* Which kirkwood does your DT board use?
2012-10-20 11:38 Which kirkwood does your DT board use? Andrew Lunn
@ 2012-10-20 12:11 ` Jamie Lentin
2012-10-22 5:10 ` Andrew Lunn
2012-10-20 16:34 ` Alexander Holler
` (5 subsequent siblings)
6 siblings, 1 reply; 10+ messages in thread
From: Jamie Lentin @ 2012-10-20 12:11 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, 20 Oct 2012, Andrew Lunn wrote:
> Hi Folks
>
> All of you in the To: have contributed a DT based Kirkwood board port.
> Nearly all the DT files we have declare the CPU to be
> marvell,kirkwood-88f6281. For adding DT based pinctrl, to replace the
> mpp code, we need to know the exact kirkwood being used. It should be
> one of MV88F6180, MV88F6190, MV88F6192, MV88F6281 or MV88F6282.
>
> You can see what your hardware has a boot time:
>
> Kirkwood: MV88F6282-Rev-A0, TCLK=200000000.
DNS-320:-
Kirkwood: MV88F6281-A1, TCLK=166666667
DNS-325:-
Kirkwood: MV88F6281-A1, TCLK=200000000
"compatible" currently says "marvell,kirkwood-88f6281" for both. Is this
the right string to use or should it be 88f6281-a1?
> Please could you check your hardware and let me know what the correct
> CPU is. I can then fix the .dts files and prepare a first attempt at
> converting boards to pinctrl.
Let me know if I can be useful.
> Thanks
> Andrew
>
--
Jamie Lentin
^ permalink raw reply [flat|nested] 10+ messages in thread
* Which kirkwood does your DT board use?
2012-10-20 11:38 Which kirkwood does your DT board use? Andrew Lunn
2012-10-20 12:11 ` Jamie Lentin
@ 2012-10-20 16:34 ` Alexander Holler
2012-10-20 18:47 ` Simon Baatz
` (4 subsequent siblings)
6 siblings, 0 replies; 10+ messages in thread
From: Alexander Holler @ 2012-10-20 16:34 UTC (permalink / raw)
To: linux-arm-kernel
Am 20.10.2012 13:38, schrieb Andrew Lunn:
> Hi Folks
>
> All of you in the To: have contributed a DT based Kirkwood board port.
> Nearly all the DT files we have declare the CPU to be
> marvell,kirkwood-88f6281. For adding DT based pinctrl, to replace the
> mpp code, we need to know the exact kirkwood being used. It should be
> one of MV88F6180, MV88F6190, MV88F6192, MV88F6281 or MV88F6282.
>
> You can see what your hardware has a boot time:
>
> Kirkwood: MV88F6282-Rev-A0, TCLK=200000000.
>
> Please could you check your hardware and let me know what the correct
> CPU is. I can then fix the .dts files and prepare a first attempt at
> converting boards to pinctrl.
The Dockstars are using this one:
Kirkwood: MV88F6281-A0, TCLK=200000000.
Regards,
Alexander
^ permalink raw reply [flat|nested] 10+ messages in thread
* Which kirkwood does your DT board use?
2012-10-20 11:38 Which kirkwood does your DT board use? Andrew Lunn
2012-10-20 12:11 ` Jamie Lentin
2012-10-20 16:34 ` Alexander Holler
@ 2012-10-20 18:47 ` Simon Baatz
2012-10-20 20:28 ` Michael Walle
` (3 subsequent siblings)
6 siblings, 0 replies; 10+ messages in thread
From: Simon Baatz @ 2012-10-20 18:47 UTC (permalink / raw)
To: linux-arm-kernel
Hi Andrew,
On Sat, Oct 20, 2012 at 01:38:00PM +0200, Andrew Lunn wrote:
> Hi Folks
>
> All of you in the To: have contributed a DT based Kirkwood board port.
> Nearly all the DT files we have declare the CPU to be
> marvell,kirkwood-88f6281. For adding DT based pinctrl, to replace the
> mpp code, we need to know the exact kirkwood being used. It should be
> one of MV88F6180, MV88F6190, MV88F6192, MV88F6281 or MV88F6282.
>
> You can see what your hardware has a boot time:
>
> Kirkwood: MV88F6282-Rev-A0, TCLK=200000000.
>
> Please could you check your hardware and let me know what the correct
> CPU is. I can then fix the .dts files and prepare a first attempt at
> converting boards to pinctrl.
>
My IB-NAS6210 says:
Kirkwood: MV88F6281-A1, TCLK=200000000.
I don't have a 6220, but I suppose it is the same since they seem to
use the same board internally.
- Simon
^ permalink raw reply [flat|nested] 10+ messages in thread
* Which kirkwood does your DT board use?
2012-10-20 11:38 Which kirkwood does your DT board use? Andrew Lunn
` (2 preceding siblings ...)
2012-10-20 18:47 ` Simon Baatz
@ 2012-10-20 20:28 ` Michael Walle
2012-10-21 0:08 ` Josh Coombs
` (2 subsequent siblings)
6 siblings, 0 replies; 10+ messages in thread
From: Michael Walle @ 2012-10-20 20:28 UTC (permalink / raw)
To: linux-arm-kernel
Am Samstag 20 Oktober 2012, 13:38:00 schrieb Andrew Lunn:
> Hi Folks
>
> All of you in the To: have contributed a DT based Kirkwood board port.
> Nearly all the DT files we have declare the CPU to be
> marvell,kirkwood-88f6281. For adding DT based pinctrl, to replace the
> mpp code, we need to know the exact kirkwood being used. It should be
> one of MV88F6180, MV88F6190, MV88F6192, MV88F6281 or MV88F6282.
>
> You can see what your hardware has a boot time:
>
> Kirkwood: MV88F6282-Rev-A0, TCLK=200000000.
>
> Please could you check your hardware and let me know what the correct
> CPU is. I can then fix the .dts files and prepare a first attempt at
> converting boards to pinctrl.
>
> Thanks
> Andrew
LS-XHL:
Kirkwood: MV88F6281-A0, TCLK=200000000
LS-CHLv2:
Kirkwood: MV88F6281-A1, TCLK=166666667
--
Michael
^ permalink raw reply [flat|nested] 10+ messages in thread
* Which kirkwood does your DT board use?
2012-10-20 11:38 Which kirkwood does your DT board use? Andrew Lunn
` (3 preceding siblings ...)
2012-10-20 20:28 ` Michael Walle
@ 2012-10-21 0:08 ` Josh Coombs
2012-10-22 13:36 ` Jason Cooper
2012-10-22 21:27 ` Adam Baker
6 siblings, 0 replies; 10+ messages in thread
From: Josh Coombs @ 2012-10-21 0:08 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, Oct 20, 2012 at 7:38 AM, Andrew Lunn <andrew@lunn.ch> wrote:
> Hi Folks
>
> All of you in the To: have contributed a DT based Kirkwood board port.
> Nearly all the DT files we have declare the CPU to be
> marvell,kirkwood-88f6281. For adding DT based pinctrl, to replace the
> mpp code, we need to know the exact kirkwood being used. It should be
> one of MV88F6180, MV88F6190, MV88F6192, MV88F6281 or MV88F6282.
>
> You can see what your hardware has a boot time:
>
> Kirkwood: MV88F6282-Rev-A0, TCLK=200000000.
>
> Please could you check your hardware and let me know what the correct
> CPU is. I can then fix the .dts files and prepare a first attempt at
> converting boards to pinctrl.
>
> Thanks
> Andrew
Seagate GoFlexNet
[jcoombs at alarm ~]$ dmesg | grep -i tclk
[ 5.851008] Kirkwood: MV88F6281-A0, TCLK=200000000.
Joshua Coombs
^ permalink raw reply [flat|nested] 10+ messages in thread
* Which kirkwood does your DT board use?
2012-10-20 11:38 Which kirkwood does your DT board use? Andrew Lunn
` (4 preceding siblings ...)
2012-10-21 0:08 ` Josh Coombs
@ 2012-10-22 13:36 ` Jason Cooper
2012-10-22 21:27 ` Adam Baker
6 siblings, 0 replies; 10+ messages in thread
From: Jason Cooper @ 2012-10-22 13:36 UTC (permalink / raw)
To: linux-arm-kernel
On Sat, Oct 20, 2012 at 01:38:00PM +0200, Andrew Lunn wrote:
> Hi Folks
>
> All of you in the To: have contributed a DT based Kirkwood board port.
> Nearly all the DT files we have declare the CPU to be
> marvell,kirkwood-88f6281. For adding DT based pinctrl, to replace the
> mpp code, we need to know the exact kirkwood being used. It should be
> one of MV88F6180, MV88F6190, MV88F6192, MV88F6281 or MV88F6282.
>
> You can see what your hardware has a boot time:
>
> Kirkwood: MV88F6282-Rev-A0, TCLK=200000000.
>
> Please could you check your hardware and let me know what the correct
> CPU is. I can then fix the .dts files and prepare a first attempt at
> converting boards to pinctrl.
Dreamplug:
Kirkwood: MV88F6281-A1, TCLK=200000000.
hth,
Jason.
^ permalink raw reply [flat|nested] 10+ messages in thread
* Which kirkwood does your DT board use?
2012-10-20 11:38 Which kirkwood does your DT board use? Andrew Lunn
` (5 preceding siblings ...)
2012-10-22 13:36 ` Jason Cooper
@ 2012-10-22 21:27 ` Adam Baker
2012-10-23 18:37 ` Andrew Lunn
6 siblings, 1 reply; 10+ messages in thread
From: Adam Baker @ 2012-10-22 21:27 UTC (permalink / raw)
To: linux-arm-kernel
On 20/10/12 12:38, Andrew Lunn wrote:
> Hi Folks
>
> All of you in the To: have contributed a DT based Kirkwood board port.
> Nearly all the DT files we have declare the CPU to be
> marvell,kirkwood-88f6281. For adding DT based pinctrl, to replace the
> mpp code, we need to know the exact kirkwood being used. It should be
> one of MV88F6180, MV88F6190, MV88F6192, MV88F6281 or MV88F6282.
>
> You can see what your hardware has a boot time:
>
> Kirkwood: MV88F6282-Rev-A0, TCLK=200000000.
>
> Please could you check your hardware and let me know what the correct
> CPU is. I can then fix the .dts files and prepare a first attempt at
> converting boards to pinctrl.
>
Hi,
I've not seen a reply from Arnaud yet so I'll offer
Iomega Iconnect
Kirkwood: MV88F6281-A0, TCLK=200000000.
Regards
Adam
^ permalink raw reply [flat|nested] 10+ messages in thread
* Which kirkwood does your DT board use?
2012-10-22 21:27 ` Adam Baker
@ 2012-10-23 18:37 ` Andrew Lunn
0 siblings, 0 replies; 10+ messages in thread
From: Andrew Lunn @ 2012-10-23 18:37 UTC (permalink / raw)
To: linux-arm-kernel
On Mon, Oct 22, 2012 at 10:27:48PM +0100, Adam Baker wrote:
> On 20/10/12 12:38, Andrew Lunn wrote:
> >Hi Folks
> >
> >All of you in the To: have contributed a DT based Kirkwood board port.
> >Nearly all the DT files we have declare the CPU to be
> >marvell,kirkwood-88f6281. For adding DT based pinctrl, to replace the
> >mpp code, we need to know the exact kirkwood being used. It should be
> >one of MV88F6180, MV88F6190, MV88F6192, MV88F6281 or MV88F6282.
> >
> >You can see what your hardware has a boot time:
> >
> >Kirkwood: MV88F6282-Rev-A0, TCLK=200000000.
> >
> >Please could you check your hardware and let me know what the correct
> >CPU is. I can then fix the .dts files and prepare a first attempt at
> >converting boards to pinctrl.
> >
>
> Hi,
>
> I've not seen a reply from Arnaud yet so I'll offer
>
> Iomega Iconnect
> Kirkwood: MV88F6281-A0, TCLK=200000000.
Hi Adam
Thanks. Arnaud replied p-t-p.
I'm was missing just one reply, but with a bit of googling, i found a
boot log online, so could fill the gap.
kirkwood-dns320.dts MV88F6281
kirkwood-dns325.dts MV88F6281
kirkwood-dockstar.dts MV88F6281
kirkwood-dreamplug.dts MV88F6281
kirkwood-goflexnet.dts MV88F6281
kirkwood-ib62x0.dts MV88F6281
kirkwood-iconnect.dts MV88F6281
kirkwood-iomega_ix2_200.dts MV88F6281
kirkwood-lschlv2.dts MV88F6281
kirkwood-lsxhl.dts MV88F6281
kirkwood-ts219-6281.dts MV88F6281
kirkwood-ts219-6282.dts MV88F6282
Not what i was expecting, nearly every one being 6281!
But it does mean there are no DT files to correct :-)
Thanks for your answers everybody.
Andrew
^ permalink raw reply [flat|nested] 10+ messages in thread