[PATCH] ARM: dts: Add initial support for cm-fx6

[valentin@compulab.co.il (Valentin Raevsky)]

On 10/17/2013 04:45 AM, Steev Klimaszewski wrote:
> On Tue, Oct 15, 2013 at 9:49 AM, Valentin Raevsky
> <valentin@compulab.co.il> wrote:
>> Add initial support for cm-fx6 module.
>>
>> cm-fx6 is a module based on mx6q SoC with the following features:
>> - Up to 4GB of DDR3
>> - 1 LCD/DVI output port
>> - 1 HDMI output port
>> - 2 LVDS LCD ports
>> - Gigabit Ethernet
>> - Analog Audio
>> - CAN
>> - SATA
>> - NAND
>> - PCIE
>>
>> This patch allows to boot up the module, configures the serial console,
>> the Ethernet adapter and the hearbeat led.
>>
>> Signed-off-by: Valentin Raevsky <valentin@compulab.co.il>
>> Acked-by: Igor Grinberg <grinberg@compulab.co.il>
>> ---
>>   arch/arm/boot/dts/cm-fx6.dts |   51 ++++++++++++++++++++++++++++++++++++++++++
>>   1 file changed, 51 insertions(+)
>>   create mode 100644 arch/arm/boot/dts/cm-fx6.dts
>>
>> diff --git a/arch/arm/boot/dts/cm-fx6.dts b/arch/arm/boot/dts/cm-fx6.dts
>> new file mode 100644
>> index 0000000..1080215
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/cm-fx6.dts
>> @@ -0,0 +1,51 @@
>> +/*
>> + * Copyright 2013 CompuLab Ltd.
>> + *
>> + * The code contained herein is licensed under the GNU General Public
>> + * License. You may obtain a copy of the GNU General Public License
>> + * Version 2 or later at the following locations:
>> + *
>> + * http://www.opensource.org/licenses/gpl-license.html
>> + * http://www.gnu.org/copyleft/gpl.html
>> + */
>> +
>> +/dts-v1/;
>> +#include "imx6q.dtsi"
>> +
>> +/ {
>> +       model = "CompuLab CM-FX6";
>> +       compatible = "compulab,cm-fx6", "fsl,imx6q";
>> +
>> +       memory {
>> +               reg = <0x10000000 0x80000000>;
>> +       };
>> +
>> +       leds {
>> +               compatible = "gpio-leds";
>> +
>> +               debug-led {
>> +                       label = "Heartbeat";
>> +                       gpios = <&gpio2 31 0>;
>> +                       linux,default-trigger = "heartbeat";
>> +               };
>> +       };
>> +};
>> +
>> +&gpmi {
>> +       pinctrl-names = "default";
>> +       pinctrl-0 = <&pinctrl_gpmi_nand_1>;
>> +       status = "okay";
>> +};
>> +
>> +&fec {
>> +       pinctrl-names = "default";
>> +       pinctrl-0 = <&pinctrl_enet_1>;
>> +       phy-mode = "rgmii";
>> +       status = "okay";
>> +};
>> +
>> +&uart4 {
>> +       pinctrl-names = "default";
>> +       pinctrl-0 = <&pinctrl_uart4_1>;
>> +       status = "okay";
>> +};
>> --
>> 1.7.9.5
>>
>
> Hi Valentin,
>
> Completely skipped over this, as I wasn't sure what the cm-fx6 was.
> Could we maybe mention that this is commonly referred to as the
> Utilite?
>

Utilite actually consists of two boards:
cm-fx6 -- system on module, sb-fx6m -- base board (extension board).
But you are right, I should have mentioned it.
I will do it in v2.

Regards,
Valentin.