[PATCH] pwm: mxs: set pwm_chip can_sleep flag

[stefan.wahren@i2se.com (Stefan Wahren)]

Hi Alexandre,

Am 08.04.2014 16:18, schrieb Alexandre Belloni:
> On 08/04/2014 at 15:46:59 +0200, Stefan Wahren wrote :
>> Hi Shawn,
>>
>> Am 08.04.2014 13:29, schrieb Shawn Guo:
>>> The .config() calls clk_get_rate() which might sleep, so we need to set
>>> pwm_chip can_sleep flag.  Otherwise, we see the following warning when
>>> using pwm driven heartbeat led.
>>>
>>> WARNING: CPU: 0 PID: 0 at kernel/locking/mutex.c:856 mutex_trylock+0x184/0x1a4()
>>> DEBUG_LOCKS_WARN_ON(in_interrupt())
>>> Modules linked in:
>>> CPU: 0 PID: 0 Comm: swapper Not tainted 3.14.0-rc5 #18
>>> [<c0015420>] (unwind_backtrace) from [<c0012cb0>] (show_stack+0x10/0x14)
>>> [<c0012cb0>] (show_stack) from [<c001daf8>] (warn_slowpath_common+0x6c/0x8c)
>>> [<c001daf8>] (warn_slowpath_common) from [<c001dbac>] (warn_slowpath_fmt+0x30/0x40)
>>> [<c001dbac>] (warn_slowpath_fmt) from [<c045df74>] (mutex_trylock+0x184/0x1a4)
>>> [<c045df74>] (mutex_trylock) from [<c0360950>] (clk_prepare_lock+0xc/0xec)
>>> [<c0360950>] (clk_prepare_lock) from [<c0362020>] (clk_get_rate+0xc/0x68)
>>> [<c0362020>] (clk_get_rate) from [<c028d07c>] (mxs_pwm_config+0x20/0x198)
>>> [<c028d07c>] (mxs_pwm_config) from [<c028bde8>] (pwm_config+0x60/0x70)
>>> [<c028bde8>] (pwm_config) from [<c034b61c>] (__led_pwm_set+0x1c/0x3c)
>>> [<c034b61c>] (__led_pwm_set) from [<c034bc3c>] (led_heartbeat_function+0x70/0x110)
>>> [<c034bc3c>] (led_heartbeat_function) from [<c00292f0>] (call_timer_fn+0x7c/0x164)
>>> [<c00292f0>] (call_timer_fn) from [<c00295c8>] (run_timer_softirq+0x1f0/0x260)
>>> [<c00295c8>] (run_timer_softirq) from [<c002255c>] (__do_softirq+0xc4/0x2f0)
>>> [<c002255c>] (__do_softirq) from [<c0022890>] (irq_exit+0xa4/0x10c)
>>> [<c0022890>] (irq_exit) from [<c0010240>] (handle_IRQ+0x34/0x84)
>>> [<c0010240>] (handle_IRQ) from [<c0013524>] (__irq_svc+0x44/0x54)
>>> [<c0013524>] (__irq_svc) from [<c00107f8>] (arch_cpu_idle+0x40/0x48)
>>> [<c00107f8>] (arch_cpu_idle) from [<c005deb8>] (cpu_startup_entry+0x70/0x198)
>>> [<c005deb8>] (cpu_startup_entry) from [<c060aac8>] (start_kernel+0x2a8/0x2f8)
>>>
>>> Reported-by: Stefan Wahren <stefan.wahren@i2se.com>
>>> Signed-off-by: Shawn Guo <shawn.guo@freescale.com>
>>> ---
>>>  drivers/pwm/pwm-mxs.c | 1 +
>>>  1 file changed, 1 insertion(+)
>>>
>>> diff --git a/drivers/pwm/pwm-mxs.c b/drivers/pwm/pwm-mxs.c
>>> index 9475bc7..4f1bb4e 100644
>>> --- a/drivers/pwm/pwm-mxs.c
>>> +++ b/drivers/pwm/pwm-mxs.c
>>> @@ -147,6 +147,7 @@ static int mxs_pwm_probe(struct platform_device *pdev)
>>>  	mxs->chip.dev = &pdev->dev;
>>>  	mxs->chip.ops = &mxs_pwm_ops;
>>>  	mxs->chip.base = -1;
>>> +	mxs->chip.can_sleep = true;
>>>  	ret = of_property_read_u32(np, "fsl,pwm-number", &mxs->chip.npwm);
>>>  	if (ret < 0) {
>>>  		dev_err(&pdev->dev, "failed to get pwm number: %d\n", ret);
>> thanks for the patch. I've tested it with our i.MX28 board and the
>> warning above never came. So it works.
>> Unfortunately the led still don't behave as expected. If i set the led
>> trigger to heartbeat the led goes on and stays in this state.
>>
>> May be this has something to do with the following discussion
>>
>> http://comments.gmane.org/gmane.linux.leds/208
>>
> This may be but the solution is not correct we want to keep disabling
> the pwm when brightness is 0. Can you try the latest series from
> Russell:
>
> http://thread.gmane.org/gmane.linux.leds/579 and set active_low but keep
> the pwm polarity normal.
>
> Regards,
>

i applied these 5 patches, but it doesn't fix the problem.

Here are my results for the pwm driver led on i.MX28:

version                  | trigger: none          | trigger: heartbeat
-----------------------------------------------------------------------------
3.14                     | OK                     | NOT OK (WARNING, LED
permanent on)
  + shawn's patch        | OK                     | NOT OK (LED
permanent on)
    + russell's patches  | OK                     | NOT OK (LED
permanent on)
      + active-low       | NOT OK (inverse logic) | NOT OK (LED
permanent on)

Russell's patches work as expected, but have not influence on the heartbeat.

Regards,
Stefan