely
2011-12-14 15:28 ` [PATCH 7/9] gpio: pl061: convert to use generic irq chip Rob Herring
2011-12-14 21:17 ` Grant Likely
2011-12-19 20:52 ` [PATCH v2] " Rob Herring
2011-12-24 23:26 ` Linus Walleij
2012-01-02 8:54 ` Grant Likely
2012-01-02 16:54 ` Rob Herring [this message]
2011-12-14 15:28 ` [PATCH 8/9] gpio: pl061: enable interrupts with DT style binding Rob Herring
2011-12-14 21:39 ` Grant Likely
2011-12-19 20:54 ` [PATCH v2] " Rob Herring
2011-12-14 15:28 ` [PATCH 9/9] ARM: highbank: add interrupt properties to gpio nodes Rob Herring
2011-12-14 21:39 ` Grant Likely
2011-12-14 15:41 ` [PATCH 0/9] irq domain for gen irq chip and pl061 DT irq support Rob Herring
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4F01E14C.9010407@gmail.com \
--to=robherring2@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).