[PATCH v5 6/7] ARM: mtd: nand: davinci: add OF support for davinci nand controller

[nsekhar@ti.com (Sekhar Nori)]

Hi Heiko,

On 5/30/2012 3:49 PM, Heiko Schocher wrote:
> add OF support for the davinci nand controller.
> 
> Signed-off-by: Heiko Schocher <hs@denx.de>
> Cc: davinci-linux-open-source at linux.davincidsp.com
> Cc: linux-arm-kernel at lists.infradead.org
> Cc: devicetree-discuss at lists.ozlabs.org
> Cc: linux-mtd at lists.infradead.org
> Cc: David Woodhouse <dwmw2@infradead.org>
> Cc: Grant Likely <grant.likely@secretlab.ca>
> Cc: Sekhar Nori <nsekhar@ti.com>
> Cc: Wolfgang Denk <wd@denx.de>
> Cc: Scott Wood <scottwood@freescale.com>
> 
> ---
> - changes for v2:
>   - add comments from Scott Wood:
>     - add "ti,davinci-" prefix
>     - Dashes are preferred to underscores
>     - rename "nandflash" to "nand"
>     - introduce new "ti,davinci" specific properties for setting
>       up ecc_mode, ecc_bits, options and bbt options, instead
>       using linux defines
>     - readme fixes
> - no changes for v3
> - changes for v4
>   remove "pinmux-handle" property as discussed here:
>   http://www.spinics.net/lists/arm-kernel/msg175701.html
>   with Nori Sekhar
> - no changes for v5
> 
>  .../devicetree/bindings/arm/davinci/nand.txt       |   72 ++++++++++++++++++
>  drivers/mtd/nand/davinci_nand.c                    |   80 +++++++++++++++++++-
>  2 files changed, 151 insertions(+), 1 deletions(-)
>  create mode 100644 Documentation/devicetree/bindings/arm/davinci/nand.txt
> 
> diff --git a/Documentation/devicetree/bindings/arm/davinci/nand.txt b/Documentation/devicetree/bindings/arm/davinci/nand.txt
> new file mode 100644
> index 0000000..5afe4a6
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/arm/davinci/nand.txt
> @@ -0,0 +1,72 @@
> +* Texas Instruments Davinci NAND
> +
> +This file provides information, what the device node for the
> +davinci nand interface contain.
> +
> +Required properties:
> +- compatible: "ti,davinci-nand";
> +- reg : contain 2 offset/length values:
> +        - offset and length for the access window
> +        - offset and length for accessing the aemif control registers
> +- ti,davinci-chipselect: Indicates on the davinci_nand driver which
> +                         chipselect is used for accessing the nand.
> +
> +Recommended properties :
> +- ti,davinci-mask-ale: mask for ale
> +- ti,davinci-mask-cle: mask for cle
> +- ti,davinci-mask-chipsel: mask for chipselect
> +- ti,davinci-ecc-mode: ECC mode valid values for davinci driver:
> +		- "none"
> +		- "soft"
> +		- "hw"
> +- ti,davinci-ecc-bits: used ECC bits, currently supported 1 or 4.
> +- ti,davinci-nand-buswidth: buswidth 8 or 16
> +- ti,davinci-nand-use-bbt: use flash based bad block table support.
> +
> +Optional properties:
> +- timing-handle: contains a handle to setup aemif timing.
> +
> +Example (enbw_cmc board):
> +aemif at 60000000 {
> +	compatible = "ti,davinci-aemif";
> +	#address-cells = <2>;
> +	#size-cells = <1>;
> +	reg = <0x68000000 0x80000>;
> +	ranges = <2 0 0x60000000 0x02000000
> +		  3 0 0x62000000 0x02000000
> +		  4 0 0x64000000 0x02000000
> +		  5 0 0x66000000 0x02000000
> +		  6 0 0x68000000 0x02000000>;
> +	nand_cs: cs3 at 68000000 {
> +		compatible = "ti,davinci-cs";
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		/* all timings in nanoseconds */
> +		cs = <3>;
> +		asize = <0>;
> +		ta = <0>;
> +		rhold = <7>;
> +		rstrobe = <42>;
> +		rsetup = <7>;
> +		whold = <7>;
> +		wstrobe = <14>;
> +		wsetup = <7>;
> +		ew = <0>;
> +		ss = <0>;
> +	};
> +	nand at 3,0 {
> +		compatible = "ti,davinci-nand";
> +		reg = <3 0x0 0x807ff
> +			6 0x0 0x8000>;
> +		#address-cells = <1>;
> +		#size-cells = <1>;
> +		ti,davinci-chipselect = <1>;
> +		ti,davinci-mask-ale = <0>;
> +		ti,davinci-mask-cle = <0>;
> +		ti,davinci-mask-chipsel = <0>;
> +		ti,davinci-ecc-mode = "hw";
> +		ti,davinci-ecc-bits = <4>;
> +		ti,davinci-nand-use-bbt;
> +		timing-handle = <&nand_cs>;
> +	};
> +};
> diff --git a/drivers/mtd/nand/davinci_nand.c b/drivers/mtd/nand/davinci_nand.c
> index d94b03c..67bdd29 100644
> --- a/drivers/mtd/nand/davinci_nand.c
> +++ b/drivers/mtd/nand/davinci_nand.c
> @@ -33,9 +33,12 @@
>  #include <linux/mtd/nand.h>
>  #include <linux/mtd/partitions.h>
>  #include <linux/slab.h>
> +#include <linux/of_i2c.h>

This include is not required.

> +#include <linux/of_device.h>
>  
>  #include <mach/nand.h>
>  #include <mach/aemif.h>
> +#include <mach/mux.h>

This too.

>  
>  /*
>   * This is a device driver for the NAND flash controller found on the
> @@ -518,9 +521,81 @@ static struct nand_ecclayout hwecc4_2048 __initconst = {
>  	},
>  };
>  
> +#if defined(CONFIG_OF)
> +static const struct of_device_id davinci_nand_of_match[] = {
> +	{.compatible = "ti,davinci-nand", },
> +	{},
> +}
> +MODULE_DEVICE_TABLE(of, davinci_nand_of_match);
> +
> +static struct davinci_nand_pdata
> +	*nand_davinci_get_pdata(struct platform_device *pdev)
> +{
> +	if ((pdev->dev.platform_data == NULL) &&
> +		(pdev->dev.of_node)) {

You can simplify this and also avoid breaking the statement.

	if (!pdev->dev.platform_data && pdev->dev.of_node) {


> +		struct device_node *tmp_np;
> +		struct davinci_nand_pdata *pdata;
> +		const char *mode;
> +		u32 prop;
> +		int len;
> +
> +		pdata =  kzalloc(sizeof(struct davinci_nand_pdata),
> +				GFP_KERNEL);

I don't see this getting freed anywhere. You wanted to use devm_kzalloc()?

> +		pdev->dev.platform_data = pdata;
> +		if (!pdata)
> +			return NULL;
> +		if (!of_property_read_u32(pdev->dev.of_node,
> +			"ti,davinci-chipselect", &prop))
> +			pdev->id = prop;
> +		if (!of_property_read_u32(pdev->dev.of_node,
> +			"ti,davinci-mask-ale", &prop))
> +			pdata->mask_ale = prop;
> +		if (!of_property_read_u32(pdev->dev.of_node,
> +			"ti,davinci-mask-cle", &prop))
> +			pdata->mask_cle = prop;
> +		if (!of_property_read_u32(pdev->dev.of_node,
> +			"ti,davinci-mask-chipsel", &prop))
> +			pdata->mask_chipsel = prop;
> +		if (!of_property_read_string(pdev->dev.of_node,
> +			"ti,davinci-ecc-mode", &mode)) {
> +			if (!strncmp("none", mode, 4))
> +				pdata->ecc_mode = NAND_ECC_NONE;
> +			if (!strncmp("soft", mode, 4))
> +				pdata->ecc_mode = NAND_ECC_SOFT;
> +			if (!strncmp("hw", mode, 2))
> +				pdata->ecc_mode = NAND_ECC_HW;
> +		}
> +		if (!of_property_read_u32(pdev->dev.of_node,
> +			"ti,davinci-ecc-bits", &prop))
> +			pdata->ecc_bits = prop;
> +		if (!of_property_read_u32(pdev->dev.of_node,
> +			"ti,davinci-nand-buswidth", &prop))
> +			if (prop == 16)
> +				pdata->options |= NAND_BUSWIDTH_16;
> +		if (of_find_property(pdev->dev.of_node,
> +			"ti,davinci-nand-use-bbt", &len))
> +			pdata->bbt_options = NAND_BBT_USE_FLASH;
> +

> +		tmp_np = of_parse_phandle(pdev->dev.of_node,
> +				"timing-handle", 0);
> +		if (tmp_np)
> +			davinci_aemif_setup_timing_of(tmp_np);

Since the aemif driver conversion to DT needs to be looked at along with
its movement to drivers/ folder, is it possible to drop the AEMIF timing
specific bindings from the patch and only keep the NAND specific ones?

Thanks,
Sekhar