* SMDKV210 support issue in kernel 3.8 (dma-pl330 and HDMI failed) [not found] <51275DF7.4010600@gmail.com> @ 2013-02-26 21:22 ` Sylwester Nawrocki 2013-02-27 10:51 ` Inderpal Singh 0 siblings, 1 reply; 5+ messages in thread From: Sylwester Nawrocki @ 2013-02-26 21:22 UTC (permalink / raw) To: linux-arm-kernel On 02/22/2013 01:00 PM, Lonsn wrote: > Hi, > I have tested the kernel 3.8 with a SMDKV210 like board. But I failed > with dma-pl330 and HDMI driver. > For dma-pl330, kernel print: > dma-pl330 dma-pl330.0: PERIPH_ID 0x0, PCELL_ID 0x0 ! > dma-pl330: probe of dma-pl330.0 failed with error -22 > dma-pl330 dma-pl330.1: PERIPH_ID 0x0, PCELL_ID 0x0 ! > dma-pl330: probe of dma-pl330.1 failed with error -22 Maybe there is some issue with the PL330 DMA controller clocks and the read values are all 0 because the clocks are disabled ? It seems arch/arm/mach-s5pv210/clock.c might be missing "apb_pclk" clock supply names, which I suspect may be required after commits: commit 7c71b8eb268ee38235f7e924d943ea9d90e59469 Author: Inderpal Singh <inderpal.singh@linaro.org> Date: Fri Sep 7 12:14:48 2012 +0530 DMA: PL330: Remove redundant runtime_suspend/resume functions The driver's runtime_suspend/resume functions just disable/enable the clock which is already being managed at AMBA bus level runtime_suspend/resume functions. Hence, remove the driver's runtime_suspend/resume functions. Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> Tested-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com> commit faf6fbc6f2ca3b34bf464a8bb079a998e571957c Author: Inderpal Singh <inderpal.singh@linaro.org> Date: Fri Sep 7 12:14:47 2012 +0530 DMA: PL330: Remove controller clock enable/disable The controller clock is being enabled/disabled in AMBA bus infrastructre in probe/remove functions. Hence, its not required at driver level probe/remove. Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> Tested-by: Chander Kashyap <chander.kashyap@linaro.org> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com> I have added people who made related changes at Cc, hopefully they can provide some help in debugging this. Please try the following change: 8<-------------------- diff --git a/arch/arm/mach-s5pv210/clock.c b/arch/arm/mach-s5pv210/clock.c index fcdf52d..87c7d3f 100644 --- a/arch/arm/mach-s5pv210/clock.c +++ b/arch/arm/mach-s5pv210/clock.c @@ -214,11 +214,6 @@ static struct clk clk_pcmcdclk2 = { .name = "pcmcdclk", }; -static struct clk dummy_apb_pclk = { - .name = "apb_pclk", - .id = -1, -}; - static struct clk *clkset_vpllsrc_list[] = { [0] = &clk_fin_vpll, [1] = &clk_sclk_hdmi27m, @@ -1333,6 +1328,8 @@ static struct clk_lookup s5pv210_clk_lookup[] = { CLKDEV_INIT(NULL, "spi_busclk0", &clk_p), CLKDEV_INIT("s5pv210-spi.0", "spi_busclk1", &clk_sclk_spi0.clk), CLKDEV_INIT("s5pv210-spi.1", "spi_busclk1", &clk_sclk_spi1.clk), + CLKDEV_INIT("dma-pl330.0", "apb_pclk", &init_clocks_off[0]), + CLKDEV_INIT("dma-pl330.1", "apb_pclk", &init_clocks_off[1]), }; void __init s5pv210_register_clocks(void) @@ -1361,6 +1358,5 @@ void __init s5pv210_register_clocks(void) for (ptr = 0; ptr < ARRAY_SIZE(clk_cdev); ptr++) s3c_disable_clocks(clk_cdev[ptr], 1); - s3c24xx_register_clock(&dummy_apb_pclk); s3c_pwmclk_init(); } 8<-------------------- If it works then we could make some cleaner patch. > For HDMI driver, > I have added the following HDMI related code to > arch/arm/mach-s5pv210/mach-smdkv210.c: > /* I2C module and id for HDMIPHY */ > static struct i2c_board_info hdmiphy_info = { > I2C_BOARD_INFO("hdmiphy-s5pv210", 0x38), > }; > > i2c_register_board_info(2, smdkv210_i2c_devs2, > ARRAY_SIZE(smdkv210_i2c_devs2)); > > s5p_i2c_hdmiphy_set_platdata(NULL); > s5p_hdmi_set_platdata(&hdmiphy_info, NULL, 0); > > s3c_ide_set_platdata(&smdkv210_ide_pdata); > > then kernel print: > s5p-hdmi s5pv210-hdmi: hdmiphy adapter request failed > s5p-hdmi s5pv210-hdmi: probe failed > Samsung TV Mixer driver, (c) 2010-2011 Samsung Electronics Co., Ltd. > > s5p-mixer s5p-mixer: probe start > s5p-mixer s5p-mixer: resources acquired > s5p-mixer s5p-mixer: module s5p-hdmi provides no subdev! > s5p-mixer s5p-mixer: module s5p-sdo provides no subdev! > s5p-mixer s5p-mixer: failed to register any output > s5p-mixer s5p-mixer: probe failed > > Can anybody help me on how to config the HDMI output function in linux > kernel 3.8? I mainly want to do video hardware decode using s5pv210 MFC > and then display with HDMI. For video playback (video post-processing) you might also need at least one FIMC device. Please refer to arch/arm/mach-goni.c for an example on how to add related devices to your board. You don't need the camera stuff, just add: &s5p_device_mfc, &s5p_device_mfc_l, &s5p_device_mfc_r, &s5p_device_fimc0, &s5p_device_fimc1, &s5p_device_fimc2, &s5p_device_fimc_md, to smdkv210_devices[] and related Kconfig entries to make it compile. You'll need a function similar to goni_reserve() in your board file to reserve memory for the video codec. Hope that helps. ^ permalink raw reply related [flat|nested] 5+ messages in thread
* SMDKV210 support issue in kernel 3.8 (dma-pl330 and HDMI failed) 2013-02-26 21:22 ` SMDKV210 support issue in kernel 3.8 (dma-pl330 and HDMI failed) Sylwester Nawrocki @ 2013-02-27 10:51 ` Inderpal Singh 2013-02-27 11:22 ` Sylwester Nawrocki 2013-02-27 15:22 ` Lonsn 0 siblings, 2 replies; 5+ messages in thread From: Inderpal Singh @ 2013-02-27 10:51 UTC (permalink / raw) To: linux-arm-kernel On 27 February 2013 02:52, Sylwester Nawrocki <sylvester.nawrocki@gmail.com> wrote: > On 02/22/2013 01:00 PM, Lonsn wrote: >> >> Hi, >> I have tested the kernel 3.8 with a SMDKV210 like board. But I failed >> with dma-pl330 and HDMI driver. >> For dma-pl330, kernel print: >> dma-pl330 dma-pl330.0: PERIPH_ID 0x0, PCELL_ID 0x0 ! >> dma-pl330: probe of dma-pl330.0 failed with error -22 >> dma-pl330 dma-pl330.1: PERIPH_ID 0x0, PCELL_ID 0x0 ! >> dma-pl330: probe of dma-pl330.1 failed with error -22 > > > Maybe there is some issue with the PL330 DMA controller clocks and the > read values are all 0 because the clocks are disabled ? > > It seems arch/arm/mach-s5pv210/clock.c might be missing "apb_pclk" clock > supply names, which I suspect may be required after commits: > > commit 7c71b8eb268ee38235f7e924d943ea9d90e59469 > Author: Inderpal Singh <inderpal.singh@linaro.org> > Date: Fri Sep 7 12:14:48 2012 +0530 > > DMA: PL330: Remove redundant runtime_suspend/resume functions > > The driver's runtime_suspend/resume functions just disable/enable > the clock which is already being managed at AMBA bus level > runtime_suspend/resume functions. > > Hence, remove the driver's runtime_suspend/resume functions. > > Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> > Tested-by: Chander Kashyap <chander.kashyap@linaro.org> > Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com> > > commit faf6fbc6f2ca3b34bf464a8bb079a998e571957c > Author: Inderpal Singh <inderpal.singh@linaro.org> > Date: Fri Sep 7 12:14:47 2012 +0530 > > DMA: PL330: Remove controller clock enable/disable > > The controller clock is being enabled/disabled in AMBA bus > infrastructre in probe/remove functions. Hence, its not required > at driver level probe/remove. > > Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> > Tested-by: Chander Kashyap <chander.kashyap@linaro.org> > Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com> > > I have added people who made related changes at Cc, hopefully they > can provide some help in debugging this. > The mentioned patches just removed the redundant clock enable/disable from the driver as clock is already being managed at amba bus level in the same code path. As per my understanding the issue should come even without these patches. @Lonsn: Can you please test without these patches? Thanks, Inder > Please try the following change: > > 8<-------------------- > diff --git a/arch/arm/mach-s5pv210/clock.c b/arch/arm/mach-s5pv210/clock.c > index fcdf52d..87c7d3f 100644 > --- a/arch/arm/mach-s5pv210/clock.c > +++ b/arch/arm/mach-s5pv210/clock.c > @@ -214,11 +214,6 @@ static struct clk clk_pcmcdclk2 = { > .name = "pcmcdclk", > }; > > -static struct clk dummy_apb_pclk = { > - .name = "apb_pclk", > - .id = -1, > -}; > - > static struct clk *clkset_vpllsrc_list[] = { > [0] = &clk_fin_vpll, > [1] = &clk_sclk_hdmi27m, > @@ -1333,6 +1328,8 @@ static struct clk_lookup s5pv210_clk_lookup[] = { > CLKDEV_INIT(NULL, "spi_busclk0", &clk_p), > CLKDEV_INIT("s5pv210-spi.0", "spi_busclk1", &clk_sclk_spi0.clk), > CLKDEV_INIT("s5pv210-spi.1", "spi_busclk1", &clk_sclk_spi1.clk), > + CLKDEV_INIT("dma-pl330.0", "apb_pclk", &init_clocks_off[0]), > + CLKDEV_INIT("dma-pl330.1", "apb_pclk", &init_clocks_off[1]), > }; > > void __init s5pv210_register_clocks(void) > @@ -1361,6 +1358,5 @@ void __init s5pv210_register_clocks(void) > for (ptr = 0; ptr < ARRAY_SIZE(clk_cdev); ptr++) > s3c_disable_clocks(clk_cdev[ptr], 1); > > - s3c24xx_register_clock(&dummy_apb_pclk); > s3c_pwmclk_init(); > } > 8<-------------------- > > If it works then we could make some cleaner patch. > > >> For HDMI driver, >> I have added the following HDMI related code to >> arch/arm/mach-s5pv210/mach-smdkv210.c: >> /* I2C module and id for HDMIPHY */ >> static struct i2c_board_info hdmiphy_info = { >> I2C_BOARD_INFO("hdmiphy-s5pv210", 0x38), >> }; >> >> i2c_register_board_info(2, smdkv210_i2c_devs2, >> ARRAY_SIZE(smdkv210_i2c_devs2)); >> >> s5p_i2c_hdmiphy_set_platdata(NULL); >> s5p_hdmi_set_platdata(&hdmiphy_info, NULL, 0); >> >> s3c_ide_set_platdata(&smdkv210_ide_pdata); >> >> then kernel print: >> s5p-hdmi s5pv210-hdmi: hdmiphy adapter request failed >> s5p-hdmi s5pv210-hdmi: probe failed >> Samsung TV Mixer driver, (c) 2010-2011 Samsung Electronics Co., Ltd. >> >> s5p-mixer s5p-mixer: probe start >> s5p-mixer s5p-mixer: resources acquired >> s5p-mixer s5p-mixer: module s5p-hdmi provides no subdev! >> s5p-mixer s5p-mixer: module s5p-sdo provides no subdev! >> s5p-mixer s5p-mixer: failed to register any output >> s5p-mixer s5p-mixer: probe failed >> >> Can anybody help me on how to config the HDMI output function in linux >> kernel 3.8? I mainly want to do video hardware decode using s5pv210 MFC >> and then display with HDMI. > > > For video playback (video post-processing) you might also need at least one > FIMC device. Please refer to arch/arm/mach-goni.c for an example on how to > add related devices to your board. You don't need the camera stuff, just > add: > > &s5p_device_mfc, > &s5p_device_mfc_l, > &s5p_device_mfc_r, > > &s5p_device_fimc0, > &s5p_device_fimc1, > &s5p_device_fimc2, > &s5p_device_fimc_md, > > to smdkv210_devices[] and related Kconfig entries to make it compile. > You'll need a function similar to goni_reserve() in your board file > to reserve memory for the video codec. > > Hope that helps. ^ permalink raw reply [flat|nested] 5+ messages in thread
* SMDKV210 support issue in kernel 3.8 (dma-pl330 and HDMI failed) 2013-02-27 10:51 ` Inderpal Singh @ 2013-02-27 11:22 ` Sylwester Nawrocki 2013-02-27 15:32 ` Inderpal Singh 2013-02-27 15:22 ` Lonsn 1 sibling, 1 reply; 5+ messages in thread From: Sylwester Nawrocki @ 2013-02-27 11:22 UTC (permalink / raw) To: linux-arm-kernel On 02/27/2013 11:51 AM, Inderpal Singh wrote: > On 27 February 2013 02:52, Sylwester Nawrocki > <sylvester.nawrocki@gmail.com> wrote: >> On 02/22/2013 01:00 PM, Lonsn wrote: >>> >>> Hi, >>> I have tested the kernel 3.8 with a SMDKV210 like board. But I failed >>> with dma-pl330 and HDMI driver. >>> For dma-pl330, kernel print: >>> dma-pl330 dma-pl330.0: PERIPH_ID 0x0, PCELL_ID 0x0 ! >>> dma-pl330: probe of dma-pl330.0 failed with error -22 >>> dma-pl330 dma-pl330.1: PERIPH_ID 0x0, PCELL_ID 0x0 ! >>> dma-pl330: probe of dma-pl330.1 failed with error -22 >> >> >> Maybe there is some issue with the PL330 DMA controller clocks and the >> read values are all 0 because the clocks are disabled ? >> >> It seems arch/arm/mach-s5pv210/clock.c might be missing "apb_pclk" clock >> supply names, which I suspect may be required after commits: >> >> commit 7c71b8eb268ee38235f7e924d943ea9d90e59469 >> Author: Inderpal Singh <inderpal.singh@linaro.org> >> Date: Fri Sep 7 12:14:48 2012 +0530 >> >> DMA: PL330: Remove redundant runtime_suspend/resume functions >> >> The driver's runtime_suspend/resume functions just disable/enable >> the clock which is already being managed at AMBA bus level >> runtime_suspend/resume functions. >> >> Hence, remove the driver's runtime_suspend/resume functions. >> >> Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> >> Tested-by: Chander Kashyap <chander.kashyap@linaro.org> >> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com> >> >> commit faf6fbc6f2ca3b34bf464a8bb079a998e571957c >> Author: Inderpal Singh <inderpal.singh@linaro.org> >> Date: Fri Sep 7 12:14:47 2012 +0530 >> >> DMA: PL330: Remove controller clock enable/disable >> >> The controller clock is being enabled/disabled in AMBA bus >> infrastructre in probe/remove functions. Hence, its not required >> at driver level probe/remove. >> >> Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> >> Tested-by: Chander Kashyap <chander.kashyap@linaro.org> >> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com> >> >> I have added people who made related changes at Cc, hopefully they >> can provide some help in debugging this. >> > > The mentioned patches just removed the redundant clock enable/disable > from the driver as clock is already being managed at amba bus level in > the same code path. As per my understanding the issue should come even > without these patches. But were the clocks managed directly by the pl330 driver same as those managed at amba bus level ? The first patch as above removed chunk @@ -2887,24 +2884,17 @@ pl330_probe(struct amba_device *adev, const struct amba_id *id) goto probe_err1; } - pdmac->clk = clk_get(&adev->dev, "dma"); - if (IS_ERR(pdmac->clk)) { - dev_err(&adev->dev, "Cannot get operation clock.\n"); - ret = -EINVAL; - goto probe_err2; - } - which suggest the driver was enabling directly "dma" clocks, defined at S5PV210 platform level as: { .name = "dma", .devname = "dma-pl330.0", .parent = &clk_hclk_psys.clk, .enable = s5pv210_clk_ip0_ctrl, .ctrlbit = (1 << 3), }, { .name = "dma", .devname = "dma-pl330.1", .parent = &clk_hclk_psys.clk, .enable = s5pv210_clk_ip0_ctrl, .ctrlbit = (1 << 4), }, { And amba bus was getting only dummy clocks behind "apb_pclk" clock conn_id. > @Lonsn: Can you please test without these patches? I suspect reverting only patch DMA: PL330: Remove redundant runtime_suspend/resume functions with PM_RUNTIME enabled might fix the issue. -- Regards, Sylwester ^ permalink raw reply [flat|nested] 5+ messages in thread
* SMDKV210 support issue in kernel 3.8 (dma-pl330 and HDMI failed) 2013-02-27 11:22 ` Sylwester Nawrocki @ 2013-02-27 15:32 ` Inderpal Singh 0 siblings, 0 replies; 5+ messages in thread From: Inderpal Singh @ 2013-02-27 15:32 UTC (permalink / raw) To: linux-arm-kernel On 27 February 2013 16:52, Sylwester Nawrocki <s.nawrocki@samsung.com> wrote: > On 02/27/2013 11:51 AM, Inderpal Singh wrote: >> On 27 February 2013 02:52, Sylwester Nawrocki >> <sylvester.nawrocki@gmail.com> wrote: >>> On 02/22/2013 01:00 PM, Lonsn wrote: >>>> >>>> Hi, >>>> I have tested the kernel 3.8 with a SMDKV210 like board. But I failed >>>> with dma-pl330 and HDMI driver. >>>> For dma-pl330, kernel print: >>>> dma-pl330 dma-pl330.0: PERIPH_ID 0x0, PCELL_ID 0x0 ! >>>> dma-pl330: probe of dma-pl330.0 failed with error -22 >>>> dma-pl330 dma-pl330.1: PERIPH_ID 0x0, PCELL_ID 0x0 ! >>>> dma-pl330: probe of dma-pl330.1 failed with error -22 >>> >>> >>> Maybe there is some issue with the PL330 DMA controller clocks and the >>> read values are all 0 because the clocks are disabled ? >>> >>> It seems arch/arm/mach-s5pv210/clock.c might be missing "apb_pclk" clock >>> supply names, which I suspect may be required after commits: >>> >>> commit 7c71b8eb268ee38235f7e924d943ea9d90e59469 >>> Author: Inderpal Singh <inderpal.singh@linaro.org> >>> Date: Fri Sep 7 12:14:48 2012 +0530 >>> >>> DMA: PL330: Remove redundant runtime_suspend/resume functions >>> >>> The driver's runtime_suspend/resume functions just disable/enable >>> the clock which is already being managed at AMBA bus level >>> runtime_suspend/resume functions. >>> >>> Hence, remove the driver's runtime_suspend/resume functions. >>> >>> Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> >>> Tested-by: Chander Kashyap <chander.kashyap@linaro.org> >>> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com> >>> >>> commit faf6fbc6f2ca3b34bf464a8bb079a998e571957c >>> Author: Inderpal Singh <inderpal.singh@linaro.org> >>> Date: Fri Sep 7 12:14:47 2012 +0530 >>> >>> DMA: PL330: Remove controller clock enable/disable >>> >>> The controller clock is being enabled/disabled in AMBA bus >>> infrastructre in probe/remove functions. Hence, its not required >>> at driver level probe/remove. >>> >>> Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> >>> Tested-by: Chander Kashyap <chander.kashyap@linaro.org> >>> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com> >>> >>> I have added people who made related changes at Cc, hopefully they >>> can provide some help in debugging this. >>> >> >> The mentioned patches just removed the redundant clock enable/disable >> from the driver as clock is already being managed at amba bus level in >> the same code path. As per my understanding the issue should come even >> without these patches. > > But were the clocks managed directly by the pl330 driver same as those > managed at amba bus level ? The first patch as above removed chunk > > @@ -2887,24 +2884,17 @@ pl330_probe(struct amba_device *adev, const struct > amba_id *id) > goto probe_err1; > } > > - pdmac->clk = clk_get(&adev->dev, "dma"); > - if (IS_ERR(pdmac->clk)) { > - dev_err(&adev->dev, "Cannot get operation clock.\n"); > - ret = -EINVAL; > - goto probe_err2; > - } > - > > which suggest the driver was enabling directly "dma" clocks, defined at > S5PV210 platform level as: > > { > .name = "dma", > .devname = "dma-pl330.0", > .parent = &clk_hclk_psys.clk, > .enable = s5pv210_clk_ip0_ctrl, > .ctrlbit = (1 << 3), > }, { > .name = "dma", > .devname = "dma-pl330.1", > .parent = &clk_hclk_psys.clk, > .enable = s5pv210_clk_ip0_ctrl, > .ctrlbit = (1 << 4), > }, { > > And amba bus was getting only dummy clocks behind "apb_pclk" clock > conn_id. > Ahh Yes, I had missed this point. So the changes you suggested needs to be done as confirmed by Lonsn. Thanks Lonsn for bringing this up :-) Regards, Inder >> @Lonsn: Can you please test without these patches? > > I suspect reverting only patch > DMA: PL330: Remove redundant runtime_suspend/resume functions > with PM_RUNTIME enabled might fix the issue. > > -- > > Regards, > Sylwester ^ permalink raw reply [flat|nested] 5+ messages in thread
* SMDKV210 support issue in kernel 3.8 (dma-pl330 and HDMI failed) 2013-02-27 10:51 ` Inderpal Singh 2013-02-27 11:22 ` Sylwester Nawrocki @ 2013-02-27 15:22 ` Lonsn 1 sibling, 0 replies; 5+ messages in thread From: Lonsn @ 2013-02-27 15:22 UTC (permalink / raw) To: linux-arm-kernel ? 2013/2/27 18:51, Inderpal Singh ??: > On 27 February 2013 02:52, Sylwester Nawrocki > <sylvester.nawrocki@gmail.com> wrote: >> On 02/22/2013 01:00 PM, Lonsn wrote: >>> >>> Hi, >>> I have tested the kernel 3.8 with a SMDKV210 like board. But I failed >>> with dma-pl330 and HDMI driver. >>> For dma-pl330, kernel print: >>> dma-pl330 dma-pl330.0: PERIPH_ID 0x0, PCELL_ID 0x0 ! >>> dma-pl330: probe of dma-pl330.0 failed with error -22 >>> dma-pl330 dma-pl330.1: PERIPH_ID 0x0, PCELL_ID 0x0 ! >>> dma-pl330: probe of dma-pl330.1 failed with error -22 >> >> >> Maybe there is some issue with the PL330 DMA controller clocks and the >> read values are all 0 because the clocks are disabled ? >> >> It seems arch/arm/mach-s5pv210/clock.c might be missing "apb_pclk" clock >> supply names, which I suspect may be required after commits: >> >> commit 7c71b8eb268ee38235f7e924d943ea9d90e59469 >> Author: Inderpal Singh <inderpal.singh@linaro.org> >> Date: Fri Sep 7 12:14:48 2012 +0530 >> >> DMA: PL330: Remove redundant runtime_suspend/resume functions >> >> The driver's runtime_suspend/resume functions just disable/enable >> the clock which is already being managed at AMBA bus level >> runtime_suspend/resume functions. >> >> Hence, remove the driver's runtime_suspend/resume functions. >> >> Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> >> Tested-by: Chander Kashyap <chander.kashyap@linaro.org> >> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com> >> >> commit faf6fbc6f2ca3b34bf464a8bb079a998e571957c >> Author: Inderpal Singh <inderpal.singh@linaro.org> >> Date: Fri Sep 7 12:14:47 2012 +0530 >> >> DMA: PL330: Remove controller clock enable/disable >> >> The controller clock is being enabled/disabled in AMBA bus >> infrastructre in probe/remove functions. Hence, its not required >> at driver level probe/remove. >> >> Signed-off-by: Inderpal Singh <inderpal.singh@linaro.org> >> Tested-by: Chander Kashyap <chander.kashyap@linaro.org> >> Signed-off-by: Vinod Koul <vinod.koul@linux.intel.com> >> >> I have added people who made related changes at Cc, hopefully they >> can provide some help in debugging this. >> > > The mentioned patches just removed the redundant clock enable/disable > from the driver as clock is already being managed at amba bus level in > the same code path. As per my understanding the issue should come even > without these patches. > > @Lonsn: Can you please test without these patches? Inder, I have made the DMA clock change according to Sylwester's suggetstions and it works! Now kernel prints: ------------------------------------> io scheduler noop registered io scheduler deadline registered io scheduler cfq registered (default) s3c-fb s5pv210-fb: window 0: fb dma-pl330 dma-pl330.0: Loaded driver for PL330 DMAC-267056 dma-pl330 dma-pl330.0: DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 dma-pl330 dma-pl330.1: Loaded driver for PL330 DMAC-267056 dma-pl330 dma-pl330.1: DBUFF-8x4bytes Num_Chans-8 Num_Peri-32 Num_Events-32 Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled s5pv210-uart.0: ttySAC0 at MMIO 0xe2900000 (irq = 74) is a S3C6400/10 ------------------------------------------> > > Thanks, > Inder > >> Please try the following change: >> >> 8<-------------------- >> diff --git a/arch/arm/mach-s5pv210/clock.c b/arch/arm/mach-s5pv210/clock.c >> index fcdf52d..87c7d3f 100644 >> --- a/arch/arm/mach-s5pv210/clock.c >> +++ b/arch/arm/mach-s5pv210/clock.c >> @@ -214,11 +214,6 @@ static struct clk clk_pcmcdclk2 = { >> .name = "pcmcdclk", >> }; >> >> -static struct clk dummy_apb_pclk = { >> - .name = "apb_pclk", >> - .id = -1, >> -}; >> - >> static struct clk *clkset_vpllsrc_list[] = { >> [0] = &clk_fin_vpll, >> [1] = &clk_sclk_hdmi27m, >> @@ -1333,6 +1328,8 @@ static struct clk_lookup s5pv210_clk_lookup[] = { >> CLKDEV_INIT(NULL, "spi_busclk0", &clk_p), >> CLKDEV_INIT("s5pv210-spi.0", "spi_busclk1", &clk_sclk_spi0.clk), >> CLKDEV_INIT("s5pv210-spi.1", "spi_busclk1", &clk_sclk_spi1.clk), >> + CLKDEV_INIT("dma-pl330.0", "apb_pclk", &init_clocks_off[0]), >> + CLKDEV_INIT("dma-pl330.1", "apb_pclk", &init_clocks_off[1]), >> }; >> >> void __init s5pv210_register_clocks(void) >> @@ -1361,6 +1358,5 @@ void __init s5pv210_register_clocks(void) >> for (ptr = 0; ptr < ARRAY_SIZE(clk_cdev); ptr++) >> s3c_disable_clocks(clk_cdev[ptr], 1); >> >> - s3c24xx_register_clock(&dummy_apb_pclk); >> s3c_pwmclk_init(); >> } >> 8<-------------------- >> >> If it works then we could make some cleaner patch. >> >> >>> For HDMI driver, >>> I have added the following HDMI related code to >>> arch/arm/mach-s5pv210/mach-smdkv210.c: >>> /* I2C module and id for HDMIPHY */ >>> static struct i2c_board_info hdmiphy_info = { >>> I2C_BOARD_INFO("hdmiphy-s5pv210", 0x38), >>> }; >>> >>> i2c_register_board_info(2, smdkv210_i2c_devs2, >>> ARRAY_SIZE(smdkv210_i2c_devs2)); >>> >>> s5p_i2c_hdmiphy_set_platdata(NULL); >>> s5p_hdmi_set_platdata(&hdmiphy_info, NULL, 0); >>> >>> s3c_ide_set_platdata(&smdkv210_ide_pdata); >>> >>> then kernel print: >>> s5p-hdmi s5pv210-hdmi: hdmiphy adapter request failed >>> s5p-hdmi s5pv210-hdmi: probe failed >>> Samsung TV Mixer driver, (c) 2010-2011 Samsung Electronics Co., Ltd. >>> >>> s5p-mixer s5p-mixer: probe start >>> s5p-mixer s5p-mixer: resources acquired >>> s5p-mixer s5p-mixer: module s5p-hdmi provides no subdev! >>> s5p-mixer s5p-mixer: module s5p-sdo provides no subdev! >>> s5p-mixer s5p-mixer: failed to register any output >>> s5p-mixer s5p-mixer: probe failed >>> >>> Can anybody help me on how to config the HDMI output function in linux >>> kernel 3.8? I mainly want to do video hardware decode using s5pv210 MFC >>> and then display with HDMI. >> >> >> For video playback (video post-processing) you might also need at least one >> FIMC device. Please refer to arch/arm/mach-goni.c for an example on how to >> add related devices to your board. You don't need the camera stuff, just >> add: >> >> &s5p_device_mfc, >> &s5p_device_mfc_l, >> &s5p_device_mfc_r, >> >> &s5p_device_fimc0, >> &s5p_device_fimc1, >> &s5p_device_fimc2, >> &s5p_device_fimc_md, >> >> to smdkv210_devices[] and related Kconfig entries to make it compile. >> You'll need a function similar to goni_reserve() in your board file >> to reserve memory for the video codec. >> >> Hope that helps. Yes, I have added fimc0,fimc1,fimc2,fimc_md and reserve MFC memory. But currently HDMI output doesn't work correctly yet, I would try to see the HDMI output first and then video decoder. Regards, ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2013-02-27 15:32 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <51275DF7.4010600@gmail.com>
2013-02-26 21:22 ` SMDKV210 support issue in kernel 3.8 (dma-pl330 and HDMI failed) Sylwester Nawrocki
2013-02-27 10:51 ` Inderpal Singh
2013-02-27 11:22 ` Sylwester Nawrocki
2013-02-27 15:32 ` Inderpal Singh
2013-02-27 15:22 ` Lonsn
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).