From: m-karicheri2@ti.com (Murali Karicheri)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v3 04/11] clk: davinci - add pll divider clock driver
Date: Wed, 31 Oct 2012 09:22:04 -0400 [thread overview]
Message-ID: <509125FC.1090609@ti.com> (raw)
In-Reply-To: <CACRpkdY3ji_twCqej6Yf8grR7oovf3jeGrbQMzybk5CK5f2Y9A@mail.gmail.com>
On 10/28/2012 03:26 PM, Linus Walleij wrote:
> On Thu, Oct 25, 2012 at 6:11 PM, Murali Karicheri <m-karicheri2@ti.com> wrote:
>
>> pll dividers are present in the pll controller of DaVinci and Other
>> SoCs that re-uses the same hardware IP. This has a enable bit for
>> bypass the divider or enable the driver. This is a sub class of the
>> clk-divider clock checks the enable bit to calculare the rate and
>> invoke the recalculate() function of the clk-divider if enabled.
>>
>> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
> Looking good,
> Acked-by: Linus Walleij <linus.walleij@linaro.org>
>
> Yours,
> Linus Walleij
>
Linus,
Thanks. I will add your Acked-by in the next version.
Murali
next prev parent reply other threads:[~2012-10-31 13:22 UTC|newest]
Thread overview: 60+ messages / expand[flat|nested] mbox.gz Atom feed top
2012-10-25 16:11 [PATCH v3 00/11] common clk drivers migration for DaVinci SoCs Murali Karicheri
2012-10-25 16:11 ` [PATCH v3 01/11] clk: davinci - add main PLL clock driver Murali Karicheri
2012-10-28 19:18 ` Linus Walleij
2012-10-31 13:23 ` Murali Karicheri
2012-10-31 12:29 ` Sekhar Nori
2012-10-31 13:46 ` Murali Karicheri
2012-11-01 11:01 ` Sekhar Nori
2012-10-25 16:11 ` [PATCH v3 02/11] clk: davinci - add PSC " Murali Karicheri
2012-10-28 19:24 ` Linus Walleij
2012-10-31 13:23 ` Murali Karicheri
2013-03-19 10:57 ` Sekhar Nori
2012-11-03 12:07 ` Sekhar Nori
2012-11-05 15:10 ` Murali Karicheri
2012-11-10 2:22 ` Mike Turquette
2012-11-27 15:05 ` Sekhar Nori
2012-11-27 17:29 ` Mike Turquette
2012-11-27 20:38 ` Murali Karicheri
2012-11-28 13:22 ` Sekhar Nori
2013-03-22 11:20 ` Sekhar Nori
2013-03-22 20:37 ` Mike Turquette
2013-03-25 6:50 ` Sekhar Nori
2012-10-25 16:11 ` [PATCH v3 03/11] clk: davinci - common clk utilities to init clk driver Murali Karicheri
2012-10-28 19:25 ` Linus Walleij
2012-10-31 13:23 ` Murali Karicheri
2012-11-01 12:41 ` Sekhar Nori
2012-11-01 18:34 ` Murali Karicheri
2012-11-03 12:35 ` Sekhar Nori
2012-11-05 15:20 ` Murali Karicheri
2012-11-06 9:31 ` Sekhar Nori
2012-11-06 15:04 ` Murali Karicheri
2012-10-25 16:11 ` [PATCH v3 04/11] clk: davinci - add pll divider clock driver Murali Karicheri
2012-10-28 19:26 ` Linus Walleij
2012-10-31 13:22 ` Murali Karicheri [this message]
2012-11-02 11:33 ` Sekhar Nori
2012-11-02 13:53 ` Murali Karicheri
2012-11-03 12:03 ` Sekhar Nori
2012-11-05 15:10 ` Murali Karicheri
2012-10-25 16:11 ` [PATCH v3 05/11] clk: davinci - add dm644x clock initialization Murali Karicheri
2012-11-03 13:30 ` Sekhar Nori
2012-11-05 15:42 ` Murali Karicheri
2012-11-06 10:18 ` Sekhar Nori
2012-11-05 23:23 ` Murali Karicheri
2012-11-06 9:40 ` Sekhar Nori
2012-10-25 16:11 ` [PATCH v3 06/11] clk: davinci - add build infrastructure for DaVinci clock drivers Murali Karicheri
2012-11-04 13:34 ` Sekhar Nori
2012-11-05 16:17 ` Murali Karicheri
2012-11-06 9:48 ` Sekhar Nori
2012-10-25 16:11 ` [PATCH v3 07/11] ARM: davinci - restructure header files for common clock migration Murali Karicheri
2012-11-04 14:05 ` Sekhar Nori
2012-11-05 19:11 ` Murali Karicheri
2012-11-06 10:03 ` Sekhar Nori
2012-11-05 21:57 ` Murali Karicheri
2012-12-03 13:23 ` Sekhar Nori
2012-10-25 16:11 ` [PATCH v3 08/11] ARM: davinci - migrating to use common clock init code Murali Karicheri
2012-10-25 16:11 ` [PATCH v3 09/11] ARM: davinci - dm644x: update SoC code to remove the clock data Murali Karicheri
2012-10-25 16:11 ` [PATCH v3 10/11] ARM: davinci - migrate to common clock Murali Karicheri
2012-11-04 13:06 ` Sekhar Nori
2012-11-05 15:43 ` Murali Karicheri
2012-10-25 16:11 ` [PATCH v3 11/11] ARM: davinci - common clock migration: clean up the old code Murali Karicheri
2012-10-30 17:00 ` [PATCH v3 00/11] common clk drivers migration for DaVinci SoCs Karicheri, Muralidharan
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=509125FC.1090609@ti.com \
--to=m-karicheri2@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).