Fwd: Re: [PATCH] mmc: at91: fix bus speed

[ludovic.desroches@atmel.com (ludovic.desroches)]

Hello Prchal,

Le 06/21/2012 09:56 AM, Prchal Ji?? a ?crit :
> Hello Ludovic,
> I have tried it with atmel-mci driver. It took me little time to change
> setting of my board.
> It seems to try clock down to 200kHz:
> [    5.860000] mmc0: mmc_rescan_try_freq: trying to init card at 400000 Hz
> [    5.920000] mmc0: mmc_rescan_try_freq: trying to init card at 300000 Hz
> [    5.980000] mmc0: mmc_rescan_try_freq: trying to init card at 205079 Hz
> As I see in driver source, there is better clkdiv overrun work around.

Yes it was well managed in this driver.

> But I don't find min and max freq definitions in this driver, it is
> probably somewhere else.

Into atmel_init_slot:
mmc->f_min = DIV_ROUND_UP(host->bus_hz, 512);
mmc->f_max = host->bus_hz / 2;

Regards

Ludovic

> So this would be OK.
>
> Dne 20.6.2012 11:13, ludovic.desroches napsal(a):
>> Add mmc mailing list.
>>
>>
>> -------- Message original --------
>> Sujet: Re: [PATCH] mmc: at91: fix bus speed
>> Date : Wed, 20 Jun 2012 10:49:08 +0200
>> De : ludovic.desroches <ludovic.desroches@atmel.com>
>> Pour : Prchal Ji?? <jiri.prchal@aksignal.cz>
>> Copie ? : <ludovic.desroches@atmel.com>,
>> <linux-arm-kernel@lists.infradead.org>
>>
>> Hello Jiri,
>>
>> Thanks for your patch but at91-mci is now deprecated and should be
>> removed in 3.7.
>> On one hand I don't know if we have to continue to take patches for this
>> driver, on the other hand it's a fix for some SD cards.
>>
>> Le 06/20/2012 10:15 AM, Prchal Ji?? a ?crit :
>>> This patch change minimum and maximum clock speed because some noname
>>> cards doesn't work during init even at 375kHz and new cards (SD v. 3.0)
>>> can run at 50 or 100 MHz.
>>> Also aded clkdiv register overrun fix when setting low speeds.
>>>
>>> Signed-off-by: Jiri Prchal <jiri.prchal@aksignal.cz>
>>> ---
>>>
>>> --- linux/linux-3.5-rc3/drivers/mmc/host/at91_mci.c.orig 2012-06-17
>>> 02:25:17.000000000 +0200
>>> +++ linux/linux-3.5-rc3/drivers/mmc/host/at91_mci.c 2012-06-18
>>> 11:01:49.751415984 +0200
>>> @@ -724,6 +724,10 @@ static void at91_mci_set_ios(struct mmc_
>>> else
>>> clkdiv = (at91_master_clock / ios->clock) / 2;
>>>
>>> + /* set maximum divider */
>>> + if (clkdiv > 255)
>>> + clkdiv = 255;
>>> +
>>> pr_debug("clkdiv = %d. mcck = %ld\n", clkdiv,
>>> at91_master_clock / (2 * (clkdiv + 1)));
>>> }
>>> @@ -948,8 +952,8 @@ static int __init at91_mci_probe(struct
>>> }
>>>
>>> mmc->ops = &at91_mci_ops;
>>> - mmc->f_min = 375000;
>>> - mmc->f_max = 25000000;
>>> + mmc->f_min = 200000; /* not all cards can run at 375kHz */
>>
>> I will check on atmel-mci if we have to decrease f_min.
>>
>>> + mmc->f_max = 100000000; /* new cards can run at 100MHz */
>>
>> MCI operates at a rate of up to master clock divided by two so you can't
>> reach 100MHz as max frequency since it means that our master clock is at
>> 200MHz that is not the case. I would say 50MHz is the maximum frequency
>> for product compatible with at91-mci.
>>
>>> mmc->ocr_avail = MMC_VDD_32_33 | MMC_VDD_33_34;
>>> mmc->caps = 0;
>>>
>>>
>>>
>>
>> Regards
>>
>> Ludovic
>>
>>
>>
>>
>>
>
>
>