[PATCH] Revert "serial: omap: fix software flow control"

[andreas.devel@googlemail.com (Andreas Bießmann)]

On 16.10.2012 16:09, Felipe Balbi wrote:
> This reverts commit 957ee7270d632245b43f6feb0e70d9a5e9ea6cf6
> (serial: omap: fix software flow control).
> 
> As Russell has pointed out, that commit isn't fixing
> Software Flow Control at all, and it actually makes
> it even more broken.
> 
> It was agreed to revert this commit and use Russell's
> latest UART patches instead.
> 
> Cc: Russell King <linux@arm.linux.org.uk>
> Signed-off-by: Felipe Balbi <balbi@ti.com>

since 957ee7270d632245b43f6feb0e70d9a5e9ea6cf6 made it into stable (at
least 3.4) I think it would be good decision to also apply this revert
to stable until a working solution exists.

Best regards

Andreas Bie?mann

> ---
> 
> Hi Greg,
> 
> you might prefer to do the revert yourself, in that case just
> revert commit 957ee7270d632245b43f6feb0e70d9a5e9ea6cf6.
> 
> thanks
> 
>  arch/arm/plat-omap/include/plat/omap-serial.h |  4 ++--
>  drivers/tty/serial/omap-serial.c              | 12 ++++++------
>  2 files changed, 8 insertions(+), 8 deletions(-)
> 
> diff --git a/arch/arm/plat-omap/include/plat/omap-serial.h b/arch/arm/plat-omap/include/plat/omap-serial.h
> index f4a4cd0..1957a85 100644
> --- a/arch/arm/plat-omap/include/plat/omap-serial.h
> +++ b/arch/arm/plat-omap/include/plat/omap-serial.h
> @@ -40,10 +40,10 @@
>  #define OMAP_UART_WER_MOD_WKUP	0X7F
>  
>  /* Enable XON/XOFF flow control on output */
> -#define OMAP_UART_SW_TX		0x8
> +#define OMAP_UART_SW_TX		0x04
>  
>  /* Enable XON/XOFF flow control on input */
> -#define OMAP_UART_SW_RX		0x2
> +#define OMAP_UART_SW_RX		0x04
>  
>  #define OMAP_UART_SYSC_RESET	0X07
>  #define OMAP_UART_TCR_TRIG	0X0F
> diff --git a/drivers/tty/serial/omap-serial.c b/drivers/tty/serial/omap-serial.c
> index 6ede6fd..6d3d26a 100644
> --- a/drivers/tty/serial/omap-serial.c
> +++ b/drivers/tty/serial/omap-serial.c
> @@ -671,19 +671,19 @@ serial_omap_configure_xonxoff
>  
>  	/*
>  	 * IXON Flag:
> -	 * Flow control for OMAP.TX
> -	 * OMAP.RX should listen for XON/XOFF
> +	 * Enable XON/XOFF flow control on output.
> +	 * Transmit XON1, XOFF1
>  	 */
>  	if (termios->c_iflag & IXON)
> -		up->efr |= OMAP_UART_SW_RX;
> +		up->efr |= OMAP_UART_SW_TX;
>  
>  	/*
>  	 * IXOFF Flag:
> -	 * Flow control for OMAP.RX
> -	 * OMAP.TX should send XON/XOFF
> +	 * Enable XON/XOFF flow control on input.
> +	 * Receiver compares XON1, XOFF1.
>  	 */
>  	if (termios->c_iflag & IXOFF)
> -		up->efr |= OMAP_UART_SW_TX;
> +		up->efr |= OMAP_UART_SW_RX;
>  
>  	serial_out(up, UART_EFR, up->efr | UART_EFR_ECB);
>  	serial_out(up, UART_LCR, UART_LCR_CONF_MODE_A);
>