[PATCH v7 1/2] can: xilinx CAN controller support

[mkl@pengutronix.de (Marc Kleine-Budde)]

On 04/22/2014 09:56 AM, Appana Durga Kedareswara Rao wrote:
> Hi Marc,
> 
>> -----Original Message-----
>> From: Michal Simek [mailto:monstr at monstr.eu]
>> Sent: Monday, April 07, 2014 12:27 PM
>> To: Appana Durga Kedareswara Rao
>> Cc: wg at grandegger.com; mkl at pengutronix.de; Michal Simek;
>> grant.likely at linaro.org; robh+dt at kernel.org; linux-can at vger.kernel.org;
>> netdev at vger.kernel.org; linux-arm-kernel at lists.infradead.org; linux-
>> kernel at vger.kernel.org; devicetree at vger.kernel.org; Appana Durga
>> Kedareswara Rao
>> Subject: Re: [PATCH v7 1/2] can: xilinx CAN controller support
>>
>> On 04/02/2014 03:13 PM, Kedareswara rao Appana wrote:
>>> This patch adds xilinx CAN controller support.
>>> This driver supports both ZYNQ CANPS and Soft IP AXI CAN controller.
>>>
>>> Signed-off-by: Kedareswara rao Appana <appanad@xilinx.com>
>>> ---
>>> Changes for v7:
>>> - Updated the driver with review comments.
>>> - Moved the driver bindings doc as a separte patch.
>>> Changes for v6:
>>> - Updated the driver with review comments.
>>> - Used the clock names specified in the data sheet.
>>> - Updated the devicetree bindings doc as per Rob suggestion.
>>> Changes for v5:
>>> - Updated the driver with the review comments.
>>> - Remove the check for the tx fifo full interrupt condition
>>>   form Tx interrupt routine as we are checking it in the _xmit
>>>   routine.
>>> - Clearing the txok interrupt in the tx interrupt routine for
>>>   every Tx can frame.
>>> Changes for v4:
>>> - Added check for the tx fifo full interrupt condition in Tx interrupt
>>> routine.
>>> - Added be iohelper functions.
>>> - Moved the clock enable/disable to probe/remove because of
>>>   Added big endian support for AXI CAN controller case(reading
>>>   a register during probe for that we need to enable clock).
>>> Changes for v3:
>>> - Updated the driver with the review comments.
>>> - Modified the tranmit logic as per Marc suggestion.
>>> - Enabling the clock when the interface is up to reduce the
>>>   Power consumption.
>>> Changes for v2:
>>> - Updated with the review comments.
>>> - Removed the unnecessary debug prints.
>>> - include tx,rx fifo depths in ZYNQ CANPS case also
>>> ---
>>>  drivers/net/can/Kconfig      |    7 +
>>>  drivers/net/can/Makefile     |    1 +
>>>  drivers/net/can/xilinx_can.c | 1176
>>> ++++++++++++++++++++++++++++++++++++++++++
>>>  3 files changed, 1184 insertions(+), 0 deletions(-)  create mode
>>> 100644 drivers/net/can/xilinx_can.c
>>
>> Mark: Any update on this one?
>> BTW: When you apply these patches you should apply 2/2 before 1/2. There
>> is new checking for binding.
>>
> 
> Ping?

Done, when you repost, can you change the order of the patches, so that
the binding comes first.

Marc

-- 
Pengutronix e.K.                  | Marc Kleine-Budde           |
Industrial Linux Solutions        | Phone: +49-231-2826-924     |
Vertretung West/Dortmund          | Fax:   +49-5121-206917-5555 |
Amtsgericht Hildesheim, HRA 2686  | http://www.pengutronix.de   |

-------------- next part --------------
A non-text attachment was scrubbed...
Name: signature.asc
Type: application/pgp-signature
Size: 242 bytes
Desc: OpenPGP digital signature
URL: <http://lists.infradead.org/pipermail/linux-arm-kernel/attachments/20140422/3a6358f9/attachment.sig>