usb, davinci: usb 2.0 problem on an am1808 based board

[hs@denx.de (Heiko Schocher)]

Hello Manjunathappa,

On 29.05.2012 16:22, Heiko Schocher wrote:
> Hello Manjunathappa,
>
> On 22.05.2012 09:22, Heiko Schocher wrote:
>> Hello Manjunathappa,
>>
>> Manjunathappa, Prakash wrote:
>>> Hi Heiko,
>>>
>>> On Mon, May 21, 2012 at 11:40:33, Heiko Schocher wrote:
>>>> Hello Manjunathappa,
>>>>
>>>> Manjunathappa, Prakash wrote:
>>>>> Hi Heiko,
>>>>>
>>>>> I do not know how putting delay helped MSC device detection.
>>>>> Can you please check if MUSB is coming up in "b_idle" state(by
>>>>> $cat /sys/devices/platform/musb-da8xx/musb-hdrc/mode)?
>>>>> State should move to b_peripheral on connecting gadget cable.
>>>> We have connected the USB0_ID pin to ground -> host only mode, so
>>>> I could not try this.
>>>>
>>>
>>> Ok, So it is coming up in which state, "$cat /sys/devices/platform/musb-da8xx/musb-hdrc/mode"?
>>
>> without the delay in da8xx_musb_interrupt() and the
>> + musb->a_wait_bcon = OTG_TIME_A_WAIT_BCON;
>> change:
>>
>> booting Linux with USB stick attached shows:
>> root at armv5te:~# cat /sys/devices/platform/musb-da8xx/musb-hdrc/mode
>> a_host
>> root at armv5te:~#
>>
>> booting Linux without USB stick attached:
>>
>> root at armv5te:~# cat /sys/devices/platform/musb-da8xx/musb-hdrc/mode
>> a_wait_vrise
>> root at armv5te:~#
>>
>> and connecting an usb stick:
>>
>> root at armv5te:~# cat /sys/devices/platform/musb-da8xx/musb-hdrc/mode
>> a_host
>> root at armv5te:~#
>>
>>>>> If you connect MSC device via mini-A connector, state should change to "a_host".
>>>>> OTG timer is responsible for above state changes, can you please check if below
>>>>> changes are present?
>>>>> diff --git a/drivers/usb/musb/da8xx.c b/drivers/usb/musb/da8xx.c index 4da7492..a1a692e 100644
>>>>> --- a/drivers/usb/musb/da8xx.c
>>>>> +++ b/drivers/usb/musb/da8xx.c
>>>>> @@ -76,6 +76,7 @@
>>>>> #define DA8XX_INTR_TX_SHIFT 0
>>>>> #define DA8XX_INTR_TX_MASK (DA8XX_USB_TX_EP_MASK<< DA8XX_INTR_TX_SHIFT)
>>>>>
>>>>> +#define A_WAIT_BCON_TIMEOUT 1100 /* in ms */
>>>>> #define DA8XX_MENTOR_CORE_OFFSET 0x400
>>>>>
>>>>> #define CFGCHIP2 IO_ADDRESS(DA8XX_SYSCFG0_BASE + DA8XX_CFGCHIP2_REG)
>>>>> @@ -443,6 +444,7 @@ static int da8xx_musb_init(struct musb *musb)
>>>>> rev, __raw_readl(CFGCHIP2),
>>>>> musb_readb(reg_base, DA8XX_USB_CTRL_REG));
>>>>>
>>>>> + musb->a_wait_bcon = A_WAIT_BCON_TIMEOUT;
>>>>> musb->isr = da8xx_musb_interrupt;
>>>>> return 0;
>>>>> fail:
>>>> No, this change is not in current mainline ...
>>>>
>>>> Added this patch, and I get:
>>>>
>>>> $ make -s uImage
>>>> drivers/usb/musb/da8xx.c: In function 'da8xx_musb_init':
>>>> drivers/usb/musb/da8xx.c:448:22: error: 'A_WAIT_BCON_TIMEOUT' undeclared (first use in this function)
>>>> drivers/usb/musb/da8xx.c:448:22: note: each undeclared identifier is reported only once for each function it appears in
>>>> make[3]: *** [drivers/usb/musb/da8xx.o] Error 1
>>>> make[2]: *** [drivers/usb/musb] Error 2
>>>> make[1]: *** [drivers/usb] Error 2
>>>> make: *** [drivers] Error 2
>>>> $
>>>>
>>>> Do you mean
>>>>
>>>> musb->a_wait_bcon = OTG_TIME_A_WAIT_BCON;
>>>>
>>>> ? This is setup in musb_core.c::allocate_instance() as Sergei Shtylyov
>>>> already commented ... nevertheless tried with this define your patch,
>>>> and my USB stick gets detected too...
>>>>
>>>
>>> Does that mean issue got fixed or Do you still have delay in da8xx_musb_interrupt handler?
>>
>> Without the delay in the da8xx_musb_interrupt() ...
>
> ping!
>
> How do we proceed here?

ping.

bye,
Heiko
-- 
DENX Software Engineering GmbH,     MD: Wolfgang Denk & Detlev Zundel
HRB 165235 Munich, Office: Kirchenstr.5, D-82194 Groebenzell, Germany