* [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees
@ 2013-05-27 14:52 Florian Vaussard
2013-05-27 14:52 ` [PATCH v3 1/5] ARM: dts: OMAP2+: use #include for all " Florian Vaussard
` (5 more replies)
0 siblings, 6 replies; 10+ messages in thread
From: Florian Vaussard @ 2013-05-27 14:52 UTC (permalink / raw)
To: linux-arm-kernel
Hello,
Following a similar proposal by Stephen Warren for tegra [1], this series
makes use of the C preprocessor when compiling OMAP DT files, and
accomplishes some improvements to improve overall readability.
Patch 1 is a preparation for the rest of the series.
Patch 2 uses existing constants for GPIOs. Patch 3 does the same for
IRQs. Patch 4 creates a new header for OMAP's padmux, and patch 5 uses
it to simplify pinctrl DT.
As for v2, the .dtb files were diff-tested before and after
applying the series to guarantee identity for all targets.
Best regards,
Florian
>From v2:
- Address Tony's comments (standardize comments, remove OMAP_ prefix)
>From v1:
- Remove duplicated fix
- Remove OMAP_GPIO macro
- Add pinctrl constants
Florian Vaussard (5):
ARM: dts: OMAP2+: use #include for all device trees
ARM: dts: OMAP2+: use existing constants for GPIOs
ARM: dts: OMAP4/5: use existing constants for IRQs
ARM: dts: OMAP2+: header file for pinctrl constants
ARM: dts: OMAP2+: use pinctrl constants
arch/arm/boot/dts/omap2.dtsi | 5 +-
arch/arm/boot/dts/omap2420-h4.dts | 2 +-
arch/arm/boot/dts/omap2420.dtsi | 2 +-
arch/arm/boot/dts/omap2430.dtsi | 2 +-
arch/arm/boot/dts/omap3-beagle-xm.dts | 8 +-
arch/arm/boot/dts/omap3-beagle.dts | 34 ++++----
arch/arm/boot/dts/omap3-devkit8000.dts | 10 +-
arch/arm/boot/dts/omap3-evm.dts | 6 +-
arch/arm/boot/dts/omap3-igep.dtsi | 36 ++++----
arch/arm/boot/dts/omap3-igep0020.dts | 10 +-
arch/arm/boot/dts/omap3-igep0030.dts | 10 +-
arch/arm/boot/dts/omap3-overo.dtsi | 4 +-
arch/arm/boot/dts/omap3-tobi.dts | 4 +-
arch/arm/boot/dts/omap3.dtsi | 5 +-
arch/arm/boot/dts/omap3430-sdp.dts | 4 +-
arch/arm/boot/dts/omap34xx.dtsi | 2 +-
arch/arm/boot/dts/omap36xx.dtsi | 2 +-
arch/arm/boot/dts/omap4-panda-a4.dts | 10 +-
arch/arm/boot/dts/omap4-panda-common.dtsi | 66 ++++++++--------
arch/arm/boot/dts/omap4-panda-es.dts | 10 +-
arch/arm/boot/dts/omap4-panda.dts | 4 +-
arch/arm/boot/dts/omap4-sdp-es23plus.dts | 8 +-
arch/arm/boot/dts/omap4-sdp.dts | 122 ++++++++++++++--------------
arch/arm/boot/dts/omap4-var-som.dts | 8 +-
arch/arm/boot/dts/omap4.dtsi | 118 ++++++++++++++-------------
arch/arm/boot/dts/omap443x.dtsi | 2 +-
arch/arm/boot/dts/omap4460.dtsi | 6 +-
arch/arm/boot/dts/omap5-evm.dts | 92 +++++++++++-----------
arch/arm/boot/dts/omap5.dtsi | 126 +++++++++++++++--------------
include/dt-bindings/pinctrl/omap.h | 50 +++++++++++
30 files changed, 416 insertions(+), 352 deletions(-)
create mode 100644 include/dt-bindings/pinctrl/omap.h
--
1.7.5.4
^ permalink raw reply [flat|nested] 10+ messages in thread* [PATCH v3 1/5] ARM: dts: OMAP2+: use #include for all device trees 2013-05-27 14:52 [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees Florian Vaussard @ 2013-05-27 14:52 ` Florian Vaussard 2013-05-27 14:52 ` [PATCH v3 2/5] ARM: dts: OMAP2+: use existing constants for GPIOs Florian Vaussard ` (4 subsequent siblings) 5 siblings, 0 replies; 10+ messages in thread From: Florian Vaussard @ 2013-05-27 14:52 UTC (permalink / raw) To: linux-arm-kernel Replace /include/ by #include for OMAP2+ DT, in order to use the C pre-processor, making use of #define features possible. Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> --- arch/arm/boot/dts/omap2.dtsi | 2 +- arch/arm/boot/dts/omap2420-h4.dts | 2 +- arch/arm/boot/dts/omap2420.dtsi | 2 +- arch/arm/boot/dts/omap2430.dtsi | 2 +- arch/arm/boot/dts/omap3-beagle-xm.dts | 4 ++-- arch/arm/boot/dts/omap3-beagle.dts | 4 ++-- arch/arm/boot/dts/omap3-devkit8000.dts | 4 ++-- arch/arm/boot/dts/omap3-evm.dts | 4 ++-- arch/arm/boot/dts/omap3-igep.dtsi | 4 ++-- arch/arm/boot/dts/omap3-igep0020.dts | 2 +- arch/arm/boot/dts/omap3-igep0030.dts | 2 +- arch/arm/boot/dts/omap3-overo.dtsi | 4 ++-- arch/arm/boot/dts/omap3-tobi.dts | 2 +- arch/arm/boot/dts/omap3.dtsi | 2 +- arch/arm/boot/dts/omap3430-sdp.dts | 4 ++-- arch/arm/boot/dts/omap34xx.dtsi | 2 +- arch/arm/boot/dts/omap36xx.dtsi | 2 +- arch/arm/boot/dts/omap4-panda-a4.dts | 4 ++-- arch/arm/boot/dts/omap4-panda-common.dtsi | 4 ++-- arch/arm/boot/dts/omap4-panda-es.dts | 4 ++-- arch/arm/boot/dts/omap4-panda.dts | 4 ++-- arch/arm/boot/dts/omap4-sdp-es23plus.dts | 2 +- arch/arm/boot/dts/omap4-sdp.dts | 6 +++--- arch/arm/boot/dts/omap4-var-som.dts | 4 ++-- arch/arm/boot/dts/omap4.dtsi | 2 +- arch/arm/boot/dts/omap443x.dtsi | 2 +- arch/arm/boot/dts/omap4460.dtsi | 2 +- arch/arm/boot/dts/omap5-evm.dts | 4 ++-- arch/arm/boot/dts/omap5.dtsi | 2 +- 29 files changed, 44 insertions(+), 44 deletions(-) diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi index 37aa748..e6e4587 100644 --- a/arch/arm/boot/dts/omap2.dtsi +++ b/arch/arm/boot/dts/omap2.dtsi @@ -8,7 +8,7 @@ * kind, whether express or implied. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { compatible = "ti,omap2430", "ti,omap2420", "ti,omap2"; diff --git a/arch/arm/boot/dts/omap2420-h4.dts b/arch/arm/boot/dts/omap2420-h4.dts index 68282ee..224c08f 100644 --- a/arch/arm/boot/dts/omap2420-h4.dts +++ b/arch/arm/boot/dts/omap2420-h4.dts @@ -7,7 +7,7 @@ */ /dts-v1/; -/include/ "omap2420.dtsi" +#include "omap2420.dtsi" / { model = "TI OMAP2420 H4 board"; diff --git a/arch/arm/boot/dts/omap2420.dtsi b/arch/arm/boot/dts/omap2420.dtsi index da5b285..c8f9c55 100644 --- a/arch/arm/boot/dts/omap2420.dtsi +++ b/arch/arm/boot/dts/omap2420.dtsi @@ -8,7 +8,7 @@ * kind, whether express or implied. */ -/include/ "omap2.dtsi" +#include "omap2.dtsi" / { compatible = "ti,omap2420", "ti,omap2"; diff --git a/arch/arm/boot/dts/omap2430.dtsi b/arch/arm/boot/dts/omap2430.dtsi index 054bc44..c535a5a 100644 --- a/arch/arm/boot/dts/omap2430.dtsi +++ b/arch/arm/boot/dts/omap2430.dtsi @@ -8,7 +8,7 @@ * kind, whether express or implied. */ -/include/ "omap2.dtsi" +#include "omap2.dtsi" / { compatible = "ti,omap2430", "ti,omap2"; diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index 3046d1f..e0ce823 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -7,7 +7,7 @@ */ /dts-v1/; -/include/ "omap36xx.dtsi" +#include "omap36xx.dtsi" / { model = "TI OMAP3 BeagleBoard xM"; @@ -75,7 +75,7 @@ }; }; -/include/ "twl4030.dtsi" +#include "twl4030.dtsi" &i2c2 { clock-frequency = <400000>; diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index 6eec699..fcac96a 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -7,7 +7,7 @@ */ /dts-v1/; -/include/ "omap34xx.dtsi" +#include "omap34xx.dtsi" / { model = "TI OMAP3 BeagleBoard"; @@ -107,7 +107,7 @@ }; }; -/include/ "twl4030.dtsi" +#include "twl4030.dtsi" &mmc1 { vmmc-supply = <&vmmc1>; diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts b/arch/arm/boot/dts/omap3-devkit8000.dts index 8a5cdcc..8d0f5e4 100644 --- a/arch/arm/boot/dts/omap3-devkit8000.dts +++ b/arch/arm/boot/dts/omap3-devkit8000.dts @@ -7,7 +7,7 @@ */ /dts-v1/; -/include/ "omap34xx.dtsi" +#include "omap34xx.dtsi" / { model = "TimLL OMAP3 Devkit8000"; compatible = "timll,omap3-devkit8000", "ti,omap3"; @@ -80,7 +80,7 @@ status = "disabled"; }; -/include/ "twl4030.dtsi" +#include "twl4030.dtsi" &mmc1 { vmmc-supply = <&vmmc1>; diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/omap3-evm.dts index 96d1c20..d75759b 100644 --- a/arch/arm/boot/dts/omap3-evm.dts +++ b/arch/arm/boot/dts/omap3-evm.dts @@ -7,7 +7,7 @@ */ /dts-v1/; -/include/ "omap34xx.dtsi" +#include "omap34xx.dtsi" / { model = "TI OMAP3 EVM (OMAP3530, AM/DM37x)"; @@ -44,7 +44,7 @@ }; }; -/include/ "twl4030.dtsi" +#include "twl4030.dtsi" &i2c2 { clock-frequency = <400000>; diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index f8fe3b7..54588b0 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -10,7 +10,7 @@ */ /dts-v1/; -/include/ "omap34xx.dtsi" +#include "omap34xx.dtsi" / { memory { @@ -80,7 +80,7 @@ }; }; -/include/ "twl4030.dtsi" +#include "twl4030.dtsi" &i2c2 { clock-frequency = <400000>; diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts index e2b9849..2f96a5c 100644 --- a/arch/arm/boot/dts/omap3-igep0020.dts +++ b/arch/arm/boot/dts/omap3-igep0020.dts @@ -9,7 +9,7 @@ * published by the Free Software Foundation. */ -/include/ "omap3-igep.dtsi" +#include "omap3-igep.dtsi" / { model = "IGEPv2"; diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts index 9dc48d2..f3a1bf0 100644 --- a/arch/arm/boot/dts/omap3-igep0030.dts +++ b/arch/arm/boot/dts/omap3-igep0030.dts @@ -9,7 +9,7 @@ * published by the Free Software Foundation. */ -/include/ "omap3-igep.dtsi" +#include "omap3-igep.dtsi" / { model = "IGEP COM Module"; diff --git a/arch/arm/boot/dts/omap3-overo.dtsi b/arch/arm/boot/dts/omap3-overo.dtsi index a626c50..e112a42 100644 --- a/arch/arm/boot/dts/omap3-overo.dtsi +++ b/arch/arm/boot/dts/omap3-overo.dtsi @@ -11,7 +11,7 @@ */ /dts-v1/; -/include/ "omap34xx.dtsi" +#include "omap34xx.dtsi" / { pwmleds { @@ -49,7 +49,7 @@ }; }; -/include/ "twl4030.dtsi" +#include "twl4030.dtsi" /* i2c2 pins are used for gpio */ &i2c2 { diff --git a/arch/arm/boot/dts/omap3-tobi.dts b/arch/arm/boot/dts/omap3-tobi.dts index a13d12d..5df894f 100644 --- a/arch/arm/boot/dts/omap3-tobi.dts +++ b/arch/arm/boot/dts/omap3-tobi.dts @@ -10,7 +10,7 @@ * Tobi expansion board is manufactured by Gumstix Inc. */ -/include/ "omap3-overo.dtsi" +#include "omap3-overo.dtsi" / { model = "TI OMAP3 Gumstix Overo on Tobi"; diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index 82a404d..7c7d494 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -8,7 +8,7 @@ * kind, whether express or implied. */ -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { compatible = "ti,omap3430", "ti,omap3"; diff --git a/arch/arm/boot/dts/omap3430-sdp.dts b/arch/arm/boot/dts/omap3430-sdp.dts index 144ae43..2a725a0 100644 --- a/arch/arm/boot/dts/omap3430-sdp.dts +++ b/arch/arm/boot/dts/omap3430-sdp.dts @@ -7,7 +7,7 @@ */ /dts-v1/; -/include/ "omap34xx.dtsi" +#include "omap34xx.dtsi" / { model = "TI OMAP3430 SDP"; @@ -28,7 +28,7 @@ }; }; -/include/ "twl4030.dtsi" +#include "twl4030.dtsi" &mmc1 { vmmc-supply = <&vmmc1>; diff --git a/arch/arm/boot/dts/omap34xx.dtsi b/arch/arm/boot/dts/omap34xx.dtsi index 75ed4ae..5355d61 100644 --- a/arch/arm/boot/dts/omap34xx.dtsi +++ b/arch/arm/boot/dts/omap34xx.dtsi @@ -8,7 +8,7 @@ * kind, whether express or implied. */ -/include/ "omap3.dtsi" +#include "omap3.dtsi" / { cpus { diff --git a/arch/arm/boot/dts/omap36xx.dtsi b/arch/arm/boot/dts/omap36xx.dtsi index f3447bc..f8b3765 100644 --- a/arch/arm/boot/dts/omap36xx.dtsi +++ b/arch/arm/boot/dts/omap36xx.dtsi @@ -8,7 +8,7 @@ * kind, whether express or implied. */ -/include/ "omap3.dtsi" +#include "omap3.dtsi" / { aliases { diff --git a/arch/arm/boot/dts/omap4-panda-a4.dts b/arch/arm/boot/dts/omap4-panda-a4.dts index e30cdf0..f18fb5c 100644 --- a/arch/arm/boot/dts/omap4-panda-a4.dts +++ b/arch/arm/boot/dts/omap4-panda-a4.dts @@ -7,8 +7,8 @@ */ /dts-v1/; -/include/ "omap443x.dtsi" -/include/ "omap4-panda-common.dtsi" +#include "omap443x.dtsi" +#include "omap4-panda-common.dtsi" /* Pandaboard Rev A4+ have external pullups on SCL & SDA */ &dss_hdmi_pins { diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 03bd60d..63148d1 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -5,7 +5,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ -/include/ "elpida_ecb240abacn.dtsi" +#include "elpida_ecb240abacn.dtsi" / { model = "TI OMAP4 PandaBoard"; @@ -164,7 +164,7 @@ }; }; -/include/ "twl6030.dtsi" +#include "twl6030.dtsi" &i2c2 { pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts index f1d8c21..c6f012e 100644 --- a/arch/arm/boot/dts/omap4-panda-es.dts +++ b/arch/arm/boot/dts/omap4-panda-es.dts @@ -7,8 +7,8 @@ */ /dts-v1/; -/include/ "omap4460.dtsi" -/include/ "omap4-panda-common.dtsi" +#include "omap4460.dtsi" +#include "omap4-panda-common.dtsi" /* Audio routing is differnet between PandaBoard4430 and PandaBoardES */ &sound { diff --git a/arch/arm/boot/dts/omap4-panda.dts b/arch/arm/boot/dts/omap4-panda.dts index f8b221f..6189a8b 100644 --- a/arch/arm/boot/dts/omap4-panda.dts +++ b/arch/arm/boot/dts/omap4-panda.dts @@ -7,5 +7,5 @@ */ /dts-v1/; -/include/ "omap443x.dtsi" -/include/ "omap4-panda-common.dtsi" +#include "omap443x.dtsi" +#include "omap4-panda-common.dtsi" diff --git a/arch/arm/boot/dts/omap4-sdp-es23plus.dts b/arch/arm/boot/dts/omap4-sdp-es23plus.dts index b4a40ff..4f26355 100644 --- a/arch/arm/boot/dts/omap4-sdp-es23plus.dts +++ b/arch/arm/boot/dts/omap4-sdp-es23plus.dts @@ -5,7 +5,7 @@ * it under the terms of the GNU General Public License version 2 as * published by the Free Software Foundation. */ -/include/ "omap4-sdp.dts" +#include "omap4-sdp.dts" /* SDP boards with 4430 ES2.3+ or 4460 have external pullups on SCL & SDA */ &dss_hdmi_pins { diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index a35d9cd..5edd08e 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -7,8 +7,8 @@ */ /dts-v1/; -/include/ "omap443x.dtsi" -/include/ "elpida_ecb240abacn.dtsi" +#include "omap443x.dtsi" +#include "elpida_ecb240abacn.dtsi" / { model = "TI OMAP4 SDP board"; @@ -316,7 +316,7 @@ }; }; -/include/ "twl6030.dtsi" +#include "twl6030.dtsi" &i2c2 { pinctrl-names = "default"; diff --git a/arch/arm/boot/dts/omap4-var-som.dts b/arch/arm/boot/dts/omap4-var-som.dts index 7e04103..6593607 100644 --- a/arch/arm/boot/dts/omap4-var-som.dts +++ b/arch/arm/boot/dts/omap4-var-som.dts @@ -7,7 +7,7 @@ */ /dts-v1/; -/include/ "omap443x.dtsi" +#include "omap443x.dtsi" / { model = "Variscite OMAP4 SOM"; @@ -39,7 +39,7 @@ }; }; -/include/ "twl6030.dtsi" +#include "twl6030.dtsi" &i2c2 { clock-frequency = <400000>; diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 2a56428..53d80aa 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -14,7 +14,7 @@ */ /memreserve/ 0x9d000000 0x03000000; -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { compatible = "ti,omap4430", "ti,omap4"; diff --git a/arch/arm/boot/dts/omap443x.dtsi b/arch/arm/boot/dts/omap443x.dtsi index cccf39a..a81f8df 100644 --- a/arch/arm/boot/dts/omap443x.dtsi +++ b/arch/arm/boot/dts/omap443x.dtsi @@ -8,7 +8,7 @@ * kind, whether express or implied. */ -/include/ "omap4.dtsi" +#include "omap4.dtsi" / { cpus { diff --git a/arch/arm/boot/dts/omap4460.dtsi b/arch/arm/boot/dts/omap4460.dtsi index 2cf227c..41762c2 100644 --- a/arch/arm/boot/dts/omap4460.dtsi +++ b/arch/arm/boot/dts/omap4460.dtsi @@ -7,7 +7,7 @@ * version 2. This program is licensed "as is" without any warranty of any * kind, whether express or implied. */ -/include/ "omap4.dtsi" +#include "omap4.dtsi" / { cpus { diff --git a/arch/arm/boot/dts/omap5-evm.dts b/arch/arm/boot/dts/omap5-evm.dts index 982acd1..f5f55d1 100644 --- a/arch/arm/boot/dts/omap5-evm.dts +++ b/arch/arm/boot/dts/omap5-evm.dts @@ -7,8 +7,8 @@ */ /dts-v1/; -/include/ "omap5.dtsi" -/include/ "samsung_k3pe0e000b.dtsi" +#include "omap5.dtsi" +#include "samsung_k3pe0e000b.dtsi" / { model = "TI OMAP5 EVM board"; diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index 3dd7ff8..e8e6653 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -15,7 +15,7 @@ */ /memreserve/ 0x9d000000 0x03000000; -/include/ "skeleton.dtsi" +#include "skeleton.dtsi" / { #address-cells = <1>; -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v3 2/5] ARM: dts: OMAP2+: use existing constants for GPIOs 2013-05-27 14:52 [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees Florian Vaussard 2013-05-27 14:52 ` [PATCH v3 1/5] ARM: dts: OMAP2+: use #include for all " Florian Vaussard @ 2013-05-27 14:52 ` Florian Vaussard 2013-05-27 14:52 ` [PATCH v3 3/5] ARM: dts: OMAP4/5: use existing constants for IRQs Florian Vaussard ` (3 subsequent siblings) 5 siblings, 0 replies; 10+ messages in thread From: Florian Vaussard @ 2013-05-27 14:52 UTC (permalink / raw) To: linux-arm-kernel Use standard GPIO constants to enhance the readability of DT GPIOs. Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> --- arch/arm/boot/dts/omap2.dtsi | 2 ++ arch/arm/boot/dts/omap3-beagle-xm.dts | 4 ++-- arch/arm/boot/dts/omap3-beagle.dts | 6 +++--- arch/arm/boot/dts/omap3-devkit8000.dts | 6 +++--- arch/arm/boot/dts/omap3-evm.dts | 2 +- arch/arm/boot/dts/omap3-igep0020.dts | 8 ++++---- arch/arm/boot/dts/omap3-igep0030.dts | 8 ++++---- arch/arm/boot/dts/omap3-tobi.dts | 2 +- arch/arm/boot/dts/omap3.dtsi | 2 ++ arch/arm/boot/dts/omap4-panda-common.dtsi | 4 ++-- arch/arm/boot/dts/omap4-sdp.dts | 16 ++++++++-------- arch/arm/boot/dts/omap4.dtsi | 2 ++ arch/arm/boot/dts/omap5.dtsi | 2 ++ 13 files changed, 36 insertions(+), 28 deletions(-) diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi index e6e4587..f39b237 100644 --- a/arch/arm/boot/dts/omap2.dtsi +++ b/arch/arm/boot/dts/omap2.dtsi @@ -8,6 +8,8 @@ * kind, whether express or implied. */ +#include <dt-bindings/gpio/gpio.h> + #include "skeleton.dtsi" / { diff --git a/arch/arm/boot/dts/omap3-beagle-xm.dts b/arch/arm/boot/dts/omap3-beagle-xm.dts index e0ce823..1e580d9 100644 --- a/arch/arm/boot/dts/omap3-beagle-xm.dts +++ b/arch/arm/boot/dts/omap3-beagle-xm.dts @@ -29,13 +29,13 @@ heartbeat { label = "beagleboard::usr0"; - gpios = <&gpio5 22 0>; /* 150 -> D6 LED */ + gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; /* 150 -> D6 LED */ linux,default-trigger = "heartbeat"; }; mmc { label = "beagleboard::usr1"; - gpios = <&gpio5 21 0>; /* 149 -> D7 LED */ + gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>; /* 149 -> D7 LED */ linux,default-trigger = "mmc0"; }; }; diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index fcac96a..434288f 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -28,18 +28,18 @@ compatible = "gpio-leds"; pmu_stat { label = "beagleboard::pmu_stat"; - gpios = <&twl_gpio 19 0>; /* LEDB */ + gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */ }; heartbeat { label = "beagleboard::usr0"; - gpios = <&gpio5 22 0>; /* 150 -> D6 LED */ + gpios = <&gpio5 22 GPIO_ACTIVE_HIGH>; /* 150 -> D6 LED */ linux,default-trigger = "heartbeat"; }; mmc { label = "beagleboard::usr1"; - gpios = <&gpio5 21 0>; /* 149 -> D7 LED */ + gpios = <&gpio5 21 GPIO_ACTIVE_HIGH>; /* 149 -> D7 LED */ linux,default-trigger = "mmc0"; }; }; diff --git a/arch/arm/boot/dts/omap3-devkit8000.dts b/arch/arm/boot/dts/omap3-devkit8000.dts index 8d0f5e4..5be71b1 100644 --- a/arch/arm/boot/dts/omap3-devkit8000.dts +++ b/arch/arm/boot/dts/omap3-devkit8000.dts @@ -22,21 +22,21 @@ heartbeat { label = "devkit8000::led1"; - gpios = <&gpio6 26 0>; /* 186 -> LED1 */ + gpios = <&gpio6 26 GPIO_ACTIVE_HIGH>; /* 186 -> LED1 */ default-state = "on"; linux,default-trigger = "heartbeat"; }; mmc { label = "devkit8000::led2"; - gpios = <&gpio6 3 0>; /* 163 -> LED2 */ + gpios = <&gpio6 3 GPIO_ACTIVE_HIGH>; /* 163 -> LED2 */ default-state = "on"; linux,default-trigger = "none"; }; usr { label = "devkit8000::led3"; - gpios = <&gpio6 4 0>; /* 164 -> LED3 */ + gpios = <&gpio6 4 GPIO_ACTIVE_HIGH>; /* 164 -> LED3 */ default-state = "on"; linux,default-trigger = "usr"; }; diff --git a/arch/arm/boot/dts/omap3-evm.dts b/arch/arm/boot/dts/omap3-evm.dts index d75759b..baa24bb 100644 --- a/arch/arm/boot/dts/omap3-evm.dts +++ b/arch/arm/boot/dts/omap3-evm.dts @@ -28,7 +28,7 @@ compatible = "gpio-leds"; ledb { label = "omap3evm::ledb"; - gpios = <&twl_gpio 19 0>; /* LEDB */ + gpios = <&twl_gpio 19 GPIO_ACTIVE_HIGH>; /* LEDB */ linux,default-trigger = "default-on"; }; }; diff --git a/arch/arm/boot/dts/omap3-igep0020.dts b/arch/arm/boot/dts/omap3-igep0020.dts index 2f96a5c..659e57c 100644 --- a/arch/arm/boot/dts/omap3-igep0020.dts +++ b/arch/arm/boot/dts/omap3-igep0020.dts @@ -19,25 +19,25 @@ compatible = "gpio-leds"; boot { label = "omap3:green:boot"; - gpios = <&gpio1 26 0>; + gpios = <&gpio1 26 GPIO_ACTIVE_HIGH>; default-state = "on"; }; user0 { label = "omap3:red:user0"; - gpios = <&gpio1 27 0>; + gpios = <&gpio1 27 GPIO_ACTIVE_HIGH>; default-state = "off"; }; user1 { label = "omap3:red:user1"; - gpios = <&gpio1 28 0>; + gpios = <&gpio1 28 GPIO_ACTIVE_HIGH>; default-state = "off"; }; user2 { label = "omap3:green:user1"; - gpios = <&twl_gpio 19 1>; + gpios = <&twl_gpio 19 GPIO_ACTIVE_LOW>; }; }; }; diff --git a/arch/arm/boot/dts/omap3-igep0030.dts b/arch/arm/boot/dts/omap3-igep0030.dts index f3a1bf0..8d3baef 100644 --- a/arch/arm/boot/dts/omap3-igep0030.dts +++ b/arch/arm/boot/dts/omap3-igep0030.dts @@ -19,25 +19,25 @@ compatible = "gpio-leds"; boot { label = "omap3:green:boot"; - gpios = <&twl_gpio 13 1>; + gpios = <&twl_gpio 13 GPIO_ACTIVE_LOW>; default-state = "on"; }; user0 { label = "omap3:red:user0"; - gpios = <&twl_gpio 18 1>; /* LEDA */ + gpios = <&twl_gpio 18 GPIO_ACTIVE_LOW>; /* LEDA */ default-state = "off"; }; user1 { label = "omap3:green:user1"; - gpios = <&twl_gpio 19 1>; /* LEDB */ + gpios = <&twl_gpio 19 GPIO_ACTIVE_LOW>; /* LEDB */ default-state = "off"; }; user2 { label = "omap3:red:user1"; - gpios = <&gpio1 16 1>; + gpios = <&gpio1 16 GPIO_ACTIVE_LOW>; default-state = "off"; }; }; diff --git a/arch/arm/boot/dts/omap3-tobi.dts b/arch/arm/boot/dts/omap3-tobi.dts index 5df894f..c7eebbf 100644 --- a/arch/arm/boot/dts/omap3-tobi.dts +++ b/arch/arm/boot/dts/omap3-tobi.dts @@ -20,7 +20,7 @@ compatible = "gpio-leds"; heartbeat { label = "overo:red:gpio21"; - gpios = <&gpio1 21 0>; + gpios = <&gpio1 21 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; }; diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index 7c7d494..aede64d 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -8,6 +8,8 @@ * kind, whether express or implied. */ +#include <dt-bindings/gpio/gpio.h> + #include "skeleton.dtsi" / { diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 63148d1..a3ef2bd 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -20,13 +20,13 @@ compatible = "gpio-leds"; heartbeat { label = "pandaboard::status1"; - gpios = <&gpio1 7 0>; + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; linux,default-trigger = "heartbeat"; }; mmc { label = "pandaboard::status2"; - gpios = <&gpio1 8 0>; + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; linux,default-trigger = "mmc0"; }; }; diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index 5edd08e..564d19b 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -41,42 +41,42 @@ compatible = "gpio-leds"; debug0 { label = "omap4:green:debug0"; - gpios = <&gpio2 29 0>; /* 61 */ + gpios = <&gpio2 29 GPIO_ACTIVE_HIGH>; /* 61 */ }; debug1 { label = "omap4:green:debug1"; - gpios = <&gpio1 30 0>; /* 30 */ + gpios = <&gpio1 30 GPIO_ACTIVE_HIGH>; /* 30 */ }; debug2 { label = "omap4:green:debug2"; - gpios = <&gpio1 7 0>; /* 7 */ + gpios = <&gpio1 7 GPIO_ACTIVE_HIGH>; /* 7 */ }; debug3 { label = "omap4:green:debug3"; - gpios = <&gpio1 8 0>; /* 8 */ + gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>; /* 8 */ }; debug4 { label = "omap4:green:debug4"; - gpios = <&gpio2 18 0>; /* 50 */ + gpios = <&gpio2 18 GPIO_ACTIVE_HIGH>; /* 50 */ }; user1 { label = "omap4:blue:user"; - gpios = <&gpio6 9 0>; /* 169 */ + gpios = <&gpio6 9 GPIO_ACTIVE_HIGH>; /* 169 */ }; user2 { label = "omap4:red:user"; - gpios = <&gpio6 10 0>; /* 170 */ + gpios = <&gpio6 10 GPIO_ACTIVE_HIGH>; /* 170 */ }; user3 { label = "omap4:green:user"; - gpios = <&gpio5 11 0>; /* 139 */ + gpios = <&gpio5 11 GPIO_ACTIVE_HIGH>; /* 139 */ }; }; diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 53d80aa..00f6ab9 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -14,6 +14,8 @@ */ /memreserve/ 0x9d000000 0x03000000; +#include <dt-bindings/gpio/gpio.h> + #include "skeleton.dtsi" / { diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index e8e6653..d613bf5 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -15,6 +15,8 @@ */ /memreserve/ 0x9d000000 0x03000000; +#include <dt-bindings/gpio/gpio.h> + #include "skeleton.dtsi" / { -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v3 3/5] ARM: dts: OMAP4/5: use existing constants for IRQs 2013-05-27 14:52 [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees Florian Vaussard 2013-05-27 14:52 ` [PATCH v3 1/5] ARM: dts: OMAP2+: use #include for all " Florian Vaussard 2013-05-27 14:52 ` [PATCH v3 2/5] ARM: dts: OMAP2+: use existing constants for GPIOs Florian Vaussard @ 2013-05-27 14:52 ` Florian Vaussard 2013-05-27 14:52 ` [PATCH v3 4/5] ARM: dts: OMAP2+: header file for pinctrl constants Florian Vaussard ` (2 subsequent siblings) 5 siblings, 0 replies; 10+ messages in thread From: Florian Vaussard @ 2013-05-27 14:52 UTC (permalink / raw) To: linux-arm-kernel Use the constants defined in include/dt-bindings/interrupt-controller/ to enhance readability. Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> --- arch/arm/boot/dts/omap4-panda-common.dtsi | 8 +- arch/arm/boot/dts/omap4-sdp.dts | 6 +- arch/arm/boot/dts/omap4-var-som.dts | 4 +- arch/arm/boot/dts/omap4.dtsi | 113 ++++++++++++++------------- arch/arm/boot/dts/omap4460.dtsi | 4 +- arch/arm/boot/dts/omap5.dtsi | 121 +++++++++++++++-------------- 6 files changed, 129 insertions(+), 127 deletions(-) diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index a3ef2bd..16b03fd 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -145,16 +145,16 @@ twl: twl at 48 { reg = <0x48>; - /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */ - interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */ + /* IRQ# = 7 */ + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */ interrupt-parent = <&gic>; }; twl6040: twl at 4b { compatible = "ti,twl6040"; reg = <0x4b>; - /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */ - interrupts = <0 119 4>; /* IRQ_SYS_2N cascaded to gic */ + /* IRQ# = 119 */ + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */ interrupt-parent = <&gic>; ti,audpwron-gpio = <&gpio4 31 0>; /* gpio line 127 */ diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index 564d19b..509e27c 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -286,7 +286,7 @@ twl: twl at 48 { reg = <0x48>; /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */ - interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */ + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */ interrupt-parent = <&gic>; }; @@ -294,7 +294,7 @@ compatible = "ti,twl6040"; reg = <0x4b>; /* SPI = 0, IRQ# = 119, 4 = active high level-sensitive */ - interrupts = <0 119 4>; /* IRQ_SYS_2N cascaded to gic */ + interrupts = <GIC_SPI 119 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_2N cascaded to gic */ interrupt-parent = <&gic>; ti,audpwron-gpio = <&gpio4 31 0>; /* gpio line 127 */ @@ -375,7 +375,7 @@ spi-max-frequency = <24000000>; reg = <0>; interrupt-parent = <&gpio2>; - interrupts = <2 8>; /* gpio line 34, low triggered */ + interrupts = <2 IRQ_TYPE_LEVEL_LOW>; /* gpio line 34, low triggered */ vdd-supply = <&vdd_eth>; }; }; diff --git a/arch/arm/boot/dts/omap4-var-som.dts b/arch/arm/boot/dts/omap4-var-som.dts index 6593607..135ba45 100644 --- a/arch/arm/boot/dts/omap4-var-som.dts +++ b/arch/arm/boot/dts/omap4-var-som.dts @@ -34,7 +34,7 @@ twl: twl at 48 { reg = <0x48>; /* SPI = 0, IRQ# = 7, 4 = active high level-sensitive */ - interrupts = <0 7 4>; /* IRQ_SYS_1N cascaded to gic */ + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>; /* IRQ_SYS_1N cascaded to gic */ interrupt-parent = <&gic>; }; }; @@ -68,7 +68,7 @@ spi-max-frequency = <24000000>; reg = <0>; interrupt-parent = <&gpio6>; - interrupts = <11 8>; /* gpio line 171, low triggered */ + interrupts = <11 IRQ_TYPE_LEVEL_LOW>; /* gpio line 171, low triggered */ vdd-supply = <&vdd_eth>; }; }; diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index 00f6ab9..d4304a2 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -15,6 +15,7 @@ /memreserve/ 0x9d000000 0x03000000; #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> #include "skeleton.dtsi" @@ -58,7 +59,7 @@ local-timer at 0x48240600 { compatible = "arm,cortex-a9-twd-timer"; reg = <0x48240600 0x20>; - interrupts = <1 13 0x304>; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_HIGH)>; }; /* @@ -99,8 +100,8 @@ reg = <0x44000000 0x1000>, <0x44800000 0x2000>, <0x45000000 0x1000>; - interrupts = <0 9 0x4>, - <0 10 0x4>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; counter32k: counter at 4a304000 { compatible = "ti,omap-counter32k"; @@ -128,10 +129,10 @@ sdma: dma-controller at 4a056000 { compatible = "ti,omap4430-sdma"; reg = <0x4a056000 0x1000>; - interrupts = <0 12 0x4>, - <0 13 0x4>, - <0 14 0x4>, - <0 15 0x4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; #dma-cells = <1>; #dma-channels = <32>; #dma-requests = <127>; @@ -140,7 +141,7 @@ gpio1: gpio at 4a310000 { compatible = "ti,omap4-gpio"; reg = <0x4a310000 0x200>; - interrupts = <0 29 0x4>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "gpio1"; ti,gpio-always-on; gpio-controller; @@ -152,7 +153,7 @@ gpio2: gpio at 48055000 { compatible = "ti,omap4-gpio"; reg = <0x48055000 0x200>; - interrupts = <0 30 0x4>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "gpio2"; gpio-controller; #gpio-cells = <2>; @@ -163,7 +164,7 @@ gpio3: gpio at 48057000 { compatible = "ti,omap4-gpio"; reg = <0x48057000 0x200>; - interrupts = <0 31 0x4>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "gpio3"; gpio-controller; #gpio-cells = <2>; @@ -174,7 +175,7 @@ gpio4: gpio at 48059000 { compatible = "ti,omap4-gpio"; reg = <0x48059000 0x200>; - interrupts = <0 32 0x4>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "gpio4"; gpio-controller; #gpio-cells = <2>; @@ -185,7 +186,7 @@ gpio5: gpio at 4805b000 { compatible = "ti,omap4-gpio"; reg = <0x4805b000 0x200>; - interrupts = <0 33 0x4>; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "gpio5"; gpio-controller; #gpio-cells = <2>; @@ -196,7 +197,7 @@ gpio6: gpio at 4805d000 { compatible = "ti,omap4-gpio"; reg = <0x4805d000 0x200>; - interrupts = <0 34 0x4>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "gpio6"; gpio-controller; #gpio-cells = <2>; @@ -209,7 +210,7 @@ reg = <0x50000000 0x1000>; #address-cells = <2>; #size-cells = <1>; - interrupts = <0 20 0x4>; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; gpmc,num-cs = <8>; gpmc,num-waitpins = <4>; ti,hwmods = "gpmc"; @@ -218,7 +219,7 @@ uart1: serial at 4806a000 { compatible = "ti,omap4-uart"; reg = <0x4806a000 0x100>; - interrupts = <0 72 0x4>; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "uart1"; clock-frequency = <48000000>; }; @@ -226,7 +227,7 @@ uart2: serial at 4806c000 { compatible = "ti,omap4-uart"; reg = <0x4806c000 0x100>; - interrupts = <0 73 0x4>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "uart2"; clock-frequency = <48000000>; }; @@ -234,7 +235,7 @@ uart3: serial at 48020000 { compatible = "ti,omap4-uart"; reg = <0x48020000 0x100>; - interrupts = <0 74 0x4>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "uart3"; clock-frequency = <48000000>; }; @@ -242,7 +243,7 @@ uart4: serial at 4806e000 { compatible = "ti,omap4-uart"; reg = <0x4806e000 0x100>; - interrupts = <0 70 0x4>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "uart4"; clock-frequency = <48000000>; }; @@ -250,7 +251,7 @@ i2c1: i2c at 48070000 { compatible = "ti,omap4-i2c"; reg = <0x48070000 0x100>; - interrupts = <0 56 0x4>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c1"; @@ -259,7 +260,7 @@ i2c2: i2c at 48072000 { compatible = "ti,omap4-i2c"; reg = <0x48072000 0x100>; - interrupts = <0 57 0x4>; + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c2"; @@ -268,7 +269,7 @@ i2c3: i2c at 48060000 { compatible = "ti,omap4-i2c"; reg = <0x48060000 0x100>; - interrupts = <0 61 0x4>; + interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c3"; @@ -277,7 +278,7 @@ i2c4: i2c at 48350000 { compatible = "ti,omap4-i2c"; reg = <0x48350000 0x100>; - interrupts = <0 62 0x4>; + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c4"; @@ -286,7 +287,7 @@ mcspi1: spi at 48098000 { compatible = "ti,omap4-mcspi"; reg = <0x48098000 0x200>; - interrupts = <0 65 0x4>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi1"; @@ -306,7 +307,7 @@ mcspi2: spi at 4809a000 { compatible = "ti,omap4-mcspi"; reg = <0x4809a000 0x200>; - interrupts = <0 66 0x4>; + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi2"; @@ -321,7 +322,7 @@ mcspi3: spi at 480b8000 { compatible = "ti,omap4-mcspi"; reg = <0x480b8000 0x200>; - interrupts = <0 91 0x4>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi3"; @@ -333,7 +334,7 @@ mcspi4: spi at 480ba000 { compatible = "ti,omap4-mcspi"; reg = <0x480ba000 0x200>; - interrupts = <0 48 0x4>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi4"; @@ -345,7 +346,7 @@ mmc1: mmc at 4809c000 { compatible = "ti,omap4-hsmmc"; reg = <0x4809c000 0x400>; - interrupts = <0 83 0x4>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mmc1"; ti,dual-volt; ti,needs-special-reset; @@ -356,7 +357,7 @@ mmc2: mmc at 480b4000 { compatible = "ti,omap4-hsmmc"; reg = <0x480b4000 0x400>; - interrupts = <0 86 0x4>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mmc2"; ti,needs-special-reset; dmas = <&sdma 47>, <&sdma 48>; @@ -366,7 +367,7 @@ mmc3: mmc at 480ad000 { compatible = "ti,omap4-hsmmc"; reg = <0x480ad000 0x400>; - interrupts = <0 94 0x4>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mmc3"; ti,needs-special-reset; dmas = <&sdma 77>, <&sdma 78>; @@ -376,7 +377,7 @@ mmc4: mmc at 480d1000 { compatible = "ti,omap4-hsmmc"; reg = <0x480d1000 0x400>; - interrupts = <0 96 0x4>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mmc4"; ti,needs-special-reset; dmas = <&sdma 57>, <&sdma 58>; @@ -386,7 +387,7 @@ mmc5: mmc at 480d5000 { compatible = "ti,omap4-hsmmc"; reg = <0x480d5000 0x400>; - interrupts = <0 59 0x4>; + interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mmc5"; ti,needs-special-reset; dmas = <&sdma 59>, <&sdma 60>; @@ -396,7 +397,7 @@ wdt2: wdt at 4a314000 { compatible = "ti,omap4-wdt", "ti,omap3-wdt"; reg = <0x4a314000 0x80>; - interrupts = <0 80 0x4>; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "wd_timer2"; }; @@ -405,7 +406,7 @@ reg = <0x40132000 0x7f>, /* MPU private access */ <0x49032000 0x7f>; /* L3 Interconnect */ reg-names = "mpu", "dma"; - interrupts = <0 112 0x4>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mcpdm"; dmas = <&sdma 65>, <&sdma 66>; @@ -417,7 +418,7 @@ reg = <0x4012e000 0x7f>, /* MPU private access */ <0x4902e000 0x7f>; /* L3 Interconnect */ reg-names = "mpu", "dma"; - interrupts = <0 114 0x4>; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "dmic"; dmas = <&sdma 67>; dma-names = "up_link"; @@ -428,7 +429,7 @@ reg = <0x40122000 0xff>, /* MPU private access */ <0x49022000 0xff>; /* L3 Interconnect */ reg-names = "mpu", "dma"; - interrupts = <0 17 0x4>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "common"; ti,buffer-size = <128>; ti,hwmods = "mcbsp1"; @@ -442,7 +443,7 @@ reg = <0x40124000 0xff>, /* MPU private access */ <0x49024000 0xff>; /* L3 Interconnect */ reg-names = "mpu", "dma"; - interrupts = <0 22 0x4>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "common"; ti,buffer-size = <128>; ti,hwmods = "mcbsp2"; @@ -456,7 +457,7 @@ reg = <0x40126000 0xff>, /* MPU private access */ <0x49026000 0xff>; /* L3 Interconnect */ reg-names = "mpu", "dma"; - interrupts = <0 23 0x4>; + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "common"; ti,buffer-size = <128>; ti,hwmods = "mcbsp3"; @@ -469,7 +470,7 @@ compatible = "ti,omap4-mcbsp"; reg = <0x48096000 0xff>; /* L4 Interconnect */ reg-names = "mpu"; - interrupts = <0 16 0x4>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "common"; ti,buffer-size = <128>; ti,hwmods = "mcbsp4"; @@ -481,7 +482,7 @@ keypad: keypad at 4a31c000 { compatible = "ti,omap4-keypad"; reg = <0x4a31c000 0x80>; - interrupts = <0 120 0x4>; + interrupts = <GIC_SPI 120 IRQ_TYPE_LEVEL_HIGH>; reg-names = "mpu"; ti,hwmods = "kbd"; }; @@ -489,7 +490,7 @@ emif1: emif at 4c000000 { compatible = "ti,emif-4d"; reg = <0x4c000000 0x100>; - interrupts = <0 110 0x4>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "emif1"; phy-type = <1>; hw-caps-read-idle-ctrl; @@ -500,7 +501,7 @@ emif2: emif at 4d000000 { compatible = "ti,emif-4d"; reg = <0x4d000000 0x100>; - interrupts = <0 111 0x4>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "emif2"; phy-type = <1>; hw-caps-read-idle-ctrl; @@ -525,7 +526,7 @@ timer1: timer at 4a318000 { compatible = "ti,omap3430-timer"; reg = <0x4a318000 0x80>; - interrupts = <0 37 0x4>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer1"; ti,timer-alwon; }; @@ -533,21 +534,21 @@ timer2: timer at 48032000 { compatible = "ti,omap3430-timer"; reg = <0x48032000 0x80>; - interrupts = <0 38 0x4>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer2"; }; timer3: timer at 48034000 { compatible = "ti,omap4430-timer"; reg = <0x48034000 0x80>; - interrupts = <0 39 0x4>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer3"; }; timer4: timer at 48036000 { compatible = "ti,omap4430-timer"; reg = <0x48036000 0x80>; - interrupts = <0 40 0x4>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer4"; }; @@ -555,7 +556,7 @@ compatible = "ti,omap4430-timer"; reg = <0x40138000 0x80>, <0x49038000 0x80>; - interrupts = <0 41 0x4>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer5"; ti,timer-dsp; }; @@ -564,7 +565,7 @@ compatible = "ti,omap4430-timer"; reg = <0x4013a000 0x80>, <0x4903a000 0x80>; - interrupts = <0 42 0x4>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer6"; ti,timer-dsp; }; @@ -573,7 +574,7 @@ compatible = "ti,omap4430-timer"; reg = <0x4013c000 0x80>, <0x4903c000 0x80>; - interrupts = <0 43 0x4>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer7"; ti,timer-dsp; }; @@ -582,7 +583,7 @@ compatible = "ti,omap4430-timer"; reg = <0x4013e000 0x80>, <0x4903e000 0x80>; - interrupts = <0 44 0x4>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer8"; ti,timer-pwm; ti,timer-dsp; @@ -591,7 +592,7 @@ timer9: timer at 4803e000 { compatible = "ti,omap4430-timer"; reg = <0x4803e000 0x80>; - interrupts = <0 45 0x4>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer9"; ti,timer-pwm; }; @@ -599,7 +600,7 @@ timer10: timer at 48086000 { compatible = "ti,omap3430-timer"; reg = <0x48086000 0x80>; - interrupts = <0 46 0x4>; + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer10"; ti,timer-pwm; }; @@ -607,7 +608,7 @@ timer11: timer at 48088000 { compatible = "ti,omap4430-timer"; reg = <0x48088000 0x80>; - interrupts = <0 47 0x4>; + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer11"; ti,timer-pwm; }; @@ -615,7 +616,7 @@ usbhstll: usbhstll at 4a062000 { compatible = "ti,usbhs-tll"; reg = <0x4a062000 0x1000>; - interrupts = <0 78 0x4>; + interrupts = <GIC_SPI 78 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "usb_tll_hs"; }; @@ -631,14 +632,14 @@ compatible = "ti,ohci-omap3", "usb-ohci"; reg = <0x4a064800 0x400>; interrupt-parent = <&gic>; - interrupts = <0 76 0x4>; + interrupts = <GIC_SPI 76 IRQ_TYPE_LEVEL_HIGH>; }; usbhsehci: ehci at 4a064c00 { compatible = "ti,ehci-omap", "usb-ehci"; reg = <0x4a064c00 0x400>; interrupt-parent = <&gic>; - interrupts = <0 77 0x4>; + interrupts = <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH>; }; }; @@ -653,7 +654,7 @@ usb_otg_hs: usb_otg_hs at 4a0ab000 { compatible = "ti,omap4-musb"; reg = <0x4a0ab000 0x7ff>; - interrupts = <0 92 0x4>, <0 93 0x4>; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>, <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "mc", "dma"; ti,hwmods = "usb_otg_hs"; usb-phy = <&usb2_phy>; diff --git a/arch/arm/boot/dts/omap4460.dtsi b/arch/arm/boot/dts/omap4460.dtsi index 41762c2..19628b1 100644 --- a/arch/arm/boot/dts/omap4460.dtsi +++ b/arch/arm/boot/dts/omap4460.dtsi @@ -25,8 +25,8 @@ pmu { compatible = "arm,cortex-a9-pmu"; - interrupts = <0 54 0x4>, - <0 55 0x4>; + interrupts = <GIC_SPI 54 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 55 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "debugss"; }; }; diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index d613bf5..061cf70 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -16,6 +16,7 @@ /memreserve/ 0x9d000000 0x03000000; #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> #include "skeleton.dtsi" @@ -47,10 +48,10 @@ timer { compatible = "arm,armv7-timer"; /* PPI secure/nonsecure IRQ, active low level-sensitive */ - interrupts = <1 13 0x308>, - <1 14 0x308>, - <1 11 0x308>, - <1 10 0x308>; + interrupts = <GIC_PPI 13 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 14 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 11 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>, + <GIC_PPI 10 (GIC_CPU_MASK_RAW(3) | IRQ_TYPE_LEVEL_LOW)>; clock-frequency = <6144000>; }; @@ -92,8 +93,8 @@ reg = <0x44000000 0x2000>, <0x44800000 0x3000>, <0x45000000 0x4000>; - interrupts = <0 9 0x4>, - <0 10 0x4>; + interrupts = <GIC_SPI 9 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 10 IRQ_TYPE_LEVEL_HIGH>; counter32k: counter at 4ae04000 { compatible = "ti,omap-counter32k"; @@ -121,10 +122,10 @@ sdma: dma-controller at 4a056000 { compatible = "ti,omap4430-sdma"; reg = <0x4a056000 0x1000>; - interrupts = <0 12 0x4>, - <0 13 0x4>, - <0 14 0x4>, - <0 15 0x4>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH>, + <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH>; #dma-cells = <1>; #dma-channels = <32>; #dma-requests = <127>; @@ -133,7 +134,7 @@ gpio1: gpio at 4ae10000 { compatible = "ti,omap4-gpio"; reg = <0x4ae10000 0x200>; - interrupts = <0 29 0x4>; + interrupts = <GIC_SPI 29 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "gpio1"; ti,gpio-always-on; gpio-controller; @@ -145,7 +146,7 @@ gpio2: gpio at 48055000 { compatible = "ti,omap4-gpio"; reg = <0x48055000 0x200>; - interrupts = <0 30 0x4>; + interrupts = <GIC_SPI 30 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "gpio2"; gpio-controller; #gpio-cells = <2>; @@ -156,7 +157,7 @@ gpio3: gpio at 48057000 { compatible = "ti,omap4-gpio"; reg = <0x48057000 0x200>; - interrupts = <0 31 0x4>; + interrupts = <GIC_SPI 31 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "gpio3"; gpio-controller; #gpio-cells = <2>; @@ -167,7 +168,7 @@ gpio4: gpio at 48059000 { compatible = "ti,omap4-gpio"; reg = <0x48059000 0x200>; - interrupts = <0 32 0x4>; + interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "gpio4"; gpio-controller; #gpio-cells = <2>; @@ -178,7 +179,7 @@ gpio5: gpio at 4805b000 { compatible = "ti,omap4-gpio"; reg = <0x4805b000 0x200>; - interrupts = <0 33 0x4>; + interrupts = <GIC_SPI 33 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "gpio5"; gpio-controller; #gpio-cells = <2>; @@ -189,7 +190,7 @@ gpio6: gpio at 4805d000 { compatible = "ti,omap4-gpio"; reg = <0x4805d000 0x200>; - interrupts = <0 34 0x4>; + interrupts = <GIC_SPI 34 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "gpio6"; gpio-controller; #gpio-cells = <2>; @@ -200,7 +201,7 @@ gpio7: gpio at 48051000 { compatible = "ti,omap4-gpio"; reg = <0x48051000 0x200>; - interrupts = <0 35 0x4>; + interrupts = <GIC_SPI 35 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "gpio7"; gpio-controller; #gpio-cells = <2>; @@ -211,7 +212,7 @@ gpio8: gpio at 48053000 { compatible = "ti,omap4-gpio"; reg = <0x48053000 0x200>; - interrupts = <0 121 0x4>; + interrupts = <GIC_SPI 121 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "gpio8"; gpio-controller; #gpio-cells = <2>; @@ -224,7 +225,7 @@ reg = <0x50000000 0x1000>; #address-cells = <2>; #size-cells = <1>; - interrupts = <0 20 0x4>; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH>; gpmc,num-cs = <8>; gpmc,num-waitpins = <4>; ti,hwmods = "gpmc"; @@ -233,7 +234,7 @@ i2c1: i2c at 48070000 { compatible = "ti,omap4-i2c"; reg = <0x48070000 0x100>; - interrupts = <0 56 0x4>; + interrupts = <GIC_SPI 56 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c1"; @@ -242,7 +243,7 @@ i2c2: i2c at 48072000 { compatible = "ti,omap4-i2c"; reg = <0x48072000 0x100>; - interrupts = <0 57 0x4>; + interrupts = <GIC_SPI 57 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c2"; @@ -251,7 +252,7 @@ i2c3: i2c at 48060000 { compatible = "ti,omap4-i2c"; reg = <0x48060000 0x100>; - interrupts = <0 61 0x4>; + interrupts = <GIC_SPI 61 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c3"; @@ -260,7 +261,7 @@ i2c4: i2c at 4807a000 { compatible = "ti,omap4-i2c"; reg = <0x4807a000 0x100>; - interrupts = <0 62 0x4>; + interrupts = <GIC_SPI 62 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c4"; @@ -269,7 +270,7 @@ i2c5: i2c at 4807c000 { compatible = "ti,omap4-i2c"; reg = <0x4807c000 0x100>; - interrupts = <0 60 0x4>; + interrupts = <GIC_SPI 60 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "i2c5"; @@ -278,7 +279,7 @@ mcspi1: spi at 48098000 { compatible = "ti,omap4-mcspi"; reg = <0x48098000 0x200>; - interrupts = <0 65 0x4>; + interrupts = <GIC_SPI 65 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi1"; @@ -298,7 +299,7 @@ mcspi2: spi at 4809a000 { compatible = "ti,omap4-mcspi"; reg = <0x4809a000 0x200>; - interrupts = <0 66 0x4>; + interrupts = <GIC_SPI 66 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi2"; @@ -313,7 +314,7 @@ mcspi3: spi at 480b8000 { compatible = "ti,omap4-mcspi"; reg = <0x480b8000 0x200>; - interrupts = <0 91 0x4>; + interrupts = <GIC_SPI 91 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi3"; @@ -325,7 +326,7 @@ mcspi4: spi at 480ba000 { compatible = "ti,omap4-mcspi"; reg = <0x480ba000 0x200>; - interrupts = <0 48 0x4>; + interrupts = <GIC_SPI 48 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <0>; ti,hwmods = "mcspi4"; @@ -337,7 +338,7 @@ uart1: serial at 4806a000 { compatible = "ti,omap4-uart"; reg = <0x4806a000 0x100>; - interrupts = <0 72 0x4>; + interrupts = <GIC_SPI 72 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "uart1"; clock-frequency = <48000000>; }; @@ -345,7 +346,7 @@ uart2: serial at 4806c000 { compatible = "ti,omap4-uart"; reg = <0x4806c000 0x100>; - interrupts = <0 73 0x4>; + interrupts = <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "uart2"; clock-frequency = <48000000>; }; @@ -353,7 +354,7 @@ uart3: serial at 48020000 { compatible = "ti,omap4-uart"; reg = <0x48020000 0x100>; - interrupts = <0 74 0x4>; + interrupts = <GIC_SPI 74 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "uart3"; clock-frequency = <48000000>; }; @@ -361,7 +362,7 @@ uart4: serial at 4806e000 { compatible = "ti,omap4-uart"; reg = <0x4806e000 0x100>; - interrupts = <0 70 0x4>; + interrupts = <GIC_SPI 70 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "uart4"; clock-frequency = <48000000>; }; @@ -369,7 +370,7 @@ uart5: serial at 48066000 { compatible = "ti,omap4-uart"; reg = <0x48066000 0x100>; - interrupts = <0 105 0x4>; + interrupts = <GIC_SPI 105 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "uart5"; clock-frequency = <48000000>; }; @@ -377,7 +378,7 @@ uart6: serial at 48068000 { compatible = "ti,omap4-uart"; reg = <0x48068000 0x100>; - interrupts = <0 106 0x4>; + interrupts = <GIC_SPI 106 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "uart6"; clock-frequency = <48000000>; }; @@ -385,7 +386,7 @@ mmc1: mmc at 4809c000 { compatible = "ti,omap4-hsmmc"; reg = <0x4809c000 0x400>; - interrupts = <0 83 0x4>; + interrupts = <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mmc1"; ti,dual-volt; ti,needs-special-reset; @@ -396,7 +397,7 @@ mmc2: mmc at 480b4000 { compatible = "ti,omap4-hsmmc"; reg = <0x480b4000 0x400>; - interrupts = <0 86 0x4>; + interrupts = <GIC_SPI 86 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mmc2"; ti,needs-special-reset; dmas = <&sdma 47>, <&sdma 48>; @@ -406,7 +407,7 @@ mmc3: mmc at 480ad000 { compatible = "ti,omap4-hsmmc"; reg = <0x480ad000 0x400>; - interrupts = <0 94 0x4>; + interrupts = <GIC_SPI 94 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mmc3"; ti,needs-special-reset; dmas = <&sdma 77>, <&sdma 78>; @@ -416,7 +417,7 @@ mmc4: mmc at 480d1000 { compatible = "ti,omap4-hsmmc"; reg = <0x480d1000 0x400>; - interrupts = <0 96 0x4>; + interrupts = <GIC_SPI 96 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mmc4"; ti,needs-special-reset; dmas = <&sdma 57>, <&sdma 58>; @@ -426,7 +427,7 @@ mmc5: mmc at 480d5000 { compatible = "ti,omap4-hsmmc"; reg = <0x480d5000 0x400>; - interrupts = <0 59 0x4>; + interrupts = <GIC_SPI 59 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mmc5"; ti,needs-special-reset; dmas = <&sdma 59>, <&sdma 60>; @@ -444,7 +445,7 @@ reg = <0x40132000 0x7f>, /* MPU private access */ <0x49032000 0x7f>; /* L3 Interconnect */ reg-names = "mpu", "dma"; - interrupts = <0 112 0x4>; + interrupts = <GIC_SPI 112 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "mcpdm"; dmas = <&sdma 65>, <&sdma 66>; @@ -456,7 +457,7 @@ reg = <0x4012e000 0x7f>, /* MPU private access */ <0x4902e000 0x7f>; /* L3 Interconnect */ reg-names = "mpu", "dma"; - interrupts = <0 114 0x4>; + interrupts = <GIC_SPI 114 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "dmic"; dmas = <&sdma 67>; dma-names = "up_link"; @@ -467,7 +468,7 @@ reg = <0x40122000 0xff>, /* MPU private access */ <0x49022000 0xff>; /* L3 Interconnect */ reg-names = "mpu", "dma"; - interrupts = <0 17 0x4>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "common"; ti,buffer-size = <128>; ti,hwmods = "mcbsp1"; @@ -481,7 +482,7 @@ reg = <0x40124000 0xff>, /* MPU private access */ <0x49024000 0xff>; /* L3 Interconnect */ reg-names = "mpu", "dma"; - interrupts = <0 22 0x4>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "common"; ti,buffer-size = <128>; ti,hwmods = "mcbsp2"; @@ -495,7 +496,7 @@ reg = <0x40126000 0xff>, /* MPU private access */ <0x49026000 0xff>; /* L3 Interconnect */ reg-names = "mpu", "dma"; - interrupts = <0 23 0x4>; + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH>; interrupt-names = "common"; ti,buffer-size = <128>; ti,hwmods = "mcbsp3"; @@ -507,7 +508,7 @@ timer1: timer at 4ae18000 { compatible = "ti,omap5430-timer"; reg = <0x4ae18000 0x80>; - interrupts = <0 37 0x4>; + interrupts = <GIC_SPI 37 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer1"; ti,timer-alwon; }; @@ -515,21 +516,21 @@ timer2: timer at 48032000 { compatible = "ti,omap5430-timer"; reg = <0x48032000 0x80>; - interrupts = <0 38 0x4>; + interrupts = <GIC_SPI 38 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer2"; }; timer3: timer at 48034000 { compatible = "ti,omap5430-timer"; reg = <0x48034000 0x80>; - interrupts = <0 39 0x4>; + interrupts = <GIC_SPI 39 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer3"; }; timer4: timer at 48036000 { compatible = "ti,omap5430-timer"; reg = <0x48036000 0x80>; - interrupts = <0 40 0x4>; + interrupts = <GIC_SPI 40 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer4"; }; @@ -537,7 +538,7 @@ compatible = "ti,omap5430-timer"; reg = <0x40138000 0x80>, <0x49038000 0x80>; - interrupts = <0 41 0x4>; + interrupts = <GIC_SPI 41 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer5"; ti,timer-dsp; }; @@ -546,7 +547,7 @@ compatible = "ti,omap5430-timer"; reg = <0x4013a000 0x80>, <0x4903a000 0x80>; - interrupts = <0 42 0x4>; + interrupts = <GIC_SPI 42 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer6"; ti,timer-dsp; ti,timer-pwm; @@ -556,7 +557,7 @@ compatible = "ti,omap5430-timer"; reg = <0x4013c000 0x80>, <0x4903c000 0x80>; - interrupts = <0 43 0x4>; + interrupts = <GIC_SPI 43 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer7"; ti,timer-dsp; }; @@ -565,7 +566,7 @@ compatible = "ti,omap5430-timer"; reg = <0x4013e000 0x80>, <0x4903e000 0x80>; - interrupts = <0 44 0x4>; + interrupts = <GIC_SPI 44 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer8"; ti,timer-dsp; ti,timer-pwm; @@ -574,21 +575,21 @@ timer9: timer at 4803e000 { compatible = "ti,omap5430-timer"; reg = <0x4803e000 0x80>; - interrupts = <0 45 0x4>; + interrupts = <GIC_SPI 45 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer9"; }; timer10: timer at 48086000 { compatible = "ti,omap5430-timer"; reg = <0x48086000 0x80>; - interrupts = <0 46 0x4>; + interrupts = <GIC_SPI 46 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer10"; }; timer11: timer at 48088000 { compatible = "ti,omap5430-timer"; reg = <0x48088000 0x80>; - interrupts = <0 47 0x4>; + interrupts = <GIC_SPI 47 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "timer11"; ti,timer-pwm; }; @@ -596,7 +597,7 @@ wdt2: wdt at 4ae14000 { compatible = "ti,omap5-wdt", "ti,omap3-wdt"; reg = <0x4ae14000 0x80>; - interrupts = <0 80 0x4>; + interrupts = <GIC_SPI 80 IRQ_TYPE_LEVEL_HIGH>; ti,hwmods = "wd_timer2"; }; @@ -605,7 +606,7 @@ ti,hwmods = "emif1"; phy-type = <2>; /* DDR PHY type: Intelli PHY */ reg = <0x4c000000 0x400>; - interrupts = <0 110 0x4>; + interrupts = <GIC_SPI 110 IRQ_TYPE_LEVEL_HIGH>; hw-caps-read-idle-ctrl; hw-caps-ll-interface; hw-caps-temp-alert; @@ -616,7 +617,7 @@ ti,hwmods = "emif2"; phy-type = <2>; /* DDR PHY type: Intelli PHY */ reg = <0x4d000000 0x400>; - interrupts = <0 111 0x4>; + interrupts = <GIC_SPI 111 IRQ_TYPE_LEVEL_HIGH>; hw-caps-read-idle-ctrl; hw-caps-ll-interface; hw-caps-temp-alert; @@ -634,7 +635,7 @@ compatible = "ti,dwc3"; ti,hwmods = "usb_otg_ss"; reg = <0x4a020000 0x1000>; - interrupts = <0 93 4>; + interrupts = <GIC_SPI 93 IRQ_TYPE_LEVEL_HIGH>; #address-cells = <1>; #size-cells = <1>; utmi-mode = <2>; @@ -642,7 +643,7 @@ dwc3 at 4a030000 { compatible = "synopsys,dwc3"; reg = <0x4a030000 0x1000>; - interrupts = <0 92 4>; + interrupts = <GIC_SPI 92 IRQ_TYPE_LEVEL_HIGH>; usb-phy = <&usb2_phy>, <&usb3_phy>; tx-fifo-resize; }; -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v3 4/5] ARM: dts: OMAP2+: header file for pinctrl constants 2013-05-27 14:52 [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees Florian Vaussard ` (2 preceding siblings ...) 2013-05-27 14:52 ` [PATCH v3 3/5] ARM: dts: OMAP4/5: use existing constants for IRQs Florian Vaussard @ 2013-05-27 14:52 ` Florian Vaussard 2013-05-27 14:52 ` [PATCH v3 5/5] ARM: dts: OMAP2+: use " Florian Vaussard 2013-05-28 8:41 ` [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees Florian Vaussard 5 siblings, 0 replies; 10+ messages in thread From: Florian Vaussard @ 2013-05-27 14:52 UTC (permalink / raw) To: linux-arm-kernel Most of the constants are taken from arch/arm/mach-omap2/mux.h. Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> --- include/dt-bindings/pinctrl/omap.h | 50 ++++++++++++++++++++++++++++++++++++ 1 files changed, 50 insertions(+), 0 deletions(-) create mode 100644 include/dt-bindings/pinctrl/omap.h diff --git a/include/dt-bindings/pinctrl/omap.h b/include/dt-bindings/pinctrl/omap.h new file mode 100644 index 0000000..370df3f --- /dev/null +++ b/include/dt-bindings/pinctrl/omap.h @@ -0,0 +1,50 @@ +/* + * This header provides constants for OMAP pinctrl bindings. + * + * Copyright (C) 2009 Nokia + * Copyright (C) 2009-2010 Texas Instruments + */ + +/* 34xx mux mode options for each pin. See TRM for options */ +#define MUX_MODE0 0 +#define MUX_MODE1 1 +#define MUX_MODE2 2 +#define MUX_MODE3 3 +#define MUX_MODE4 4 +#define MUX_MODE5 5 +#define MUX_MODE6 6 +#define MUX_MODE7 7 + +/* 24xx/34xx mux bit defines */ +#define PULL_ENA (1 << 3) +#define PULL_UP (1 << 4) +#define ALTELECTRICALSEL (1 << 5) + +/* 34xx specific mux bit defines */ +#define INPUT_EN (1 << 8) +#define OFF_EN (1 << 9) +#define OFFOUT_EN (1 << 10) +#define OFFOUT_VAL (1 << 11) +#define OFF_PULL_EN (1 << 12) +#define OFF_PULL_UP (1 << 13) +#define WAKEUP_EN (1 << 14) + +/* 44xx specific mux bit defines */ +#define WAKEUP_EVENT (1 << 15) + +/* Active pin states */ +#define PIN_OUTPUT 0 +#define PIN_OUTPUT_PULLUP (PIN_OUTPUT | PULL_ENA | PULL_UP) +#define PIN_OUTPUT_PULLDOWN (PIN_OUTPUT | PULL_ENA) +#define PIN_INPUT INPUT_EN +#define PIN_INPUT_PULLUP (PULL_ENA | INPUT_EN | PULL_UP) +#define PIN_INPUT_PULLDOWN (PULL_ENA | INPUT_EN) + +/* Off mode states */ +#define PIN_OFF_NONE 0 +#define PIN_OFF_OUTPUT_HIGH (OFF_EN | OFFOUT_EN | OFFOUT_VAL) +#define PIN_OFF_OUTPUT_LOW (OFF_EN | OFFOUT_EN) +#define PIN_OFF_INPUT_PULLUP (OFF_EN | OFF_PULL_EN | OFF_PULL_UP) +#define PIN_OFF_INPUT_PULLDOWN (OFF_EN | OFF_PULL_EN) +#define PIN_OFF_WAKEUPENABLE WAKEUP_EN + -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v3 5/5] ARM: dts: OMAP2+: use pinctrl constants 2013-05-27 14:52 [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees Florian Vaussard ` (3 preceding siblings ...) 2013-05-27 14:52 ` [PATCH v3 4/5] ARM: dts: OMAP2+: header file for pinctrl constants Florian Vaussard @ 2013-05-27 14:52 ` Florian Vaussard 2013-05-28 8:41 ` [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees Florian Vaussard 5 siblings, 0 replies; 10+ messages in thread From: Florian Vaussard @ 2013-05-27 14:52 UTC (permalink / raw) To: linux-arm-kernel Using constants for pinctrl allows a better readability, and remove redundancy with comments. Signed-off-by: Florian Vaussard <florian.vaussard@epfl.ch> Acked-by: Santosh Shilimkar <santosh.shilimkar@ti.com> --- arch/arm/boot/dts/omap2.dtsi | 1 + arch/arm/boot/dts/omap3-beagle.dts | 24 ++++---- arch/arm/boot/dts/omap3-igep.dtsi | 32 +++++----- arch/arm/boot/dts/omap3.dtsi | 1 + arch/arm/boot/dts/omap4-panda-a4.dts | 6 +- arch/arm/boot/dts/omap4-panda-common.dtsi | 50 ++++++++-------- arch/arm/boot/dts/omap4-panda-es.dts | 6 +- arch/arm/boot/dts/omap4-sdp-es23plus.dts | 6 +- arch/arm/boot/dts/omap4-sdp.dts | 94 ++++++++++++++-------------- arch/arm/boot/dts/omap4.dtsi | 1 + arch/arm/boot/dts/omap5-evm.dts | 88 +++++++++++++------------- arch/arm/boot/dts/omap5.dtsi | 1 + 12 files changed, 157 insertions(+), 153 deletions(-) diff --git a/arch/arm/boot/dts/omap2.dtsi b/arch/arm/boot/dts/omap2.dtsi index f39b237..b3cc896 100644 --- a/arch/arm/boot/dts/omap2.dtsi +++ b/arch/arm/boot/dts/omap2.dtsi @@ -9,6 +9,7 @@ */ #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/omap.h> #include "skeleton.dtsi" diff --git a/arch/arm/boot/dts/omap3-beagle.dts b/arch/arm/boot/dts/omap3-beagle.dts index 434288f..6d47c4b 100644 --- a/arch/arm/boot/dts/omap3-beagle.dts +++ b/arch/arm/boot/dts/omap3-beagle.dts @@ -81,18 +81,18 @@ hsusbb2_pins: pinmux_hsusbb2_pins { pinctrl-single,pins = < - 0x5c0 0x3 /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_clk OUTPUT */ - 0x5c2 0x3 /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_stp OUTPUT */ - 0x5c4 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dir INPUT | PULLDOWN */ - 0x5c6 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_nxt INPUT | PULLDOWN */ - 0x5c8 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat0 INPUT | PULLDOWN */ - 0x5cA 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat1 INPUT | PULLDOWN */ - 0x1a4 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat2 INPUT | PULLDOWN */ - 0x1a6 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat3 INPUT | PULLDOWN */ - 0x1a8 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat4 INPUT | PULLDOWN */ - 0x1aa 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat5 INPUT | PULLDOWN */ - 0x1ac 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat6 INPUT | PULLDOWN */ - 0x1ae 0x10b /* USBB2_ULPITLL_CLK_MUXMODE.usbb1_ulpiphy_dat7 INPUT | PULLDOWN */ + 0x5c0 (PIN_OUTPUT | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_clk */ + 0x5c2 (PIN_OUTPUT | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_stp */ + 0x5c4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dir */ + 0x5c6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_nxt */ + 0x5c8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat0 */ + 0x5cA (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat1 */ + 0x1a4 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat2 */ + 0x1a6 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat3 */ + 0x1a8 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat4 */ + 0x1aa (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat5 */ + 0x1ac (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat6 */ + 0x1ae (PIN_INPUT_PULLDOWN | MUX_MODE3) /* usbb2_ulpitll_clk.usbb1_ulpiphy_dat7 */ >; }; }; diff --git a/arch/arm/boot/dts/omap3-igep.dtsi b/arch/arm/boot/dts/omap3-igep.dtsi index 54588b0..7b62b80 100644 --- a/arch/arm/boot/dts/omap3-igep.dtsi +++ b/arch/arm/boot/dts/omap3-igep.dtsi @@ -29,37 +29,37 @@ &omap3_pmx_core { uart1_pins: pinmux_uart1_pins { pinctrl-single,pins = < - 0x152 0x100 /* uart1_rx.uart1_rx INPUT | MODE0 */ - 0x14c 0 /* uart1_tx.uart1_tx OUTPUT | MODE0 */ + 0x152 (PIN_INPUT | MUX_MODE0) /* uart1_rx.uart1_rx */ + 0x14c (PIN_OUTPUT |MUX_MODE0) /* uart1_tx.uart1_tx */ >; }; uart2_pins: pinmux_uart2_pins { pinctrl-single,pins = < - 0x14a 0x100 /* uart2_rx.uart2_rx INPUT | MODE0 */ - 0x148 0 /* uart2_tx.uart2_tx OUTPUT | MODE0 */ + 0x14a (PIN_INPUT | MUX_MODE0) /* uart2_rx.uart2_rx */ + 0x148 (PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ >; }; uart3_pins: pinmux_uart3_pins { pinctrl-single,pins = < - 0x16e 0x100 /* uart3_rx.uart3_rx INPUT | MODE0 */ - 0x170 0 /* uart3_tx.uart3_tx OUTPUT | MODE0 */ + 0x16e (PIN_INPUT | MUX_MODE0) /* uart3_rx.uart3_rx */ + 0x170 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx.uart3_tx */ >; }; mmc1_pins: pinmux_mmc1_pins { pinctrl-single,pins = < - 0x114 0x0118 /* sdmmc1_clk.sdmmc1_clk INPUT PULLUP | MODE 0 */ - 0x116 0x0118 /* sdmmc1_cmd.sdmmc1_cmd INPUT PULLUP | MODE 0 */ - 0x118 0x0118 /* sdmmc1_dat0.sdmmc1_dat0 INPUT PULLUP | MODE 0 */ - 0x11a 0x0118 /* sdmmc1_dat1.sdmmc1_dat1 INPUT PULLUP | MODE 0 */ - 0x11c 0x0118 /* sdmmc1_dat2.sdmmc1_dat2 INPUT PULLUP | MODE 0 */ - 0x11e 0x0118 /* sdmmc1_dat3.sdmmc1_dat3 INPUT PULLUP | MODE 0 */ - 0x120 0x0100 /* sdmmc1_dat4.sdmmc1_dat4 INPUT | MODE 0 */ - 0x122 0x0100 /* sdmmc1_dat5.sdmmc1_dat5 INPUT | MODE 0 */ - 0x124 0x0100 /* sdmmc1_dat6.sdmmc1_dat6 INPUT | MODE 0 */ - 0x126 0x0100 /* sdmmc1_dat7.sdmmc1_dat7 INPUT | MODE 0 */ + 0x114 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_clk.sdmmc1_clk */ + 0x116 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_cmd.sdmmc1_cmd */ + 0x118 (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat0.sdmmc1_dat0 */ + 0x11a (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat1.sdmmc1_dat1 */ + 0x11c (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat2.sdmmc1_dat2 */ + 0x11e (PIN_INPUT_PULLUP | MUX_MODE0) /* sdmmc1_dat3.sdmmc1_dat3 */ + 0x120 (PIN_INPUT | MUX_MODE0) /* sdmmc1_dat4.sdmmc1_dat4 */ + 0x122 (PIN_INPUT | MUX_MODE0) /* sdmmc1_dat5.sdmmc1_dat5 */ + 0x124 (PIN_INPUT | MUX_MODE0) /* sdmmc1_dat6.sdmmc1_dat6 */ + 0x126 (PIN_INPUT | MUX_MODE0) /* sdmmc1_dat7.sdmmc1_dat7 */ >; }; }; diff --git a/arch/arm/boot/dts/omap3.dtsi b/arch/arm/boot/dts/omap3.dtsi index aede64d..813370d 100644 --- a/arch/arm/boot/dts/omap3.dtsi +++ b/arch/arm/boot/dts/omap3.dtsi @@ -9,6 +9,7 @@ */ #include <dt-bindings/gpio/gpio.h> +#include <dt-bindings/pinctrl/omap.h> #include "skeleton.dtsi" diff --git a/arch/arm/boot/dts/omap4-panda-a4.dts b/arch/arm/boot/dts/omap4-panda-a4.dts index f18fb5c..133f1b7 100644 --- a/arch/arm/boot/dts/omap4-panda-a4.dts +++ b/arch/arm/boot/dts/omap4-panda-a4.dts @@ -13,8 +13,8 @@ /* Pandaboard Rev A4+ have external pullups on SCL & SDA */ &dss_hdmi_pins { pinctrl-single,pins = < - 0x5a 0x118 /* hdmi_cec.hdmi_cec INPUT PULLUP | MODE 0 */ - 0x5c 0x100 /* hdmi_scl.hdmi_scl INPUT | MODE 0 */ - 0x5e 0x100 /* hdmi_sda.hdmi_sda INPUT | MODE 0 */ + 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + 0x5c (PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */ + 0x5e (PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */ >; }; diff --git a/arch/arm/boot/dts/omap4-panda-common.dtsi b/arch/arm/boot/dts/omap4-panda-common.dtsi index 16b03fd..548329e 100644 --- a/arch/arm/boot/dts/omap4-panda-common.dtsi +++ b/arch/arm/boot/dts/omap4-panda-common.dtsi @@ -68,71 +68,71 @@ twl6040_pins: pinmux_twl6040_pins { pinctrl-single,pins = < - 0xe0 0x3 /* hdq_sio.gpio_127 OUTPUT | MODE3 */ - 0x160 0x100 /* sys_nirq2.sys_nirq2 INPUT | MODE0 */ + 0xe0 (PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */ + 0x160 (PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */ >; }; mcpdm_pins: pinmux_mcpdm_pins { pinctrl-single,pins = < - 0xc6 0x108 /* abe_pdm_ul_data.abe_pdm_ul_data INPUT PULLDOWN | MODE0 */ - 0xc8 0x108 /* abe_pdm_dl_data.abe_pdm_dl_data INPUT PULLDOWN | MODE0 */ - 0xca 0x118 /* abe_pdm_frame.abe_pdm_frame INPUT PULLUP | MODE0 */ - 0xcc 0x108 /* abe_pdm_lb_clk.abe_pdm_lb_clk INPUT PULLDOWN | MODE0 */ - 0xce 0x108 /* abe_clks.abe_clks INPUT PULLDOWN | MODE0 */ + 0xc6 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */ + 0xc8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */ + 0xca (PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */ + 0xcc (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */ + 0xce (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ >; }; mcbsp1_pins: pinmux_mcbsp1_pins { pinctrl-single,pins = < - 0xbe 0x100 /* abe_mcbsp1_clkx.abe_mcbsp1_clkx INPUT | MODE0 */ - 0xc0 0x108 /* abe_mcbsp1_dr.abe_mcbsp1_dr INPUT PULLDOWN | MODE0 */ - 0xc2 0x8 /* abe_mcbsp1_dx.abe_mcbsp1_dx OUTPUT PULLDOWN | MODE0 */ - 0xc4 0x100 /* abe_mcbsp1_fsx.abe_mcbsp1_fsx INPUT | MODE0 */ + 0xbe (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */ + 0xc0 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */ + 0xc2 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */ + 0xc4 (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */ >; }; dss_hdmi_pins: pinmux_dss_hdmi_pins { pinctrl-single,pins = < - 0x5a 0x118 /* hdmi_cec.hdmi_cec INPUT PULLUP | MODE 0 */ - 0x5c 0x118 /* hdmi_scl.hdmi_scl INPUT PULLUP | MODE 0 */ - 0x5e 0x118 /* hdmi_sda.hdmi_sda INPUT PULLUP | MODE 0 */ + 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + 0x5c (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */ + 0x5e (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */ >; }; tpd12s015_pins: pinmux_tpd12s015_pins { pinctrl-single,pins = < - 0x22 0x3 /* gpmc_a17.gpio_41 OUTPUT | MODE3 */ - 0x48 0x3 /* gpmc_nbe1.gpio_60 OUTPUT | MODE3 */ - 0x58 0x10b /* hdmi_hpd.gpio_63 INPUT PULLDOWN | MODE3 */ + 0x22 (PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */ + 0x48 (PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */ + 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */ >; }; i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < - 0xe2 0x118 /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */ - 0xe4 0x118 /* i2c1_sda PULLUP | INPUTENABLE | MODE0 */ + 0xe2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ + 0xe4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ >; }; i2c2_pins: pinmux_i2c2_pins { pinctrl-single,pins = < - 0xe6 0x118 /* i2c2_scl PULLUP | INPUTENABLE | MODE0 */ - 0xe8 0x118 /* i2c2_sda PULLUP | INPUTENABLE | MODE0 */ + 0xe6 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */ + 0xe8 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */ >; }; i2c3_pins: pinmux_i2c3_pins { pinctrl-single,pins = < - 0xea 0x118 /* i2c3_scl PULLUP | INPUTENABLE | MODE0 */ - 0xec 0x118 /* i2c3_sda PULLUP | INPUTENABLE | MODE0 */ + 0xea (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ + 0xec (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ >; }; i2c4_pins: pinmux_i2c4_pins { pinctrl-single,pins = < - 0xee 0x118 /* i2c4_scl PULLUP | INPUTENABLE | MODE0 */ - 0xf0 0x118 /* i2c4_sda PULLUP | INPUTENABLE | MODE0 */ + 0xee (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */ + 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */ >; }; }; diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts index c6f012e..5cfdf19 100644 --- a/arch/arm/boot/dts/omap4-panda-es.dts +++ b/arch/arm/boot/dts/omap4-panda-es.dts @@ -29,8 +29,8 @@ /* PandaboardES has external pullups on SCL & SDA */ &dss_hdmi_pins { pinctrl-single,pins = < - 0x5a 0x118 /* hdmi_cec.hdmi_cec INPUT PULLUP | MODE 0 */ - 0x5c 0x100 /* hdmi_scl.hdmi_scl INPUT | MODE 0 */ - 0x5e 0x100 /* hdmi_sda.hdmi_sda INPUT | MODE 0 */ + 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + 0x5c (PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */ + 0x5e (PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */ >; }; diff --git a/arch/arm/boot/dts/omap4-sdp-es23plus.dts b/arch/arm/boot/dts/omap4-sdp-es23plus.dts index 4f26355..aad5dda 100644 --- a/arch/arm/boot/dts/omap4-sdp-es23plus.dts +++ b/arch/arm/boot/dts/omap4-sdp-es23plus.dts @@ -10,8 +10,8 @@ /* SDP boards with 4430 ES2.3+ or 4460 have external pullups on SCL & SDA */ &dss_hdmi_pins { pinctrl-single,pins = < - 0x5a 0x118 /* hdmi_cec.hdmi_cec INPUT PULLUP | MODE 0 */ - 0x5c 0x100 /* hdmi_scl.hdmi_scl INPUT | MODE 0 */ - 0x5e 0x100 /* hdmi_sda.hdmi_sda INPUT | MODE 0 */ + 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + 0x5c (PIN_INPUT | MUX_MODE0) /* hdmi_scl.hdmi_scl */ + 0x5e (PIN_INPUT | MUX_MODE0) /* hdmi_sda.hdmi_sda */ >; }; diff --git a/arch/arm/boot/dts/omap4-sdp.dts b/arch/arm/boot/dts/omap4-sdp.dts index 509e27c..a10a91b 100644 --- a/arch/arm/boot/dts/omap4-sdp.dts +++ b/arch/arm/boot/dts/omap4-sdp.dts @@ -156,123 +156,123 @@ uart2_pins: pinmux_uart2_pins { pinctrl-single,pins = < - 0xd8 0x118 /* uart2_cts.uart2_cts INPUT_PULLUP | MODE0 */ - 0xda 0 /* uart2_rts.uart2_rts OUTPUT | MODE0 */ - 0xdc 0x118 /* uart2_rx.uart2_rx INPUT_PULLUP | MODE0 */ - 0xde 0 /* uart2_tx.uart2_tx OUTPUT | MODE0 */ + 0xd8 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_cts.uart2_cts */ + 0xda (PIN_OUTPUT | MUX_MODE0) /* uart2_rts.uart2_rts */ + 0xdc (PIN_INPUT_PULLUP | MUX_MODE0) /* uart2_rx.uart2_rx */ + 0xde (PIN_OUTPUT | MUX_MODE0) /* uart2_tx.uart2_tx */ >; }; uart3_pins: pinmux_uart3_pins { pinctrl-single,pins = < - 0x100 0x118 /* uart3_cts_rctx.uart3_cts_rctx INPUT_PULLUP | MODE0 */ - 0x102 0 /* uart3_rts_sd.uart3_rts_sd OUTPUT | MODE0 */ - 0x104 0x100 /* uart3_rx_irrx.uart3_rx_irrx INPUT | MODE0 */ - 0x106 0 /* uart3_tx_irtx.uart3_tx_irtx OUTPUT | MODE0 */ + 0x100 (PIN_INPUT_PULLUP | MUX_MODE0) /* uart3_cts_rctx.uart3_cts_rctx */ + 0x102 (PIN_OUTPUT | MUX_MODE0) /* uart3_rts_sd.uart3_rts_sd */ + 0x104 (PIN_INPUT | MUX_MODE0) /* uart3_rx_irrx.uart3_rx_irrx */ + 0x106 (PIN_OUTPUT | MUX_MODE0) /* uart3_tx_irtx.uart3_tx_irtx */ >; }; uart4_pins: pinmux_uart4_pins { pinctrl-single,pins = < - 0x11c 0x100 /* uart4_rx.uart4_rx INPUT | MODE0 */ - 0x11e 0 /* uart4_tx.uart4_tx OUTPUT | MODE0 */ + 0x11c (PIN_INPUT | MUX_MODE0) /* uart4_rx.uart4_rx */ + 0x11e (PIN_OUTPUT | MUX_MODE0) /* uart4_tx.uart4_tx */ >; }; twl6040_pins: pinmux_twl6040_pins { pinctrl-single,pins = < - 0xe0 0x3 /* hdq_sio.gpio_127 OUTPUT | MODE3 */ - 0x160 0x100 /* sys_nirq2.sys_nirq2 INPUT | MODE0 */ + 0xe0 (PIN_OUTPUT | MUX_MODE3) /* hdq_sio.gpio_127 */ + 0x160 (PIN_INPUT | MUX_MODE0) /* sys_nirq2.sys_nirq2 */ >; }; mcpdm_pins: pinmux_mcpdm_pins { pinctrl-single,pins = < - 0xc6 0x108 /* abe_pdm_ul_data.abe_pdm_ul_data INPUT PULLDOWN | MODE0 */ - 0xc8 0x108 /* abe_pdm_dl_data.abe_pdm_dl_data INPUT PULLDOWN | MODE0 */ - 0xca 0x118 /* abe_pdm_frame.abe_pdm_frame INPUT PULLUP | MODE0 */ - 0xcc 0x108 /* abe_pdm_lb_clk.abe_pdm_lb_clk INPUT PULLDOWN | MODE0 */ - 0xce 0x108 /* abe_clks.abe_clks INPUT PULLDOWN | MODE0 */ + 0xc6 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_ul_data.abe_pdm_ul_data */ + 0xc8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_dl_data.abe_pdm_dl_data */ + 0xca (PIN_INPUT_PULLUP | MUX_MODE0) /* abe_pdm_frame.abe_pdm_frame */ + 0xcc (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_pdm_lb_clk.abe_pdm_lb_clk */ + 0xce (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ >; }; dmic_pins: pinmux_dmic_pins { pinctrl-single,pins = < - 0xd0 0 /* abe_dmic_clk1.abe_dmic_clk1 OUTPUT | MODE0 */ - 0xd2 0x100 /* abe_dmic_din1.abe_dmic_din1 INPUT | MODE0 */ - 0xd4 0x100 /* abe_dmic_din2.abe_dmic_din2 INPUT | MODE0 */ - 0xd6 0x100 /* abe_dmic_din3.abe_dmic_din3 INPUT | MODE0 */ + 0xd0 (PIN_OUTPUT | MUX_MODE0) /* abe_dmic_clk1.abe_dmic_clk1 */ + 0xd2 (PIN_INPUT | MUX_MODE0) /* abe_dmic_din1.abe_dmic_din1 */ + 0xd4 (PIN_INPUT | MUX_MODE0) /* abe_dmic_din2.abe_dmic_din2 */ + 0xd6 (PIN_INPUT | MUX_MODE0) /* abe_dmic_din3.abe_dmic_din3 */ >; }; mcbsp1_pins: pinmux_mcbsp1_pins { pinctrl-single,pins = < - 0xbe 0x100 /* abe_mcbsp1_clkx.abe_mcbsp1_clkx INPUT | MODE0 */ - 0xc0 0x108 /* abe_mcbsp1_dr.abe_mcbsp1_dr INPUT PULLDOWN | MODE0 */ - 0xc2 0x8 /* abe_mcbsp1_dx.abe_mcbsp1_dx OUTPUT PULLDOWN | MODE0 */ - 0xc4 0x100 /* abe_mcbsp1_fsx.abe_mcbsp1_fsx INPUT | MODE0 */ + 0xbe (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_clkx.abe_mcbsp1_clkx */ + 0xc0 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dr.abe_mcbsp1_dr */ + 0xc2 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp1_dx.abe_mcbsp1_dx */ + 0xc4 (PIN_INPUT | MUX_MODE0) /* abe_mcbsp1_fsx.abe_mcbsp1_fsx */ >; }; mcbsp2_pins: pinmux_mcbsp2_pins { pinctrl-single,pins = < - 0xb6 0x100 /* abe_mcbsp2_clkx.abe_mcbsp2_clkx INPUT | MODE0 */ - 0xb8 0x108 /* abe_mcbsp2_dr.abe_mcbsp2_dr INPUT PULLDOWN | MODE0 */ - 0xba 0x8 /* abe_mcbsp2_dx.abe_mcbsp2_dx OUTPUT PULLDOWN | MODE0 */ - 0xbc 0x100 /* abe_mcbsp2_fsx.abe_mcbsp2_fsx INPUT | MODE0 */ + 0xb6 (PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_clkx.abe_mcbsp2_clkx */ + 0xb8 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp2_dr.abe_mcbsp2_dr */ + 0xba (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abe_mcbsp2_dx.abe_mcbsp2_dx */ + 0xbc (PIN_INPUT | MUX_MODE0) /* abe_mcbsp2_fsx.abe_mcbsp2_fsx */ >; }; mcspi1_pins: pinmux_mcspi1_pins { pinctrl-single,pins = < - 0xf2 0x100 /* mcspi1_clk.mcspi1_clk INPUT | MODE0 */ - 0xf4 0x100 /* mcspi1_somi.mcspi1_somi INPUT | MODE0 */ - 0xf6 0x100 /* mcspi1_simo.mcspi1_simo INPUT | MODE0 */ - 0xf8 0x100 /* mcspi1_cs0.mcspi1_cs0 INPUT | MODE0*/ + 0xf2 (PIN_INPUT | MUX_MODE0) /* mcspi1_clk.mcspi1_clk */ + 0xf4 (PIN_INPUT | MUX_MODE0) /* mcspi1_somi.mcspi1_somi */ + 0xf6 (PIN_INPUT | MUX_MODE0) /* mcspi1_simo.mcspi1_simo */ + 0xf8 (PIN_INPUT | MUX_MODE0) /* mcspi1_cs0.mcspi1_cs0 */ >; }; dss_hdmi_pins: pinmux_dss_hdmi_pins { pinctrl-single,pins = < - 0x5a 0x118 /* hdmi_cec.hdmi_cec INPUT PULLUP | MODE 0 */ - 0x5c 0x118 /* hdmi_scl.hdmi_scl INPUT PULLUP | MODE 0 */ - 0x5e 0x118 /* hdmi_sda.hdmi_sda INPUT PULLUP | MODE 0 */ + 0x5a (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_cec.hdmi_cec */ + 0x5c (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_scl.hdmi_scl */ + 0x5e (PIN_INPUT_PULLUP | MUX_MODE0) /* hdmi_sda.hdmi_sda */ >; }; tpd12s015_pins: pinmux_tpd12s015_pins { pinctrl-single,pins = < - 0x22 0x3 /* gpmc_a17.gpio_41 OUTPUT | MODE3 */ - 0x48 0x3 /* gpmc_nbe1.gpio_60 OUTPUT | MODE3 */ - 0x58 0x10b /* hdmi_hpd.gpio_63 INPUT PULLDOWN | MODE3 */ + 0x22 (PIN_OUTPUT | MUX_MODE3) /* gpmc_a17.gpio_41 */ + 0x48 (PIN_OUTPUT | MUX_MODE3) /* gpmc_nbe1.gpio_60 */ + 0x58 (PIN_INPUT_PULLDOWN | MUX_MODE3) /* hdmi_hpd.gpio_63 */ >; }; i2c1_pins: pinmux_i2c1_pins { pinctrl-single,pins = < - 0xe2 0x118 /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */ - 0xe4 0x118 /* i2c1_sda PULLUP | INPUTENABLE | MODE0 */ + 0xe2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ + 0xe4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ >; }; i2c2_pins: pinmux_i2c2_pins { pinctrl-single,pins = < - 0xe6 0x118 /* i2c2_scl PULLUP | INPUTENABLE | MODE0 */ - 0xe8 0x118 /* i2c2_sda PULLUP | INPUTENABLE | MODE0 */ + 0xe6 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_scl */ + 0xe8 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c2_sda */ >; }; i2c3_pins: pinmux_i2c3_pins { pinctrl-single,pins = < - 0xea 0x118 /* i2c3_scl PULLUP | INPUTENABLE | MODE0 */ - 0xec 0x118 /* i2c3_sda PULLUP | INPUTENABLE | MODE0 */ + 0xea (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_scl */ + 0xec (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c3_sda */ >; }; i2c4_pins: pinmux_i2c4_pins { pinctrl-single,pins = < - 0xee 0x118 /* i2c4_scl PULLUP | INPUTENABLE | MODE0 */ - 0xf0 0x118 /* i2c4_sda PULLUP | INPUTENABLE | MODE0 */ + 0xee (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_scl */ + 0xf0 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c4_sda */ >; }; }; diff --git a/arch/arm/boot/dts/omap4.dtsi b/arch/arm/boot/dts/omap4.dtsi index d4304a2..ebf3108 100644 --- a/arch/arm/boot/dts/omap4.dtsi +++ b/arch/arm/boot/dts/omap4.dtsi @@ -16,6 +16,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/pinctrl/omap.h> #include "skeleton.dtsi" diff --git a/arch/arm/boot/dts/omap5-evm.dts b/arch/arm/boot/dts/omap5-evm.dts index f5f55d1..22e9ee8 100644 --- a/arch/arm/boot/dts/omap5-evm.dts +++ b/arch/arm/boot/dts/omap5-evm.dts @@ -40,106 +40,106 @@ twl6040_pins: pinmux_twl6040_pins { pinctrl-single,pins = < - 0x18a 0x6 /* perslimbus2_clock.gpio5_145 OUTPUT | MODE6 */ + 0x18a (PIN_OUTPUT | MUX_MODE6) /* perslimbus2_clock.gpio5_145 */ >; }; mcpdm_pins: pinmux_mcpdm_pins { pinctrl-single,pins = < - 0x142 0x108 /* abe_clks.abe_clks INPUT PULLDOWN | MODE0 */ - 0x15c 0x108 /* abemcpdm_ul_data.abemcpdm_ul_data INPUT PULLDOWN | MODE0 */ - 0x15e 0x108 /* abemcpdm_dl_data.abemcpdm_dl_data INPUT PULLDOWN | MODE0 */ - 0x160 0x118 /* abemcpdm_frame.abemcpdm_frame INPUT PULLUP | MODE0 */ - 0x162 0x108 /* abemcpdm_lb_clk.abemcpdm_lb_clk INPUT PULLDOWN | MODE0 */ + 0x142 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abe_clks.abe_clks */ + 0x15c (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_ul_data.abemcpdm_ul_data */ + 0x15e (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_dl_data.abemcpdm_dl_data */ + 0x160 (PIN_INPUT_PULLUP | MUX_MODE0) /* abemcpdm_frame.abemcpdm_frame */ + 0x162 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcpdm_lb_clk.abemcpdm_lb_clk */ >; }; dmic_pins: pinmux_dmic_pins { pinctrl-single,pins = < - 0x144 0x100 /* abedmic_din1.abedmic_din1 INPUT | MODE0 */ - 0x146 0x100 /* abedmic_din2.abedmic_din2 INPUT | MODE0 */ - 0x148 0x100 /* abedmic_din3.abedmic_din3 INPUT | MODE0 */ - 0x14a 0 /* abedmic_clk1.abedmic_clk1 OUTPUT | MODE0 */ + 0x144 (PIN_INPUT | MUX_MODE0) /* abedmic_din1.abedmic_din1 */ + 0x146 (PIN_INPUT | MUX_MODE0) /* abedmic_din2.abedmic_din2 */ + 0x148 (PIN_INPUT | MUX_MODE0) /* abedmic_din3.abedmic_din3 */ + 0x14a (PIN_OUTPUT | MUX_MODE0) /* abedmic_clk1.abedmic_clk1 */ >; }; mcbsp1_pins: pinmux_mcbsp1_pins { pinctrl-single,pins = < - 0x14c 0x101 /* abedmic_clk2.abemcbsp1_fsx INPUT | MODE1 */ - 0x14e 0x9 /* abedmic_clk3.abemcbsp1_dx OUTPUT PULLDOWN | MODE1 */ - 0x150 0x101 /* abeslimbus1_clock.abemcbsp1_clkx INPUT | MODE0 */ - 0x152 0x109 /* abeslimbus1_data.abemcbsp1_dr INPUT PULLDOWN | MODE1 */ + 0x14c (PIN_INPUT | MUX_MODE1) /* abedmic_clk2.abemcbsp1_fsx */ + 0x14e (PIN_OUTPUT_PULLDOWN | MUX_MODE1) /* abedmic_clk3.abemcbsp1_dx */ + 0x150 (PIN_INPUT | MUX_MODE1) /* abeslimbus1_clock.abemcbsp1_clkx */ + 0x152 (PIN_INPUT_PULLDOWN | MUX_MODE1) /* abeslimbus1_data.abemcbsp1_dr */ >; }; mcbsp2_pins: pinmux_mcbsp2_pins { pinctrl-single,pins = < - 0x154 0x108 /* abemcbsp2_dr.abemcbsp2_dr INPUT PULLDOWN | MODE0 */ - 0x156 0x8 /* abemcbsp2_dx.abemcbsp2_dx OUTPUT PULLDOWN | MODE0 */ - 0x158 0x100 /* abemcbsp2_fsx.abemcbsp2_fsx INPUT | MODE0 */ - 0x15a 0x100 /* abemcbsp2_clkx.abemcbsp2_clkx INPUT | MODE0 */ + 0x154 (PIN_INPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dr.abemcbsp2_dr */ + 0x156 (PIN_OUTPUT_PULLDOWN | MUX_MODE0) /* abemcbsp2_dx.abemcbsp2_dx */ + 0x158 (PIN_INPUT | MUX_MODE0) /* abemcbsp2_fsx.abemcbsp2_fsx */ + 0x15a (PIN_INPUT | MUX_MODE0) /* abemcbsp2_clkx.abemcbsp2_clkx */ >; }; - i2c1_pins: pinmux_i2c1_pins { - pinctrl-single,pins = < - 0x1b2 0x118 /* i2c1_scl PULLUP | INPUTENABLE | MODE0 */ - 0x1b4 0x118 /* i2c1_sda PULLUP | INPUTENABLE | MODE0 */ - >; - }; + i2c1_pins: pinmux_i2c1_pins { + pinctrl-single,pins = < + 0x1b2 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_scl */ + 0x1b4 (PIN_INPUT_PULLUP | MUX_MODE0) /* i2c1_sda */ + >; + }; i2c2_pins: pinmux_i2c2_pins { pinctrl-single,pins = < - 0x178 0x100 /* i2c2_scl INPUTENABLE | MODE0 */ - 0x17a 0x100 /* i2c2_sda INPUTENABLE | MODE0 */ + 0x178 (PIN_INPUT | MUX_MODE0) /* i2c2_scl */ + 0x17a (PIN_INPUT | MUX_MODE0) /* i2c2_sda */ >; }; i2c3_pins: pinmux_i2c3_pins { pinctrl-single,pins = < - 0x13a 0x100 /* i2c3_scl INPUTENABLE | MODE0 */ - 0x13c 0x100 /* i2c3_sda INPUTENABLE | MODE0 */ + 0x13a (PIN_INPUT | MUX_MODE0) /* i2c3_scl */ + 0x13c (PIN_INPUT | MUX_MODE0) /* i2c3_sda */ >; }; i2c4_pins: pinmux_i2c4_pins { pinctrl-single,pins = < - 0xb8 0x100 /* i2c4_scl INPUTENABLE | MODE0 */ - 0xba 0x100 /* i2c4_sda INPUTENABLE | MODE0 */ + 0xb8 (PIN_INPUT | MUX_MODE0) /* i2c4_scl */ + 0xba (PIN_INPUT | MUX_MODE0) /* i2c4_sda */ >; }; i2c5_pins: pinmux_i2c5_pins { pinctrl-single,pins = < - 0x184 0x100 /* i2c5_scl INPUTENABLE | MODE0 */ - 0x186 0x100 /* i2c5_sda INPUTENABLE | MODE0 */ + 0x184 (PIN_INPUT | MUX_MODE0) /* i2c5_scl */ + 0x186 (PIN_INPUT | MUX_MODE0) /* i2c5_sda */ >; }; mcspi2_pins: pinmux_mcspi2_pins { pinctrl-single,pins = < - 0xbc 0x100 /* MCSPI2_CLK INPUTENABLE | MODE0 */ - 0xbe 0x100 /* MCSPI2_SIMO INPUTENABLE | MODE0 */ - 0xc0 0x118 /* MCSPI2_SOMI PULLUP | INPUTENABLE | MODE0*/ - 0xc2 0x0 /* MCSPI2_CS MODE0*/ + 0xbc (PIN_INPUT | MUX_MODE0) /* mcspi2_clk */ + 0xbe (PIN_INPUT | MUX_MODE0) /* mcspi2_simo */ + 0xc0 (PIN_INPUT_PULLUP | MUX_MODE0) /* mcspi2_somi */ + 0xc2 (PIN_OUTPUT | MUX_MODE0) /* mcspi2_cs */ >; }; mcspi3_pins: pinmux_mcspi3_pins { pinctrl-single,pins = < - 0x78 0x101 /* MCSPI2_SOMI INPUTENABLE | MODE1 */ - 0x7a 0x101 /* MCSPI2_CS INPUTENABLE | MODE1 */ - 0x7c 0x101 /* MCSPI2_SIMO INPUTENABLE | MODE1 */ - 0x7e 0x101 /* MCSPI2_CLK INPUTENABLE | MODE1 */ + 0x78 (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */ + 0x7a (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */ + 0x7c (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */ + 0x7e (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */ >; }; mcspi4_pins: pinmux_mcspi4_pins { pinctrl-single,pins = < - 0x164 0x101 /* MCSPI2_CLK INPUTENABLE | MODE1 */ - 0x168 0x101 /* MCSPI2_SIMO INPUTENABLE | MODE1 */ - 0x16a 0x101 /* MCSPI2_SOMI INPUTENABLE | MODE1 */ - 0x16c 0x101 /* MCSPI2_CS INPUTENABLE | MODE1 */ + 0x164 (PIN_INPUT | MUX_MODE1) /* mcspi2_clk */ + 0x168 (PIN_INPUT | MUX_MODE1) /* mcspi2_simo */ + 0x16a (PIN_INPUT | MUX_MODE1) /* mcspi2_somi */ + 0x16c (PIN_INPUT | MUX_MODE1) /* mcspi2_cs */ >; }; }; diff --git a/arch/arm/boot/dts/omap5.dtsi b/arch/arm/boot/dts/omap5.dtsi index 061cf70..825ce300 100644 --- a/arch/arm/boot/dts/omap5.dtsi +++ b/arch/arm/boot/dts/omap5.dtsi @@ -17,6 +17,7 @@ #include <dt-bindings/gpio/gpio.h> #include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/pinctrl/omap.h> #include "skeleton.dtsi" -- 1.7.5.4 ^ permalink raw reply related [flat|nested] 10+ messages in thread
* [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees 2013-05-27 14:52 [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees Florian Vaussard ` (4 preceding siblings ...) 2013-05-27 14:52 ` [PATCH v3 5/5] ARM: dts: OMAP2+: use " Florian Vaussard @ 2013-05-28 8:41 ` Florian Vaussard 2013-05-29 8:46 ` Benoit Cousson 5 siblings, 1 reply; 10+ messages in thread From: Florian Vaussard @ 2013-05-28 8:41 UTC (permalink / raw) To: linux-arm-kernel On 05/27/2013 04:52 PM, Florian Vaussard wrote: > Hello, > > Following a similar proposal by Stephen Warren for tegra [1], this series > makes use of the C preprocessor when compiling OMAP DT files, and > accomplishes some improvements to improve overall readability. > I realized that I should also address am* devices. I will wait for comments on this version, then post a v4. Sorry for the noise. Regards, Florian ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees 2013-05-28 8:41 ` [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees Florian Vaussard @ 2013-05-29 8:46 ` Benoit Cousson 2013-05-29 8:53 ` Florian Vaussard 0 siblings, 1 reply; 10+ messages in thread From: Benoit Cousson @ 2013-05-29 8:46 UTC (permalink / raw) To: linux-arm-kernel Salut Florian, On 05/28/2013 10:41 AM, Florian Vaussard wrote: > > On 05/27/2013 04:52 PM, Florian Vaussard wrote: >> Hello, >> >> Following a similar proposal by Stephen Warren for tegra [1], this series >> makes use of the C preprocessor when compiling OMAP DT files, and >> accomplishes some improvements to improve overall readability. Thanks for that nice cleanup. > I realized that I should also address am* devices. I will wait for comments > on this version, then post a v4. Sorry for the noise. That's up to you, but I can anyway already pulled that series. That AM* patches can go later. Thanks, Benoit ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees 2013-05-29 8:46 ` Benoit Cousson @ 2013-05-29 8:53 ` Florian Vaussard 2013-05-29 9:04 ` Benoit Cousson 0 siblings, 1 reply; 10+ messages in thread From: Florian Vaussard @ 2013-05-29 8:53 UTC (permalink / raw) To: linux-arm-kernel Hello Benoit, On 05/29/2013 10:46 AM, Benoit Cousson wrote: > Salut Florian, > > On 05/28/2013 10:41 AM, Florian Vaussard wrote: >> >> On 05/27/2013 04:52 PM, Florian Vaussard wrote: >>> Hello, >>> >>> Following a similar proposal by Stephen Warren for tegra [1], this series >>> makes use of the C preprocessor when compiling OMAP DT files, and >>> accomplishes some improvements to improve overall readability. > > Thanks for that nice cleanup. > >> I realized that I should also address am* devices. I will wait for comments >> on this version, then post a v4. Sorry for the noise. > > That's up to you, but I can anyway already pulled that series. That AM* > patches can go later. > I saw in your for_3.11/dts branch that you have a couple of patches declaring new pinctrl bindings, so I should base my series of this branch to address these patches as well. So I will send a v4 anyway in the coming days. Thanks, Florian ^ permalink raw reply [flat|nested] 10+ messages in thread
* [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees 2013-05-29 8:53 ` Florian Vaussard @ 2013-05-29 9:04 ` Benoit Cousson 0 siblings, 0 replies; 10+ messages in thread From: Benoit Cousson @ 2013-05-29 9:04 UTC (permalink / raw) To: linux-arm-kernel On 05/29/2013 10:53 AM, Florian Vaussard wrote: > Hello Benoit, > > On 05/29/2013 10:46 AM, Benoit Cousson wrote: >> Salut Florian, >> >> On 05/28/2013 10:41 AM, Florian Vaussard wrote: >>> >>> On 05/27/2013 04:52 PM, Florian Vaussard wrote: >>>> Hello, >>>> >>>> Following a similar proposal by Stephen Warren for tegra [1], this >>>> series >>>> makes use of the C preprocessor when compiling OMAP DT files, and >>>> accomplishes some improvements to improve overall readability. >> >> Thanks for that nice cleanup. >> >>> I realized that I should also address am* devices. I will wait for >>> comments >>> on this version, then post a v4. Sorry for the noise. >> >> That's up to you, but I can anyway already pulled that series. That AM* >> patches can go later. >> > > I saw in your for_3.11/dts branch that you have a couple of patches > declaring > new pinctrl bindings, so I should base my series of this branch to address > these patches as well. So I will send a v4 anyway in the coming days. OK, no problem. I'll wait for the update. Regards, Benoit ^ permalink raw reply [flat|nested] 10+ messages in thread
end of thread, other threads:[~2013-05-29 9:04 UTC | newest] Thread overview: 10+ messages (download: mbox.gz follow: Atom feed -- links below jump to the message on this page -- 2013-05-27 14:52 [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees Florian Vaussard 2013-05-27 14:52 ` [PATCH v3 1/5] ARM: dts: OMAP2+: use #include for all " Florian Vaussard 2013-05-27 14:52 ` [PATCH v3 2/5] ARM: dts: OMAP2+: use existing constants for GPIOs Florian Vaussard 2013-05-27 14:52 ` [PATCH v3 3/5] ARM: dts: OMAP4/5: use existing constants for IRQs Florian Vaussard 2013-05-27 14:52 ` [PATCH v3 4/5] ARM: dts: OMAP2+: header file for pinctrl constants Florian Vaussard 2013-05-27 14:52 ` [PATCH v3 5/5] ARM: dts: OMAP2+: use " Florian Vaussard 2013-05-28 8:41 ` [PATCH v3 0/5] ARM: dts: OMAP2+: use preprocessor for device trees Florian Vaussard 2013-05-29 8:46 ` Benoit Cousson 2013-05-29 8:53 ` Florian Vaussard 2013-05-29 9:04 ` Benoit Cousson
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).