From mboxrd@z Thu Jan  1 00:00:00 1970
From: nicolas.ferre@atmel.com (Nicolas Ferre)
Date: Mon, 09 Jan 2012 14:32:46 +0100
Subject: [PATCH] atmel_lcdfb: support 16bit BGR:565 mode,
 remove unsupported 15bit modes
In-Reply-To: <87ty45dt89.fsf@macbook.be.48ers.dk>
References: <1318517570-28459-1-git-send-email-jacmet@sunsite.dk>
 <4F0AC2B1.8010601@atmel.com> <87ty45dt89.fsf@macbook.be.48ers.dk>
Message-ID: <4F0AEC7E.5050403@atmel.com>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

On 01/09/2012 12:13 PM, Peter Korsgaard :
>>>>>> "Nicolas" == Nicolas Ferre <nicolas.ferre@atmel.com> writes:
> 
>  Nicolas> On 10/13/2011 04:52 PM, Peter Korsgaard :
>  >> Allow framebuffer to be configured in 16bit mode when panel is wired in
>  >> (the default) BGR configuration, and don't claim to support 15bit input
>  >> modes, which the LCD controller cannot handle.
>  >> 
>  >> Signed-off-by: Peter Korsgaard <jacmet@sunsite.dk>
> 
>  Nicolas> Hi Peter,
> 
>  Nicolas> Sorry for not having more responsive concerning the two
>  Nicolas> patches that you posted about atmel_lcdfb driver.
> 
> No problem.
> 
>  Nicolas> I have a question though about this one...
> 
>  >> -		} else if (sinfo->lcd_wiring_mode == ATMEL_LCDC_WIRING_RGB555) {
>  >> -			var->red.offset = 10;
>  >> -			var->blue.offset = 0;
>  >> -			var->green.length = 5;
> 
>  Nicolas> Maybe I have missed something but I do not know why you are removing
>  Nicolas> this part of the configuration? A board at least is using this wiring
>  Nicolas> mode...
> 
> Because it is arguable wrong as far as I understand the HW.
> There's two parts here:
> 
> - 1: Format of framebuffer memory
> - 2: Wiring of LCD (RGB/BGR order and number of bits)
> 
>>>From the datasheet, the following framebuffer formats are supported:
> 
> 1, 2, 4, 8 bits per pixel (palletized), 16, 24 bits per pixel
> (non-palletized) for TFT.
> 
> So it doesn't really support RGB555 mode. The controller reads up to
> 32bit of framebuffer data and outputs 24bit on the LCD pins. You CAN
> wire up a RGB555 panel by just skipping the LSB green of a RGB565
> wiring, but that is independent of the framebufffer format. The
> controller/driver doesn't do any RGB/BGR swapping, so the RBG/BGR wiring
> settings are just used as a software hint (in FBIOGET_VSCREENINFO) about
> the meaning of the individual bits of a pixel in the framebuffer.
> 
> Similar you can connect a 12bit 4:4:4 panel by just connecting it to the
> MSB LCD pins.

Yes. Thanks to Russell and you for the explanation.

I acknowledge your two patches right now.

> So in conclusion, I think we should just have:
> 
> - ATMEL_LCDC_WIRING_RGB
> - ATMEL_LCDC_WIRING_BGR
> - ATMEL_LCDC_WIRING_RGB565
> - ATMEL_LCDC_WIRING_BGR565
> 
> These simply define framebuffer bit order (RGB/BGR) and preferred
> default bit depth (16/24).

Maybe we can think about a patch that removes the RGB555 variable from
the header (include/video/atmel_lcdc.h) and the board file that is using
it (board-neocore926.c).

Best regards,
-- 
Nicolas Ferre