* [PATCH 0/3] add gpmi-nand dt support for mx6q-arm2 and imx28evk
@ 2012-04-20 9:24 Huang Shijie
2012-04-20 9:24 ` [PATCH 1/3] ARM: mx6q-arm2: add gpmi-nand dt support Huang Shijie
` (3 more replies)
0 siblings, 4 replies; 10+ messages in thread
From: Huang Shijie @ 2012-04-20 9:24 UTC (permalink / raw)
To: linux-arm-kernel
The mx6q-arm2 and imx28evk have already support the device tree now.
So i decide to add the gpmi-nand dt support to them.
The mx23 does not support the device tree now. I will add the gpmi dt support
when it is ready.
Test this patch set on both MX6Q-arm2 and mx28evk.
Huang Shijie (3):
ARM: mx6q-arm2: add gpmi-nand dt support
ARM: mx28evk: add gpmi-nand dt support
mtd: gpmi: add device tree support for mx6q-arm2 and mx28evk
.../devicetree/bindings/mtd/gpmi-nand.txt | 30 +++
arch/arm/boot/dts/imx28.dtsi | 9 +-
arch/arm/boot/dts/imx6q.dtsi | 12 +
arch/arm/mach-imx/clock-imx6q.c | 5 +-
arch/arm/mach-mxs/clock-mx28.c | 2 +-
drivers/mtd/nand/Kconfig | 2 +-
drivers/mtd/nand/gpmi-nand/bch-regs.h | 42 +++-
drivers/mtd/nand/gpmi-nand/gpmi-lib.c | 18 +-
drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 240 +++++++++-----------
drivers/mtd/nand/gpmi-nand/gpmi-nand.h | 6 +-
10 files changed, 202 insertions(+), 164 deletions(-)
create mode 100644 Documentation/devicetree/bindings/mtd/gpmi-nand.txt
^ permalink raw reply [flat|nested] 10+ messages in thread* [PATCH 1/3] ARM: mx6q-arm2: add gpmi-nand dt support 2012-04-20 9:24 [PATCH 0/3] add gpmi-nand dt support for mx6q-arm2 and imx28evk Huang Shijie @ 2012-04-20 9:24 ` Huang Shijie 2012-04-23 5:35 ` Shawn Guo 2012-04-20 9:24 ` [PATCH 2/3] ARM: mx28evk: " Huang Shijie ` (2 subsequent siblings) 3 siblings, 1 reply; 10+ messages in thread From: Huang Shijie @ 2012-04-20 9:24 UTC (permalink / raw) To: linux-arm-kernel add gpmi-nand dt support, and add the proper clock for gpmi-nand. Signed-off-by: Huang Shijie <b32955@freescale.com> --- arch/arm/boot/dts/imx6q.dtsi | 12 ++++++++++++ arch/arm/mach-imx/clock-imx6q.c | 5 +++-- 2 files changed, 15 insertions(+), 2 deletions(-) diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi index 4905f51..f23a0c4 100644 --- a/arch/arm/boot/dts/imx6q.dtsi +++ b/arch/arm/boot/dts/imx6q.dtsi @@ -87,6 +87,18 @@ interrupt-parent = <&intc>; ranges; + gpmi-nand at 00112000 { + compatible = "fsl,imx6q-gpmi-nand"; + reg = <0x00112000 0x2000>; + interrupts = <0 13 0x04>; + dma_channel = <0>; + }; + bch at 00114000 { + compatible = "fsl,imx6q-bch"; + reg = <0x00114000 0x2000>; + interrupts = <0 15 0x04>; + }; + timer at 00a00600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0x00a00600 0x20>; diff --git a/arch/arm/mach-imx/clock-imx6q.c b/arch/arm/mach-imx/clock-imx6q.c index 111c328..e3dc1b3 100644 --- a/arch/arm/mach-imx/clock-imx6q.c +++ b/arch/arm/mach-imx/clock-imx6q.c @@ -1859,7 +1859,8 @@ DEF_CLK(pwm1_clk, CCGR4, CG8, &ipg_perclk, NULL); DEF_CLK(pwm2_clk, CCGR4, CG9, &ipg_perclk, NULL); DEF_CLK(pwm3_clk, CCGR4, CG10, &ipg_perclk, NULL); DEF_CLK(pwm4_clk, CCGR4, CG11, &ipg_perclk, NULL); -DEF_CLK(gpmi_bch_apb_clk, CCGR4, CG12, &usdhc3_clk, NULL); +DEF_CLK(per1_bch_clk, CCGR4, CG6, &usdhc3_clk, NULL); +DEF_CLK(gpmi_bch_apb_clk, CCGR4, CG12, &usdhc3_clk, &per1_bch_clk); DEF_CLK(gpmi_bch_clk, CCGR4, CG13, &usdhc4_clk, &gpmi_bch_apb_clk); DEF_CLK(gpmi_apb_clk, CCGR4, CG15, &usdhc3_clk, &gpmi_bch_clk); DEF_CLK(gpmi_io_clk, CCGR4, CG14, &enfc_clk, &gpmi_apb_clk); @@ -1988,7 +1989,7 @@ static struct clk_lookup lookups[] = { _REGISTER_CLOCK(NULL, "pwm2_clk", pwm2_clk), _REGISTER_CLOCK(NULL, "pwm3_clk", pwm3_clk), _REGISTER_CLOCK(NULL, "pwm4_clk", pwm4_clk), - _REGISTER_CLOCK(NULL, "gpmi_io_clk", gpmi_io_clk), + _REGISTER_CLOCK("112000.gpmi-nand", NULL, gpmi_io_clk), _REGISTER_CLOCK(NULL, "usboh3_clk", usboh3_clk), _REGISTER_CLOCK(NULL, "sata_clk", sata_clk), _REGISTER_CLOCK(NULL, "cko1_clk", cko1_clk), -- 1.7.0.4 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH 1/3] ARM: mx6q-arm2: add gpmi-nand dt support 2012-04-20 9:24 ` [PATCH 1/3] ARM: mx6q-arm2: add gpmi-nand dt support Huang Shijie @ 2012-04-23 5:35 ` Shawn Guo 0 siblings, 0 replies; 10+ messages in thread From: Shawn Guo @ 2012-04-23 5:35 UTC (permalink / raw) To: linux-arm-kernel On Fri, Apr 20, 2012 at 05:24:17PM +0800, Huang Shijie wrote: > add gpmi-nand dt support, and add the proper clock for gpmi-nand. > > Signed-off-by: Huang Shijie <b32955@freescale.com> > --- > arch/arm/boot/dts/imx6q.dtsi | 12 ++++++++++++ > arch/arm/mach-imx/clock-imx6q.c | 5 +++-- > 2 files changed, 15 insertions(+), 2 deletions(-) > The patch subject suggests it touches some imx6q-arm2 specific files, while the diffstat says no. I think the reason for that is you missed one fact. Generally, the peripherals defined in imx6q.dtsi should be disabled by default (status = "disabled"), and need to to be enabled (status = "okay") by <board>.dts file. > diff --git a/arch/arm/boot/dts/imx6q.dtsi b/arch/arm/boot/dts/imx6q.dtsi > index 4905f51..f23a0c4 100644 > --- a/arch/arm/boot/dts/imx6q.dtsi > +++ b/arch/arm/boot/dts/imx6q.dtsi > @@ -87,6 +87,18 @@ > interrupt-parent = <&intc>; > ranges; > > + gpmi-nand at 00112000 { > + compatible = "fsl,imx6q-gpmi-nand"; > + reg = <0x00112000 0x2000>; > + interrupts = <0 13 0x04>; > + dma_channel = <0>; > + }; Add a new line between two nodes. Regards, Shawn > + bch at 00114000 { > + compatible = "fsl,imx6q-bch"; > + reg = <0x00114000 0x2000>; > + interrupts = <0 15 0x04>; > + }; > + > timer at 00a00600 { > compatible = "arm,cortex-a9-twd-timer"; > reg = <0x00a00600 0x20>; > diff --git a/arch/arm/mach-imx/clock-imx6q.c b/arch/arm/mach-imx/clock-imx6q.c > index 111c328..e3dc1b3 100644 > --- a/arch/arm/mach-imx/clock-imx6q.c > +++ b/arch/arm/mach-imx/clock-imx6q.c > @@ -1859,7 +1859,8 @@ DEF_CLK(pwm1_clk, CCGR4, CG8, &ipg_perclk, NULL); > DEF_CLK(pwm2_clk, CCGR4, CG9, &ipg_perclk, NULL); > DEF_CLK(pwm3_clk, CCGR4, CG10, &ipg_perclk, NULL); > DEF_CLK(pwm4_clk, CCGR4, CG11, &ipg_perclk, NULL); > -DEF_CLK(gpmi_bch_apb_clk, CCGR4, CG12, &usdhc3_clk, NULL); > +DEF_CLK(per1_bch_clk, CCGR4, CG6, &usdhc3_clk, NULL); > +DEF_CLK(gpmi_bch_apb_clk, CCGR4, CG12, &usdhc3_clk, &per1_bch_clk); > DEF_CLK(gpmi_bch_clk, CCGR4, CG13, &usdhc4_clk, &gpmi_bch_apb_clk); > DEF_CLK(gpmi_apb_clk, CCGR4, CG15, &usdhc3_clk, &gpmi_bch_clk); > DEF_CLK(gpmi_io_clk, CCGR4, CG14, &enfc_clk, &gpmi_apb_clk); > @@ -1988,7 +1989,7 @@ static struct clk_lookup lookups[] = { > _REGISTER_CLOCK(NULL, "pwm2_clk", pwm2_clk), > _REGISTER_CLOCK(NULL, "pwm3_clk", pwm3_clk), > _REGISTER_CLOCK(NULL, "pwm4_clk", pwm4_clk), > - _REGISTER_CLOCK(NULL, "gpmi_io_clk", gpmi_io_clk), > + _REGISTER_CLOCK("112000.gpmi-nand", NULL, gpmi_io_clk), > _REGISTER_CLOCK(NULL, "usboh3_clk", usboh3_clk), > _REGISTER_CLOCK(NULL, "sata_clk", sata_clk), > _REGISTER_CLOCK(NULL, "cko1_clk", cko1_clk), > -- > 1.7.0.4 > > ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 2/3] ARM: mx28evk: add gpmi-nand dt support 2012-04-20 9:24 [PATCH 0/3] add gpmi-nand dt support for mx6q-arm2 and imx28evk Huang Shijie 2012-04-20 9:24 ` [PATCH 1/3] ARM: mx6q-arm2: add gpmi-nand dt support Huang Shijie @ 2012-04-20 9:24 ` Huang Shijie 2012-04-23 5:38 ` Shawn Guo 2012-04-20 9:24 ` [PATCH 3/3] mtd: gpmi: add device tree support for mx6q-arm2 and mx28evk Huang Shijie 2012-04-23 5:26 ` [PATCH 0/3] add gpmi-nand dt support for mx6q-arm2 and imx28evk Shawn Guo 3 siblings, 1 reply; 10+ messages in thread From: Huang Shijie @ 2012-04-20 9:24 UTC (permalink / raw) To: linux-arm-kernel add gpmi-nand device tree support, and add proper clock for it. Signed-off-by: Huang Shijie <b32955@freescale.com> --- arch/arm/boot/dts/imx28.dtsi | 9 +++++---- arch/arm/mach-mxs/clock-mx28.c | 2 +- 2 files changed, 6 insertions(+), 5 deletions(-) diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi index dd209a3..2804a43 100644 --- a/arch/arm/boot/dts/imx28.dtsi +++ b/arch/arm/boot/dts/imx28.dtsi @@ -63,15 +63,16 @@ }; bch at 8000a000 { + compatible = "fsl,imx28-bch"; reg = <0x8000a000 2000>; interrupts = <41>; - status = "disabled"; }; - gpmi at 8000c000 { + gpmi-nand at 8000c000 { + compatible = "fsl,imx28-gpmi-nand"; reg = <0x8000c000 2000>; - interrupts = <42 88>; - status = "disabled"; + interrupts = <88>; + dma_channel = <4>; }; ssp at 80010000 { diff --git a/arch/arm/mach-mxs/clock-mx28.c b/arch/arm/mach-mxs/clock-mx28.c index 8401854..6fe6737 100644 --- a/arch/arm/mach-mxs/clock-mx28.c +++ b/arch/arm/mach-mxs/clock-mx28.c @@ -617,7 +617,6 @@ static struct clk_lookup lookups[] = { _REGISTER_CLOCK("duart", NULL, uart_clk) _REGISTER_CLOCK("imx28-fec.0", NULL, fec_clk) _REGISTER_CLOCK("imx28-fec.1", NULL, fec_clk) - _REGISTER_CLOCK("imx28-gpmi-nand", NULL, gpmi_clk) _REGISTER_CLOCK("mxs-auart.0", NULL, uart_clk) _REGISTER_CLOCK("mxs-auart.1", NULL, uart_clk) _REGISTER_CLOCK("mxs-auart.2", NULL, uart_clk) @@ -649,6 +648,7 @@ static struct clk_lookup lookups[] = { _REGISTER_CLOCK("mxs-saif.0", NULL, saif0_clk) _REGISTER_CLOCK("mxs-saif.1", NULL, saif1_clk) /* for DT */ + _REGISTER_CLOCK("8000c000.gpmi-nand", NULL, gpmi_clk) _REGISTER_CLOCK("80074000.serial", NULL, uart_clk) _REGISTER_CLOCK("800f0000.ethernet", NULL, fec_clk) _REGISTER_CLOCK("800f4000.ethernet", NULL, fec_clk) -- 1.7.0.4 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH 2/3] ARM: mx28evk: add gpmi-nand dt support 2012-04-20 9:24 ` [PATCH 2/3] ARM: mx28evk: " Huang Shijie @ 2012-04-23 5:38 ` Shawn Guo 0 siblings, 0 replies; 10+ messages in thread From: Shawn Guo @ 2012-04-23 5:38 UTC (permalink / raw) To: linux-arm-kernel On Fri, Apr 20, 2012 at 05:24:18PM +0800, Huang Shijie wrote: > add gpmi-nand device tree support, and add proper clock for it. > > Signed-off-by: Huang Shijie <b32955@freescale.com> > --- > arch/arm/boot/dts/imx28.dtsi | 9 +++++---- > arch/arm/mach-mxs/clock-mx28.c | 2 +- > 2 files changed, 6 insertions(+), 5 deletions(-) > > diff --git a/arch/arm/boot/dts/imx28.dtsi b/arch/arm/boot/dts/imx28.dtsi > index dd209a3..2804a43 100644 > --- a/arch/arm/boot/dts/imx28.dtsi > +++ b/arch/arm/boot/dts/imx28.dtsi > @@ -63,15 +63,16 @@ > }; > > bch at 8000a000 { > + compatible = "fsl,imx28-bch"; > reg = <0x8000a000 2000>; > interrupts = <41>; > - status = "disabled"; > }; > > - gpmi at 8000c000 { > + gpmi-nand at 8000c000 { > + compatible = "fsl,imx28-gpmi-nand"; > reg = <0x8000c000 2000>; > - interrupts = <42 88>; > - status = "disabled"; Keep the line and enable it in <board>.dts file. Regards, Shawn > + interrupts = <88>; > + dma_channel = <4>; > }; > > ssp at 80010000 { > diff --git a/arch/arm/mach-mxs/clock-mx28.c b/arch/arm/mach-mxs/clock-mx28.c > index 8401854..6fe6737 100644 > --- a/arch/arm/mach-mxs/clock-mx28.c > +++ b/arch/arm/mach-mxs/clock-mx28.c > @@ -617,7 +617,6 @@ static struct clk_lookup lookups[] = { > _REGISTER_CLOCK("duart", NULL, uart_clk) > _REGISTER_CLOCK("imx28-fec.0", NULL, fec_clk) > _REGISTER_CLOCK("imx28-fec.1", NULL, fec_clk) > - _REGISTER_CLOCK("imx28-gpmi-nand", NULL, gpmi_clk) > _REGISTER_CLOCK("mxs-auart.0", NULL, uart_clk) > _REGISTER_CLOCK("mxs-auart.1", NULL, uart_clk) > _REGISTER_CLOCK("mxs-auart.2", NULL, uart_clk) > @@ -649,6 +648,7 @@ static struct clk_lookup lookups[] = { > _REGISTER_CLOCK("mxs-saif.0", NULL, saif0_clk) > _REGISTER_CLOCK("mxs-saif.1", NULL, saif1_clk) > /* for DT */ > + _REGISTER_CLOCK("8000c000.gpmi-nand", NULL, gpmi_clk) > _REGISTER_CLOCK("80074000.serial", NULL, uart_clk) > _REGISTER_CLOCK("800f0000.ethernet", NULL, fec_clk) > _REGISTER_CLOCK("800f4000.ethernet", NULL, fec_clk) > -- > 1.7.0.4 > > ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 3/3] mtd: gpmi: add device tree support for mx6q-arm2 and mx28evk 2012-04-20 9:24 [PATCH 0/3] add gpmi-nand dt support for mx6q-arm2 and imx28evk Huang Shijie 2012-04-20 9:24 ` [PATCH 1/3] ARM: mx6q-arm2: add gpmi-nand dt support Huang Shijie 2012-04-20 9:24 ` [PATCH 2/3] ARM: mx28evk: " Huang Shijie @ 2012-04-20 9:24 ` Huang Shijie 2012-04-23 6:43 ` Shawn Guo 2012-04-23 5:26 ` [PATCH 0/3] add gpmi-nand dt support for mx6q-arm2 and imx28evk Shawn Guo 3 siblings, 1 reply; 10+ messages in thread From: Huang Shijie @ 2012-04-20 9:24 UTC (permalink / raw) To: linux-arm-kernel add DT support to mx6q-arm2 and mx28evk. Signed-off-by: Huang Shijie <b32955@freescale.com> --- .../devicetree/bindings/mtd/gpmi-nand.txt | 30 +++ drivers/mtd/nand/Kconfig | 2 +- drivers/mtd/nand/gpmi-nand/bch-regs.h | 42 +++- drivers/mtd/nand/gpmi-nand/gpmi-lib.c | 18 +- drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 240 +++++++++----------- drivers/mtd/nand/gpmi-nand/gpmi-nand.h | 6 +- 6 files changed, 181 insertions(+), 157 deletions(-) create mode 100644 Documentation/devicetree/bindings/mtd/gpmi-nand.txt diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt new file mode 100644 index 0000000..e1181ee --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt @@ -0,0 +1,30 @@ +* Freescale General-Purpose Media Interface (GPMI) + +The GPMI nand controller provides an interface to control the +NAND flash chips. We support only one NAND chips now. + +The GPMI nand controller required properties: + - compatible : should be "fsl,<chip>-gpmi-nand" + - reg : should contain registers location and length. + - interrupts : should contain the DMA interrupt number for GPMI. + We do not use the GPMI interrupt. + - dma_channel: Should contain the dma channel it uses. + +The BCH required properties: + - compatible : should be "fsl,<chip>-bch" + - reg : should contain registers location and length. + - interrupts : should contain the BCH interrupt. + +Examples: + +gpmi-nand at 8000c000 { + compatible = "fsl,imx28-gpmi-nand"; + reg = <0x8000c000 2000>; + interrupts = <88>; + dma_channel = <4>; +}; +bch at 8000a000 { + compatible = "fsl,imx28-bch"; + reg = <0x8000a000 2000>; + interrupts = <41>; +}; diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig index 7d17cec..bf0a28d 100644 --- a/drivers/mtd/nand/Kconfig +++ b/drivers/mtd/nand/Kconfig @@ -440,7 +440,7 @@ config MTD_NAND_NANDSIM config MTD_NAND_GPMI_NAND bool "GPMI NAND Flash Controller driver" - depends on MTD_NAND && (SOC_IMX23 || SOC_IMX28) + depends on MTD_NAND && (SOC_IMX23 || SOC_IMX28 || SOC_IMX6Q) help Enables NAND Flash support for IMX23 or IMX28. The GPMI controller is very powerful, with the help of BCH diff --git a/drivers/mtd/nand/gpmi-nand/bch-regs.h b/drivers/mtd/nand/gpmi-nand/bch-regs.h index 4effb8c..a092451 100644 --- a/drivers/mtd/nand/gpmi-nand/bch-regs.h +++ b/drivers/mtd/nand/gpmi-nand/bch-regs.h @@ -51,15 +51,26 @@ #define BP_BCH_FLASH0LAYOUT0_ECC0 12 #define BM_BCH_FLASH0LAYOUT0_ECC0 (0xf << BP_BCH_FLASH0LAYOUT0_ECC0) -#define BF_BCH_FLASH0LAYOUT0_ECC0(v) \ - (((v) << BP_BCH_FLASH0LAYOUT0_ECC0) & BM_BCH_FLASH0LAYOUT0_ECC0) +#define MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0 11 +#define MX6Q_BM_BCH_FLASH0LAYOUT0_ECC0 (0x1f << MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0) +#define BF_BCH_FLASH0LAYOUT0_ECC0(v, x) \ + (GPMI_IS_MX6Q(x) \ + ? (((v) << MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0) \ + & MX6Q_BM_BCH_FLASH0LAYOUT0_ECC0) \ + : (((v) << BP_BCH_FLASH0LAYOUT0_ECC0) \ + & BM_BCH_FLASH0LAYOUT0_ECC0) \ + ) #define BP_BCH_FLASH0LAYOUT0_DATA0_SIZE 0 #define BM_BCH_FLASH0LAYOUT0_DATA0_SIZE \ (0xfff << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE) -#define BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(v) \ - (((v) << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE)\ - & BM_BCH_FLASH0LAYOUT0_DATA0_SIZE) +#define MX6Q_BM_BCH_FLASH0LAYOUT0_DATA0_SIZE \ + (0x3ff << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE) +#define BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(v, x) \ + (GPMI_IS_MX6Q(x) \ + ? (((v) >> 2) & MX6Q_BM_BCH_FLASH0LAYOUT0_DATA0_SIZE) \ + : ((v) & BM_BCH_FLASH0LAYOUT0_DATA0_SIZE) \ + ) #define HW_BCH_FLASH0LAYOUT1 0x00000090 @@ -72,13 +83,24 @@ #define BP_BCH_FLASH0LAYOUT1_ECCN 12 #define BM_BCH_FLASH0LAYOUT1_ECCN (0xf << BP_BCH_FLASH0LAYOUT1_ECCN) -#define BF_BCH_FLASH0LAYOUT1_ECCN(v) \ - (((v) << BP_BCH_FLASH0LAYOUT1_ECCN) & BM_BCH_FLASH0LAYOUT1_ECCN) +#define MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN 11 +#define MX6Q_BM_BCH_FLASH0LAYOUT1_ECCN (0x1f << MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN) +#define BF_BCH_FLASH0LAYOUT1_ECCN(v, x) \ + (GPMI_IS_MX6Q(x) \ + ? (((v) << MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN) \ + & MX6Q_BM_BCH_FLASH0LAYOUT1_ECCN) \ + : (((v) << BP_BCH_FLASH0LAYOUT1_ECCN) \ + & BM_BCH_FLASH0LAYOUT1_ECCN) \ + ) #define BP_BCH_FLASH0LAYOUT1_DATAN_SIZE 0 #define BM_BCH_FLASH0LAYOUT1_DATAN_SIZE \ (0xfff << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE) -#define BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(v) \ - (((v) << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE) \ - & BM_BCH_FLASH0LAYOUT1_DATAN_SIZE) +#define MX6Q_BM_BCH_FLASH0LAYOUT1_DATAN_SIZE \ + (0x3ff << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE) +#define BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(v, x) \ + (GPMI_IS_MX6Q(x) \ + ? (((v) >> 2) & MX6Q_BM_BCH_FLASH0LAYOUT1_DATAN_SIZE) \ + : ((v) & BM_BCH_FLASH0LAYOUT1_DATAN_SIZE) \ + ) #endif diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c index fa5200b..a1f4332 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c +++ b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c @@ -224,13 +224,13 @@ int bch_set_geometry(struct gpmi_nand_data *this) /* Configure layout 0. */ writel(BF_BCH_FLASH0LAYOUT0_NBLOCKS(block_count) | BF_BCH_FLASH0LAYOUT0_META_SIZE(metadata_size) - | BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength) - | BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size), + | BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength, this) + | BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size, this), r->bch_regs + HW_BCH_FLASH0LAYOUT0); writel(BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(page_size) - | BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength) - | BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size), + | BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength, this) + | BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size, this), r->bch_regs + HW_BCH_FLASH0LAYOUT1); /* Set *all* chip selects to use layout 0. */ @@ -256,11 +256,12 @@ static unsigned int ns_to_cycles(unsigned int time, return max(k, min); } +#define DEF_MIN_PROP_DELAY 5 +#define DEF_MAX_PROP_DELAY 9 /* Apply timing to current hardware conditions. */ static int gpmi_nfc_compute_hardware_timing(struct gpmi_nand_data *this, struct gpmi_nfc_hardware_timing *hw) { - struct gpmi_nand_platform_data *pdata = this->pdata; struct timing_threshod *nfc = &timing_default_threshold; struct nand_chip *nand = &this->nand; struct nand_timing target = this->timing; @@ -277,8 +278,8 @@ static int gpmi_nfc_compute_hardware_timing(struct gpmi_nand_data *this, int ideal_sample_delay_in_ns; unsigned int sample_delay_factor; int tEYE; - unsigned int min_prop_delay_in_ns = pdata->min_prop_delay_in_ns; - unsigned int max_prop_delay_in_ns = pdata->max_prop_delay_in_ns; + unsigned int min_prop_delay_in_ns = DEF_MIN_PROP_DELAY; + unsigned int max_prop_delay_in_ns = DEF_MAX_PROP_DELAY; /* * If there are multiple chips, we need to relax the timings to allow @@ -804,7 +805,8 @@ int gpmi_is_ready(struct gpmi_nand_data *this, unsigned chip) if (GPMI_IS_MX23(this)) { mask = MX23_BM_GPMI_DEBUG_READY0 << chip; reg = readl(r->gpmi_regs + HW_GPMI_DEBUG); - } else if (GPMI_IS_MX28(this)) { + } else if (GPMI_IS_MX28(this) || GPMI_IS_MX6Q(this)) { + /* MX28 shares the same R/B register as MX6Q. */ mask = MX28_BF_GPMI_STAT_READY_BUSY(1 << chip); reg = readl(r->gpmi_regs + HW_GPMI_STAT); } else diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c index 75b1dde..5c6af5d 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c @@ -24,6 +24,9 @@ #include <linux/module.h> #include <linux/mtd/gpmi-nand.h> #include <linux/mtd/partitions.h> +#include <linux/of_address.h> +#include <linux/of_device.h> +#include <linux/of_irq.h> #include "gpmi-nand.h" /* add our owner bbt descriptor */ @@ -306,36 +309,6 @@ int start_dma_with_bch_irq(struct gpmi_nand_data *this, return 0; } -static int __devinit -acquire_register_block(struct gpmi_nand_data *this, const char *res_name) -{ - struct platform_device *pdev = this->pdev; - struct resources *res = &this->resources; - struct resource *r; - void *p; - - r = platform_get_resource_byname(pdev, IORESOURCE_MEM, res_name); - if (!r) { - pr_err("Can't get resource for %s\n", res_name); - return -ENXIO; - } - - p = ioremap(r->start, resource_size(r)); - if (!p) { - pr_err("Can't remap %s\n", res_name); - return -ENOMEM; - } - - if (!strcmp(res_name, GPMI_NAND_GPMI_REGS_ADDR_RES_NAME)) - res->gpmi_regs = p; - else if (!strcmp(res_name, GPMI_NAND_BCH_REGS_ADDR_RES_NAME)) - res->bch_regs = p; - else - pr_err("unknown resource name : %s\n", res_name); - - return 0; -} - static void release_register_block(struct gpmi_nand_data *this) { struct resources *res = &this->resources; @@ -347,32 +320,6 @@ static void release_register_block(struct gpmi_nand_data *this) res->bch_regs = NULL; } -static int __devinit -acquire_bch_irq(struct gpmi_nand_data *this, irq_handler_t irq_h) -{ - struct platform_device *pdev = this->pdev; - struct resources *res = &this->resources; - const char *res_name = GPMI_NAND_BCH_INTERRUPT_RES_NAME; - struct resource *r; - int err; - - r = platform_get_resource_byname(pdev, IORESOURCE_IRQ, res_name); - if (!r) { - pr_err("Can't get resource for %s\n", res_name); - return -ENXIO; - } - - err = request_irq(r->start, irq_h, 0, res_name, this); - if (err) { - pr_err("Can't own %s\n", res_name); - return err; - } - - res->bch_low_interrupt = r->start; - res->bch_high_interrupt = r->end; - return 0; -} - static void release_bch_irq(struct gpmi_nand_data *this) { struct resources *res = &this->resources; @@ -385,7 +332,7 @@ static void release_bch_irq(struct gpmi_nand_data *this) static bool gpmi_dma_filter(struct dma_chan *chan, void *param) { struct gpmi_nand_data *this = param; - struct resource *r = this->private; + int dma_channel = (int)this->private; if (!mxs_dma_is_apbh(chan)) return false; @@ -397,7 +344,7 @@ static bool gpmi_dma_filter(struct dma_chan *chan, void *param) * for mx28 : MX28_DMA_GPMI0 ~ MX28_DMA_GPMI7 * (These eight channels share the same IRQ!) */ - if (r->start <= chan->chan_id && chan->chan_id <= r->end) { + if (dma_channel == chan->chan_id) { chan->private = &this->dma_data; return true; } @@ -414,85 +361,91 @@ static void release_dma_channels(struct gpmi_nand_data *this) } } -static int __devinit acquire_dma_channels(struct gpmi_nand_data *this) +static const char *bch_node_name[] __devinitconst = { + [IS_MX23] = "fsl,imx23-bch", + [IS_MX28] = "fsl,imx28-bch", + [IS_MX6Q] = "fsl,imx6q-bch", +}; + +static int __devinit acquire_resources(struct gpmi_nand_data *this) { - struct platform_device *pdev = this->pdev; - struct gpmi_nand_platform_data *pdata = this->pdata; struct resources *res = &this->resources; - struct resource *r, *r_dma; - unsigned int i; + struct platform_device *pdev = this->pdev; + struct resource *r; + struct device_node *dn; + unsigned int irq; + int ret = -EINVAL; + + /* gpmi */ + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!r) { + pr_err("Can't get gpmi resource.\n"); + goto exit_regs; + } - r = platform_get_resource_byname(pdev, IORESOURCE_DMA, - GPMI_NAND_DMA_CHANNELS_RES_NAME); - r_dma = platform_get_resource_byname(pdev, IORESOURCE_IRQ, - GPMI_NAND_DMA_INTERRUPT_RES_NAME); - if (!r || !r_dma) { - pr_err("Can't get resource for DMA\n"); - return -ENXIO; + res->gpmi_regs = ioremap(r->start, resource_size(r)); + if (!res->gpmi_regs) { + pr_err("Can't remap for gpmi.\n"); + goto exit_regs; } - /* used in gpmi_dma_filter() */ - this->private = r; + /* bch */ + dn = of_find_compatible_node(NULL, NULL, + bch_node_name[pdev->id_entry->driver_data]); + if (dn) { + res->bch_regs = of_iomap(dn, 0); + if (!res->bch_regs) { + of_node_put(dn); + goto exit_regs; + } + } else { + pr_err("Can't find device node for BCH.\n"); + goto exit_regs; + } - for (i = r->start; i <= r->end; i++) { + irq = irq_of_parse_and_map(dn, 0); + ret = request_irq(irq, bch_irq, 0, NULL, this); + if (ret) { + of_node_put(dn); + pr_err("interrupt request failed\n"); + goto exit_regs; + } + res->bch_low_interrupt = res->bch_high_interrupt = irq; + of_node_put(dn); + + /* apbh-dma channel */ + r = platform_get_resource(pdev, IORESOURCE_IRQ, 0); + if (r) { struct dma_chan *dma_chan; dma_cap_mask_t mask; - - if (i - r->start >= pdata->max_chip_count) - break; + int dma_channel; dma_cap_zero(mask); dma_cap_set(DMA_SLAVE, mask); - /* get the DMA interrupt */ - if (r_dma->start == r_dma->end) { - /* only register the first. */ - if (i == r->start) - this->dma_data.chan_irq = r_dma->start; - else - this->dma_data.chan_irq = NO_IRQ; - } else - this->dma_data.chan_irq = r_dma->start + (i - r->start); - - dma_chan = dma_request_channel(mask, gpmi_dma_filter, this); - if (!dma_chan) - goto acquire_err; - - /* fill the first empty item */ - this->dma_chans[i - r->start] = dma_chan; - } - - res->dma_low_channel = r->start; - res->dma_high_channel = i; - return 0; - -acquire_err: - pr_err("Can't acquire DMA channel %u\n", i); - release_dma_channels(this); - return -EINVAL; -} - -static int __devinit acquire_resources(struct gpmi_nand_data *this) -{ - struct resources *res = &this->resources; - int ret; - - ret = acquire_register_block(this, GPMI_NAND_GPMI_REGS_ADDR_RES_NAME); - if (ret) - goto exit_regs; - - ret = acquire_register_block(this, GPMI_NAND_BCH_REGS_ADDR_RES_NAME); - if (ret) - goto exit_regs; + this->dma_data.chan_irq = r->start; - ret = acquire_bch_irq(this, bch_irq); - if (ret) - goto exit_regs; + /* We only support one chip now, so we need one DMA channel.*/ + dn = pdev->dev.of_node; + ret = of_property_read_u32(dn, "dma_channel", &dma_channel); + if (ret) { + pr_err("unable to get DMA channel from dt.\n"); + goto exit_dma_channels; + } + this->private = (void *)dma_channel; - ret = acquire_dma_channels(this); - if (ret) + dma_chan = dma_request_channel(mask, gpmi_dma_filter, this); + if (!dma_chan) { + pr_err("dma_request_channel failed.\n"); + goto exit_dma_channels; + } + this->dma_chans[0] = dma_chan; + } else { + pr_err("Can't find irq for dma\n"); goto exit_dma_channels; + } + /* gpmi clock */ res->clock = clk_get(&this->pdev->dev, NULL); if (IS_ERR(res->clock)) { pr_err("can not get the clock\n"); @@ -1461,7 +1414,6 @@ void gpmi_nfc_exit(struct gpmi_nand_data *this) static int __devinit gpmi_nfc_init(struct gpmi_nand_data *this) { - struct gpmi_nand_platform_data *pdata = this->pdata; struct mtd_info *mtd = &this->mtd; struct nand_chip *chip = &this->nand; int ret; @@ -1501,14 +1453,13 @@ static int __devinit gpmi_nfc_init(struct gpmi_nand_data *this) if (ret) goto err_out; - ret = nand_scan(mtd, pdata->max_chip_count); + ret = nand_scan(mtd, 1); if (ret) { pr_err("Chip scan failed\n"); goto err_out; } - ret = mtd_device_parse_register(mtd, NULL, NULL, - pdata->partitions, pdata->partition_count); + ret = mtd_device_parse_register(mtd, NULL, NULL, NULL, 0); if (ret) goto err_out; return 0; @@ -1518,12 +1469,38 @@ err_out: return ret; } +static const struct platform_device_id gpmi_ids[] = { + { .name = "imx23-gpmi-nand", .driver_data = IS_MX23, }, + { .name = "imx28-gpmi-nand", .driver_data = IS_MX28, }, + { .name = "imx6q-gpmi-nand", .driver_data = IS_MX6Q, }, + {}, +}; + +static const struct of_device_id gpmi_nand_id_table[] = { + { + .compatible = "fsl,imx23-gpmi-nand", + .data = (void *)&gpmi_ids[IS_MX23] + }, { + .compatible = "fsl,imx28-gpmi-nand", + .data = (void *)&gpmi_ids[IS_MX28] + }, { + .compatible = "fsl,imx6q-gpmi-nand", + .data = (void *)&gpmi_ids[IS_MX6Q] + }, {} +}; +MODULE_DEVICE_TABLE(of, gpmi_nand_id_table); + static int __devinit gpmi_nand_probe(struct platform_device *pdev) { struct gpmi_nand_platform_data *pdata = pdev->dev.platform_data; struct gpmi_nand_data *this; + const struct of_device_id *of_id; int ret; + of_id = of_match_device(gpmi_nand_id_table, &pdev->dev); + if (of_id) + pdev->id_entry = of_id->data; + this = kzalloc(sizeof(*this), GFP_KERNEL); if (!this) { pr_err("Failed to allocate per-device memory\n"); @@ -1535,7 +1512,7 @@ static int __devinit gpmi_nand_probe(struct platform_device *pdev) this->dev = &pdev->dev; this->pdata = pdata; - if (pdata->platform_init) { + if (pdata && pdata->platform_init) { ret = pdata->platform_init(); if (ret) goto platform_init_error; @@ -1575,19 +1552,10 @@ static int __exit gpmi_nand_remove(struct platform_device *pdev) return 0; } -static const struct platform_device_id gpmi_ids[] = { - { - .name = "imx23-gpmi-nand", - .driver_data = IS_MX23, - }, { - .name = "imx28-gpmi-nand", - .driver_data = IS_MX28, - }, {}, -}; - static struct platform_driver gpmi_nand_driver = { .driver = { .name = "gpmi-nand", + .of_match_table = gpmi_nand_id_table, }, .probe = gpmi_nand_probe, .remove = __exit_p(gpmi_nand_remove), diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.h b/drivers/mtd/nand/gpmi-nand/gpmi-nand.h index ec6180d..ce5daa1 100644 --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.h +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.h @@ -266,8 +266,10 @@ extern int gpmi_read_page(struct gpmi_nand_data *, #define STATUS_UNCORRECTABLE 0xfe /* Use the platform_id to distinguish different Archs. */ -#define IS_MX23 0x1 -#define IS_MX28 0x2 +#define IS_MX23 0x0 +#define IS_MX28 0x1 +#define IS_MX6Q 0x2 #define GPMI_IS_MX23(x) ((x)->pdev->id_entry->driver_data == IS_MX23) #define GPMI_IS_MX28(x) ((x)->pdev->id_entry->driver_data == IS_MX28) +#define GPMI_IS_MX6Q(x) ((x)->pdev->id_entry->driver_data == IS_MX6Q) #endif -- 1.7.0.4 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH 3/3] mtd: gpmi: add device tree support for mx6q-arm2 and mx28evk 2012-04-20 9:24 ` [PATCH 3/3] mtd: gpmi: add device tree support for mx6q-arm2 and mx28evk Huang Shijie @ 2012-04-23 6:43 ` Shawn Guo 2012-04-23 8:10 ` Huang Shijie 0 siblings, 1 reply; 10+ messages in thread From: Shawn Guo @ 2012-04-23 6:43 UTC (permalink / raw) To: linux-arm-kernel On Fri, Apr 20, 2012 at 05:24:19PM +0800, Huang Shijie wrote: > add DT support to mx6q-arm2 and mx28evk. > Again, this is not a support about board but soc. > Signed-off-by: Huang Shijie <b32955@freescale.com> > --- > .../devicetree/bindings/mtd/gpmi-nand.txt | 30 +++ > drivers/mtd/nand/Kconfig | 2 +- > drivers/mtd/nand/gpmi-nand/bch-regs.h | 42 +++- > drivers/mtd/nand/gpmi-nand/gpmi-lib.c | 18 +- > drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 240 +++++++++----------- > drivers/mtd/nand/gpmi-nand/gpmi-nand.h | 6 +- > 6 files changed, 181 insertions(+), 157 deletions(-) > create mode 100644 Documentation/devicetree/bindings/mtd/gpmi-nand.txt > > diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt > new file mode 100644 > index 0000000..e1181ee > --- /dev/null > +++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt > @@ -0,0 +1,30 @@ > +* Freescale General-Purpose Media Interface (GPMI) > + > +The GPMI nand controller provides an interface to control the > +NAND flash chips. We support only one NAND chips now. > + > +The GPMI nand controller required properties: > + - compatible : should be "fsl,<chip>-gpmi-nand" > + - reg : should contain registers location and length. > + - interrupts : should contain the DMA interrupt number for GPMI. > + We do not use the GPMI interrupt. > + - dma_channel: Should contain the dma channel it uses. > + > +The BCH required properties: > + - compatible : should be "fsl,<chip>-bch" > + - reg : should contain registers location and length. > + - interrupts : should contain the BCH interrupt. > + > +Examples: > + > +gpmi-nand at 8000c000 { > + compatible = "fsl,imx28-gpmi-nand"; > + reg = <0x8000c000 2000>; > + interrupts = <88>; > + dma_channel = <4>; Before generic dma helper is available, do not use such generic property name, and use something like "fsl,gpmi-dma-events". Yes, "-" rather than "_" should be used in property name. > +}; > +bch at 8000a000 { > + compatible = "fsl,imx28-bch"; > + reg = <0x8000a000 2000>; > + interrupts = <41>; > +}; > diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig > index 7d17cec..bf0a28d 100644 > --- a/drivers/mtd/nand/Kconfig > +++ b/drivers/mtd/nand/Kconfig > @@ -440,7 +440,7 @@ config MTD_NAND_NANDSIM > > config MTD_NAND_GPMI_NAND > bool "GPMI NAND Flash Controller driver" > - depends on MTD_NAND && (SOC_IMX23 || SOC_IMX28) > + depends on MTD_NAND && (SOC_IMX23 || SOC_IMX28 || SOC_IMX6Q) > help > Enables NAND Flash support for IMX23 or IMX28. > The GPMI controller is very powerful, with the help of BCH > diff --git a/drivers/mtd/nand/gpmi-nand/bch-regs.h b/drivers/mtd/nand/gpmi-nand/bch-regs.h > index 4effb8c..a092451 100644 > --- a/drivers/mtd/nand/gpmi-nand/bch-regs.h > +++ b/drivers/mtd/nand/gpmi-nand/bch-regs.h > @@ -51,15 +51,26 @@ > > #define BP_BCH_FLASH0LAYOUT0_ECC0 12 > #define BM_BCH_FLASH0LAYOUT0_ECC0 (0xf << BP_BCH_FLASH0LAYOUT0_ECC0) > -#define BF_BCH_FLASH0LAYOUT0_ECC0(v) \ > - (((v) << BP_BCH_FLASH0LAYOUT0_ECC0) & BM_BCH_FLASH0LAYOUT0_ECC0) > +#define MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0 11 > +#define MX6Q_BM_BCH_FLASH0LAYOUT0_ECC0 (0x1f << MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0) > +#define BF_BCH_FLASH0LAYOUT0_ECC0(v, x) \ > + (GPMI_IS_MX6Q(x) \ > + ? (((v) << MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0) \ > + & MX6Q_BM_BCH_FLASH0LAYOUT0_ECC0) \ > + : (((v) << BP_BCH_FLASH0LAYOUT0_ECC0) \ > + & BM_BCH_FLASH0LAYOUT0_ECC0) \ > + ) > > #define BP_BCH_FLASH0LAYOUT0_DATA0_SIZE 0 > #define BM_BCH_FLASH0LAYOUT0_DATA0_SIZE \ > (0xfff << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE) > -#define BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(v) \ > - (((v) << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE)\ > - & BM_BCH_FLASH0LAYOUT0_DATA0_SIZE) > +#define MX6Q_BM_BCH_FLASH0LAYOUT0_DATA0_SIZE \ > + (0x3ff << BP_BCH_FLASH0LAYOUT0_DATA0_SIZE) > +#define BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(v, x) \ > + (GPMI_IS_MX6Q(x) \ > + ? (((v) >> 2) & MX6Q_BM_BCH_FLASH0LAYOUT0_DATA0_SIZE) \ > + : ((v) & BM_BCH_FLASH0LAYOUT0_DATA0_SIZE) \ > + ) > > #define HW_BCH_FLASH0LAYOUT1 0x00000090 > > @@ -72,13 +83,24 @@ > > #define BP_BCH_FLASH0LAYOUT1_ECCN 12 > #define BM_BCH_FLASH0LAYOUT1_ECCN (0xf << BP_BCH_FLASH0LAYOUT1_ECCN) > -#define BF_BCH_FLASH0LAYOUT1_ECCN(v) \ > - (((v) << BP_BCH_FLASH0LAYOUT1_ECCN) & BM_BCH_FLASH0LAYOUT1_ECCN) > +#define MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN 11 > +#define MX6Q_BM_BCH_FLASH0LAYOUT1_ECCN (0x1f << MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN) > +#define BF_BCH_FLASH0LAYOUT1_ECCN(v, x) \ > + (GPMI_IS_MX6Q(x) \ > + ? (((v) << MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN) \ > + & MX6Q_BM_BCH_FLASH0LAYOUT1_ECCN) \ > + : (((v) << BP_BCH_FLASH0LAYOUT1_ECCN) \ > + & BM_BCH_FLASH0LAYOUT1_ECCN) \ > + ) > > #define BP_BCH_FLASH0LAYOUT1_DATAN_SIZE 0 > #define BM_BCH_FLASH0LAYOUT1_DATAN_SIZE \ > (0xfff << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE) > -#define BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(v) \ > - (((v) << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE) \ > - & BM_BCH_FLASH0LAYOUT1_DATAN_SIZE) > +#define MX6Q_BM_BCH_FLASH0LAYOUT1_DATAN_SIZE \ > + (0x3ff << BP_BCH_FLASH0LAYOUT1_DATAN_SIZE) > +#define BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(v, x) \ > + (GPMI_IS_MX6Q(x) \ > + ? (((v) >> 2) & MX6Q_BM_BCH_FLASH0LAYOUT1_DATAN_SIZE) \ > + : ((v) & BM_BCH_FLASH0LAYOUT1_DATAN_SIZE) \ > + ) > #endif > diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c > index fa5200b..a1f4332 100644 > --- a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c > +++ b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c > @@ -224,13 +224,13 @@ int bch_set_geometry(struct gpmi_nand_data *this) > /* Configure layout 0. */ > writel(BF_BCH_FLASH0LAYOUT0_NBLOCKS(block_count) > | BF_BCH_FLASH0LAYOUT0_META_SIZE(metadata_size) > - | BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength) > - | BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size), > + | BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength, this) > + | BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size, this), > r->bch_regs + HW_BCH_FLASH0LAYOUT0); > > writel(BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(page_size) > - | BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength) > - | BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size), > + | BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength, this) > + | BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size, this), > r->bch_regs + HW_BCH_FLASH0LAYOUT1); > > /* Set *all* chip selects to use layout 0. */ > @@ -256,11 +256,12 @@ static unsigned int ns_to_cycles(unsigned int time, > return max(k, min); > } > > +#define DEF_MIN_PROP_DELAY 5 > +#define DEF_MAX_PROP_DELAY 9 > /* Apply timing to current hardware conditions. */ > static int gpmi_nfc_compute_hardware_timing(struct gpmi_nand_data *this, > struct gpmi_nfc_hardware_timing *hw) > { > - struct gpmi_nand_platform_data *pdata = this->pdata; > struct timing_threshod *nfc = &timing_default_threshold; > struct nand_chip *nand = &this->nand; > struct nand_timing target = this->timing; > @@ -277,8 +278,8 @@ static int gpmi_nfc_compute_hardware_timing(struct gpmi_nand_data *this, > int ideal_sample_delay_in_ns; > unsigned int sample_delay_factor; > int tEYE; > - unsigned int min_prop_delay_in_ns = pdata->min_prop_delay_in_ns; > - unsigned int max_prop_delay_in_ns = pdata->max_prop_delay_in_ns; > + unsigned int min_prop_delay_in_ns = DEF_MIN_PROP_DELAY; > + unsigned int max_prop_delay_in_ns = DEF_MAX_PROP_DELAY; > > /* > * If there are multiple chips, we need to relax the timings to allow > @@ -804,7 +805,8 @@ int gpmi_is_ready(struct gpmi_nand_data *this, unsigned chip) > if (GPMI_IS_MX23(this)) { > mask = MX23_BM_GPMI_DEBUG_READY0 << chip; > reg = readl(r->gpmi_regs + HW_GPMI_DEBUG); > - } else if (GPMI_IS_MX28(this)) { > + } else if (GPMI_IS_MX28(this) || GPMI_IS_MX6Q(this)) { > + /* MX28 shares the same R/B register as MX6Q. */ > mask = MX28_BF_GPMI_STAT_READY_BUSY(1 << chip); > reg = readl(r->gpmi_regs + HW_GPMI_STAT); > } else > diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c > index 75b1dde..5c6af5d 100644 > --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c > +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c > @@ -24,6 +24,9 @@ > #include <linux/module.h> > #include <linux/mtd/gpmi-nand.h> > #include <linux/mtd/partitions.h> > +#include <linux/of_address.h> > +#include <linux/of_device.h> > +#include <linux/of_irq.h> > #include "gpmi-nand.h" > > /* add our owner bbt descriptor */ > @@ -306,36 +309,6 @@ int start_dma_with_bch_irq(struct gpmi_nand_data *this, > return 0; > } > > -static int __devinit > -acquire_register_block(struct gpmi_nand_data *this, const char *res_name) > -{ > - struct platform_device *pdev = this->pdev; > - struct resources *res = &this->resources; > - struct resource *r; > - void *p; > - > - r = platform_get_resource_byname(pdev, IORESOURCE_MEM, res_name); > - if (!r) { > - pr_err("Can't get resource for %s\n", res_name); > - return -ENXIO; > - } > - > - p = ioremap(r->start, resource_size(r)); > - if (!p) { > - pr_err("Can't remap %s\n", res_name); > - return -ENOMEM; > - } > - > - if (!strcmp(res_name, GPMI_NAND_GPMI_REGS_ADDR_RES_NAME)) > - res->gpmi_regs = p; > - else if (!strcmp(res_name, GPMI_NAND_BCH_REGS_ADDR_RES_NAME)) > - res->bch_regs = p; > - else > - pr_err("unknown resource name : %s\n", res_name); > - > - return 0; > -} > - I think the patch goes to a wrong way for acquiring resources from device tree. You need to have a look at Documentation/devicetree/bindings/resource-names.txt and understand that DT core has populated the resources for device, and device driver can call the same suite of functions to retrieve the resources. That said device driver does not need any change on resource acquiring for device tree probe at all. Regards, Shawn > static void release_register_block(struct gpmi_nand_data *this) > { > struct resources *res = &this->resources; > @@ -347,32 +320,6 @@ static void release_register_block(struct gpmi_nand_data *this) > res->bch_regs = NULL; > } > > -static int __devinit > -acquire_bch_irq(struct gpmi_nand_data *this, irq_handler_t irq_h) > -{ > - struct platform_device *pdev = this->pdev; > - struct resources *res = &this->resources; > - const char *res_name = GPMI_NAND_BCH_INTERRUPT_RES_NAME; > - struct resource *r; > - int err; > - > - r = platform_get_resource_byname(pdev, IORESOURCE_IRQ, res_name); > - if (!r) { > - pr_err("Can't get resource for %s\n", res_name); > - return -ENXIO; > - } > - > - err = request_irq(r->start, irq_h, 0, res_name, this); > - if (err) { > - pr_err("Can't own %s\n", res_name); > - return err; > - } > - > - res->bch_low_interrupt = r->start; > - res->bch_high_interrupt = r->end; > - return 0; > -} > - > static void release_bch_irq(struct gpmi_nand_data *this) > { > struct resources *res = &this->resources; > @@ -385,7 +332,7 @@ static void release_bch_irq(struct gpmi_nand_data *this) > static bool gpmi_dma_filter(struct dma_chan *chan, void *param) > { > struct gpmi_nand_data *this = param; > - struct resource *r = this->private; > + int dma_channel = (int)this->private; > > if (!mxs_dma_is_apbh(chan)) > return false; > @@ -397,7 +344,7 @@ static bool gpmi_dma_filter(struct dma_chan *chan, void *param) > * for mx28 : MX28_DMA_GPMI0 ~ MX28_DMA_GPMI7 > * (These eight channels share the same IRQ!) > */ > - if (r->start <= chan->chan_id && chan->chan_id <= r->end) { > + if (dma_channel == chan->chan_id) { > chan->private = &this->dma_data; > return true; > } > @@ -414,85 +361,91 @@ static void release_dma_channels(struct gpmi_nand_data *this) > } > } > > -static int __devinit acquire_dma_channels(struct gpmi_nand_data *this) > +static const char *bch_node_name[] __devinitconst = { > + [IS_MX23] = "fsl,imx23-bch", > + [IS_MX28] = "fsl,imx28-bch", > + [IS_MX6Q] = "fsl,imx6q-bch", > +}; > + > +static int __devinit acquire_resources(struct gpmi_nand_data *this) > { > - struct platform_device *pdev = this->pdev; > - struct gpmi_nand_platform_data *pdata = this->pdata; > struct resources *res = &this->resources; > - struct resource *r, *r_dma; > - unsigned int i; > + struct platform_device *pdev = this->pdev; > + struct resource *r; > + struct device_node *dn; > + unsigned int irq; > + int ret = -EINVAL; > + > + /* gpmi */ > + r = platform_get_resource(pdev, IORESOURCE_MEM, 0); > + if (!r) { > + pr_err("Can't get gpmi resource.\n"); > + goto exit_regs; > + } > > - r = platform_get_resource_byname(pdev, IORESOURCE_DMA, > - GPMI_NAND_DMA_CHANNELS_RES_NAME); > - r_dma = platform_get_resource_byname(pdev, IORESOURCE_IRQ, > - GPMI_NAND_DMA_INTERRUPT_RES_NAME); > - if (!r || !r_dma) { > - pr_err("Can't get resource for DMA\n"); > - return -ENXIO; > + res->gpmi_regs = ioremap(r->start, resource_size(r)); > + if (!res->gpmi_regs) { > + pr_err("Can't remap for gpmi.\n"); > + goto exit_regs; > } > > - /* used in gpmi_dma_filter() */ > - this->private = r; > + /* bch */ > + dn = of_find_compatible_node(NULL, NULL, > + bch_node_name[pdev->id_entry->driver_data]); > + if (dn) { > + res->bch_regs = of_iomap(dn, 0); > + if (!res->bch_regs) { > + of_node_put(dn); > + goto exit_regs; > + } > + } else { > + pr_err("Can't find device node for BCH.\n"); > + goto exit_regs; > + } > > - for (i = r->start; i <= r->end; i++) { > + irq = irq_of_parse_and_map(dn, 0); > + ret = request_irq(irq, bch_irq, 0, NULL, this); > + if (ret) { > + of_node_put(dn); > + pr_err("interrupt request failed\n"); > + goto exit_regs; > + } > + res->bch_low_interrupt = res->bch_high_interrupt = irq; > + of_node_put(dn); > + > + /* apbh-dma channel */ > + r = platform_get_resource(pdev, IORESOURCE_IRQ, 0); > + if (r) { > struct dma_chan *dma_chan; > dma_cap_mask_t mask; > - > - if (i - r->start >= pdata->max_chip_count) > - break; > + int dma_channel; > > dma_cap_zero(mask); > dma_cap_set(DMA_SLAVE, mask); > > - /* get the DMA interrupt */ > - if (r_dma->start == r_dma->end) { > - /* only register the first. */ > - if (i == r->start) > - this->dma_data.chan_irq = r_dma->start; > - else > - this->dma_data.chan_irq = NO_IRQ; > - } else > - this->dma_data.chan_irq = r_dma->start + (i - r->start); > - > - dma_chan = dma_request_channel(mask, gpmi_dma_filter, this); > - if (!dma_chan) > - goto acquire_err; > - > - /* fill the first empty item */ > - this->dma_chans[i - r->start] = dma_chan; > - } > - > - res->dma_low_channel = r->start; > - res->dma_high_channel = i; > - return 0; > - > -acquire_err: > - pr_err("Can't acquire DMA channel %u\n", i); > - release_dma_channels(this); > - return -EINVAL; > -} > - > -static int __devinit acquire_resources(struct gpmi_nand_data *this) > -{ > - struct resources *res = &this->resources; > - int ret; > - > - ret = acquire_register_block(this, GPMI_NAND_GPMI_REGS_ADDR_RES_NAME); > - if (ret) > - goto exit_regs; > - > - ret = acquire_register_block(this, GPMI_NAND_BCH_REGS_ADDR_RES_NAME); > - if (ret) > - goto exit_regs; > + this->dma_data.chan_irq = r->start; > > - ret = acquire_bch_irq(this, bch_irq); > - if (ret) > - goto exit_regs; > + /* We only support one chip now, so we need one DMA channel.*/ > + dn = pdev->dev.of_node; > + ret = of_property_read_u32(dn, "dma_channel", &dma_channel); > + if (ret) { > + pr_err("unable to get DMA channel from dt.\n"); > + goto exit_dma_channels; > + } > + this->private = (void *)dma_channel; > > - ret = acquire_dma_channels(this); > - if (ret) > + dma_chan = dma_request_channel(mask, gpmi_dma_filter, this); > + if (!dma_chan) { > + pr_err("dma_request_channel failed.\n"); > + goto exit_dma_channels; > + } > + this->dma_chans[0] = dma_chan; > + } else { > + pr_err("Can't find irq for dma\n"); > goto exit_dma_channels; > + } > > + /* gpmi clock */ > res->clock = clk_get(&this->pdev->dev, NULL); > if (IS_ERR(res->clock)) { > pr_err("can not get the clock\n"); > @@ -1461,7 +1414,6 @@ void gpmi_nfc_exit(struct gpmi_nand_data *this) > > static int __devinit gpmi_nfc_init(struct gpmi_nand_data *this) > { > - struct gpmi_nand_platform_data *pdata = this->pdata; > struct mtd_info *mtd = &this->mtd; > struct nand_chip *chip = &this->nand; > int ret; > @@ -1501,14 +1453,13 @@ static int __devinit gpmi_nfc_init(struct gpmi_nand_data *this) > if (ret) > goto err_out; > > - ret = nand_scan(mtd, pdata->max_chip_count); > + ret = nand_scan(mtd, 1); > if (ret) { > pr_err("Chip scan failed\n"); > goto err_out; > } > > - ret = mtd_device_parse_register(mtd, NULL, NULL, > - pdata->partitions, pdata->partition_count); > + ret = mtd_device_parse_register(mtd, NULL, NULL, NULL, 0); > if (ret) > goto err_out; > return 0; > @@ -1518,12 +1469,38 @@ err_out: > return ret; > } > > +static const struct platform_device_id gpmi_ids[] = { > + { .name = "imx23-gpmi-nand", .driver_data = IS_MX23, }, > + { .name = "imx28-gpmi-nand", .driver_data = IS_MX28, }, > + { .name = "imx6q-gpmi-nand", .driver_data = IS_MX6Q, }, > + {}, > +}; > + > +static const struct of_device_id gpmi_nand_id_table[] = { > + { > + .compatible = "fsl,imx23-gpmi-nand", > + .data = (void *)&gpmi_ids[IS_MX23] > + }, { > + .compatible = "fsl,imx28-gpmi-nand", > + .data = (void *)&gpmi_ids[IS_MX28] > + }, { > + .compatible = "fsl,imx6q-gpmi-nand", > + .data = (void *)&gpmi_ids[IS_MX6Q] > + }, {} > +}; > +MODULE_DEVICE_TABLE(of, gpmi_nand_id_table); > + > static int __devinit gpmi_nand_probe(struct platform_device *pdev) > { > struct gpmi_nand_platform_data *pdata = pdev->dev.platform_data; > struct gpmi_nand_data *this; > + const struct of_device_id *of_id; > int ret; > > + of_id = of_match_device(gpmi_nand_id_table, &pdev->dev); > + if (of_id) > + pdev->id_entry = of_id->data; > + > this = kzalloc(sizeof(*this), GFP_KERNEL); > if (!this) { > pr_err("Failed to allocate per-device memory\n"); > @@ -1535,7 +1512,7 @@ static int __devinit gpmi_nand_probe(struct platform_device *pdev) > this->dev = &pdev->dev; > this->pdata = pdata; > > - if (pdata->platform_init) { > + if (pdata && pdata->platform_init) { > ret = pdata->platform_init(); > if (ret) > goto platform_init_error; > @@ -1575,19 +1552,10 @@ static int __exit gpmi_nand_remove(struct platform_device *pdev) > return 0; > } > > -static const struct platform_device_id gpmi_ids[] = { > - { > - .name = "imx23-gpmi-nand", > - .driver_data = IS_MX23, > - }, { > - .name = "imx28-gpmi-nand", > - .driver_data = IS_MX28, > - }, {}, > -}; > - > static struct platform_driver gpmi_nand_driver = { > .driver = { > .name = "gpmi-nand", > + .of_match_table = gpmi_nand_id_table, > }, > .probe = gpmi_nand_probe, > .remove = __exit_p(gpmi_nand_remove), > diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.h b/drivers/mtd/nand/gpmi-nand/gpmi-nand.h > index ec6180d..ce5daa1 100644 > --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.h > +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.h > @@ -266,8 +266,10 @@ extern int gpmi_read_page(struct gpmi_nand_data *, > #define STATUS_UNCORRECTABLE 0xfe > > /* Use the platform_id to distinguish different Archs. */ > -#define IS_MX23 0x1 > -#define IS_MX28 0x2 > +#define IS_MX23 0x0 > +#define IS_MX28 0x1 > +#define IS_MX6Q 0x2 > #define GPMI_IS_MX23(x) ((x)->pdev->id_entry->driver_data == IS_MX23) > #define GPMI_IS_MX28(x) ((x)->pdev->id_entry->driver_data == IS_MX28) > +#define GPMI_IS_MX6Q(x) ((x)->pdev->id_entry->driver_data == IS_MX6Q) > #endif > -- > 1.7.0.4 > > ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 3/3] mtd: gpmi: add device tree support for mx6q-arm2 and mx28evk 2012-04-23 6:43 ` Shawn Guo @ 2012-04-23 8:10 ` Huang Shijie 2012-04-23 13:05 ` Shawn Guo 0 siblings, 1 reply; 10+ messages in thread From: Huang Shijie @ 2012-04-23 8:10 UTC (permalink / raw) To: linux-arm-kernel ? 2012?04?23? 14:43, Shawn Guo ??: > On Fri, Apr 20, 2012 at 05:24:19PM +0800, Huang Shijie wrote: >> add DT support to mx6q-arm2 and mx28evk. >> > Again, this is not a support about board but soc. > thanks. I will change it in next version. >> Signed-off-by: Huang Shijie<b32955@freescale.com> >> --- >> .../devicetree/bindings/mtd/gpmi-nand.txt | 30 +++ >> drivers/mtd/nand/Kconfig | 2 +- >> drivers/mtd/nand/gpmi-nand/bch-regs.h | 42 +++- >> drivers/mtd/nand/gpmi-nand/gpmi-lib.c | 18 +- >> drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 240 +++++++++----------- >> drivers/mtd/nand/gpmi-nand/gpmi-nand.h | 6 +- >> 6 files changed, 181 insertions(+), 157 deletions(-) >> create mode 100644 Documentation/devicetree/bindings/mtd/gpmi-nand.txt >> >> diff --git a/Documentation/devicetree/bindings/mtd/gpmi-nand.txt b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt >> new file mode 100644 >> index 0000000..e1181ee >> --- /dev/null >> +++ b/Documentation/devicetree/bindings/mtd/gpmi-nand.txt >> @@ -0,0 +1,30 @@ >> +* Freescale General-Purpose Media Interface (GPMI) >> + >> +The GPMI nand controller provides an interface to control the >> +NAND flash chips. We support only one NAND chips now. >> + >> +The GPMI nand controller required properties: >> + - compatible : should be "fsl,<chip>-gpmi-nand" >> + - reg : should contain registers location and length. >> + - interrupts : should contain the DMA interrupt number for GPMI. >> + We do not use the GPMI interrupt. >> + - dma_channel: Should contain the dma channel it uses. >> + >> +The BCH required properties: >> + - compatible : should be "fsl,<chip>-bch" >> + - reg : should contain registers location and length. >> + - interrupts : should contain the BCH interrupt. >> + >> +Examples: >> + >> +gpmi-nand at 8000c000 { >> + compatible = "fsl,imx28-gpmi-nand"; >> + reg =<0x8000c000 2000>; >> + interrupts =<88>; >> + dma_channel =<4>; > Before generic dma helper is available, do not use such generic property > name, and use something like "fsl,gpmi-dma-events". Yes, "-" rather > than "_" should be used in property name. > got it. >> +}; >> +bch at 8000a000 { >> + compatible = "fsl,imx28-bch"; >> + reg =<0x8000a000 2000>; >> + interrupts =<41>; >> +}; >> diff --git a/drivers/mtd/nand/Kconfig b/drivers/mtd/nand/Kconfig >> index 7d17cec..bf0a28d 100644 >> --- a/drivers/mtd/nand/Kconfig >> +++ b/drivers/mtd/nand/Kconfig >> @@ -440,7 +440,7 @@ config MTD_NAND_NANDSIM >> >> config MTD_NAND_GPMI_NAND >> bool "GPMI NAND Flash Controller driver" >> - depends on MTD_NAND&& (SOC_IMX23 || SOC_IMX28) >> + depends on MTD_NAND&& (SOC_IMX23 || SOC_IMX28 || SOC_IMX6Q) >> help >> Enables NAND Flash support for IMX23 or IMX28. >> The GPMI controller is very powerful, with the help of BCH >> diff --git a/drivers/mtd/nand/gpmi-nand/bch-regs.h b/drivers/mtd/nand/gpmi-nand/bch-regs.h >> index 4effb8c..a092451 100644 >> --- a/drivers/mtd/nand/gpmi-nand/bch-regs.h >> +++ b/drivers/mtd/nand/gpmi-nand/bch-regs.h >> @@ -51,15 +51,26 @@ >> >> #define BP_BCH_FLASH0LAYOUT0_ECC0 12 >> #define BM_BCH_FLASH0LAYOUT0_ECC0 (0xf<< BP_BCH_FLASH0LAYOUT0_ECC0) >> -#define BF_BCH_FLASH0LAYOUT0_ECC0(v) \ >> - (((v)<< BP_BCH_FLASH0LAYOUT0_ECC0)& BM_BCH_FLASH0LAYOUT0_ECC0) >> +#define MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0 11 >> +#define MX6Q_BM_BCH_FLASH0LAYOUT0_ECC0 (0x1f<< MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0) >> +#define BF_BCH_FLASH0LAYOUT0_ECC0(v, x) \ >> + (GPMI_IS_MX6Q(x) \ >> + ? (((v)<< MX6Q_BP_BCH_FLASH0LAYOUT0_ECC0) \ >> + & MX6Q_BM_BCH_FLASH0LAYOUT0_ECC0) \ >> + : (((v)<< BP_BCH_FLASH0LAYOUT0_ECC0) \ >> + & BM_BCH_FLASH0LAYOUT0_ECC0) \ >> + ) >> >> #define BP_BCH_FLASH0LAYOUT0_DATA0_SIZE 0 >> #define BM_BCH_FLASH0LAYOUT0_DATA0_SIZE \ >> (0xfff<< BP_BCH_FLASH0LAYOUT0_DATA0_SIZE) >> -#define BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(v) \ >> - (((v)<< BP_BCH_FLASH0LAYOUT0_DATA0_SIZE)\ >> - & BM_BCH_FLASH0LAYOUT0_DATA0_SIZE) >> +#define MX6Q_BM_BCH_FLASH0LAYOUT0_DATA0_SIZE \ >> + (0x3ff<< BP_BCH_FLASH0LAYOUT0_DATA0_SIZE) >> +#define BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(v, x) \ >> + (GPMI_IS_MX6Q(x) \ >> + ? (((v)>> 2)& MX6Q_BM_BCH_FLASH0LAYOUT0_DATA0_SIZE) \ >> + : ((v)& BM_BCH_FLASH0LAYOUT0_DATA0_SIZE) \ >> + ) >> >> #define HW_BCH_FLASH0LAYOUT1 0x00000090 >> >> @@ -72,13 +83,24 @@ >> >> #define BP_BCH_FLASH0LAYOUT1_ECCN 12 >> #define BM_BCH_FLASH0LAYOUT1_ECCN (0xf<< BP_BCH_FLASH0LAYOUT1_ECCN) >> -#define BF_BCH_FLASH0LAYOUT1_ECCN(v) \ >> - (((v)<< BP_BCH_FLASH0LAYOUT1_ECCN)& BM_BCH_FLASH0LAYOUT1_ECCN) >> +#define MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN 11 >> +#define MX6Q_BM_BCH_FLASH0LAYOUT1_ECCN (0x1f<< MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN) >> +#define BF_BCH_FLASH0LAYOUT1_ECCN(v, x) \ >> + (GPMI_IS_MX6Q(x) \ >> + ? (((v)<< MX6Q_BP_BCH_FLASH0LAYOUT1_ECCN) \ >> + & MX6Q_BM_BCH_FLASH0LAYOUT1_ECCN) \ >> + : (((v)<< BP_BCH_FLASH0LAYOUT1_ECCN) \ >> + & BM_BCH_FLASH0LAYOUT1_ECCN) \ >> + ) >> >> #define BP_BCH_FLASH0LAYOUT1_DATAN_SIZE 0 >> #define BM_BCH_FLASH0LAYOUT1_DATAN_SIZE \ >> (0xfff<< BP_BCH_FLASH0LAYOUT1_DATAN_SIZE) >> -#define BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(v) \ >> - (((v)<< BP_BCH_FLASH0LAYOUT1_DATAN_SIZE) \ >> - & BM_BCH_FLASH0LAYOUT1_DATAN_SIZE) >> +#define MX6Q_BM_BCH_FLASH0LAYOUT1_DATAN_SIZE \ >> + (0x3ff<< BP_BCH_FLASH0LAYOUT1_DATAN_SIZE) >> +#define BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(v, x) \ >> + (GPMI_IS_MX6Q(x) \ >> + ? (((v)>> 2)& MX6Q_BM_BCH_FLASH0LAYOUT1_DATAN_SIZE) \ >> + : ((v)& BM_BCH_FLASH0LAYOUT1_DATAN_SIZE) \ >> + ) >> #endif >> diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c >> index fa5200b..a1f4332 100644 >> --- a/drivers/mtd/nand/gpmi-nand/gpmi-lib.c >> +++ b/drivers/mtd/nand/gpmi-nand/gpmi-lib.c >> @@ -224,13 +224,13 @@ int bch_set_geometry(struct gpmi_nand_data *this) >> /* Configure layout 0. */ >> writel(BF_BCH_FLASH0LAYOUT0_NBLOCKS(block_count) >> | BF_BCH_FLASH0LAYOUT0_META_SIZE(metadata_size) >> - | BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength) >> - | BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size), >> + | BF_BCH_FLASH0LAYOUT0_ECC0(ecc_strength, this) >> + | BF_BCH_FLASH0LAYOUT0_DATA0_SIZE(block_size, this), >> r->bch_regs + HW_BCH_FLASH0LAYOUT0); >> >> writel(BF_BCH_FLASH0LAYOUT1_PAGE_SIZE(page_size) >> - | BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength) >> - | BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size), >> + | BF_BCH_FLASH0LAYOUT1_ECCN(ecc_strength, this) >> + | BF_BCH_FLASH0LAYOUT1_DATAN_SIZE(block_size, this), >> r->bch_regs + HW_BCH_FLASH0LAYOUT1); >> >> /* Set *all* chip selects to use layout 0. */ >> @@ -256,11 +256,12 @@ static unsigned int ns_to_cycles(unsigned int time, >> return max(k, min); >> } >> >> +#define DEF_MIN_PROP_DELAY 5 >> +#define DEF_MAX_PROP_DELAY 9 >> /* Apply timing to current hardware conditions. */ >> static int gpmi_nfc_compute_hardware_timing(struct gpmi_nand_data *this, >> struct gpmi_nfc_hardware_timing *hw) >> { >> - struct gpmi_nand_platform_data *pdata = this->pdata; >> struct timing_threshod *nfc =&timing_default_threshold; >> struct nand_chip *nand =&this->nand; >> struct nand_timing target = this->timing; >> @@ -277,8 +278,8 @@ static int gpmi_nfc_compute_hardware_timing(struct gpmi_nand_data *this, >> int ideal_sample_delay_in_ns; >> unsigned int sample_delay_factor; >> int tEYE; >> - unsigned int min_prop_delay_in_ns = pdata->min_prop_delay_in_ns; >> - unsigned int max_prop_delay_in_ns = pdata->max_prop_delay_in_ns; >> + unsigned int min_prop_delay_in_ns = DEF_MIN_PROP_DELAY; >> + unsigned int max_prop_delay_in_ns = DEF_MAX_PROP_DELAY; >> >> /* >> * If there are multiple chips, we need to relax the timings to allow >> @@ -804,7 +805,8 @@ int gpmi_is_ready(struct gpmi_nand_data *this, unsigned chip) >> if (GPMI_IS_MX23(this)) { >> mask = MX23_BM_GPMI_DEBUG_READY0<< chip; >> reg = readl(r->gpmi_regs + HW_GPMI_DEBUG); >> - } else if (GPMI_IS_MX28(this)) { >> + } else if (GPMI_IS_MX28(this) || GPMI_IS_MX6Q(this)) { >> + /* MX28 shares the same R/B register as MX6Q. */ >> mask = MX28_BF_GPMI_STAT_READY_BUSY(1<< chip); >> reg = readl(r->gpmi_regs + HW_GPMI_STAT); >> } else >> diff --git a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c >> index 75b1dde..5c6af5d 100644 >> --- a/drivers/mtd/nand/gpmi-nand/gpmi-nand.c >> +++ b/drivers/mtd/nand/gpmi-nand/gpmi-nand.c >> @@ -24,6 +24,9 @@ >> #include<linux/module.h> >> #include<linux/mtd/gpmi-nand.h> >> #include<linux/mtd/partitions.h> >> +#include<linux/of_address.h> >> +#include<linux/of_device.h> >> +#include<linux/of_irq.h> >> #include "gpmi-nand.h" >> >> /* add our owner bbt descriptor */ >> @@ -306,36 +309,6 @@ int start_dma_with_bch_irq(struct gpmi_nand_data *this, >> return 0; >> } >> >> -static int __devinit >> -acquire_register_block(struct gpmi_nand_data *this, const char *res_name) >> -{ >> - struct platform_device *pdev = this->pdev; >> - struct resources *res =&this->resources; >> - struct resource *r; >> - void *p; >> - >> - r = platform_get_resource_byname(pdev, IORESOURCE_MEM, res_name); >> - if (!r) { >> - pr_err("Can't get resource for %s\n", res_name); >> - return -ENXIO; >> - } >> - >> - p = ioremap(r->start, resource_size(r)); >> - if (!p) { >> - pr_err("Can't remap %s\n", res_name); >> - return -ENOMEM; >> - } >> - >> - if (!strcmp(res_name, GPMI_NAND_GPMI_REGS_ADDR_RES_NAME)) >> - res->gpmi_regs = p; >> - else if (!strcmp(res_name, GPMI_NAND_BCH_REGS_ADDR_RES_NAME)) >> - res->bch_regs = p; >> - else >> - pr_err("unknown resource name : %s\n", res_name); >> - >> - return 0; >> -} >> - > I think the patch goes to a wrong way for acquiring resources from > device tree. > > You need to have a look at Documentation/devicetree/bindings/resource-names.txt > and understand that DT core has populated the resources for device, > and device driver can call the same suite of functions to retrieve Do you mean I can merge the gpmi and bch into one device node such as : gpmi-nand at xx { compatible = "fsl, mx28-gpmi-nand"; reg = <xx>, <xx>; reg-names = "gpmi", "bch"; }; Best Regards Huang Shijie > the resources. That said device driver does not need any change on > resource acquiring for device tree probe at all. > > Regards, > Shawn > ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 3/3] mtd: gpmi: add device tree support for mx6q-arm2 and mx28evk 2012-04-23 8:10 ` Huang Shijie @ 2012-04-23 13:05 ` Shawn Guo 0 siblings, 0 replies; 10+ messages in thread From: Shawn Guo @ 2012-04-23 13:05 UTC (permalink / raw) To: linux-arm-kernel On Mon, Apr 23, 2012 at 04:10:41PM +0800, Huang Shijie wrote: > Do you mean I can merge the gpmi and bch into one device node such as : > > gpmi-nand at xx { > compatible = "fsl, mx28-gpmi-nand"; > reg = <xx>, <xx>; > reg-names = "gpmi", "bch"; > > }; > Yes. But you need to redefine GPMI_NAND_GPMI_REGS_ADDR_RES_NAME as "gpmi" and GPMI_NAND_BCH_REGS_ADDR_RES_NAME as "bch". That said, the strings here must match the ones used in driver. -- Regards, Shawn ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH 0/3] add gpmi-nand dt support for mx6q-arm2 and imx28evk 2012-04-20 9:24 [PATCH 0/3] add gpmi-nand dt support for mx6q-arm2 and imx28evk Huang Shijie ` (2 preceding siblings ...) 2012-04-20 9:24 ` [PATCH 3/3] mtd: gpmi: add device tree support for mx6q-arm2 and mx28evk Huang Shijie @ 2012-04-23 5:26 ` Shawn Guo 3 siblings, 0 replies; 10+ messages in thread From: Shawn Guo @ 2012-04-23 5:26 UTC (permalink / raw) To: linux-arm-kernel On Fri, Apr 20, 2012 at 05:24:16PM +0800, Huang Shijie wrote: > The mx6q-arm2 and imx28evk have already support the device tree now. > So i decide to add the gpmi-nand dt support to them. > > The mx23 does not support the device tree now. I will add the gpmi dt support > when it is ready. > > Test this patch set on both MX6Q-arm2 and mx28evk. > > Huang Shijie (3): > ARM: mx6q-arm2: add gpmi-nand dt support > ARM: mx28evk: add gpmi-nand dt support > mtd: gpmi: add device tree support for mx6q-arm2 and mx28evk I think the patch "mtd: gpmi: ..." needs to be the first one. Also, the support is not board but soc specific, so it really should not have board name in the patch subject. Regards, Shawn > > .../devicetree/bindings/mtd/gpmi-nand.txt | 30 +++ > arch/arm/boot/dts/imx28.dtsi | 9 +- > arch/arm/boot/dts/imx6q.dtsi | 12 + > arch/arm/mach-imx/clock-imx6q.c | 5 +- > arch/arm/mach-mxs/clock-mx28.c | 2 +- > drivers/mtd/nand/Kconfig | 2 +- > drivers/mtd/nand/gpmi-nand/bch-regs.h | 42 +++- > drivers/mtd/nand/gpmi-nand/gpmi-lib.c | 18 +- > drivers/mtd/nand/gpmi-nand/gpmi-nand.c | 240 +++++++++----------- > drivers/mtd/nand/gpmi-nand/gpmi-nand.h | 6 +- > 10 files changed, 202 insertions(+), 164 deletions(-) > create mode 100644 Documentation/devicetree/bindings/mtd/gpmi-nand.txt > > ^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2012-04-23 13:05 UTC | newest] Thread overview: 10+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2012-04-20 9:24 [PATCH 0/3] add gpmi-nand dt support for mx6q-arm2 and imx28evk Huang Shijie 2012-04-20 9:24 ` [PATCH 1/3] ARM: mx6q-arm2: add gpmi-nand dt support Huang Shijie 2012-04-23 5:35 ` Shawn Guo 2012-04-20 9:24 ` [PATCH 2/3] ARM: mx28evk: " Huang Shijie 2012-04-23 5:38 ` Shawn Guo 2012-04-20 9:24 ` [PATCH 3/3] mtd: gpmi: add device tree support for mx6q-arm2 and mx28evk Huang Shijie 2012-04-23 6:43 ` Shawn Guo 2012-04-23 8:10 ` Huang Shijie 2012-04-23 13:05 ` Shawn Guo 2012-04-23 5:26 ` [PATCH 0/3] add gpmi-nand dt support for mx6q-arm2 and imx28evk Shawn Guo
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).