From: santosh.shilimkar@ti.com (Santosh Shilimkar)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH 00/14] Random LPAE-related patches
Date: Fri, 17 May 2013 23:53:56 +0530 [thread overview]
Message-ID: <519675BC.8010800@ti.com> (raw)
In-Reply-To: <1368810473-26070-1-git-send-email-will.deacon@arm.com>
On Friday 17 May 2013 10:37 PM, Will Deacon wrote:
> Hello,
>
> This is a collection of LPAE-related patches (mostly fixes) that have
> been kicking around for a while and I've been collecting in one place.
> There were some extra patches for bootmem, but they produced lots of
> warnings and need more thought, so they've not been included here.
>
> All comments welcome,
>
> Will
>
> Cyril Chemparathy (9):
> ARM: LPAE: use signed arithmetic for mask definitions
> ARM: LPAE: use phys_addr_t in switch_mm()
> ARM: LPAE: use 64-bit accessors for TTBR registers
> ARM: LPAE: factor out T1SZ and TTBR1 computations
> ARM: LPAE: accomodate >32-bit addresses for page table base
> ARM: mm: use physical addresses in highmem sanity checks
> ARM: fix type of PHYS_PFN_OFFSET to unsigned long
> ARM: mm: cleanup checks for membank overlap with vmalloc area
> ARM: mm: clean up membank size limit checks
>
> Vitaly Andrianov (3):
> ARM: LPAE: use phys_addr_t in alloc_init_pud()
> ARM: LPAE: use phys_addr_t in free_memmap()
> ARM: LPAE: use phys_addr_t for initrd location
>
> Will Deacon (2):
> ARM: lpae: fix definition of PTE_HWTABLE_PTRS
> ARM: elf: add new hwcap for identifying atomic ldrd/strd instructions
>
Thanks for picking up the patches. As off-list discussed, I have
tested these patches along with remainder bootmem related patches.
Feel free to use,
Tested-by: Santosh Shilimkar <santosh.shilimkar@ti.com>
next prev parent reply other threads:[~2013-05-17 18:23 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2013-05-17 17:07 [PATCH 00/14] Random LPAE-related patches Will Deacon
2013-05-17 17:07 ` [PATCH 01/14] ARM: LPAE: use signed arithmetic for mask definitions Will Deacon
2013-05-17 17:07 ` [PATCH 02/14] ARM: LPAE: use phys_addr_t in alloc_init_pud() Will Deacon
2013-05-17 17:07 ` [PATCH 03/14] ARM: LPAE: use phys_addr_t in free_memmap() Will Deacon
2013-05-17 17:07 ` [PATCH 04/14] ARM: LPAE: use phys_addr_t for initrd location Will Deacon
2013-05-17 17:07 ` [PATCH 05/14] ARM: LPAE: use phys_addr_t in switch_mm() Will Deacon
2013-05-17 17:07 ` [PATCH 06/14] ARM: LPAE: use 64-bit accessors for TTBR registers Will Deacon
2013-05-17 17:07 ` [PATCH 07/14] ARM: LPAE: factor out T1SZ and TTBR1 computations Will Deacon
2013-05-17 17:07 ` [PATCH 08/14] ARM: LPAE: accomodate >32-bit addresses for page table base Will Deacon
2013-05-17 17:07 ` [PATCH 09/14] ARM: mm: use physical addresses in highmem sanity checks Will Deacon
2013-05-17 17:07 ` [PATCH 10/14] ARM: fix type of PHYS_PFN_OFFSET to unsigned long Will Deacon
2013-05-17 17:07 ` [PATCH 11/14] ARM: mm: cleanup checks for membank overlap with vmalloc area Will Deacon
2013-05-17 17:07 ` [PATCH 12/14] ARM: mm: clean up membank size limit checks Will Deacon
2013-05-17 17:07 ` [PATCH 13/14] ARM: lpae: fix definition of PTE_HWTABLE_PTRS Will Deacon
2013-05-17 17:07 ` [PATCH 14/14] ARM: elf: add new hwcap for identifying atomic ldrd/strd instructions Will Deacon
2013-05-20 14:18 ` Catalin Marinas
2013-05-20 14:24 ` Will Deacon
2013-05-20 15:11 ` Catalin Marinas
2013-05-20 16:04 ` Will Deacon
2013-05-20 17:13 ` Catalin Marinas
2013-05-21 18:02 ` Will Deacon
2013-05-22 8:43 ` Catalin Marinas
2013-05-21 18:48 ` Rob Herring
2013-05-22 8:47 ` Catalin Marinas
2013-05-22 18:09 ` Will Deacon
2013-05-23 8:50 ` Catalin Marinas
2013-05-17 18:23 ` Santosh Shilimkar [this message]
2013-05-30 13:31 ` [PATCH 00/14] Random LPAE-related patches Subash Patel
2013-05-30 15:03 ` Will Deacon
2013-05-31 0:38 ` Kukjin Kim
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=519675BC.8010800@ti.com \
--to=santosh.shilimkar@ti.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).