Panda ES board hang when using GPIO as interrupt

[frankyl@broadcom.com (Franky Lin)]

On 06/28/2012 03:59 PM, Jon Hunter wrote:
>
> On 06/28/2012 05:53 PM, Franky Lin wrote:
>> I found one interesting thing. When I added the print info to see when
>> runtime_suspend/resume get called, it seems like the suspend/resume is
>> unbalance during boot. Resume got called more than suspend. So I hack
>> the code to make sure suspend and resume are called in pair. A resume
>> without suspend will do nothing and return immediately. This also makes
>> the hang vanish.
>
> I am not 100% sure I follow. On boot I would expect to see a
> resume/suspend due to the probe on the irq bank and then I would expect
> to see another resume from the acquisition of the gpio, however, I would
> not expect a suspend until the gpio is freed, which I don't believe you
> are doing.
>
> Can you share your hack? Just paste the diff? This may help me
> understand more.
>

OK.
This is what I saw in the log:
[    0.171844] dummy:
[    0.172912] NET: Registered protocol family 16
[    0.173431] GPMC revision 6.0
[    0.173492] gpmc: irq-52 could not claim: err -22
[    0.177551] ??????omap_gpio_runtime_resume
[    0.178619] OMAP GPIO hardware version 0.1
[    0.178649] !!!!!omap_gpio_runtime_suspend
[    0.178771] ??????omap_gpio_runtime_resume
[    0.179351] !!!!!omap_gpio_runtime_suspend
[    0.179504] ??????omap_gpio_runtime_resume
[    0.180023] !!!!!omap_gpio_runtime_suspend
[    0.180145] ??????omap_gpio_runtime_resume
[    0.180694] !!!!!omap_gpio_runtime_suspend
[    0.180847] ??????omap_gpio_runtime_resume
[    0.181365] !!!!!omap_gpio_runtime_suspend
[    0.181518] ??????omap_gpio_runtime_resume
[    0.182037] !!!!!omap_gpio_runtime_suspend
[    0.185089] omap_mux_init: Add partition: #1: core, flags: 2
[    0.186462] omap_mux_init: Add partition: #2: wkup, flags: 2
[    0.186584] error setting wl12xx data: -38
[    0.189788] _omap_mux_get_by_name: Could not find signal 
uart1_rx.uart1_rx
[    0.189788] _omap_mux_get_by_name: Could not find signal 
uart1_rx.uart1_rx
[    0.239501] ??????omap_gpio_runtime_resume
[    0.239532] ??????omap_gpio_runtime_resume
[    0.241058]  usbhs_omap: alias fck already exists
[    0.244781] ??????omap_gpio_runtime_resume

diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
index c4ed172..bca3985 100644
--- a/drivers/gpio/gpio-omap.c
+++ b/drivers/gpio/gpio-omap.c
@@ -1146,7 +1146,7 @@ static int __devinit omap_gpio_probe(struct 
platform_device *pdev)

  #if defined(CONFIG_PM_RUNTIME)
  static void omap_gpio_restore_context(struct gpio_bank *bank);
-
+static int flag = 0;
  static int omap_gpio_runtime_suspend(struct device *dev)
  {
         struct platform_device *pdev = to_platform_device(dev);
@@ -1155,6 +1155,8 @@ static int omap_gpio_runtime_suspend(struct device 
*dev)
         unsigned long flags;
         u32 wake_low, wake_hi;

+       flag ++;
+
         spin_lock_irqsave(&bank->lock, flags);

         /*
@@ -1221,6 +1223,11 @@ static int omap_gpio_runtime_resume(struct device 
*dev)
         u32 l = 0, gen, gen0, gen1;
         unsigned long flags;

+       if (flag)
+               flag--;
+       else
+               return 0;
+
         spin_lock_irqsave(&bank->lock, flags);
         _gpio_dbck_enable(bank);

Regards,
Franky