Re: [PATCH 09/13] dt-bindings: phy: Add documentation for Airoha AN7581 USB PHY

[Krzysztof Kozlowski <krzk@kernel.org>]

On 09/03/2025 14:29, Christian Marangi wrote:
> Add documentation for Airoha AN7581 USB PHY that describe the USB PHY
> for the USB controller.
> 
> Airoha AN7581 SoC support a maximum of 2 USB port. The USB 2.0 mode is
> always supported. The USB 3.0 mode is optional and depends on the Serdes
> mode currently configured on the system for the USB port. If USB 3.0 node
> is defined, then airoha,scu-ssr property is required for Serdes mode
> validation.
> 
> Signed-off-by: Christian Marangi <ansuelsmth@gmail.com>
> ---
>  .../bindings/phy/airoha,an7581-usb-phy.yaml   | 106 ++++++++++++++++++
>  MAINTAINERS                                   |   6 +
>  2 files changed, 112 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/phy/airoha,an7581-usb-phy.yaml
> 
> diff --git a/Documentation/devicetree/bindings/phy/airoha,an7581-usb-phy.yaml b/Documentation/devicetree/bindings/phy/airoha,an7581-usb-phy.yaml
> new file mode 100644
> index 000000000000..39127cfb63a7
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/phy/airoha,an7581-usb-phy.yaml
> @@ -0,0 +1,106 @@
> +# SPDX-License-Identifier: GPL-2.0-only OR BSD-2-Clause
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/phy/airoha,an7581-usb-phy.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Airoha AN7581 SoC USB PHY
> +
> +maintainers:
> +  - Christian Marangi <ansuelsmth@gmail.com>
> +
> +description: >
> +  The Airoha AN7581 SoC USB PHY describes the USB PHY for the USB controller.
> +
> +  Airoha AN7581 SoC support a maximum of 2 USB port. The USB 2.0 mode is
> +  always supported. The USB 3.0 mode is optional and depends on the Serdes
> +  mode currently configured on the system for the USB port. If USB 3.0 node
> +  is defined, then airoha,scu-ssr property is required for Serdes mode
> +  validation.
> +
> +properties:
> +  compatible:
> +    const: airoha,an7581-usb-phy
> +
> +  reg:
> +    maxItems: 1
> +
> +  airoha,port-id:
> +    description: Describe the physical port this USB PHY refer to. A dedicated
> +      osciallator is used for each port for the USB 2.0 Slew Rate calibration.

typo

> +    $ref: /schemas/types.yaml#/definitions/uint32
> +    enum: [0, 1]

I don't understand why do you need index property here (which are
usually not allowed).

> +
> +  airoha,scu-ssr:
> +    description: Phandle to the SCU SSR node for USB 3.0 Serdes mode validation.
> +    $ref: /schemas/types.yaml#/definitions/phandle
> +
> +  usb2-phy:
> +    type: object
> +
> +    properties:
> +      '#phy-cells':
> +        const: 1
> +
> +    required:
> +      - '#phy-cells'
> +
> +    additionalProperties: false

Also no resources in usb[23]-phy, so this goes to the parent level and
you have phy-cells=2. Your DTS gives some hint that devices actually
differ but the commit msg contradicts it, so I don't get. Do you have
same IP block here or two different?

> +
> diff --git a/MAINTAINERS b/MAINTAINERS
> index fe34c80b8d52..c2dd385e9165 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -753,6 +753,12 @@ S:	Maintained
>  F:	Documentation/devicetree/bindings/spi/airoha,en7581-snand.yaml
>  F:	drivers/spi/spi-airoha-snfi.c
>  
> +AIROHA USB PHY DRIVER
> +M:	Christian Marangi <ansuelsmth@gmail.com>
> +L:	linux-arm-kernel@lists.infradead.org (moderated for non-subscribers)
> +S:	Maintained
> +F:	Documentation/devicetree/bindings/phy/airoha,an7581-usb-phy.yam

Typo in extension/missing l.



Best regards,
Krzysztof