Re: [PATCH] ARM: dts: add device tree for Mecer Xtreme Mini S6

Heiko Stuebner
2019-07-25T22:19:48Z

Hi Justin,

Am Sonntag, 16. Juni 2019, 22:47:45 CEST schrieb Justin Swartz:
> The Mecer Xtreme Mini S6 features a Rockchip RK3229 SoC,
> 1GB DDR3 RAM, 8GB eMMC, MicroSD port, 10/100Mbps Ethernet,
> Realtek 8723BS WLAN module, 2 x USB 2.0 ports, HDMI output,
> and S/PDIF output.
>
> Signed-off-by: Justin Swartz <justin.swartz@risingedge.co.za>
> ---

please add an entry to Documentation/devicetree/bindings/arm/rockchip.yaml
for your board and if necessary also a vendor-prefix to
Documentation/devicetree/bindings/vendor-prefixes.(yaml?)

See below.

> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/rk3229-xms6.dts | 286 ++++++++++++++++++++++++++++++++++++++
> 2 files changed, 287 insertions(+)
> create mode 100644 arch/arm/boot/dts/rk3229-xms6.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index dab2914fa293..6fbd7c304f62 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -902,6 +902,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += \
> rk3188-radxarock.dtb \
> rk3228-evb.dtb \
> rk3229-evb.dtb \
> + rk3229-xms6.dtb \
> rk3288-evb-act8846.dtb \
> rk3288-evb-rk808.dtb \
> rk3288-fennec.dtb \
> diff --git a/arch/arm/boot/dts/rk3229-xms6.dts b/arch/arm/boot/dts/rk3229-xms6.dts
> new file mode 100644
> index 000000000000..9b666fa66292
> --- /dev/null
> +++ b/arch/arm/boot/dts/rk3229-xms6.dts
> @@ -0,0 +1,286 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +
> +/dts-v1/;
> +
> +#include <dt-bindings/input/input.h>
> +#include "rk3229.dtsi"
> +
> +/ {
> + model = "Rockchip RK3229 (Mecer Xtreme Mini S6)";
> + compatible = "rockchip,rk3229-xms6", "rockchip,rk3229";

mode = "Mecer Xtreme Mini S6";
compatible = "mecer,xms6", "rockchip,rk3229";

(and as written above, add a vendor-prefix for mecer)

...

> +&cpu0 {
> + clock-frequency = <1464000000>;

not sure I understand the reasoning here.
There seems to be a regulator defined, so the cpu cores should
have operating points defined to allow them to switch between
different frequencies as needed.

> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu1 {
> + clock-frequency = <1464000000>;
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu2 {
> + clock-frequency = <1464000000>;
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&cpu3 {
> + clock-frequency = <1464000000>;
> + cpu-supply = <&vdd_arm>;
> +};
> +
> +&vop {

please sort the &node-references alphabetically.

Heiko