[PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons

[PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons

[Tushar Behera]

Added GPIO buttons DT node to Arndale board file.

Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
---
This series is based on for-next branch of Kukjin Kim's tree
and added on top of the below patch:
https://patchwork.kernel.org/patch/2042451/
---
 arch/arm/boot/dts/exynos5250-arndale.dts |   48 ++++++++++++++++++++++++++++++
 1 files changed, 48 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index 63572f9..9ce40df 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -119,4 +119,52 @@
 	spi_2: spi at 12d40000 {
 		status = "disabled";
 	};
+
+	gpio_keys {
+		compatible = "gpio-keys";
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		menu {
+			label = "SW-TACT2";
+			gpios = <&gpx1 4 0 0x10000 2>;
+			linux,code = <139>;
+			gpio-key,wakeup;
+		};
+
+		home {
+			label = "SW-TACT3";
+			gpios = <&gpx1 5 0 0x10000 2>;
+			linux,code = <102>;
+			gpio-key,wakeup;
+		};
+
+		up {
+			label = "SW-TACT4";
+			gpios = <&gpx1 6 0 0x10000 2>;
+			linux,code = <103>;
+			gpio-key,wakeup;
+		};
+
+		down {
+			label = "SW-TACT5";
+			gpios = <&gpx1 7 0 0x10000 2>;
+			linux,code = <108>;
+			gpio-key,wakeup;
+		};
+
+		back {
+			label = "SW-TACT6";
+			gpios = <&gpx2 0 0 0x10000 2>;
+			linux,code = <158>;
+			gpio-key,wakeup;
+		};
+
+		wakeup {
+			label = "SW-TACT7";
+			gpios = <&gpx2 1 0 0x10000 2>;
+			linux,code = <143>;
+			gpio-key,wakeup;
+		};
+	};
 };
-- 
1.7.4.1

[PATCH 2/5] ARM: dts: exynos5250-arndale: Add PMIC node entry

[Tushar Behera]

From: Amit Daniel Kachhap <amit.daniel@samsung.com>

Added S5M8767 PMIC DT nodes to Arndale board.

Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
---
 arch/arm/boot/dts/exynos5250-arndale.dts |  213 +++++++++++++++++++++++++++++-
 1 files changed, 212 insertions(+), 1 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index 9ce40df..b40a02f 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -25,7 +25,218 @@
 	};
 
 	i2c at 12C60000 {
-		status = "disabled";
+		status = "okay";
+		samsung,i2c-sda-delay = <100>;
+		samsung,i2c-max-bus-freq = <20000>;
+		samsung,i2c-slave-addr = <0x66>;
+		gpios = <&gpb3 0 2 3 0>,
+			<&gpb3 1 2 3 0>;
+
+		s5m8767_pmic at 66 {
+			compatible = "samsung,s5m8767-pmic";
+			reg = <0x66>;
+
+			s5m8767,pmic-buck2-dvs-voltage = <1300000>;
+			s5m8767,pmic-buck3-dvs-voltage = <1100000>;
+			s5m8767,pmic-buck4-dvs-voltage = <1200000>;
+			s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 1 0 0>,
+							<&gpd1 1 1 0 0>,
+							<&gpd1 2 1 0 0>;
+			s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>,
+							<&gpx2 4 1 0 0>,
+							<&gpx2 5 1 0 0>;
+			regulators {
+				ldo1_reg: LDO1 {
+					regulator-name = "VDD_ALIVE_1.0V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				ldo2_reg: LDO2 {
+					regulator-name = "VDD_28IO_DP_1.35V";
+					regulator-min-microvolt = <1200000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo3_reg: LDO3 {
+					regulator-name = "VDD_COMMON1_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo4_reg: LDO4 {
+					regulator-name = "VDD_IOPERI_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo5_reg: LDO5 {
+					regulator-name = "VDD_EXT_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo6_reg: LDO6 {
+					regulator-name = "VDD_MPLL_1.1V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo7_reg: LDO7 {
+					regulator-name = "VDD_XPLL_1.1V";
+					regulator-min-microvolt = <1100000>;
+					regulator-max-microvolt = <1100000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo8_reg: LDO8 {
+					regulator-name = "VDD_COMMON2_1.0V";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo9_reg: LDO9 {
+					regulator-name = "VDD_33ON_3.0V";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo10_reg: LDO10 {
+					regulator-name = "VDD_COMMON3_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo11_reg: LDO11 {
+					regulator-name = "VDD_ABB2_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo12_reg: LDO12 {
+					regulator-name = "VDD_USB_3.0V";
+					regulator-min-microvolt = <3000000>;
+					regulator-max-microvolt = <3000000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo13_reg: LDO13 {
+					regulator-name = "VDDQ_C2C_W_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo14_reg: LDO14 {
+					regulator-name = "VDD18_ABB0_3_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo15_reg: LDO15 {
+					regulator-name = "VDD10_COMMON4_1.0V";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo16_reg: LDO16 {
+					regulator-name = "VDD18_HSIC_1.8V";
+					regulator-min-microvolt = <1800000>;
+					regulator-max-microvolt = <1800000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo17_reg: LDO17 {
+					regulator-name = "VDDQ_MMC2_3_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				ldo18_reg: LDO18 {
+					regulator-name = "VDD_33ON_2.8V";
+					regulator-min-microvolt = <2800000>;
+					regulator-max-microvolt = <2800000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				buck1_reg: BUCK1 {
+					regulator-name = "VDD_MIF_1.2V";
+					regulator-min-microvolt = <950000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				buck2_reg: BUCK2 {
+					regulator-name = "vdd_arm";
+					regulator-min-microvolt = <925000>;
+					regulator-max-microvolt = <1300000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				buck3_reg: BUCK3 {
+					regulator-name = "VDD_INT_1.0V";
+					regulator-min-microvolt = <900000>;
+					regulator-max-microvolt = <1200000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+				buck4_reg: BUCK4 {
+					regulator-name = "VDD_G3D_1.0V";
+					regulator-min-microvolt = <1000000>;
+					regulator-max-microvolt = <1000000>;
+					regulator-always-on;
+					op_mode = <1>;
+				};
+
+				buck5_reg: BUCK5 {
+					regulator-name = "VDD_MEM_1.35V";
+					regulator-min-microvolt = <750000>;
+					regulator-max-microvolt = <1355000>;
+					regulator-always-on;
+					regulator-boot-on;
+					op_mode = <1>;
+				};
+
+			};
+		};
 	};
 
 	i2c at 12C70000 {
-- 
1.7.4.1

[PATCH 3/5] ARM: dts: exynos5250-arndale: Add vmmc regulator support

[Tushar Behera]

From: Sachin Kamat <sachin.kamat@linaro.org>

Added vmmc regulator node to Arndale DT file.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
---
 arch/arm/boot/dts/exynos5250-arndale.dts |   11 +++++++++++
 1 files changed, 11 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index b40a02f..d018fd2 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -280,6 +280,7 @@
 		samsung,dw-mshc-ciu-div = <3>;
 		samsung,dw-mshc-sdr-timing = <2 3>;
 		samsung,dw-mshc-ddr-timing = <1 2>;
+		vmmc-supply = <&mmc_reg>;
 
 		slot at 0 {
 			reg = <0>;
@@ -304,6 +305,7 @@
 		samsung,dw-mshc-ciu-div = <3>;
 		samsung,dw-mshc-sdr-timing = <2 3>;
 		samsung,dw-mshc-ddr-timing = <1 2>;
+		vmmc-supply = <&mmc_reg>;
 
 		slot at 0 {
 			reg = <0>;
@@ -378,4 +380,13 @@
 			gpio-key,wakeup;
 		};
 	};
+
+	mmc_reg: voltage-regulator {
+		compatible = "regulator-fixed";
+		regulator-name = "VDD_33ON_2.8V";
+		regulator-min-microvolt = <2800000>;
+		regulator-max-microvolt = <2800000>;
+		gpio = <&gpx1 1 0 0 2>;
+		enable-active-high;
+	};
 };
-- 
1.7.4.1

[PATCH 4/5] ARM: dts: exynos5250-arndale: Add MFC codec support

[Tushar Behera]

From: Sachin Kamat <sachin.kamat@linaro.org>

Added MFC codec node to Arndale DT file.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
---
 arch/arm/boot/dts/exynos5250-arndale.dts |    5 +++++
 1 files changed, 5 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index d018fd2..6162a72 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -24,6 +24,11 @@
 		bootargs = "console=ttySAC2,115200";
 	};
 
+	codec at 11000000 {
+		samsung,mfc-r = <0x43000000 0x800000>;
+		samsung,mfc-l = <0x51000000 0x800000>;
+	};
+
 	i2c at 12C60000 {
 		status = "okay";
 		samsung,i2c-sda-delay = <100>;
-- 
1.7.4.1

[PATCH 5/5] ARM: dts: exynos5250-arndale: Add HDMI HPD and regulator node

[Tushar Behera]

From: Sachin Kamat <sachin.kamat@linaro.org>

Added HDMI hot plug and regulator nodes to Arndale DT file.

Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
---
 arch/arm/boot/dts/exynos5250-arndale.dts |   12 ++++++++++++
 1 files changed, 12 insertions(+), 0 deletions(-)

diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
index 6162a72..7b891a9 100644
--- a/arch/arm/boot/dts/exynos5250-arndale.dts
+++ b/arch/arm/boot/dts/exynos5250-arndale.dts
@@ -386,6 +386,13 @@
 		};
 	};
 
+	hdmi {
+		hpd-gpio = <&gpx3 7 0xf 1 3>;
+		vdd_osc-supply = <&ldo10_reg>;
+		vdd_pll-supply = <&ldo8_reg>;
+		vdd-supply = <&ldo8_reg>;
+	};
+
 	mmc_reg: voltage-regulator {
 		compatible = "regulator-fixed";
 		regulator-name = "VDD_33ON_2.8V";
@@ -394,4 +401,9 @@
 		gpio = <&gpx1 1 0 0 2>;
 		enable-active-high;
 	};
+
+	reg_hdmi_en: fixedregulator at 0 {
+		compatible = "regulator-fixed";
+		regulator-name = "hdmi-en";
+	};
 };
-- 
1.7.4.1

[PATCH 2/5] ARM: dts: exynos5250-arndale: Add PMIC node entry

[Kumar, Anil]

On Thu, Feb 07, 2013 at 10:45:26, Tushar Behera wrote:
> From: Amit Daniel Kachhap <amit.daniel@samsung.com>
> 
> Added S5M8767 PMIC DT nodes to Arndale board.
> 
> Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
> Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
> ---
>  arch/arm/boot/dts/exynos5250-arndale.dts |  213 +++++++++++++++++++++++++++++-
>  1 files changed, 212 insertions(+), 1 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
> index 9ce40df..b40a02f 100644
> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
> @@ -25,7 +25,218 @@
>  	};
>  
>  	i2c at 12C60000 {
> -		status = "disabled";
> +		status = "okay";

Is there any need to change status "okay" here as in dtsi file it is
by default okay ?   

> +		samsung,i2c-sda-delay = <100>;
> +		samsung,i2c-max-bus-freq = <20000>;
> +		samsung,i2c-slave-addr = <0x66>;
> +		gpios = <&gpb3 0 2 3 0>,
> +			<&gpb3 1 2 3 0>;
> +
> +		s5m8767_pmic at 66 {
> +			compatible = "samsung,s5m8767-pmic";
> +			reg = <0x66>;
> +
> +			s5m8767,pmic-buck2-dvs-voltage = <1300000>;
> +			s5m8767,pmic-buck3-dvs-voltage = <1100000>;
> +			s5m8767,pmic-buck4-dvs-voltage = <1200000>;
> +			s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 1 0 0>,
> +							<&gpd1 1 1 0 0>,
> +							<&gpd1 2 1 0 0>;
> +			s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1 0 0>,
> +							<&gpx2 4 1 0 0>,
> +							<&gpx2 5 1 0 0>;
> +			regulators {
> +				ldo1_reg: LDO1 {
> +					regulator-name = "VDD_ALIVE_1.0V";
> +					regulator-min-microvolt = <1100000>;
> +					regulator-max-microvolt = <1100000>;
> +					regulator-always-on;
> +					regulator-boot-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo2_reg: LDO2 {
> +					regulator-name = "VDD_28IO_DP_1.35V";
> +					regulator-min-microvolt = <1200000>;
> +					regulator-max-microvolt = <1200000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo3_reg: LDO3 {
> +					regulator-name = "VDD_COMMON1_1.8V";
> +					regulator-min-microvolt = <1800000>;
> +					regulator-max-microvolt = <1800000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo4_reg: LDO4 {
> +					regulator-name = "VDD_IOPERI_1.8V";
> +					regulator-min-microvolt = <1800000>;
> +					regulator-max-microvolt = <1800000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo5_reg: LDO5 {
> +					regulator-name = "VDD_EXT_1.8V";
> +					regulator-min-microvolt = <1800000>;
> +					regulator-max-microvolt = <1800000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo6_reg: LDO6 {
> +					regulator-name = "VDD_MPLL_1.1V";
> +					regulator-min-microvolt = <1100000>;
> +					regulator-max-microvolt = <1100000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo7_reg: LDO7 {
> +					regulator-name = "VDD_XPLL_1.1V";
> +					regulator-min-microvolt = <1100000>;
> +					regulator-max-microvolt = <1100000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo8_reg: LDO8 {
> +					regulator-name = "VDD_COMMON2_1.0V";
> +					regulator-min-microvolt = <1000000>;
> +					regulator-max-microvolt = <1000000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo9_reg: LDO9 {
> +					regulator-name = "VDD_33ON_3.0V";
> +					regulator-min-microvolt = <3000000>;
> +					regulator-max-microvolt = <3000000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo10_reg: LDO10 {
> +					regulator-name = "VDD_COMMON3_1.8V";
> +					regulator-min-microvolt = <1800000>;
> +					regulator-max-microvolt = <1800000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo11_reg: LDO11 {
> +					regulator-name = "VDD_ABB2_1.8V";
> +					regulator-min-microvolt = <1800000>;
> +					regulator-max-microvolt = <1800000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo12_reg: LDO12 {
> +					regulator-name = "VDD_USB_3.0V";
> +					regulator-min-microvolt = <3000000>;
> +					regulator-max-microvolt = <3000000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo13_reg: LDO13 {
> +					regulator-name = "VDDQ_C2C_W_1.8V";
> +					regulator-min-microvolt = <1800000>;
> +					regulator-max-microvolt = <1800000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo14_reg: LDO14 {
> +					regulator-name = "VDD18_ABB0_3_1.8V";
> +					regulator-min-microvolt = <1800000>;
> +					regulator-max-microvolt = <1800000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo15_reg: LDO15 {
> +					regulator-name = "VDD10_COMMON4_1.0V";
> +					regulator-min-microvolt = <1000000>;
> +					regulator-max-microvolt = <1000000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo16_reg: LDO16 {
> +					regulator-name = "VDD18_HSIC_1.8V";
> +					regulator-min-microvolt = <1800000>;
> +					regulator-max-microvolt = <1800000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo17_reg: LDO17 {
> +					regulator-name = "VDDQ_MMC2_3_2.8V";
> +					regulator-min-microvolt = <2800000>;
> +					regulator-max-microvolt = <2800000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				ldo18_reg: LDO18 {
> +					regulator-name = "VDD_33ON_2.8V";
> +					regulator-min-microvolt = <2800000>;
> +					regulator-max-microvolt = <2800000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				buck1_reg: BUCK1 {
> +					regulator-name = "VDD_MIF_1.2V";
> +					regulator-min-microvolt = <950000>;
> +					regulator-max-microvolt = <1200000>;
> +					regulator-always-on;
> +					regulator-boot-on;
> +					op_mode = <1>;
> +				};
> +
> +				buck2_reg: BUCK2 {
> +					regulator-name = "vdd_arm";
> +					regulator-min-microvolt = <925000>;
> +					regulator-max-microvolt = <1300000>;
> +					regulator-always-on;
> +					regulator-boot-on;
> +					op_mode = <1>;
> +				};
> +
> +				buck3_reg: BUCK3 {
> +					regulator-name = "VDD_INT_1.0V";
> +					regulator-min-microvolt = <900000>;
> +					regulator-max-microvolt = <1200000>;
> +					regulator-always-on;
> +					regulator-boot-on;
> +					op_mode = <1>;
> +				};
> +
> +				buck4_reg: BUCK4 {
> +					regulator-name = "VDD_G3D_1.0V";
> +					regulator-min-microvolt = <1000000>;
> +					regulator-max-microvolt = <1000000>;
> +					regulator-always-on;
> +					op_mode = <1>;
> +				};
> +
> +				buck5_reg: BUCK5 {
> +					regulator-name = "VDD_MEM_1.35V";
> +					regulator-min-microvolt = <750000>;
> +					regulator-max-microvolt = <1355000>;
> +					regulator-always-on;
> +					regulator-boot-on;
> +					op_mode = <1>;
> +				};
> +
> +			};
> +		};
>  	};
>  
>  	i2c at 12C70000 {
> -- 
> 1.7.4.1
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> 

[PATCH 2/5] ARM: dts: exynos5250-arndale: Add PMIC node entry

[Tushar Behera]

On 02/07/2013 11:19 AM, Kumar, Anil wrote:
> On Thu, Feb 07, 2013 at 10:45:26, Tushar Behera wrote:
>> From: Amit Daniel Kachhap <amit.daniel@samsung.com>
>>
>> Added S5M8767 PMIC DT nodes to Arndale board.
>>
>> Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
>> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
>> Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
>> ---
>>  arch/arm/boot/dts/exynos5250-arndale.dts |  213 +++++++++++++++++++++++++++++-
>>  1 files changed, 212 insertions(+), 1 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
>> index 9ce40df..b40a02f 100644
>> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
>> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
>> @@ -25,7 +25,218 @@
>>  	};
>>  
>>  	i2c at 12C60000 {
>> -		status = "disabled";
>> +		status = "okay";
> 
> Is there any need to change status "okay" here as in dtsi file it is
> by default okay ?   
> 

Right, there is no need for setting it as "okay" explicitly.

-- 
Tushar Behera

[PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons

[Kumar, Anil]

On Thu, Feb 07, 2013 at 10:45:25, Tushar Behera wrote:
> Added GPIO buttons DT node to Arndale board file.
> 
> Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
> ---
> This series is based on for-next branch of Kukjin Kim's tree
> and added on top of the below patch:
> https://patchwork.kernel.org/patch/2042451/
> ---
>  arch/arm/boot/dts/exynos5250-arndale.dts |   48 ++++++++++++++++++++++++++++++
>  1 files changed, 48 insertions(+), 0 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
> index 63572f9..9ce40df 100644
> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
> @@ -119,4 +119,52 @@
>  	spi_2: spi at 12d40000 {
>  		status = "disabled";
>  	};
> +
> +	gpio_keys {
> +		compatible = "gpio-keys";
> +		#address-cells = <1>;
> +		#size-cells = <0>;

Just want to understand why these properties are here?  
As these properties are for child dt node. But have not seen
anyone is using here.

Sorry if I have misunderstood. 

> +
> +		menu {
> +			label = "SW-TACT2";
> +			gpios = <&gpx1 4 0 0x10000 2>;
> +			linux,code = <139>;
> +			gpio-key,wakeup;
> +		};
> +
> +		home {
> +			label = "SW-TACT3";
> +			gpios = <&gpx1 5 0 0x10000 2>;
> +			linux,code = <102>;
> +			gpio-key,wakeup;
> +		};
> +
> +		up {
> +			label = "SW-TACT4";
> +			gpios = <&gpx1 6 0 0x10000 2>;
> +			linux,code = <103>;
> +			gpio-key,wakeup;
> +		};
> +
> +		down {
> +			label = "SW-TACT5";
> +			gpios = <&gpx1 7 0 0x10000 2>;
> +			linux,code = <108>;
> +			gpio-key,wakeup;
> +		};
> +
> +		back {
> +			label = "SW-TACT6";
> +			gpios = <&gpx2 0 0 0x10000 2>;
> +			linux,code = <158>;
> +			gpio-key,wakeup;
> +		};
> +
> +		wakeup {
> +			label = "SW-TACT7";
> +			gpios = <&gpx2 1 0 0x10000 2>;
> +			linux,code = <143>;
> +			gpio-key,wakeup;
> +		};
> +	};
>  };
> -- 
> 1.7.4.1
> 
> 
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> 

[PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons

[Tushar Behera]

On 02/07/2013 11:47 AM, Kumar, Anil wrote:
> On Thu, Feb 07, 2013 at 10:45:25, Tushar Behera wrote:
>> Added GPIO buttons DT node to Arndale board file.
>>
>> Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
>> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
>> ---
>> This series is based on for-next branch of Kukjin Kim's tree
>> and added on top of the below patch:
>> https://patchwork.kernel.org/patch/2042451/
>> ---
>>  arch/arm/boot/dts/exynos5250-arndale.dts |   48 ++++++++++++++++++++++++++++++
>>  1 files changed, 48 insertions(+), 0 deletions(-)
>>
>> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
>> index 63572f9..9ce40df 100644
>> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
>> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
>> @@ -119,4 +119,52 @@
>>  	spi_2: spi at 12d40000 {
>>  		status = "disabled";
>>  	};
>> +
>> +	gpio_keys {
>> +		compatible = "gpio-keys";
>> +		#address-cells = <1>;
>> +		#size-cells = <0>;
> 
> Just want to understand why these properties are here?  
> As these properties are for child dt node. But have not seen
> anyone is using here.
> 

That is how gpio_keys node entries are defined in other .dts files.

-- 
Tushar Behera

[PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons

[Manish Badarkhe]

Hi Tushar

On Thu, Feb 7, 2013 at 11:56 AM, Tushar Behera <tushar.behera@linaro.org> wrote:
> On 02/07/2013 11:47 AM, Kumar, Anil wrote:
>> On Thu, Feb 07, 2013 at 10:45:25, Tushar Behera wrote:
>>> Added GPIO buttons DT node to Arndale board file.
>>>
>>> Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
>>> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
>>> ---
>>> This series is based on for-next branch of Kukjin Kim's tree
>>> and added on top of the below patch:
>>> https://patchwork.kernel.org/patch/2042451/
>>> ---
>>>  arch/arm/boot/dts/exynos5250-arndale.dts |   48 ++++++++++++++++++++++++++++++
>>>  1 files changed, 48 insertions(+), 0 deletions(-)
>>>
>>> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
>>> index 63572f9..9ce40df 100644
>>> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
>>> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
>>> @@ -119,4 +119,52 @@
>>>      spi_2: spi at 12d40000 {
>>>              status = "disabled";
>>>      };
>>> +
>>> +    gpio_keys {
>>> +            compatible = "gpio-keys";
>>> +            #address-cells = <1>;
>>> +            #size-cells = <0>;
>>
>> Just want to understand why these properties are here?
>> As these properties are for child dt node. But have not seen
>> anyone is using here.
>>
>
> That is how gpio_keys node entries are defined in other .dts files.

I have gone through example for address-cells and size-cells in following link:
http://devicetree.org/mediawiki/index.php?title=Device_Tree_Usage&stable=1#CPU_addressing

which indicates that these fields are for child "reg".
I think, here in child node there is no "reg". so there is no use
of address-cells and size-cells propeties.

Correct me if I am wrong here?

Thanks
Manish Badarkhe

[PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons

[Tushar Behera]

On 02/07/2013 12:06 PM, Manish Badarkhe wrote:
> Hi Tushar
> 
> On Thu, Feb 7, 2013 at 11:56 AM, Tushar Behera <tushar.behera@linaro.org> wrote:
>> On 02/07/2013 11:47 AM, Kumar, Anil wrote:
>>> On Thu, Feb 07, 2013 at 10:45:25, Tushar Behera wrote:
>>>> Added GPIO buttons DT node to Arndale board file.
>>>>
>>>> Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
>>>> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
>>>> ---
>>>> This series is based on for-next branch of Kukjin Kim's tree
>>>> and added on top of the below patch:
>>>> https://patchwork.kernel.org/patch/2042451/
>>>> ---
>>>>  arch/arm/boot/dts/exynos5250-arndale.dts |   48 ++++++++++++++++++++++++++++++
>>>>  1 files changed, 48 insertions(+), 0 deletions(-)
>>>>
>>>> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
>>>> index 63572f9..9ce40df 100644
>>>> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
>>>> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
>>>> @@ -119,4 +119,52 @@
>>>>      spi_2: spi at 12d40000 {
>>>>              status = "disabled";
>>>>      };
>>>> +
>>>> +    gpio_keys {
>>>> +            compatible = "gpio-keys";
>>>> +            #address-cells = <1>;
>>>> +            #size-cells = <0>;
>>>
>>> Just want to understand why these properties are here?
>>> As these properties are for child dt node. But have not seen
>>> anyone is using here.
>>>
>>
>> That is how gpio_keys node entries are defined in other .dts files.
> 
> I have gone through example for address-cells and size-cells in following link:
> http://devicetree.org/mediawiki/index.php?title=Device_Tree_Usage&stable=1#CPU_addressing
> 
> which indicates that these fields are for child "reg".
> I think, here in child node there is no "reg". so there is no use
> of address-cells and size-cells propeties.
> 

Please check Documentation/devicetree/bindings/gpio/gpio_keys.txt

And whether these properties are required or not, I will let device tree
experts to comment on that.

As such, currently all node entries for gpio_keys use these properties.

-- 
Tushar Behera

[PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons

[Girish KS]

On Wed, Feb 6, 2013 at 10:56 PM, Tushar Behera <tushar.behera@linaro.org> wrote:
> On 02/07/2013 12:06 PM, Manish Badarkhe wrote:
>> Hi Tushar
>>
>> On Thu, Feb 7, 2013 at 11:56 AM, Tushar Behera <tushar.behera@linaro.org> wrote:
>>> On 02/07/2013 11:47 AM, Kumar, Anil wrote:
>>>> On Thu, Feb 07, 2013 at 10:45:25, Tushar Behera wrote:
>>>>> Added GPIO buttons DT node to Arndale board file.
>>>>>
>>>>> Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
>>>>> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
>>>>> ---
>>>>> This series is based on for-next branch of Kukjin Kim's tree
>>>>> and added on top of the below patch:
>>>>> https://patchwork.kernel.org/patch/2042451/
>>>>> ---
>>>>>  arch/arm/boot/dts/exynos5250-arndale.dts |   48 ++++++++++++++++++++++++++++++
>>>>>  1 files changed, 48 insertions(+), 0 deletions(-)
>>>>>
>>>>> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
>>>>> index 63572f9..9ce40df 100644
>>>>> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
>>>>> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
>>>>> @@ -119,4 +119,52 @@
>>>>>      spi_2: spi at 12d40000 {
>>>>>              status = "disabled";
>>>>>      };
>>>>> +
>>>>> +    gpio_keys {
>>>>> +            compatible = "gpio-keys";
>>>>> +            #address-cells = <1>;
>>>>> +            #size-cells = <0>;
>>>>
>>>> Just want to understand why these properties are here?
>>>> As these properties are for child dt node. But have not seen
>>>> anyone is using here.
>>>>
>>>
>>> That is how gpio_keys node entries are defined in other .dts files.
>>
>> I have gone through example for address-cells and size-cells in following link:
>> http://devicetree.org/mediawiki/index.php?title=Device_Tree_Usage&stable=1#CPU_addressing
>>
>> which indicates that these fields are for child "reg".
>> I think, here in child node there is no "reg". so there is no use
>> of address-cells and size-cells propeties.
>>
>
> Please check Documentation/devicetree/bindings/gpio/gpio_keys.txt
>
> And whether these properties are required or not, I will let device tree
> experts to comment on that.
>
> As such, currently all node entries for gpio_keys use these properties.
you can just verify by a simple test.
delete the 2 lines. address-cells and size cells.
this will have no affect.
now with these 2 lines deleted lines add a dummy reg property with
address and cell. dtb compiler will warn.
So I think what manish reffered is right.
There is also a reference of smdk4210 for kepads.
>
> --
> Tushar Behera
>
> _______________________________________________
> linux-arm-kernel mailing list
> linux-arm-kernel at lists.infradead.org
> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel

[PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons

[Tushar Behera]

+CC: David Jander <david@protonic.nl>
+CC: Dmitry Torokhov <dtor@mail.ru>

On 02/07/2013 01:13 PM, Girish KS wrote:
>>>>>> +
>>>>>> +    gpio_keys {
>>>>>> +            compatible = "gpio-keys";
>>>>>> +            #address-cells = <1>;
>>>>>> +            #size-cells = <0>;
>>>>>
>>>>> Just want to understand why these properties are here?
>>>>> As these properties are for child dt node. But have not seen
>>>>> anyone is using here.
>>>>>
>>>>
>>>> That is how gpio_keys node entries are defined in other .dts files.
>>>
>>> I have gone through example for address-cells and size-cells in following link:
>>> http://devicetree.org/mediawiki/index.php?title=Device_Tree_Usage&stable=1#CPU_addressing
>>>
>>> which indicates that these fields are for child "reg".
>>> I think, here in child node there is no "reg". so there is no use
>>> of address-cells and size-cells propeties.
>>>
>>
>> Please check Documentation/devicetree/bindings/gpio/gpio_keys.txt
>>
>> And whether these properties are required or not, I will let device tree
>> experts to comment on that.
>>
>> As such, currently all node entries for gpio_keys use these properties.
> you can just verify by a simple test.
> delete the 2 lines. address-cells and size cells.
> this will have no affect.
> now with these 2 lines deleted lines add a dummy reg property with
> address and cell. dtb compiler will warn.
> So I think what manish reffered is right.
> There is also a reference of smdk4210 for kepads.

Right. Compilation is ok even after removing the address-cell and
size-cell properties.

But since this is used across all the instances, I would like to know
the view of the authors on this.

David, Dimitry,

Can you please let us know your opinion on this? If these properties are
not required, then we can remove them from the documentation and from
node entries in several other dts files.

>>
>> --
>> Tushar Behera
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel


-- 
Tushar Behera

[PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons

[Tomasz Figa]

Hi,

I'm wondering why Exynos5250 has not been migrated to use pinctrl yet.

Support for it in pinctrl-samsung driver has been already merged, but I 
don't see any pinctrl nodes in exynos5250.dtsi.

This is important because the legacy gpio-samsung support is going to be 
dropped, as it already happened in case of Exynos 4.

CC'ing Thomas Abraham as he might know something.

Best regards,
-- 
Tomasz Figa
Samsung Poland R&D Center
SW Solution Development, Linux Platform

On Thursday 07 of February 2013 10:45:25 Tushar Behera wrote:
> Added GPIO buttons DT node to Arndale board file.
> 
> Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
> ---
> This series is based on for-next branch of Kukjin Kim's tree
> and added on top of the below patch:
> https://patchwork.kernel.org/patch/2042451/
> ---
>  arch/arm/boot/dts/exynos5250-arndale.dts |   48
> ++++++++++++++++++++++++++++++ 1 files changed, 48 insertions(+), 0
> deletions(-)
> 
> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts
> b/arch/arm/boot/dts/exynos5250-arndale.dts index 63572f9..9ce40df
> 100644
> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
> @@ -119,4 +119,52 @@
>  	spi_2: spi at 12d40000 {
>  		status = "disabled";
>  	};
> +
> +	gpio_keys {
> +		compatible = "gpio-keys";
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		menu {
> +			label = "SW-TACT2";
> +			gpios = <&gpx1 4 0 0x10000 2>;
> +			linux,code = <139>;
> +			gpio-key,wakeup;
> +		};
> +
> +		home {
> +			label = "SW-TACT3";
> +			gpios = <&gpx1 5 0 0x10000 2>;
> +			linux,code = <102>;
> +			gpio-key,wakeup;
> +		};
> +
> +		up {
> +			label = "SW-TACT4";
> +			gpios = <&gpx1 6 0 0x10000 2>;
> +			linux,code = <103>;
> +			gpio-key,wakeup;
> +		};
> +
> +		down {
> +			label = "SW-TACT5";
> +			gpios = <&gpx1 7 0 0x10000 2>;
> +			linux,code = <108>;
> +			gpio-key,wakeup;
> +		};
> +
> +		back {
> +			label = "SW-TACT6";
> +			gpios = <&gpx2 0 0 0x10000 2>;
> +			linux,code = <158>;
> +			gpio-key,wakeup;
> +		};
> +
> +		wakeup {
> +			label = "SW-TACT7";
> +			gpios = <&gpx2 1 0 0x10000 2>;
> +			linux,code = <143>;
> +			gpio-key,wakeup;
> +		};
> +	};
>  };

[PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons

[Tomasz Figa]

On Thursday 07 of February 2013 15:10:27 Tushar Behera wrote:
> +CC: David Jander <david@protonic.nl>
> +CC: Dmitry Torokhov <dtor@mail.ru>
> 
> On 02/07/2013 01:13 PM, Girish KS wrote:
> >>>>>> +
> >>>>>> +    gpio_keys {
> >>>>>> +            compatible = "gpio-keys";
> >>>>>> +            #address-cells = <1>;
> >>>>>> +            #size-cells = <0>;
> >>>>> 
> >>>>> Just want to understand why these properties are here?
> >>>>> As these properties are for child dt node. But have not seen
> >>>>> anyone is using here.
> >>>> 
> >>>> That is how gpio_keys node entries are defined in other .dts files.
> >>> 
> >>> I have gone through example for address-cells and size-cells in
> >>> following link:
> >>> http://devicetree.org/mediawiki/index.php?title=Device_Tree_Usage&s
> >>> table=1#CPU_addressing
> >>> 
> >>> which indicates that these fields are for child "reg".
> >>> I think, here in child node there is no "reg". so there is no use
> >>> of address-cells and size-cells propeties.
> >> 
> >> Please check Documentation/devicetree/bindings/gpio/gpio_keys.txt
> >> 
> >> And whether these properties are required or not, I will let device
> >> tree experts to comment on that.
> >> 
> >> As such, currently all node entries for gpio_keys use these
> >> properties.
> > 
> > you can just verify by a simple test.
> > delete the 2 lines. address-cells and size cells.
> > this will have no affect.
> > now with these 2 lines deleted lines add a dummy reg property with
> > address and cell. dtb compiler will warn.
> > So I think what manish reffered is right.
> > There is also a reference of smdk4210 for kepads.
> 
> Right. Compilation is ok even after removing the address-cell and
> size-cell properties.
> 
> But since this is used across all the instances, I would like to know
> the view of the authors on this.
> 
> David, Dimitry,
> 
> Can you please let us know your opinion on this? If these properties are
> not required, then we can remove them from the documentation and from
> node entries in several other dts files.

The #address-cells and #size-cells are used only together with reg 
properties of sub nodes. They define how many cells in reg specifier are 
used for registers address and length.

So, if you have #address-cells = <1> and #size-cells = <0>, then your reg 
specifier will be simply <addr>. You can get more complex specifiers using 
more address cells and size cells, like:

#address-cells = <3>;
#size-cells = <1>;

subdev at 1,2,3 {
	reg = <1 2 3 0x1000>;
	/* ... */
};

If you don't intend to use reg property for child device addressing then 
you don't define #address-cells and #size-cells properties.

I think that the documentation of gpio_keys binding should be corrected 
and possibly also moved to bindings/input instead of bindings/gpio, as 
this directory is intended to be used for GPIO controllers, not GPIO 
consumers.

Best regards,
-- 
Tomasz Figa
Samsung Poland R&D Center
SW Solution Development, Linux Platform

[PATCH 2/5] ARM: dts: exynos5250-arndale: Add PMIC node entry

[amit daniel kachhap]

The V2 of this patch is posted with comments suggested by Anil and
some missing LDO's.

Thanks,
Amit Daniel

On Wed, Feb 6, 2013 at 9:56 PM, Tushar Behera <tushar.behera@linaro.org> wrote:
> On 02/07/2013 11:19 AM, Kumar, Anil wrote:
>> On Thu, Feb 07, 2013 at 10:45:26, Tushar Behera wrote:
>>> From: Amit Daniel Kachhap <amit.daniel@samsung.com>
>>>
>>> Added S5M8767 PMIC DT nodes to Arndale board.
>>>
>>> Signed-off-by: Amit Daniel Kachhap <amit.daniel@samsung.com>
>>> Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
>>> Signed-off-by: Tushar Behera <tushar.behera@linaro.org>
>>> ---
>>>  arch/arm/boot/dts/exynos5250-arndale.dts |  213 +++++++++++++++++++++++++++++-
>>>  1 files changed, 212 insertions(+), 1 deletions(-)
>>>
>>> diff --git a/arch/arm/boot/dts/exynos5250-arndale.dts b/arch/arm/boot/dts/exynos5250-arndale.dts
>>> index 9ce40df..b40a02f 100644
>>> --- a/arch/arm/boot/dts/exynos5250-arndale.dts
>>> +++ b/arch/arm/boot/dts/exynos5250-arndale.dts
>>> @@ -25,7 +25,218 @@
>>>      };
>>>
>>>      i2c at 12C60000 {
>>> -            status = "disabled";
>>> +            status = "okay";
>>
>> Is there any need to change status "okay" here as in dtsi file it is
>> by default okay ?
>>
>
> Right, there is no need for setting it as "okay" explicitly.
>
> --
> Tushar Behera
> --
> To unsubscribe from this list: send the line "unsubscribe linux-samsung-soc" in
> the body of a message to majordomo at vger.kernel.org
> More majordomo info at  http://vger.kernel.org/majordomo-info.html

[PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons

[Kukjin Kim]

Tomasz Figa wrote:
> 
> Hi,
> 
> I'm wondering why Exynos5250 has not been migrated to use pinctrl yet.
> 
> Support for it in pinctrl-samsung driver has been already merged, but I
> don't see any pinctrl nodes in exynos5250.dtsi.
> 
> This is important because the legacy gpio-samsung support is going to be
> dropped, as it already happened in case of Exynos 4.
> 
> CC'ing Thomas Abraham as he might know something.
> 
Tushar and all,

I agree with Tomasz's opinion to support pinctrl instead of gpio on exynos5250
stuff.

Please re-submit with using pinctrl is in samsung tree.

If any problems, please let us know.

Thanks.

- Kukjin

[PATCH 2/5] ARM: dts: exynos5250-arndale: Add PMIC node entry

[Kukjin Kim]

amit daniel kachhap wrote:
> 
> The V2 of this patch is posted with comments suggested by Anil and
> some missing LDO's.
> 
OK, I see.

- Kukjin

[PATCH 1/5] ARM: dts: exynos5250-arndale: Add node entry for gpio-buttons

[Tushar Behera]

On 03/11/2013 07:35 AM, Kukjin Kim wrote:
> Tomasz Figa wrote:
>>
>> Hi,
>>
>> I'm wondering why Exynos5250 has not been migrated to use pinctrl yet.
>>
>> Support for it in pinctrl-samsung driver has been already merged, but I
>> don't see any pinctrl nodes in exynos5250.dtsi.
>>
>> This is important because the legacy gpio-samsung support is going to be
>> dropped, as it already happened in case of Exynos 4.
>>
>> CC'ing Thomas Abraham as he might know something.
>>
> Tushar and all,
> 
> I agree with Tomasz's opinion to support pinctrl instead of gpio on exynos5250
> stuff.
> 
> Please re-submit with using pinctrl is in samsung tree.
> 

Ok. I will rebase the patchset on for-next branch and re-submit.


-- 
Tushar Behera