[PATCH 1/4] clk: keystone: use clkod register bits for postdiv

[PATCH 1/4] clk: keystone: use clkod register bits for postdiv

[Murali Karicheri]

DDR3A/B, ARM and PA PLL controllers have clkod register bits for
configuring postdiv values. So use it instead of using fixed
post dividers for these pll controllers. Assume that if fixed-postdiv
attribute is not present, use clkod register value for pistdiv.

Also update the Documentation of bindings to reflect the same.

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
---
 .../devicetree/bindings/clock/keystone-pll.txt     |    8 +++----
 drivers/clk/keystone/pll.c                         |   25 ++++++++++++++++----
 2 files changed, 25 insertions(+), 8 deletions(-)

diff --git a/Documentation/devicetree/bindings/clock/keystone-pll.txt b/Documentation/devicetree/bindings/clock/keystone-pll.txt
index 12bd726..225990f 100644
--- a/Documentation/devicetree/bindings/clock/keystone-pll.txt
+++ b/Documentation/devicetree/bindings/clock/keystone-pll.txt
@@ -17,13 +17,14 @@ Required properties:
 - reg - pll control0 and pll multipler registers
 - reg-names : control and multiplier. The multiplier is applicable only for
 		main pll clock
-- fixed-postdiv : fixed post divider value
+- fixed-postdiv : fixed post divider value. If absent, use clkod register bits
+		for postdiv
 
 Example:
 	mainpllclk: mainpllclk at 2310110 {
 		#clock-cells = <0>;
 		compatible = "ti,keystone,main-pll-clock";
-		clocks = <&refclkmain>;
+		clocks = <&refclksys>;
 		reg = <0x02620350 4>, <0x02310110 4>;
 		reg-names = "control", "multiplier";
 		fixed-postdiv = <2>;
@@ -32,11 +33,10 @@ Example:
 	papllclk: papllclk at 2620358 {
 		#clock-cells = <0>;
 		compatible = "ti,keystone,pll-clock";
-		clocks = <&refclkmain>;
+		clocks = <&refclkpass>;
 		clock-output-names = "pa-pll-clk";
 		reg = <0x02620358 4>;
 		reg-names = "control";
-		fixed-postdiv = <6>;
 	};
 
 Required properties:
diff --git a/drivers/clk/keystone/pll.c b/drivers/clk/keystone/pll.c
index 47a1bd9..f59d5db 100644
--- a/drivers/clk/keystone/pll.c
+++ b/drivers/clk/keystone/pll.c
@@ -24,6 +24,8 @@
 #define MAIN_PLLM_HIGH_MASK	0x7f000
 #define PLLM_HIGH_SHIFT		6
 #define PLLD_MASK		0x3f
+#define CLKOD_MASK		0x780000
+#define CLKOD_SHIFT		19
 
 /**
  * struct clk_pll_data - pll data structure
@@ -41,7 +43,10 @@
  * @pllm_upper_mask: multiplier upper mask
  * @pllm_upper_shift: multiplier upper shift
  * @plld_mask: divider mask
- * @postdiv: Post divider
+ * @clkod_mask: output divider mask
+ * @clkod_shift: output divider shift
+ * @plld_mask: divider mask
+ * @postdiv: Fixed post divider
  */
 struct clk_pll_data {
 	bool has_pllctrl;
@@ -53,6 +58,8 @@ struct clk_pll_data {
 	u32 pllm_upper_mask;
 	u32 pllm_upper_shift;
 	u32 plld_mask;
+	u32 clkod_mask;
+	u32 clkod_shift;
 	u32 postdiv;
 };
 
@@ -87,10 +94,17 @@ static unsigned long clk_pllclk_recalc(struct clk_hw *hw,
 
 	/* bit6-12 of PLLM is in Main PLL control register */
 	val = readl(pll_data->pll_ctl0);
+
 	mult |= ((val & pll_data->pllm_upper_mask)
 			>> pll_data->pllm_upper_shift);
 	prediv = (val & pll_data->plld_mask);
-	postdiv = pll_data->postdiv;
+
+	if (!pll_data->has_pllctrl)
+		/* read post divider from od bits*/
+		postdiv = ((val & pll_data->clkod_mask) >>
+				 pll_data->clkod_shift) + 1;
+	else
+		postdiv = pll_data->postdiv;
 
 	rate /= (prediv + 1);
 	rate = (rate * (mult + 1));
@@ -155,8 +169,11 @@ static void __init _of_pll_clk_init(struct device_node *node, bool pllctrl)
 	}
 
 	parent_name = of_clk_get_parent_name(node, 0);
-	if (of_property_read_u32(node, "fixed-postdiv",	&pll_data->postdiv))
-		goto out;
+	if (of_property_read_u32(node, "fixed-postdiv",	&pll_data->postdiv)) {
+		/* assume the PLL has output divider register bits */
+		pll_data->clkod_mask = CLKOD_MASK;
+		pll_data->clkod_shift = CLKOD_SHIFT;
+	}
 
 	i = of_property_match_string(node, "reg-names", "control");
 	pll_data->pll_ctl0 = of_iomap(node, i);
-- 
1.7.9.5

[PATCH 2/4] keystone: dts: add/modify clock nodes

[Murali Karicheri]

K2 SoC has separate ref clock inputs for various clocks. This patch
adds following changes:-
 - Add separate ref clock nodes for ARM, DDR3A, DDR3B and PA PLL input
   clocks
 - While at it, rename  refclkmain to refclksys based on device User
   Guide naming convention

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
---
 arch/arm/boot/dts/keystone-clocks.dtsi |   48 ++++++++++++++++++++++++--------
 1 file changed, 36 insertions(+), 12 deletions(-)

diff --git a/arch/arm/boot/dts/keystone-clocks.dtsi b/arch/arm/boot/dts/keystone-clocks.dtsi
index d6713b1..3f1cf28 100644
--- a/arch/arm/boot/dts/keystone-clocks.dtsi
+++ b/arch/arm/boot/dts/keystone-clocks.dtsi
@@ -13,17 +13,45 @@ clocks {
 	#size-cells = <1>;
 	ranges;
 
-	refclkmain: refclkmain {
+	refclksys: refclksys {
 		#clock-cells = <0>;
 		compatible = "fixed-clock";
 		clock-frequency = <122880000>;
-		clock-output-names = "refclk-main";
+		clock-output-names = "refclk-sys";
+	};
+
+	refclkpass: refclkpass {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <122880000>;
+		clock-output-names = "refclk-pass";
+	};
+
+	refclkarm: refclkarm {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <125000000>;
+		clock-output-names = "refclk-arm";
+	};
+
+	refclkddr3a: refclkddr3a {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <100000000>;
+		clock-output-names = "refclk-ddr3a";
+	};
+
+	refclkddr3b: refclkddr3b {
+		#clock-cells = <0>;
+		compatible = "fixed-clock";
+		clock-frequency = <100000000>;
+		clock-output-names = "refclk-ddr3b";
 	};
 
 	mainpllclk: mainpllclk at 2310110 {
 		#clock-cells = <0>;
 		compatible = "ti,keystone,main-pll-clock";
-		clocks = <&refclkmain>;
+		clocks = <&refclksys>;
 		reg = <0x02620350 4>, <0x02310110 4>;
 		reg-names = "control", "multiplier";
 		fixed-postdiv = <2>;
@@ -32,47 +60,43 @@ clocks {
 	papllclk: papllclk at 2620358 {
 		#clock-cells = <0>;
 		compatible = "ti,keystone,pll-clock";
-		clocks = <&refclkmain>;
+		clocks = <&refclkpass>;
 		clock-output-names = "pa-pll-clk";
 		reg = <0x02620358 4>;
 		reg-names = "control";
-		fixed-postdiv = <6>;
 	};
 
 	ddr3allclk: ddr3apllclk at 2620360 {
 		#clock-cells = <0>;
 		compatible = "ti,keystone,pll-clock";
-		clocks = <&refclkmain>;
+		clocks = <&refclkddr3a>;
 		clock-output-names = "ddr-3a-pll-clk";
 		reg = <0x02620360 4>;
 		reg-names = "control";
-		fixed-postdiv = <6>;
 	};
 
 	ddr3bllclk: ddr3bpllclk at 2620368 {
 		#clock-cells = <0>;
 		compatible = "ti,keystone,pll-clock";
-		clocks = <&refclkmain>;
+		clocks = <&refclkddr3b>;
 		clock-output-names = "ddr-3b-pll-clk";
 		reg = <0x02620368 4>;
 		reg-names = "control";
-		fixed-postdiv = <6>;
 	};
 
 	armpllclk: armpllclk at 2620370 {
 		#clock-cells = <0>;
 		compatible = "ti,keystone,pll-clock";
-		clocks = <&refclkmain>;
+		clocks = <&refclkarm>;
 		clock-output-names = "arm-pll-clk";
 		reg = <0x02620370 4>;
 		reg-names = "control";
-		fixed-postdiv = <6>;
 	};
 
 	mainmuxclk: mainmuxclk at 2310108 {
 		#clock-cells = <0>;
 		compatible = "ti,keystone,pll-mux-clock";
-		clocks = <&mainpllclk>, <&refclkmain>;
+		clocks = <&mainpllclk>, <&refclksys>;
 		reg = <0x02310108 4>;
 		bit-shift = <23>;
 		bit-mask = <1>;
-- 
1.7.9.5

[PATCH 3/4] keystone: dts: fix typo in the ddr3 pllclk node name

[Murali Karicheri]

Fix following typo
 - ddr3allclk -> ddr3apllclk
 - ddr3bllclk -> ddr3bpllclk

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
---
 arch/arm/boot/dts/keystone-clocks.dtsi |    4 ++--
 1 file changed, 2 insertions(+), 2 deletions(-)

diff --git a/arch/arm/boot/dts/keystone-clocks.dtsi b/arch/arm/boot/dts/keystone-clocks.dtsi
index 3f1cf28..1ebc203 100644
--- a/arch/arm/boot/dts/keystone-clocks.dtsi
+++ b/arch/arm/boot/dts/keystone-clocks.dtsi
@@ -66,7 +66,7 @@ clocks {
 		reg-names = "control";
 	};
 
-	ddr3allclk: ddr3apllclk at 2620360 {
+	ddr3apllclk: ddr3apllclk at 2620360 {
 		#clock-cells = <0>;
 		compatible = "ti,keystone,pll-clock";
 		clocks = <&refclkddr3a>;
@@ -75,7 +75,7 @@ clocks {
 		reg-names = "control";
 	};
 
-	ddr3bllclk: ddr3bpllclk at 2620368 {
+	ddr3bpllclk: ddr3bpllclk at 2620368 {
 		#clock-cells = <0>;
 		compatible = "ti,keystone,pll-clock";
 		clocks = <&refclkddr3b>;
-- 
1.7.9.5

[PATCH 4/4] keystone: dts: add paclk divider clock node

[Murali Karicheri]

PA subsystem has a fixed factor clock at the input which is
input clock divided by 3. This patch adds this clock node to dts

Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
---
 arch/arm/boot/dts/keystone-clocks.dtsi |    9 +++++++++
 1 file changed, 9 insertions(+)

diff --git a/arch/arm/boot/dts/keystone-clocks.dtsi b/arch/arm/boot/dts/keystone-clocks.dtsi
index 1ebc203..3715511 100644
--- a/arch/arm/boot/dts/keystone-clocks.dtsi
+++ b/arch/arm/boot/dts/keystone-clocks.dtsi
@@ -159,6 +159,15 @@ clocks {
 		clock-output-names = "chipclk13";
 	};
 
+	paclk13: paclk13 {
+		#clock-cells = <0>;
+		compatible = "fixed-factor-clock";
+		clocks = <&papllclk>;
+		clock-div = <3>;
+		clock-mult = <1>;
+		clock-output-names = "paclk13";
+	};
+
 	chipclk14: chipclk14 {
 		#clock-cells = <0>;
 		compatible = "fixed-factor-clock";
-- 
1.7.9.5

[PATCH 1/4] clk: keystone: use clkod register bits for postdiv

[Santosh Shilimkar]

On Tuesday 19 November 2013 01:13 PM, Murali Karicheri wrote:
> DDR3A/B, ARM and PA PLL controllers have clkod register bits for
> configuring postdiv values. So use it instead of using fixed
> post dividers for these pll controllers. Assume that if fixed-postdiv
> attribute is not present, use clkod register value for pistdiv.
> 
> Also update the Documentation of bindings to reflect the same.
> 
> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
> ---
>  .../devicetree/bindings/clock/keystone-pll.txt     |    8 +++----
>  drivers/clk/keystone/pll.c                         |   25 ++++++++++++++++----
>  2 files changed, 25 insertions(+), 8 deletions(-)
> 
[..]

> diff --git a/drivers/clk/keystone/pll.c b/drivers/clk/keystone/pll.c
> index 47a1bd9..f59d5db 100644
> --- a/drivers/clk/keystone/pll.c
> +++ b/drivers/clk/keystone/pll.c
> @@ -24,6 +24,8 @@
>  #define MAIN_PLLM_HIGH_MASK	0x7f000
>  #define PLLM_HIGH_SHIFT		6
>  #define PLLD_MASK		0x3f
> +#define CLKOD_MASK		0x780000
> +#define CLKOD_SHIFT		19
>  
>  /**
>   * struct clk_pll_data - pll data structure
> @@ -41,7 +43,10 @@
>   * @pllm_upper_mask: multiplier upper mask
>   * @pllm_upper_shift: multiplier upper shift
>   * @plld_mask: divider mask
> - * @postdiv: Post divider
> + * @clkod_mask: output divider mask
> + * @clkod_shift: output divider shift
> + * @plld_mask: divider mask
> + * @postdiv: Fixed post divider
>   */
>  struct clk_pll_data {
>  	bool has_pllctrl;
> @@ -53,6 +58,8 @@ struct clk_pll_data {
>  	u32 pllm_upper_mask;
>  	u32 pllm_upper_shift;
>  	u32 plld_mask;
> +	u32 clkod_mask;
> +	u32 clkod_shift;
>  	u32 postdiv;
>  };
>  
> @@ -87,10 +94,17 @@ static unsigned long clk_pllclk_recalc(struct clk_hw *hw,
>  
>  	/* bit6-12 of PLLM is in Main PLL control register */
>  	val = readl(pll_data->pll_ctl0);
> +
Drop that extra line. Other than that patch looks fine to me.

Regards,
Santosh

[PATCH 2/4] keystone: dts: add/modify clock nodes

[Santosh Shilimkar]

On Tuesday 19 November 2013 01:13 PM, Murali Karicheri wrote:
> K2 SoC has separate ref clock inputs for various clocks. This patch
> adds following changes:-
>  - Add separate ref clock nodes for ARM, DDR3A, DDR3B and PA PLL input
>    clocks
>  - While at it, rename  refclkmain to refclksys based on device User
>    Guide naming convention
> 
> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
> ---
>  arch/arm/boot/dts/keystone-clocks.dtsi |   48 ++++++++++++++++++++++++--------
>  1 file changed, 36 insertions(+), 12 deletions(-)
> 
> diff --git a/arch/arm/boot/dts/keystone-clocks.dtsi b/arch/arm/boot/dts/keystone-clocks.dtsi
> index d6713b1..3f1cf28 100644
> --- a/arch/arm/boot/dts/keystone-clocks.dtsi
> +++ b/arch/arm/boot/dts/keystone-clocks.dtsi
> @@ -13,17 +13,45 @@ clocks {
>  	#size-cells = <1>;
>  	ranges;
>  
> -	refclkmain: refclkmain {
> +	refclksys: refclksys {
>  		#clock-cells = <0>;
>  		compatible = "fixed-clock";
>  		clock-frequency = <122880000>;
> -		clock-output-names = "refclk-main";
> +		clock-output-names = "refclk-sys";
> +	};
> +
> +	refclkpass: refclkpass {
> +		#clock-cells = <0>;
> +		compatible = "fixed-clock";
> +		clock-frequency = <122880000>;
> +		clock-output-names = "refclk-pass";
> +	};
> +

lets move these nodes which are board dependent to board file.
This came in for NAND patches as well. I suggested to create a
k2hk-evm.dts file.

Regards,
Santosh

[PATCH 3/4] keystone: dts: fix typo in the ddr3 pllclk node name

[Santosh Shilimkar]

On Tuesday 19 November 2013 01:13 PM, Murali Karicheri wrote:
> Fix following typo
>  - ddr3allclk -> ddr3apllclk
>  - ddr3bllclk -> ddr3bpllclk
> 
> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
> ---
Looks good..

regards,
Santosh

[PATCH 4/4] keystone: dts: add paclk divider clock node

[Santosh Shilimkar]

On Tuesday 19 November 2013 01:13 PM, Murali Karicheri wrote:
> PA subsystem has a fixed factor clock at the input which is
> input clock divided by 3. This patch adds this clock node to dts
> 
> Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
> ---
Looks good to me.

regards,
Santosh