[PATCH 21/29] ARM: orion5x: use DT to describe I2C devices on edmini_v2

[sebastian.hesselbarth@gmail.com (Sebastian Hesselbarth)]

On 04/13/2014 04:39 PM, Thomas Petazzoni wrote:
> This commit converts the already partially DT-converted edmini_v2
> platform to use the Device Tree for I2C bus and devices.
>
> Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
> ---
>   .../dts/orion5x-lacie-ethernet-disk-mini-v2.dts    | 14 +++++++++++++
>   arch/arm/mach-orion5x/edmini_v2-setup.c            | 24 ----------------------
>   2 files changed, 14 insertions(+), 24 deletions(-)
>
> diff --git a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
> index eee42f7..f077b7b 100644
> --- a/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
> +++ b/arch/arm/boot/dts/orion5x-lacie-ethernet-disk-mini-v2.dts
> @@ -10,6 +10,7 @@
>
>   #include <dt-bindings/gpio/gpio.h>
>   #include <dt-bindings/input/input.h>
> +#include <dt-bindings/interrupt-controller/irq.h>
>   #include "orion5x-mv88f5182.dtsi"
>
>   / {
> @@ -54,6 +55,19 @@
>   				};
>   			};
>
> +			i2c at 11000 {

Please use the to-be-introduced node label references.

Sebastian

> +				status = "okay";
> +				clock-frequency = <100000>;
> +				#address-cells = <1>;
> +
> +				rtc at 32 {
> +					compatible = "rs5c372a";
> +					reg = <0x32>;
> +					interrupt-parent = <&gpio0>;
> +					interrupts = <3 IRQ_TYPE_LEVEL_LOW>;
> +				};
> +			};
> +
>   			serial at 12000 {
>   				clock-frequency = <166666667>;
>   				status = "okay";
> diff --git a/arch/arm/mach-orion5x/edmini_v2-setup.c b/arch/arm/mach-orion5x/edmini_v2-setup.c
> index c50469e..75648ab 100644
> --- a/arch/arm/mach-orion5x/edmini_v2-setup.c
> +++ b/arch/arm/mach-orion5x/edmini_v2-setup.c
> @@ -96,17 +96,6 @@ static struct platform_device edmini_v2_nor_flash = {
>   };
>
>   /*****************************************************************************
> - * RTC 5C372a on I2C bus
> - ****************************************************************************/
> -
> -#define EDMINIV2_RTC_GPIO	3
> -
> -static struct i2c_board_info __initdata edmini_v2_i2c_rtc = {
> -	I2C_BOARD_INFO("rs5c372a", 0x32),
> -	.irq = 0,
> -};
> -
> -/*****************************************************************************
>    * General Setup
>    ****************************************************************************/
>
> @@ -125,17 +114,4 @@ void __init edmini_v2_init(void)
>
>   	pr_notice("edmini_v2: USB device port, flash write and power-off "
>   		  "are not yet supported.\n");
> -
> -	/* Get RTC IRQ and register the chip */
> -	if (gpio_request(EDMINIV2_RTC_GPIO, "rtc") == 0) {
> -		if (gpio_direction_input(EDMINIV2_RTC_GPIO) == 0)
> -			edmini_v2_i2c_rtc.irq = gpio_to_irq(EDMINIV2_RTC_GPIO);
> -		else
> -			gpio_free(EDMINIV2_RTC_GPIO);
> -	}
> -
> -	if (edmini_v2_i2c_rtc.irq == 0)
> -		pr_warning("edmini_v2: failed to get RTC IRQ\n");
> -
> -	i2c_register_board_info(0, &edmini_v2_i2c_rtc, 1);
>   }
>