From: b.brezillon.dev@gmail.com (boris brezillon dev)
To: linux-arm-kernel@lists.infradead.org
Subject: [linux-sunxi] Re: [RFC PATCH v2 09/14] mtd: nand: add sunxi NFC dt bindings doc
Date: Thu, 30 Jan 2014 09:46:38 +0100 [thread overview]
Message-ID: <52EA116E.3030100@gmail.com> (raw)
In-Reply-To: <1391035079.14902.3.camel@localhost>
Hello Henrik,
Sorry for the noise, I sent the mail to Rob's old address.
On 29/01/2014 23:37, Henrik Nordstr?m wrote:
> ons 2014-01-29 klockan 11:11 -0600 skrev Rob Herring:
>
>> Isn't allwinner,rb implied by a lack of rb-gpios property. Or no R/B
>> pin is an option? If so, don't you need some fixed time delay
>> properties like max erase time?
>>
>> rb-gpios could be added to the generic nand binding as well.
> The Allwinner NAND controller have dedicated RB pins when NAND is
> enabled, only MUXed with other functions when NAND is not enabled.
>
> Leaving RB unconnected is not a valid hardware configuration. The
> controller internal timing engine depends on being able to sense RB to
> sequence NAND commands properly.
This is not true (at least in this driver). It was in yuq's driver because
he was using the NFC_WAIT_FLAG ,and in this case the controller wait
for the native R/B pin to be high before considering the CMD is complete.
This driver choose the appropriate way to test the R/B state of the
NAND chip according to what was specified in the DT:
- allwinner,rb: native R/B id. These pins will be used by the NAND
controller to test the R/B state. Only 0 and 1 are valid because the
NAND controller only support 2 R/B pins.
- rb-gpios: gpio used for R/B tests. This is a simple GPIO and will
use the GPIO subsystem to test the R/B pin state.
- none: the NAND base code will wait some time before and send
STATUS cmd to the NAND to check its status.
BTW, the controller supports 8 CS (8 NAND chips), but only have 2 native
R/B pins, this means you'll have to use the GPIO or standard GET_STATUS
method if you connect 3 or more NAND chips.
And for the record, I still think the rb-gpios property (or whatever
common name you choose: nand-rb-gpios ?) should be part of
the generic NAND binding, because other controllers (at least the
atmel one :)) use GPIOs to test R/B state.
Best Regards,
Boris
>
> Regards
> Henrik
>
next prev parent reply other threads:[~2014-01-30 8:46 UTC|newest]
Thread overview: 50+ messages / expand[flat|nested] mbox.gz Atom feed top
2014-01-29 14:34 [RFC PATCH v2 00/14] mtd: nand: add sunxi NAND Flash Controller support Boris BREZILLON
[not found] ` < 1391006064-28890-4-git-send-email-b.brezillon.dev@gmail.com>
2014-01-29 14:34 ` [RFC PATCH v2 01/14] mtd: nand: retrieve ECC requirements from Hynix READ ID byte 4 Boris BREZILLON
2014-01-29 14:34 ` [RFC PATCH v2 02/14] of: mtd: add NAND ECC level requirements retrieval Boris BREZILLON
2014-01-29 14:34 ` [RFC PATCH v2 03/14] of: mtd: add documentation for nand-ecc-level property Boris BREZILLON
2014-01-29 17:53 ` Ezequiel Garcia
2014-01-29 18:39 ` Boris BREZILLON
2014-02-05 11:15 ` Grant Likely
2014-02-05 13:34 ` Boris BREZILLON
2014-02-05 14:19 ` Ezequiel Garcia
2014-02-17 16:43 ` Grant Likely
2014-02-17 18:19 ` Ezequiel Garcia
2014-01-29 14:34 ` [RFC PATCH v2 04/14] mtd: nand: define struct nand_timings Boris BREZILLON
2014-03-10 13:44 ` Boris BREZILLON
2014-03-11 18:55 ` Jason Gunthorpe
2014-03-12 16:46 ` Boris BREZILLON
2014-03-12 19:07 ` Jason Gunthorpe
2014-03-12 20:18 ` Warner Losh
2014-01-29 14:34 ` [RFC PATCH v2 05/14] mtd: nand: add ONFI timing mode to nand_timings converter Boris BREZILLON
2014-01-29 14:34 ` [RFC PATCH v2 06/14] of: mtd: add NAND timing mode retrieval support Boris BREZILLON
2014-01-29 14:34 ` [RFC PATCH v2 07/14] of: mtd: add documentation for the ONFI NAND timing mode property Boris BREZILLON
2014-01-29 14:34 ` [RFC PATCH v2 08/14] mtd: nand: add sunxi NAND flash controller support Boris BREZILLON
2014-01-29 17:56 ` Jason Gunthorpe
2014-01-29 18:46 ` Ezequiel Garcia
2014-01-29 19:10 ` Jason Gunthorpe
2014-01-30 8:57 ` [linux-sunxi] " Boris BREZILLON
2014-03-10 11:17 ` Boris BREZILLON
2014-03-10 11:37 ` Lucas Stach
2014-03-11 18:45 ` Jason Gunthorpe
2014-01-29 19:02 ` Boris BREZILLON
2014-01-30 11:22 ` Boris BREZILLON
2014-01-29 14:34 ` [RFC PATCH v2 09/14] mtd: nand: add sunxi NFC dt bindings doc Boris BREZILLON
2014-01-29 17:11 ` Rob Herring
2014-01-29 17:12 ` Rob Herring
2014-01-29 18:01 ` Boris BREZILLON
2014-01-29 18:02 ` Gupta, Pekon
2014-01-29 18:33 ` Boris BREZILLON
2014-01-29 18:36 ` Gupta, Pekon
2014-01-29 22:37 ` [linux-sunxi] " Henrik Nordström
2014-01-30 8:38 ` boris brezillon dev
2014-01-30 8:46 ` boris brezillon dev [this message]
2014-01-29 14:34 ` [RFC PATCH v2 10/14] ARM: dt/sunxi: add NFC node to Allwinner A20 SoC Boris BREZILLON
2014-01-29 14:34 ` [RFC PATCH v2 11/14] ARM: dt/sunxi: add NFC pinctrl pin definitions Boris BREZILLON
2014-01-29 14:34 ` [RFC PATCH v2 12/14] ARM: sunxi/dt: enable NAND on cubietruck board Boris BREZILLON
2014-01-29 14:34 ` [RFC PATCH v2 13/14] mtd: nand: add sunxi HW ECC support Boris BREZILLON
2014-01-29 14:34 ` [RFC PATCH v2 14/14] ARM: sunxi/dt: enable HW ECC on cubietruck board Boris BREZILLON
2014-01-30 13:39 ` [RFC PATCH pre-v3 08/14] mtd: nand: add sunxi NAND flash controller support Boris BREZILLON
2014-01-30 14:36 ` Russell King - ARM Linux
2014-01-30 15:04 ` Boris BREZILLON
2014-01-30 13:41 ` [RFC PATCH pre-v3 13/14] mtd: nand: add sunxi HW ECC support Boris BREZILLON
2014-01-30 13:46 ` [RFC PATCH pre-v3 07/14] of: mtd: add documentation for the ONFI NAND timing mode property Boris BREZILLON
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=52EA116E.3030100@gmail.com \
--to=b.brezillon.dev@gmail.com \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).