* [PATCH 1/1] arm: at91: add Ronetix pm9g45 board support
@ 2012-10-19 2:19 Jean-Christophe PLAGNIOL-VILLARD
2012-11-16 13:08 ` Nicolas Ferre
0 siblings, 1 reply; 4+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-10-19 2:19 UTC (permalink / raw)
To: linux-arm-kernel
CPU Module with ATMEL AT91SAM9G45
http://www.ronetix.at/pm9g45.html
Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/pm9g45.dts | 144 ++++++++++++++++++++++++++++++++++++++++++
2 files changed, 145 insertions(+)
create mode 100644 arch/arm/boot/dts/pm9g45.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index a9b051a..627b6ad 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb
dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb
# sam9g45
dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb
+dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb
# sam9n12
dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb
# sam9x5
diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/pm9g45.dts
new file mode 100644
index 0000000..b0c258d
--- /dev/null
+++ b/arch/arm/boot/dts/pm9g45.dts
@@ -0,0 +1,144 @@
+/*
+ * pm9g45.dts - Device Tree file for Ronetix pm9g45 board
+ *
+ * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
+ *
+ * Licensed under GPLv2.
+ */
+/dts-v1/;
+/include/ "at91sam9g45.dtsi"
+
+/ {
+ model = "Ronetix pm9g45";
+ compatible = "ronetix,pm9g45", "atmel,at91sam9g45", "atmel,at91sam9";
+
+ chosen {
+ bootargs = "console=ttyS0,115200";
+ };
+
+ memory {
+ reg = <0x70000000 0x8000000>;
+ };
+
+ clocks {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ main_clock: clock at 0 {
+ compatible = "atmel,osc", "fixed-clock";
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ dbgu: serial at ffffee00 {
+ status = "okay";
+ };
+
+ pinctrl at fffff200 {
+
+ board {
+ pinctrl_board_nand: nand0-board {
+ atmel,pins =
+ <3 3 0x0 0x1 /* PD3 gpio RDY pin pull_up*/
+ 2 14 0x0 0x1>; /* PC14 gpio enable pin pull_up */
+ };
+ };
+ };
+
+ macb0: ethernet at fffbc000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+ };
+
+ nand0: nand at 40000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "soft";
+ nand-on-flash-bbt;
+ pinctrl-0 = <&pinctrl_board_nand>;
+
+ gpios = <&pioD 3 0
+ &pioC 14 0
+ 0
+ >;
+
+ status = "okay";
+
+ at91bootstrap at 0 {
+ label = "at91bootstrap";
+ reg = <0x0 0x20000>;
+ };
+
+ barebox at 20000 {
+ label = "barebox";
+ reg = <0x20000 0x40000>;
+ };
+
+ bareboxenv at 60000 {
+ label = "bareboxenv";
+ reg = <0x60000 0x1A0000>;
+ };
+
+ kernel at 200000 {
+ label = "bareboxenv2";
+ reg = <0x200000 0x300000>;
+ };
+
+ kernel at 500000 {
+ label = "root";
+ reg = <0x500000 0x400000>;
+ };
+
+ data at 900000 {
+ label = "data";
+ reg = <0x900000 0x8340000>;
+ };
+ };
+
+ usb0: ohci at 00700000 {
+ status = "okay";
+ num-ports = <2>;
+ };
+
+ usb1: ehci at 00800000 {
+ status = "okay";
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+
+ led0 {
+ label = "led0";
+ gpios = <&pioD 0 1>;
+ linux,default-trigger = "nand-disk";
+ };
+
+ led1 {
+ label = "led1";
+ gpios = <&pioD 31 0>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ right {
+ label = "SW4";
+ gpios = <&pioE 7 1>;
+ linux,code = <106>;
+ };
+
+ up {
+ label = "SW3";
+ gpios = <&pioE 8 1>;
+ linux,code = <103>;
+ };
+ };
+};
--
1.7.10.4
^ permalink raw reply related [flat|nested] 4+ messages in thread
* [PATCH 1/1] arm: at91: add Ronetix pm9g45 board support
2012-10-19 2:19 [PATCH 1/1] arm: at91: add Ronetix pm9g45 board support Jean-Christophe PLAGNIOL-VILLARD
@ 2012-11-16 13:08 ` Nicolas Ferre
2012-11-16 13:28 ` Jean-Christophe PLAGNIOL-VILLARD
0 siblings, 1 reply; 4+ messages in thread
From: Nicolas Ferre @ 2012-11-16 13:08 UTC (permalink / raw)
To: linux-arm-kernel
On 10/19/2012 04:19 AM, Jean-Christophe PLAGNIOL-VILLARD :
> CPU Module with ATMEL AT91SAM9G45
> http://www.ronetix.at/pm9g45.html
>
> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
Ok, queued in at91-3.8-dt branch.
I had to modify the Makefile part of it to match current move to
arch/arm/boot/dts/Makefile.
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
> ---
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/pm9g45.dts | 144 ++++++++++++++++++++++++++++++++++++++++++
> 2 files changed, 145 insertions(+)
> create mode 100644 arch/arm/boot/dts/pm9g45.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index a9b051a..627b6ad 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb
> dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb
> # sam9g45
> dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb
> +dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb
> # sam9n12
> dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb
> # sam9x5
> diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/pm9g45.dts
> new file mode 100644
> index 0000000..b0c258d
> --- /dev/null
> +++ b/arch/arm/boot/dts/pm9g45.dts
> @@ -0,0 +1,144 @@
> +/*
> + * pm9g45.dts - Device Tree file for Ronetix pm9g45 board
> + *
> + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> + *
> + * Licensed under GPLv2.
> + */
> +/dts-v1/;
> +/include/ "at91sam9g45.dtsi"
> +
> +/ {
> + model = "Ronetix pm9g45";
> + compatible = "ronetix,pm9g45", "atmel,at91sam9g45", "atmel,at91sam9";
> +
> + chosen {
> + bootargs = "console=ttyS0,115200";
> + };
> +
> + memory {
> + reg = <0x70000000 0x8000000>;
> + };
> +
> + clocks {
> + #address-cells = <1>;
> + #size-cells = <1>;
> + ranges;
> +
> + main_clock: clock at 0 {
> + compatible = "atmel,osc", "fixed-clock";
> + clock-frequency = <12000000>;
> + };
> + };
> +
> + ahb {
> + apb {
> + dbgu: serial at ffffee00 {
> + status = "okay";
> + };
> +
> + pinctrl at fffff200 {
> +
> + board {
> + pinctrl_board_nand: nand0-board {
> + atmel,pins =
> + <3 3 0x0 0x1 /* PD3 gpio RDY pin pull_up*/
> + 2 14 0x0 0x1>; /* PC14 gpio enable pin pull_up */
> + };
> + };
> + };
> +
> + macb0: ethernet at fffbc000 {
> + phy-mode = "rmii";
> + status = "okay";
> + };
> + };
> +
> + nand0: nand at 40000000 {
> + nand-bus-width = <8>;
> + nand-ecc-mode = "soft";
> + nand-on-flash-bbt;
> + pinctrl-0 = <&pinctrl_board_nand>;
> +
> + gpios = <&pioD 3 0
> + &pioC 14 0
> + 0
> + >;
> +
> + status = "okay";
> +
> + at91bootstrap at 0 {
> + label = "at91bootstrap";
> + reg = <0x0 0x20000>;
> + };
> +
> + barebox at 20000 {
> + label = "barebox";
> + reg = <0x20000 0x40000>;
> + };
> +
> + bareboxenv at 60000 {
> + label = "bareboxenv";
> + reg = <0x60000 0x1A0000>;
> + };
> +
> + kernel at 200000 {
> + label = "bareboxenv2";
> + reg = <0x200000 0x300000>;
> + };
> +
> + kernel at 500000 {
> + label = "root";
> + reg = <0x500000 0x400000>;
> + };
> +
> + data at 900000 {
> + label = "data";
> + reg = <0x900000 0x8340000>;
> + };
> + };
> +
> + usb0: ohci at 00700000 {
> + status = "okay";
> + num-ports = <2>;
> + };
> +
> + usb1: ehci at 00800000 {
> + status = "okay";
> + };
> + };
> +
> + leds {
> + compatible = "gpio-leds";
> +
> + led0 {
> + label = "led0";
> + gpios = <&pioD 0 1>;
> + linux,default-trigger = "nand-disk";
> + };
> +
> + led1 {
> + label = "led1";
> + gpios = <&pioD 31 0>;
> + linux,default-trigger = "heartbeat";
> + };
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + right {
> + label = "SW4";
> + gpios = <&pioE 7 1>;
> + linux,code = <106>;
> + };
> +
> + up {
> + label = "SW3";
> + gpios = <&pioE 8 1>;
> + linux,code = <103>;
> + };
> + };
> +};
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH 1/1] arm: at91: add Ronetix pm9g45 board support
2012-11-16 13:08 ` Nicolas Ferre
@ 2012-11-16 13:28 ` Jean-Christophe PLAGNIOL-VILLARD
2012-11-16 13:32 ` Nicolas Ferre
0 siblings, 1 reply; 4+ messages in thread
From: Jean-Christophe PLAGNIOL-VILLARD @ 2012-11-16 13:28 UTC (permalink / raw)
To: linux-arm-kernel
On 14:08 Fri 16 Nov , Nicolas Ferre wrote:
> On 10/19/2012 04:19 AM, Jean-Christophe PLAGNIOL-VILLARD :
> > CPU Module with ATMEL AT91SAM9G45
> > http://www.ronetix.at/pm9g45.html
> >
> > Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> > Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>
> Ok, queued in at91-3.8-dt branch.
>
> I had to modify the Makefile part of it to match current move to
> arch/arm/boot/dts/Makefile.
>
> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
I prefer to go via linus W I've other updte for the macb on the top of it
ditto for the rm9200
Best Regards,
J.
>
> > ---
> > arch/arm/boot/dts/Makefile | 1 +
> > arch/arm/boot/dts/pm9g45.dts | 144 ++++++++++++++++++++++++++++++++++++++++++
> > 2 files changed, 145 insertions(+)
> > create mode 100644 arch/arm/boot/dts/pm9g45.dts
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index a9b051a..627b6ad 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb
> > dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb
> > # sam9g45
> > dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb
> > +dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb
> > # sam9n12
> > dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb
> > # sam9x5
> > diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/pm9g45.dts
> > new file mode 100644
> > index 0000000..b0c258d
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/pm9g45.dts
> > @@ -0,0 +1,144 @@
> > +/*
> > + * pm9g45.dts - Device Tree file for Ronetix pm9g45 board
> > + *
> > + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
> > + *
> > + * Licensed under GPLv2.
> > + */
> > +/dts-v1/;
> > +/include/ "at91sam9g45.dtsi"
> > +
> > +/ {
> > + model = "Ronetix pm9g45";
> > + compatible = "ronetix,pm9g45", "atmel,at91sam9g45", "atmel,at91sam9";
> > +
> > + chosen {
> > + bootargs = "console=ttyS0,115200";
> > + };
> > +
> > + memory {
> > + reg = <0x70000000 0x8000000>;
> > + };
> > +
> > + clocks {
> > + #address-cells = <1>;
> > + #size-cells = <1>;
> > + ranges;
> > +
> > + main_clock: clock at 0 {
> > + compatible = "atmel,osc", "fixed-clock";
> > + clock-frequency = <12000000>;
> > + };
> > + };
> > +
> > + ahb {
> > + apb {
> > + dbgu: serial at ffffee00 {
> > + status = "okay";
> > + };
> > +
> > + pinctrl at fffff200 {
> > +
> > + board {
> > + pinctrl_board_nand: nand0-board {
> > + atmel,pins =
> > + <3 3 0x0 0x1 /* PD3 gpio RDY pin pull_up*/
> > + 2 14 0x0 0x1>; /* PC14 gpio enable pin pull_up */
> > + };
> > + };
> > + };
> > +
> > + macb0: ethernet at fffbc000 {
> > + phy-mode = "rmii";
> > + status = "okay";
> > + };
> > + };
> > +
> > + nand0: nand at 40000000 {
> > + nand-bus-width = <8>;
> > + nand-ecc-mode = "soft";
> > + nand-on-flash-bbt;
> > + pinctrl-0 = <&pinctrl_board_nand>;
> > +
> > + gpios = <&pioD 3 0
> > + &pioC 14 0
> > + 0
> > + >;
> > +
> > + status = "okay";
> > +
> > + at91bootstrap at 0 {
> > + label = "at91bootstrap";
> > + reg = <0x0 0x20000>;
> > + };
> > +
> > + barebox at 20000 {
> > + label = "barebox";
> > + reg = <0x20000 0x40000>;
> > + };
> > +
> > + bareboxenv at 60000 {
> > + label = "bareboxenv";
> > + reg = <0x60000 0x1A0000>;
> > + };
> > +
> > + kernel at 200000 {
> > + label = "bareboxenv2";
> > + reg = <0x200000 0x300000>;
> > + };
> > +
> > + kernel at 500000 {
> > + label = "root";
> > + reg = <0x500000 0x400000>;
> > + };
> > +
> > + data at 900000 {
> > + label = "data";
> > + reg = <0x900000 0x8340000>;
> > + };
> > + };
> > +
> > + usb0: ohci at 00700000 {
> > + status = "okay";
> > + num-ports = <2>;
> > + };
> > +
> > + usb1: ehci at 00800000 {
> > + status = "okay";
> > + };
> > + };
> > +
> > + leds {
> > + compatible = "gpio-leds";
> > +
> > + led0 {
> > + label = "led0";
> > + gpios = <&pioD 0 1>;
> > + linux,default-trigger = "nand-disk";
> > + };
> > +
> > + led1 {
> > + label = "led1";
> > + gpios = <&pioD 31 0>;
> > + linux,default-trigger = "heartbeat";
> > + };
> > + };
> > +
> > + gpio_keys {
> > + compatible = "gpio-keys";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + right {
> > + label = "SW4";
> > + gpios = <&pioE 7 1>;
> > + linux,code = <106>;
> > + };
> > +
> > + up {
> > + label = "SW3";
> > + gpios = <&pioE 8 1>;
> > + linux,code = <103>;
> > + };
> > + };
> > +};
> >
>
>
> --
> Nicolas Ferre
^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH 1/1] arm: at91: add Ronetix pm9g45 board support
2012-11-16 13:28 ` Jean-Christophe PLAGNIOL-VILLARD
@ 2012-11-16 13:32 ` Nicolas Ferre
0 siblings, 0 replies; 4+ messages in thread
From: Nicolas Ferre @ 2012-11-16 13:32 UTC (permalink / raw)
To: linux-arm-kernel
On 11/16/2012 02:28 PM, Jean-Christophe PLAGNIOL-VILLARD :
> On 14:08 Fri 16 Nov , Nicolas Ferre wrote:
>> On 10/19/2012 04:19 AM, Jean-Christophe PLAGNIOL-VILLARD :
>>> CPU Module with ATMEL AT91SAM9G45
>>> http://www.ronetix.at/pm9g45.html
>>>
>>> Signed-off-by: Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>>> Cc: Nicolas Ferre <nicolas.ferre@atmel.com>
>>
>> Ok, queued in at91-3.8-dt branch.
>>
>> I had to modify the Makefile part of it to match current move to
>> arch/arm/boot/dts/Makefile.
>>
>> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
> I prefer to go via linus W I've other updte for the macb on the top of it
Fine... Be careful about macb, there are many things happening right now
in net-next for this interface!
> ditto for the rm9200
Noted. Thanks.
Bye,
>>> ---
>>> arch/arm/boot/dts/Makefile | 1 +
>>> arch/arm/boot/dts/pm9g45.dts | 144 ++++++++++++++++++++++++++++++++++++++++++
>>> 2 files changed, 145 insertions(+)
>>> create mode 100644 arch/arm/boot/dts/pm9g45.dts
>>>
>>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>>> index a9b051a..627b6ad 100644
>>> --- a/arch/arm/boot/dts/Makefile
>>> +++ b/arch/arm/boot/dts/Makefile
>>> @@ -19,6 +19,7 @@ dtb-$(CONFIG_ARCH_AT91) += tny_a9g20.dtb
>>> dtb-$(CONFIG_ARCH_AT91) += usb_a9g20.dtb
>>> # sam9g45
>>> dtb-$(CONFIG_ARCH_AT91) += at91sam9m10g45ek.dtb
>>> +dtb-$(CONFIG_ARCH_AT91) += pm9g45.dtb
>>> # sam9n12
>>> dtb-$(CONFIG_ARCH_AT91) += at91sam9n12ek.dtb
>>> # sam9x5
>>> diff --git a/arch/arm/boot/dts/pm9g45.dts b/arch/arm/boot/dts/pm9g45.dts
>>> new file mode 100644
>>> index 0000000..b0c258d
>>> --- /dev/null
>>> +++ b/arch/arm/boot/dts/pm9g45.dts
>>> @@ -0,0 +1,144 @@
>>> +/*
>>> + * pm9g45.dts - Device Tree file for Ronetix pm9g45 board
>>> + *
>>> + * Copyright (C) 2012 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com>
>>> + *
>>> + * Licensed under GPLv2.
>>> + */
>>> +/dts-v1/;
>>> +/include/ "at91sam9g45.dtsi"
>>> +
>>> +/ {
>>> + model = "Ronetix pm9g45";
>>> + compatible = "ronetix,pm9g45", "atmel,at91sam9g45", "atmel,at91sam9";
>>> +
>>> + chosen {
>>> + bootargs = "console=ttyS0,115200";
>>> + };
>>> +
>>> + memory {
>>> + reg = <0x70000000 0x8000000>;
>>> + };
>>> +
>>> + clocks {
>>> + #address-cells = <1>;
>>> + #size-cells = <1>;
>>> + ranges;
>>> +
>>> + main_clock: clock at 0 {
>>> + compatible = "atmel,osc", "fixed-clock";
>>> + clock-frequency = <12000000>;
>>> + };
>>> + };
>>> +
>>> + ahb {
>>> + apb {
>>> + dbgu: serial at ffffee00 {
>>> + status = "okay";
>>> + };
>>> +
>>> + pinctrl at fffff200 {
>>> +
>>> + board {
>>> + pinctrl_board_nand: nand0-board {
>>> + atmel,pins =
>>> + <3 3 0x0 0x1 /* PD3 gpio RDY pin pull_up*/
>>> + 2 14 0x0 0x1>; /* PC14 gpio enable pin pull_up */
>>> + };
>>> + };
>>> + };
>>> +
>>> + macb0: ethernet at fffbc000 {
>>> + phy-mode = "rmii";
>>> + status = "okay";
>>> + };
>>> + };
>>> +
>>> + nand0: nand at 40000000 {
>>> + nand-bus-width = <8>;
>>> + nand-ecc-mode = "soft";
>>> + nand-on-flash-bbt;
>>> + pinctrl-0 = <&pinctrl_board_nand>;
>>> +
>>> + gpios = <&pioD 3 0
>>> + &pioC 14 0
>>> + 0
>>> + >;
>>> +
>>> + status = "okay";
>>> +
>>> + at91bootstrap at 0 {
>>> + label = "at91bootstrap";
>>> + reg = <0x0 0x20000>;
>>> + };
>>> +
>>> + barebox at 20000 {
>>> + label = "barebox";
>>> + reg = <0x20000 0x40000>;
>>> + };
>>> +
>>> + bareboxenv at 60000 {
>>> + label = "bareboxenv";
>>> + reg = <0x60000 0x1A0000>;
>>> + };
>>> +
>>> + kernel at 200000 {
>>> + label = "bareboxenv2";
>>> + reg = <0x200000 0x300000>;
>>> + };
>>> +
>>> + kernel at 500000 {
>>> + label = "root";
>>> + reg = <0x500000 0x400000>;
>>> + };
>>> +
>>> + data at 900000 {
>>> + label = "data";
>>> + reg = <0x900000 0x8340000>;
>>> + };
>>> + };
>>> +
>>> + usb0: ohci at 00700000 {
>>> + status = "okay";
>>> + num-ports = <2>;
>>> + };
>>> +
>>> + usb1: ehci at 00800000 {
>>> + status = "okay";
>>> + };
>>> + };
>>> +
>>> + leds {
>>> + compatible = "gpio-leds";
>>> +
>>> + led0 {
>>> + label = "led0";
>>> + gpios = <&pioD 0 1>;
>>> + linux,default-trigger = "nand-disk";
>>> + };
>>> +
>>> + led1 {
>>> + label = "led1";
>>> + gpios = <&pioD 31 0>;
>>> + linux,default-trigger = "heartbeat";
>>> + };
>>> + };
>>> +
>>> + gpio_keys {
>>> + compatible = "gpio-keys";
>>> + #address-cells = <1>;
>>> + #size-cells = <0>;
>>> +
>>> + right {
>>> + label = "SW4";
>>> + gpios = <&pioE 7 1>;
>>> + linux,code = <106>;
>>> + };
>>> +
>>> + up {
>>> + label = "SW3";
>>> + gpios = <&pioE 8 1>;
>>> + linux,code = <103>;
>>> + };
>>> + };
>>> +};
>>>
>>
>>
>> --
>> Nicolas Ferre
>
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2012-11-16 13:32 UTC | newest]
Thread overview: 4+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2012-10-19 2:19 [PATCH 1/1] arm: at91: add Ronetix pm9g45 board support Jean-Christophe PLAGNIOL-VILLARD
2012-11-16 13:08 ` Nicolas Ferre
2012-11-16 13:28 ` Jean-Christophe PLAGNIOL-VILLARD
2012-11-16 13:32 ` Nicolas Ferre
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).