From mboxrd@z Thu Jan  1 00:00:00 1970
From: tomasz.figa@gmail.com (Tomasz Figa)
Date: Thu, 20 Feb 2014 20:26:11 +0100
Subject: [PATCH 0/6] mmc: sdhci-s3c: Fix base clock source management
In-Reply-To: <52F4AE40.9050907@gmail.com>
References: <1389476346-20396-1-git-send-email-tomasz.figa@gmail.com>
 <52F4AE40.9050907@gmail.com>
Message-ID: <530656D3.7010709@gmail.com>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

Hi Chris,

On 07.02.2014 10:58, Tomasz Figa wrote:
> Hi Chris,
>
> On 11.01.2014 22:39, Tomasz Figa wrote:
>> On platforms prior to Exynos the SDHCI block used internal clock
>> divider controlled by SELFREQ field of CLKCON register to divide base
>> clock selected from several external clocks fed to the block by
>> SELBASECLK bitfield of CONTROL2 register. Depending on wanted clock
>> frequency, different external clock may be the best choice and so
>> the driver needs to switch the SELBASECLK mux on the fly.
>>
>> However the selection logic has been broken for quite some time leaving
>> the controller using always clock 0, which is not always the right
>> source and leading to suboptimal performance of the SDHCI block on
>> affected platforms.
>>
>> This series intends to fix the problems mentioned above and also clean-up
>> clock management code slightly.
>>
>> Tested on S3C6410-based Mini6410 board, with following performance
>> figures:
>>
>> * Before this series (133 MHz HCLK always selected, leading to at most
>>    33 MHz card clock):
>>
>> root at tiny6410:~# hdparm -t /dev/mmcblk0
>>
>> /dev/mmcblk0:
>>   Timing buffered disk reads:  42 MB in  3.10 seconds =  13.54 MB/sec
>> root at tiny6410:~# hdparm -t /dev/mmcblk0
>>
>> /dev/mmcblk0:
>>   Timing buffered disk reads:  44 MB in  3.11 seconds =  14.14 MB/sec
>> root at tiny6410:~#
>>
>> * After this series (48 MHz EPLL clock selected, leading to 48 MHz card
>>    clock):
>>
>> root at tiny6410:~# hdparm -t /dev/mmcblk0
>>
>> /dev/mmcblk0:
>>   Timing buffered disk reads:  56 MB in  3.04 seconds =  18.41 MB/sec
>> root at tiny6410:~# hdparm -t /dev/mmcblk0
>>
>> /dev/mmcblk0:
>>   Timing buffered disk reads:  60 MB in  3.06 seconds =  19.63 MB/sec
>> root at tiny6410:~#
>>
>> Tomasz Figa (6):
>>    mmc: sdhci-s3c: Use shifts to divide by powers of two
>>    mmc: sdhci-s3c: Cache bus clock rates
>>    mmc: sdhci-s3c: Use correct condition to check for clock presence
>>    mmc: sdhci-s3c: Simplify min/max clock calculation
>>    mmc: sdhci-s3c: Fix handling of bus clock switching
>>    mmc: sdhci-s3c: Do not allow frequencies higher than requested
>>
>>   drivers/mmc/host/sdhci-s3c.c | 170
>> ++++++++++++++++++++-----------------------
>>   1 file changed, 77 insertions(+), 93 deletions(-)
>>
>
> What do you think about this series?

Could you take this series for 3.15?

Best regards,
Tomasz