* [RFC 4/4] ARM: dts: exynos5250: Add Spring device tree [not found] <1403486483-4063-1-git-send-email-afaerber@suse.de> @ 2014-06-23 1:21 ` Andreas Färber 2014-06-23 19:47 ` Doug Anderson 0 siblings, 1 reply; 7+ messages in thread From: Andreas Färber @ 2014-06-23 1:21 UTC (permalink / raw) To: linux-arm-kernel Adds initial support for the HP Chromebook 11. Cc: Vincent Palatin <vpalatin@chromium.org> Cc: Doug Anderson <dianders@chromium.org> Cc: Stephan van Schaik <stephan@synkhronix.com> Signed-off-by: Andreas F?rber <afaerber@suse.de> --- arch/arm/boot/dts/Makefile | 1 + arch/arm/boot/dts/exynos5250-spring.dts | 556 ++++++++++++++++++++++++++++++++ 2 files changed, 557 insertions(+) create mode 100644 arch/arm/boot/dts/exynos5250-spring.dts diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile index 5986ff6..dc2c5aa 100644 --- a/arch/arm/boot/dts/Makefile +++ b/arch/arm/boot/dts/Makefile @@ -74,6 +74,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \ exynos5250-arndale.dtb \ exynos5250-smdk5250.dtb \ exynos5250-snow.dtb \ + exynos5250-spring.dtb \ exynos5260-xyref5260.dtb \ exynos5410-smdk5410.dtb \ exynos5420-arndale-octa.dtb \ diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts new file mode 100644 index 0000000..e857d44 --- /dev/null +++ b/arch/arm/boot/dts/exynos5250-spring.dts @@ -0,0 +1,556 @@ +/* + * Google Spring board device tree source + * + * Copyright (c) 2013 Google, Inc + * Copyright (c) 2014 SUSE LINUX Products GmbH + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +/dts-v1/; +#include "exynos5250.dtsi" +#include "exynos5250-cros-common.dtsi" + +/ { + model = "Google Spring"; + compatible = "google,spring", "samsung,exynos5250", "samsung,exynos5"; + + pinctrl at 11400000 { + s5m8767_dvs: s5m8767-dvs { + samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2"; + samsung,pin-function = <0>; + samsung,pin-pud = <1>; + samsung,pin-drv = <0>; + }; + + s5m8767_ds: s5m8767-ds { + samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5"; + samsung,pin-function = <0>; + samsung,pin-pud = <1>; + samsung,pin-drv = <0>; + }; + + tps65090_irq: tps65090-irq { + samsung,pins = "gpx2-6"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + s5m8767_irq: s5m8767-irq { + samsung,pins = "gpx3-2"; + samsung,pin-function = <0>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + + hdmi_hpd_irq: hdmi-hpd-irq { + samsung,pins = "gpx3-7"; + samsung,pin-function = <0>; + samsung,pin-pud = <1>; + samsung,pin-drv = <0>; + }; + }; + + pinctrl at 13400000 { + hsic_reset: hsic-reset { + samsung,pins = "gpe1-0"; + samsung,pin-function = <1>; + samsung,pin-pud = <0>; + samsung,pin-drv = <0>; + }; + }; + + vbat: vbat-fixed-regulator { + compatible = "regulator-fixed"; + regulator-name = "vbat-supply"; + regulator-boot-on; + }; + + usb at 12000000 { + status = "okay"; + }; + + usb3_vbus_reg: regulator-usb3 { + compatible = "regulator-fixed"; + regulator-name = "P5.0V_USB3CON"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + gpio = <&gpe1 0 1>; + pinctrl-names = "default"; + pinctrl-0 = <&hsic_reset>; + enable-active-high; + }; + + phy at 12100000 { + vbus-supply = <&usb3_vbus_reg>; + }; + + usb at 12110000 { + samsung,vbus-gpio = <&gpx1 1 0>; + status = "okay"; + }; + + usb at 12120000 { + status = "okay"; + }; + + mmc at 12220000 { + /* MMC2 pins are used as GPIO for eDP bridge control. */ + status = "disabled"; + }; + + mmc at 12230000 { + status = "disabled"; + }; + + i2c at 12C60000 { + max77686 at 09 { + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + + rtc { + reg = <0x6>; + }; + }; + + s5m8767_pmic at 66 { + compatible = "samsung,s5m8767-pmic"; + reg = <0x66>; + interrupt-parent = <&gpx3>; + interrupts = <2 0>; + pinctrl-names = "default"; + pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>; + wakeup-source; + + s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 1>, /* DVS1 */ + <&gpd1 1 1>, /* DVS2 */ + <&gpd1 2 1>; /* DVS3 */ + + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1>, /* SET1 */ + <&gpx2 4 1>, /* SET2 */ + <&gpx2 5 1>; /* SET3 */ + + /* + * The following arrays of DVS voltages are not used, since we are + * not using GPIOs to control PMIC bucks, but they must be defined + * to please the driver. + */ + s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, + <1250000>, <1200000>, + <1150000>, <1100000>, + <1000000>, <950000>; + + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, + <1100000>, <1100000>, + <1000000>, <1000000>, + <1000000>, <1000000>; + + s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>, + <1200000>, <1200000>; + + clocks { + compatible = "samsung,s5m8767-clk"; + #clock-cells = <1>; + clock-output-names = "en32khz_ap", + "en32khz_cp", + "en32khz_bt"; + }; + + regulators { + s5m_ldo4_reg: LDO4 { + regulator-name = "P1.0V_LDO_OUT4"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + op_mode = <0>; + }; + + s5m_ldo5_reg: LDO5 { + regulator-name = "P1.0V_LDO_OUT5"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + op_mode = <0>; + }; + + s5m_ldo6_reg: LDO6 { + regulator-name = "vdd_mydp"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + op_mode = <3>; + }; + + s5m_ldo7_reg: LDO7 { + regulator-name = "P1.1V_LDO_OUT7"; + regulator-min-microvolt = <1100000>; + regulator-max-microvolt = <1100000>; + regulator-always-on; + op_mode = <3>; + }; + + s5m_ldo8_reg: LDO8 { + regulator-name = "P1.0V_LDO_OUT8"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + op_mode = <3>; + }; + + s5m_ldo10_reg: LDO10 { + regulator-name = "P1.8V_LDO_OUT10"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <3>; + }; + + s5m_ldo11_reg: LDO11 { + regulator-name = "P1.8V_LDO_OUT11"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <0>; + }; + + s5m_ldo12_reg: LDO12 { + regulator-name = "P3.0V_LDO_OUT12"; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + op_mode = <3>; + }; + + s5m_ldo13_reg: LDO13 { + regulator-name = "P1.8V_LDO_OUT13"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <0>; + }; + + s5m_ldo14_reg: LDO14 { + regulator-name = "P1.8V_LDO_OUT14"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <3>; + }; + + s5m_ldo15_reg: LDO15 { + regulator-name = "P1.0V_LDO_OUT15"; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1000000>; + regulator-always-on; + op_mode = <3>; + }; + + s5m_ldo16_reg: LDO16 { + regulator-name = "P1.8V_LDO_OUT16"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + op_mode = <3>; + }; + + s5m_ldo17_reg: LDO17 { + regulator-name = "P2.8V_LDO_OUT17"; + regulator-min-microvolt = <2800000>; + regulator-max-microvolt = <2800000>; + regulator-always-on; + op_mode = <0>; + }; + + s5m_ldo25_reg: LDO25 { + regulator-name = "vdd_bridge"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + op_mode = <1>; + }; + + BUCK1 { + regulator-name = "vdd_mif"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <1300000>; + regulator-always-on; + regulator-boot-on; + op_mode = <3>; + }; + + BUCK2 { + regulator-name = "vdd_arm"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1350000>; + regulator-always-on; + regulator-boot-on; + op_mode = <3>; + }; + + BUCK3 { + regulator-name = "vdd_int"; + regulator-min-microvolt = <900000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + op_mode = <3>; + }; + + BUCK4 { + regulator-name = "vdd_g3d"; + regulator-min-microvolt = <850000>; + regulator-max-microvolt = <1300000>; + regulator-boot-on; + op_mode = <3>; + }; + + BUCK5 { + regulator-name = "P1.8V_BUCK_OUT5"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + regulator-boot-on; + op_mode = <1>; + }; + + BUCK6 { + regulator-name = "P1.2V_BUCK_OUT6"; + regulator-min-microvolt = <1200000>; + regulator-max-microvolt = <1200000>; + regulator-always-on; + regulator-boot-on; + op_mode = <0>; + }; + + BUCK9 { + regulator-name = "vdd_ummc"; + regulator-min-microvolt = <950000>; + regulator-max-microvolt = <3000000>; + regulator-always-on; + regulator-boot-on; + op_mode = <3>; + }; + }; + }; + }; + + i2c at 12C70000 { + trackpad { + status = "disabled"; + }; + }; + + i2c at 12CA0000 { + embedded-controller { + compatible = "google,cros-ec-i2c"; + reg = <0x1e>; + interrupts = <6 0>; + interrupt-parent = <&gpx1>; + wakeup-source; + + keyboard-controller { + compatible = "google,cros-ec-keyb"; + keypad,num-rows = <8>; + keypad,num-columns = <13>; + google,needs-ghost-filter; + linux,keymap = < + 0x0001007d /* L_META */ + 0x0002003b /* F1 */ + 0x00030030 /* B */ + 0x00040044 /* F10 */ + 0x00060031 /* N */ + 0x0008000d /* = */ + 0x000a0064 /* R_ALT */ + + 0x01010001 /* ESC */ + 0x0102003e /* F4 */ + 0x01030022 /* G */ + 0x01040041 /* F7 */ + 0x01060023 /* H */ + 0x01080028 /* ' */ + 0x01090043 /* F9 */ + 0x010b000e /* BKSPACE */ + + 0x0200001d /* L_CTRL */ + 0x0201000f /* TAB */ + 0x0202003d /* F3 */ + 0x02030014 /* T */ + 0x02040040 /* F6 */ + 0x0205001b /* ] */ + 0x02060015 /* Y */ + 0x02070056 /* 102ND */ + 0x0208001a /* [ */ + 0x02090042 /* F8 */ + + 0x03010029 /* GRAVE */ + 0x0302003c /* F2 */ + 0x03030006 /* 5 */ + 0x0304003f /* F5 */ + 0x03060007 /* 6 */ + 0x0308000c /* - */ + 0x030b002b /* \ */ + + 0x04000061 /* R_CTRL */ + 0x0401001e /* A */ + 0x04020020 /* D */ + 0x04030021 /* F */ + 0x0404001f /* S */ + 0x04050025 /* K */ + 0x04060024 /* J */ + 0x04080027 /* ; */ + 0x04090026 /* L */ + 0x040a002b /* \ */ + 0x040b001c /* ENTER */ + + 0x0501002c /* Z */ + 0x0502002e /* C */ + 0x0503002f /* V */ + 0x0504002d /* X */ + 0x05050033 /* , */ + 0x05060032 /* M */ + 0x0507002a /* L_SHIFT */ + 0x05080035 /* / */ + 0x05090034 /* . */ + 0x050B0039 /* SPACE */ + + 0x06010002 /* 1 */ + 0x06020004 /* 3 */ + 0x06030005 /* 4 */ + 0x06040003 /* 2 */ + 0x06050009 /* 8 */ + 0x06060008 /* 7 */ + 0x0608000b /* 0 */ + 0x0609000a /* 9 */ + 0x060a0038 /* L_ALT */ + 0x060b006c /* DOWN */ + 0x060c006a /* RIGHT */ + + 0x07010010 /* Q */ + 0x07020012 /* E */ + 0x07030013 /* R */ + 0x07040011 /* W */ + 0x07050017 /* I */ + 0x07060016 /* U */ + 0x07070036 /* R_SHIFT */ + 0x07080019 /* P */ + 0x07090018 /* O */ + 0x070b0067 /* UP */ + 0x070c0069 /* LEFT */ + >; + }; + }; + + power-regulator { + compatible = "ti,tps65090"; + reg = <0x48>; + + /* + * Config irq to disable internal pulls + * even though we run in polling mode. + */ + pinctrl-names = "default"; + pinctrl-0 = <&tps65090_irq>; + + vsys1-supply = <&vbat>; + vsys2-supply = <&vbat>; + vsys3-supply = <&vbat>; + infet1-supply = <&vbat>; + infet2-supply = <&vbat>; + infet3-supply = <&vbat>; + infet4-supply = <&vbat>; + infet5-supply = <&vbat>; + infet6-supply = <&vbat>; + infet7-supply = <&vbat>; + vsys-l1-supply = <&vbat>; + vsys-l2-supply = <&vbat>; + + regulators { + fet1 { + regulator-name = "vcd_led"; + regulator-min-microvolt = <12000000>; + regulator-max-microvolt = <12000000>; + }; + fet3 { + regulator-name = "wwan_r"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + fet5 { + regulator-name = "cam"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + fet6 { + regulator-name = "lcd_vdd"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + }; + fet7 { + regulator-name = "ts"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + }; + }; + + charger { + compatible = "ti,tps65090-charger"; + }; + }; + }; + + hdmi { + hdmi-en-supply = <&s5m_ldo8_reg>; + vdd-supply = <&s5m_ldo8_reg>; + vdd_osc-supply = <&s5m_ldo10_reg>; + vdd_pll-supply = <&s5m_ldo8_reg>; + }; + + fimd at 14400000 { + status = "okay"; + samsung,invert-vclk; + }; + + dp-controller at 145B0000 { + status = "okay"; + pinctrl-names = "default"; + pinctrl-0 = <&dp_hpd>; + samsung,color-space = <0>; + samsung,dynamic-range = <0>; + samsung,ycbcr-coeff = <0>; + samsung,color-depth = <1>; + samsung,link-rate = <0x0a>; + samsung,lane-count = <1>; + samsung,hpd-gpio = <&gpc3 0 0>; + + display-timings { + native-mode = <&timing1>; + + timing1: timing at 1 { + clock-frequency = <70589280>; + hactive = <1366>; + vactive = <768>; + hfront-porch = <40>; + hback-porch = <40>; + hsync-len = <32>; + vback-porch = <10>; + vfront-porch = <12>; + vsync-len = <6>; + }; + }; + }; + + fixed-rate-clocks { + xxti { + compatible = "samsung,clock-xxti"; + clock-frequency = <24000000>; + }; + }; +}; -- 1.9.3 ^ permalink raw reply related [flat|nested] 7+ messages in thread
* [RFC 4/4] ARM: dts: exynos5250: Add Spring device tree 2014-06-23 1:21 ` [RFC 4/4] ARM: dts: exynos5250: Add Spring device tree Andreas Färber @ 2014-06-23 19:47 ` Doug Anderson 2014-06-23 22:46 ` Andreas Färber 0 siblings, 1 reply; 7+ messages in thread From: Doug Anderson @ 2014-06-23 19:47 UTC (permalink / raw) To: linux-arm-kernel Andreas, Thanks for posting! A first pass on this is below... On Sun, Jun 22, 2014 at 6:21 PM, Andreas F?rber <afaerber@suse.de> wrote: > Adds initial support for the HP Chromebook 11. > > Cc: Vincent Palatin <vpalatin@chromium.org> > Cc: Doug Anderson <dianders@chromium.org> > Cc: Stephan van Schaik <stephan@synkhronix.com> > Signed-off-by: Andreas F?rber <afaerber@suse.de> > --- > arch/arm/boot/dts/Makefile | 1 + > arch/arm/boot/dts/exynos5250-spring.dts | 556 ++++++++++++++++++++++++++++++++ > 2 files changed, 557 insertions(+) > create mode 100644 arch/arm/boot/dts/exynos5250-spring.dts > > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile > index 5986ff6..dc2c5aa 100644 > --- a/arch/arm/boot/dts/Makefile > +++ b/arch/arm/boot/dts/Makefile > @@ -74,6 +74,7 @@ dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \ > exynos5250-arndale.dtb \ > exynos5250-smdk5250.dtb \ > exynos5250-snow.dtb \ > + exynos5250-spring.dtb \ > exynos5260-xyref5260.dtb \ > exynos5410-smdk5410.dtb \ > exynos5420-arndale-octa.dtb \ > diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts > new file mode 100644 > index 0000000..e857d44 > --- /dev/null > +++ b/arch/arm/boot/dts/exynos5250-spring.dts > @@ -0,0 +1,556 @@ > +/* > + * Google Spring board device tree source > + * > + * Copyright (c) 2013 Google, Inc > + * Copyright (c) 2014 SUSE LINUX Products GmbH > + * > + * This program is free software; you can redistribute it and/or modify > + * it under the terms of the GNU General Public License version 2 as > + * published by the Free Software Foundation. > + */ > + > +/dts-v1/; > +#include "exynos5250.dtsi" > +#include "exynos5250-cros-common.dtsi" It is possible we may want to backpedal on the use of "exynos5250-cros-common.dtsi". I know that Olof (now CCed) said he wasn't a fan of how it turned out. The original idea was that it should include the arbitrary set of things that are common between a chunk of Chrome OS boards. As more boards were introduced things would need to migrate from the "common" file to the board files. At the moment the current conventional wisdom is that some duplication is better than the confusing movement of everything back and forth. See exynos5420-peach-pit and exynos5800-peach-pi in ToT linux-next. > +/ { > + model = "Google Spring"; > + compatible = "google,spring", "samsung,exynos5250", "samsung,exynos5"; > + > + pinctrl at 11400000 { The new best way to do things is to put this down at the bottom. See exynos5420-peach-pit as an example: &pinctrl_0 { ... } Note that I believe it was decided that top-level references like that should be sorted alphabetically. If you wanted to apply that run to exynos5250-snow I don't think it would be a terrible idea. > + s5m8767_dvs: s5m8767-dvs { > + samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2"; > + samsung,pin-function = <0>; > + samsung,pin-pud = <1>; > + samsung,pin-drv = <0>; > + }; > + > + s5m8767_ds: s5m8767-ds { > + samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5"; > + samsung,pin-function = <0>; > + samsung,pin-pud = <1>; > + samsung,pin-drv = <0>; > + }; > + > + tps65090_irq: tps65090-irq { > + samsung,pins = "gpx2-6"; > + samsung,pin-function = <0>; > + samsung,pin-pud = <0>; > + samsung,pin-drv = <0>; > + }; > + > + s5m8767_irq: s5m8767-irq { > + samsung,pins = "gpx3-2"; > + samsung,pin-function = <0>; > + samsung,pin-pud = <0>; > + samsung,pin-drv = <0>; > + }; > + > + hdmi_hpd_irq: hdmi-hpd-irq { > + samsung,pins = "gpx3-7"; > + samsung,pin-function = <0>; > + samsung,pin-pud = <1>; > + samsung,pin-drv = <0>; > + }; > + }; > + > + pinctrl at 13400000 { > + hsic_reset: hsic-reset { > + samsung,pins = "gpe1-0"; > + samsung,pin-function = <1>; > + samsung,pin-pud = <0>; > + samsung,pin-drv = <0>; > + }; I'm pretty sure that the HSIC reset needed some funky code to make it work and I'm not sure what the status of that is upstream > + }; > + > + vbat: vbat-fixed-regulator { > + compatible = "regulator-fixed"; > + regulator-name = "vbat-supply"; > + regulator-boot-on; > + }; > + > + usb at 12000000 { > + status = "okay"; > + }; > + > + usb3_vbus_reg: regulator-usb3 { > + compatible = "regulator-fixed"; > + regulator-name = "P5.0V_USB3CON"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + gpio = <&gpe1 0 1>; > + pinctrl-names = "default"; > + pinctrl-0 = <&hsic_reset>; > + enable-active-high; > + }; > + > + phy at 12100000 { > + vbus-supply = <&usb3_vbus_reg>; > + }; > + > + usb at 12110000 { > + samsung,vbus-gpio = <&gpx1 1 0>; > + status = "okay"; > + }; > + > + usb at 12120000 { > + status = "okay"; > + }; > + > + mmc at 12220000 { > + /* MMC2 pins are used as GPIO for eDP bridge control. */ > + status = "disabled"; > + }; > + > + mmc at 12230000 { > + status = "disabled"; > + }; > + > + i2c at 12C60000 { > + max77686 at 09 { There is no max77686 on spring. It uses s5m8767 in the place of max77686. ...you've got "status = disabled", just remove it. > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + > + rtc { > + reg = <0x6>; > + }; > + }; > + > + s5m8767_pmic at 66 { > + compatible = "samsung,s5m8767-pmic"; > + reg = <0x66>; > + interrupt-parent = <&gpx3>; > + interrupts = <2 0>; > + pinctrl-names = "default"; > + pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>; > + wakeup-source; > + > + s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 1>, /* DVS1 */ > + <&gpd1 1 1>, /* DVS2 */ > + <&gpd1 2 1>; /* DVS3 */ > + > + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1>, /* SET1 */ > + <&gpx2 4 1>, /* SET2 */ > + <&gpx2 5 1>; /* SET3 */ The final "1" in each of the GPIO specifiers above should be GPIO_ACTIVE_LOW. > + > + /* > + * The following arrays of DVS voltages are not used, since we are > + * not using GPIOs to control PMIC bucks, but they must be defined > + * to please the driver. > + */ > + s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, > + <1250000>, <1200000>, > + <1150000>, <1100000>, > + <1000000>, <950000>; > + > + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, > + <1100000>, <1100000>, > + <1000000>, <1000000>, > + <1000000>, <1000000>; > + > + s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, > + <1200000>, <1200000>, > + <1200000>, <1200000>, > + <1200000>, <1200000>; > + > + clocks { > + compatible = "samsung,s5m8767-clk"; > + #clock-cells = <1>; > + clock-output-names = "en32khz_ap", > + "en32khz_cp", > + "en32khz_bt"; > + }; > + > + regulators { > + s5m_ldo4_reg: LDO4 { > + regulator-name = "P1.0V_LDO_OUT4"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + regulator-always-on; > + op_mode = <0>; I think that "op_mode" here is questionable. Adding Javier to the thread who was looking at this for max77802 and possibly max77686. > + }; > + > + s5m_ldo5_reg: LDO5 { > + regulator-name = "P1.0V_LDO_OUT5"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + regulator-always-on; > + op_mode = <0>; > + }; > + > + s5m_ldo6_reg: LDO6 { > + regulator-name = "vdd_mydp"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + regulator-always-on; > + op_mode = <3>; > + }; > + > + s5m_ldo7_reg: LDO7 { > + regulator-name = "P1.1V_LDO_OUT7"; > + regulator-min-microvolt = <1100000>; > + regulator-max-microvolt = <1100000>; > + regulator-always-on; > + op_mode = <3>; > + }; > + > + s5m_ldo8_reg: LDO8 { > + regulator-name = "P1.0V_LDO_OUT8"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + regulator-always-on; > + op_mode = <3>; > + }; > + > + s5m_ldo10_reg: LDO10 { > + regulator-name = "P1.8V_LDO_OUT10"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + op_mode = <3>; > + }; > + > + s5m_ldo11_reg: LDO11 { > + regulator-name = "P1.8V_LDO_OUT11"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + op_mode = <0>; > + }; > + > + s5m_ldo12_reg: LDO12 { > + regulator-name = "P3.0V_LDO_OUT12"; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + regulator-always-on; > + op_mode = <3>; > + }; > + > + s5m_ldo13_reg: LDO13 { > + regulator-name = "P1.8V_LDO_OUT13"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + op_mode = <0>; > + }; > + > + s5m_ldo14_reg: LDO14 { > + regulator-name = "P1.8V_LDO_OUT14"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + op_mode = <3>; > + }; > + > + s5m_ldo15_reg: LDO15 { > + regulator-name = "P1.0V_LDO_OUT15"; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1000000>; > + regulator-always-on; > + op_mode = <3>; > + }; > + > + s5m_ldo16_reg: LDO16 { > + regulator-name = "P1.8V_LDO_OUT16"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + op_mode = <3>; > + }; > + > + s5m_ldo17_reg: LDO17 { > + regulator-name = "P2.8V_LDO_OUT17"; > + regulator-min-microvolt = <2800000>; > + regulator-max-microvolt = <2800000>; > + regulator-always-on; > + op_mode = <0>; > + }; > + > + s5m_ldo25_reg: LDO25 { > + regulator-name = "vdd_bridge"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + op_mode = <1>; > + }; > + > + BUCK1 { > + regulator-name = "vdd_mif"; > + regulator-min-microvolt = <950000>; > + regulator-max-microvolt = <1300000>; > + regulator-always-on; > + regulator-boot-on; > + op_mode = <3>; > + }; > + > + BUCK2 { > + regulator-name = "vdd_arm"; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <1350000>; > + regulator-always-on; > + regulator-boot-on; > + op_mode = <3>; > + }; > + > + BUCK3 { > + regulator-name = "vdd_int"; > + regulator-min-microvolt = <900000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + regulator-boot-on; > + op_mode = <3>; > + }; > + > + BUCK4 { > + regulator-name = "vdd_g3d"; > + regulator-min-microvolt = <850000>; > + regulator-max-microvolt = <1300000>; > + regulator-boot-on; > + op_mode = <3>; > + }; > + > + BUCK5 { > + regulator-name = "P1.8V_BUCK_OUT5"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + regulator-boot-on; > + op_mode = <1>; > + }; > + > + BUCK6 { > + regulator-name = "P1.2V_BUCK_OUT6"; > + regulator-min-microvolt = <1200000>; > + regulator-max-microvolt = <1200000>; > + regulator-always-on; > + regulator-boot-on; > + op_mode = <0>; > + }; > + > + BUCK9 { > + regulator-name = "vdd_ummc"; > + regulator-min-microvolt = <950000>; > + regulator-max-microvolt = <3000000>; > + regulator-always-on; > + regulator-boot-on; > + op_mode = <3>; > + }; > + }; > + }; > + }; > + > + i2c at 12C70000 { > + trackpad { > + status = "disabled"; Having this bogus entry here doesn't add anything. Remove it until the trackpad should be added. See http://crbug.com/371114 for a slightly stale bug about trackpad. > + }; > + }; > + > + i2c at 12CA0000 { > + embedded-controller { Add "cros_ec" alias like snow. > + compatible = "google,cros-ec-i2c"; > + reg = <0x1e>; > + interrupts = <6 0>; > + interrupt-parent = <&gpx1>; > + wakeup-source; > + > + keyboard-controller { Don't include keyboard-controller here. Add: #include "cros-ec-keyboard.dtsi" ...at the bottom. Note that I think that the spring EC has a special "charger" key that it uses to indicate when a charger was plugged in and unplugged. I'm not sure how that will end up getting supported upstream but you could just leave it out for now. > + compatible = "google,cros-ec-keyb"; > + keypad,num-rows = <8>; > + keypad,num-columns = <13>; Don't you need pinctrl here? > + google,needs-ghost-filter; > + linux,keymap = < > + 0x0001007d /* L_META */ > + 0x0002003b /* F1 */ > + 0x00030030 /* B */ > + 0x00040044 /* F10 */ > + 0x00060031 /* N */ > + 0x0008000d /* = */ > + 0x000a0064 /* R_ALT */ > + > + 0x01010001 /* ESC */ > + 0x0102003e /* F4 */ > + 0x01030022 /* G */ > + 0x01040041 /* F7 */ > + 0x01060023 /* H */ > + 0x01080028 /* ' */ > + 0x01090043 /* F9 */ > + 0x010b000e /* BKSPACE */ > + > + 0x0200001d /* L_CTRL */ > + 0x0201000f /* TAB */ > + 0x0202003d /* F3 */ > + 0x02030014 /* T */ > + 0x02040040 /* F6 */ > + 0x0205001b /* ] */ > + 0x02060015 /* Y */ > + 0x02070056 /* 102ND */ > + 0x0208001a /* [ */ > + 0x02090042 /* F8 */ > + > + 0x03010029 /* GRAVE */ > + 0x0302003c /* F2 */ > + 0x03030006 /* 5 */ > + 0x0304003f /* F5 */ > + 0x03060007 /* 6 */ > + 0x0308000c /* - */ > + 0x030b002b /* \ */ > + > + 0x04000061 /* R_CTRL */ > + 0x0401001e /* A */ > + 0x04020020 /* D */ > + 0x04030021 /* F */ > + 0x0404001f /* S */ > + 0x04050025 /* K */ > + 0x04060024 /* J */ > + 0x04080027 /* ; */ > + 0x04090026 /* L */ > + 0x040a002b /* \ */ > + 0x040b001c /* ENTER */ > + > + 0x0501002c /* Z */ > + 0x0502002e /* C */ > + 0x0503002f /* V */ > + 0x0504002d /* X */ > + 0x05050033 /* , */ > + 0x05060032 /* M */ > + 0x0507002a /* L_SHIFT */ > + 0x05080035 /* / */ > + 0x05090034 /* . */ > + 0x050B0039 /* SPACE */ > + > + 0x06010002 /* 1 */ > + 0x06020004 /* 3 */ > + 0x06030005 /* 4 */ > + 0x06040003 /* 2 */ > + 0x06050009 /* 8 */ > + 0x06060008 /* 7 */ > + 0x0608000b /* 0 */ > + 0x0609000a /* 9 */ > + 0x060a0038 /* L_ALT */ > + 0x060b006c /* DOWN */ > + 0x060c006a /* RIGHT */ > + > + 0x07010010 /* Q */ > + 0x07020012 /* E */ > + 0x07030013 /* R */ > + 0x07040011 /* W */ > + 0x07050017 /* I */ > + 0x07060016 /* U */ > + 0x07070036 /* R_SHIFT */ > + 0x07080019 /* P */ > + 0x07090018 /* O */ > + 0x070b0067 /* UP */ > + 0x070c0069 /* LEFT */ > + >; > + }; > + }; > + > + power-regulator { > + compatible = "ti,tps65090"; I doubt tps65090 will "just work". Does it? On spring the tps65090 is not directly on the same i2c bus as the EC. It's actually hidden behind the EC. Locally in the ChromeOS tree there appears to be a forked copy of the 65090 regulator driver that's in use just for spring. See this from the ChromeOS 3.8 tree: ./drivers/regulator/tps65090-regulator.c ./drivers/regulator/cros_ec-tps65090.c The Spring version of the driver sends EC commands directly to access the tps65090. It is possible (untested) that you could also talk to tps65090 over an i2c tunnel. On exynos5420-peach-pit we have a full fledged i2c tunnel, but you may be able to extend the tunnel to export an i2c tunnel for spring using something like <https://chromium-review.googlesource.com/66116> > + reg = <0x48>; > + > + /* > + * Config irq to disable internal pulls > + * even though we run in polling mode. > + */ > + pinctrl-names = "default"; > + pinctrl-0 = <&tps65090_irq>; > + > + vsys1-supply = <&vbat>; > + vsys2-supply = <&vbat>; > + vsys3-supply = <&vbat>; > + infet1-supply = <&vbat>; > + infet2-supply = <&vbat>; > + infet3-supply = <&vbat>; > + infet4-supply = <&vbat>; > + infet5-supply = <&vbat>; > + infet6-supply = <&vbat>; > + infet7-supply = <&vbat>; > + vsys-l1-supply = <&vbat>; > + vsys-l2-supply = <&vbat>; > + > + regulators { > + fet1 { > + regulator-name = "vcd_led"; > + regulator-min-microvolt = <12000000>; > + regulator-max-microvolt = <12000000>; > + }; > + fet3 { > + regulator-name = "wwan_r"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + fet5 { > + regulator-name = "cam"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + fet6 { > + regulator-name = "lcd_vdd"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + }; > + fet7 { > + regulator-name = "ts"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + }; > + }; > + > + charger { > + compatible = "ti,tps65090-charger"; > + }; > + }; > + }; > + > + hdmi { > + hdmi-en-supply = <&s5m_ldo8_reg>; > + vdd-supply = <&s5m_ldo8_reg>; > + vdd_osc-supply = <&s5m_ldo10_reg>; > + vdd_pll-supply = <&s5m_ldo8_reg>; > + }; > + > + fimd at 14400000 { > + status = "okay"; > + samsung,invert-vclk; > + }; > + > + dp-controller at 145B0000 { > + status = "okay"; > + pinctrl-names = "default"; > + pinctrl-0 = <&dp_hpd>; This is probably not right. It looks as if spring uses gpc3-0 for display port HPD (as a GPIO). The upstream has this in the exynos5250-pinctrl.dtsi as a different pin. I think you'll need to define your own pinctrl here. > + samsung,color-space = <0>; > + samsung,dynamic-range = <0>; > + samsung,ycbcr-coeff = <0>; > + samsung,color-depth = <1>; > + samsung,link-rate = <0x0a>; > + samsung,lane-count = <1>; > + samsung,hpd-gpio = <&gpc3 0 0>; > + > + display-timings { > + native-mode = <&timing1>; > + > + timing1: timing at 1 { > + clock-frequency = <70589280>; > + hactive = <1366>; > + vactive = <768>; > + hfront-porch = <40>; > + hback-porch = <40>; > + hsync-len = <32>; > + vback-porch = <10>; > + vfront-porch = <12>; > + vsync-len = <6>; > + }; > + }; > + }; > + > + fixed-rate-clocks { > + xxti { > + compatible = "samsung,clock-xxti"; > + clock-frequency = <24000000>; > + }; > + }; > +}; -Doug ^ permalink raw reply [flat|nested] 7+ messages in thread
* [RFC 4/4] ARM: dts: exynos5250: Add Spring device tree 2014-06-23 19:47 ` Doug Anderson @ 2014-06-23 22:46 ` Andreas Färber 2014-06-24 4:05 ` Doug Anderson 0 siblings, 1 reply; 7+ messages in thread From: Andreas Färber @ 2014-06-23 22:46 UTC (permalink / raw) To: linux-arm-kernel Hi Doug, Am 23.06.2014 21:47, schrieb Doug Anderson: > Thanks for posting! A first pass on this is below... Thanks a lot for your quick review! My first big .dts patch, and no datasheets for the hardware at hand as a user. A first pass of replies to my defense. ;) > On Sun, Jun 22, 2014 at 6:21 PM, Andreas F?rber <afaerber@suse.de> wrote: [...] >> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts >> new file mode 100644 >> index 0000000..e857d44 >> --- /dev/null >> +++ b/arch/arm/boot/dts/exynos5250-spring.dts >> @@ -0,0 +1,556 @@ >> +/* >> + * Google Spring board device tree source >> + * >> + * Copyright (c) 2013 Google, Inc >> + * Copyright (c) 2014 SUSE LINUX Products GmbH >> + * >> + * This program is free software; you can redistribute it and/or modify >> + * it under the terms of the GNU General Public License version 2 as >> + * published by the Free Software Foundation. >> + */ >> + >> +/dts-v1/; >> +#include "exynos5250.dtsi" >> +#include "exynos5250-cros-common.dtsi" > > It is possible we may want to backpedal on the use of > "exynos5250-cros-common.dtsi". I know that Olof (now CCed) said he > wasn't a fan of how it turned out. > > The original idea was that it should include the arbitrary set of > things that are common between a chunk of Chrome OS boards. As more > boards were introduced things would need to migrate from the "common" > file to the board files. > > At the moment the current conventional wisdom is that some duplication > is better than the confusing movement of everything back and forth. > See exynos5420-peach-pit and exynos5800-peach-pi in ToT linux-next. > > >> +/ { >> + model = "Google Spring"; >> + compatible = "google,spring", "samsung,exynos5250", "samsung,exynos5"; >> + >> + pinctrl at 11400000 { > > The new best way to do things is to put this down at the bottom. See > exynos5420-peach-pit as an example: > > &pinctrl_0 { > ... > } > > Note that I believe it was decided that top-level references like that > should be sorted alphabetically. Thanks for the hint. (My chosen sort order here was by address.) > If you wanted to apply that run to exynos5250-snow I don't think it > would be a terrible idea. I can of course apply changes to Snow, but I cannot test them myself. >> + s5m8767_dvs: s5m8767-dvs { >> + samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2"; >> + samsung,pin-function = <0>; >> + samsung,pin-pud = <1>; >> + samsung,pin-drv = <0>; >> + }; >> + >> + s5m8767_ds: s5m8767-ds { >> + samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5"; >> + samsung,pin-function = <0>; >> + samsung,pin-pud = <1>; >> + samsung,pin-drv = <0>; >> + }; >> + >> + tps65090_irq: tps65090-irq { >> + samsung,pins = "gpx2-6"; >> + samsung,pin-function = <0>; >> + samsung,pin-pud = <0>; >> + samsung,pin-drv = <0>; >> + }; >> + >> + s5m8767_irq: s5m8767-irq { >> + samsung,pins = "gpx3-2"; >> + samsung,pin-function = <0>; >> + samsung,pin-pud = <0>; >> + samsung,pin-drv = <0>; >> + }; >> + >> + hdmi_hpd_irq: hdmi-hpd-irq { >> + samsung,pins = "gpx3-7"; >> + samsung,pin-function = <0>; >> + samsung,pin-pud = <1>; >> + samsung,pin-drv = <0>; >> + }; >> + }; >> + >> + pinctrl at 13400000 { >> + hsic_reset: hsic-reset { >> + samsung,pins = "gpe1-0"; >> + samsung,pin-function = <1>; >> + samsung,pin-pud = <0>; >> + samsung,pin-drv = <0>; >> + }; > > I'm pretty sure that the HSIC reset needed some funky code to make it > work and I'm not sure what the status of that is upstream Yeah, you mentioned something along those lines. However it's the equivalent of the usb3-vbus-en in -snow.dts. Rename or drop? >> + }; >> + >> + vbat: vbat-fixed-regulator { >> + compatible = "regulator-fixed"; >> + regulator-name = "vbat-supply"; >> + regulator-boot-on; >> + }; >> + >> + usb at 12000000 { >> + status = "okay"; >> + }; >> + >> + usb3_vbus_reg: regulator-usb3 { >> + compatible = "regulator-fixed"; >> + regulator-name = "P5.0V_USB3CON"; >> + regulator-min-microvolt = <5000000>; >> + regulator-max-microvolt = <5000000>; >> + gpio = <&gpe1 0 1>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&hsic_reset>; >> + enable-active-high; >> + }; >> + >> + phy at 12100000 { >> + vbus-supply = <&usb3_vbus_reg>; >> + }; >> + >> + usb at 12110000 { >> + samsung,vbus-gpio = <&gpx1 1 0>; >> + status = "okay"; >> + }; >> + >> + usb at 12120000 { >> + status = "okay"; >> + }; >> + >> + mmc at 12220000 { >> + /* MMC2 pins are used as GPIO for eDP bridge control. */ >> + status = "disabled"; >> + }; >> + >> + mmc at 12230000 { >> + status = "disabled"; >> + }; >> + >> + i2c at 12C60000 { >> + max77686 at 09 { > > There is no max77686 on spring. It uses s5m8767 in the place of max77686. > > ...you've got "status = disabled", just remove it. That's because it's inherited from exynos5250-cros-common.dtsi. The rtc that the system successfully uses is "s5m-rtc", which I guess is on the s5m8767 then? (Confusing that 3.8 Spring had this rtc node despite Snow's max77686 not having it.) >> + #address-cells = <1>; >> + #size-cells = <0>; >> + status = "disabled"; >> + >> + rtc { >> + reg = <0x6>; >> + }; >> + }; >> + >> + s5m8767_pmic at 66 { >> + compatible = "samsung,s5m8767-pmic"; >> + reg = <0x66>; >> + interrupt-parent = <&gpx3>; >> + interrupts = <2 0>; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>; >> + wakeup-source; >> + >> + s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 1>, /* DVS1 */ >> + <&gpd1 1 1>, /* DVS2 */ >> + <&gpd1 2 1>; /* DVS3 */ >> + >> + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1>, /* SET1 */ >> + <&gpx2 4 1>, /* SET2 */ >> + <&gpx2 5 1>; /* SET3 */ > > The final "1" in each of the GPIO specifiers above should be GPIO_ACTIVE_LOW. > > >> + >> + /* >> + * The following arrays of DVS voltages are not used, since we are >> + * not using GPIOs to control PMIC bucks, but they must be defined >> + * to please the driver. >> + */ >> + s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, >> + <1250000>, <1200000>, >> + <1150000>, <1100000>, >> + <1000000>, <950000>; >> + >> + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, >> + <1100000>, <1100000>, >> + <1000000>, <1000000>, >> + <1000000>, <1000000>; >> + >> + s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, >> + <1200000>, <1200000>, >> + <1200000>, <1200000>, >> + <1200000>, <1200000>; >> + >> + clocks { >> + compatible = "samsung,s5m8767-clk"; >> + #clock-cells = <1>; >> + clock-output-names = "en32khz_ap", >> + "en32khz_cp", >> + "en32khz_bt"; >> + }; >> + >> + regulators { >> + s5m_ldo4_reg: LDO4 { >> + regulator-name = "P1.0V_LDO_OUT4"; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1000000>; >> + regulator-always-on; >> + op_mode = <0>; > > I think that "op_mode" here is questionable. Adding Javier to the > thread who was looking at this for max77802 and possibly max77686. Confirming that this op_mode is present in the original 3.8 device tree. (I used dtc to compile my /proc/device-tree tarball back to .dts, so it has hexadecimal <0x0> but that shouldn't matter to dtc AFAIU.) >> + }; >> + >> + s5m_ldo5_reg: LDO5 { >> + regulator-name = "P1.0V_LDO_OUT5"; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1000000>; >> + regulator-always-on; >> + op_mode = <0>; >> + }; >> + >> + s5m_ldo6_reg: LDO6 { >> + regulator-name = "vdd_mydp"; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1000000>; >> + regulator-always-on; >> + op_mode = <3>; >> + }; >> + >> + s5m_ldo7_reg: LDO7 { >> + regulator-name = "P1.1V_LDO_OUT7"; >> + regulator-min-microvolt = <1100000>; >> + regulator-max-microvolt = <1100000>; >> + regulator-always-on; >> + op_mode = <3>; >> + }; >> + >> + s5m_ldo8_reg: LDO8 { >> + regulator-name = "P1.0V_LDO_OUT8"; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1000000>; >> + regulator-always-on; >> + op_mode = <3>; >> + }; >> + >> + s5m_ldo10_reg: LDO10 { >> + regulator-name = "P1.8V_LDO_OUT10"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-always-on; >> + op_mode = <3>; >> + }; >> + >> + s5m_ldo11_reg: LDO11 { >> + regulator-name = "P1.8V_LDO_OUT11"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-always-on; >> + op_mode = <0>; >> + }; >> + >> + s5m_ldo12_reg: LDO12 { >> + regulator-name = "P3.0V_LDO_OUT12"; >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3000000>; >> + regulator-always-on; >> + op_mode = <3>; >> + }; >> + >> + s5m_ldo13_reg: LDO13 { >> + regulator-name = "P1.8V_LDO_OUT13"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-always-on; >> + op_mode = <0>; >> + }; >> + >> + s5m_ldo14_reg: LDO14 { >> + regulator-name = "P1.8V_LDO_OUT14"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-always-on; >> + op_mode = <3>; >> + }; >> + >> + s5m_ldo15_reg: LDO15 { >> + regulator-name = "P1.0V_LDO_OUT15"; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1000000>; >> + regulator-always-on; >> + op_mode = <3>; >> + }; >> + >> + s5m_ldo16_reg: LDO16 { >> + regulator-name = "P1.8V_LDO_OUT16"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-always-on; >> + op_mode = <3>; >> + }; >> + >> + s5m_ldo17_reg: LDO17 { >> + regulator-name = "P2.8V_LDO_OUT17"; >> + regulator-min-microvolt = <2800000>; >> + regulator-max-microvolt = <2800000>; >> + regulator-always-on; >> + op_mode = <0>; >> + }; >> + >> + s5m_ldo25_reg: LDO25 { >> + regulator-name = "vdd_bridge"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-always-on; >> + op_mode = <1>; >> + }; >> + >> + BUCK1 { >> + regulator-name = "vdd_mif"; >> + regulator-min-microvolt = <950000>; >> + regulator-max-microvolt = <1300000>; >> + regulator-always-on; >> + regulator-boot-on; >> + op_mode = <3>; >> + }; >> + >> + BUCK2 { >> + regulator-name = "vdd_arm"; >> + regulator-min-microvolt = <850000>; >> + regulator-max-microvolt = <1350000>; >> + regulator-always-on; >> + regulator-boot-on; >> + op_mode = <3>; >> + }; >> + >> + BUCK3 { >> + regulator-name = "vdd_int"; >> + regulator-min-microvolt = <900000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-always-on; >> + regulator-boot-on; >> + op_mode = <3>; >> + }; >> + >> + BUCK4 { >> + regulator-name = "vdd_g3d"; >> + regulator-min-microvolt = <850000>; >> + regulator-max-microvolt = <1300000>; >> + regulator-boot-on; >> + op_mode = <3>; >> + }; >> + >> + BUCK5 { >> + regulator-name = "P1.8V_BUCK_OUT5"; >> + regulator-min-microvolt = <1800000>; >> + regulator-max-microvolt = <1800000>; >> + regulator-always-on; >> + regulator-boot-on; >> + op_mode = <1>; >> + }; >> + >> + BUCK6 { >> + regulator-name = "P1.2V_BUCK_OUT6"; >> + regulator-min-microvolt = <1200000>; >> + regulator-max-microvolt = <1200000>; >> + regulator-always-on; >> + regulator-boot> > -on; >> + op_mode = <0>; >> + }; >> + >> + BUCK9 { >> + regulator-name = "vdd_ummc"; >> + regulator-min-microvolt = <950000>; >> + regulator-max-microvolt = <3000000>; >> + regulator-always-on; >> + regulator-boot-on; >> + op_mode = <3>; >> + }; >> + }; >> + }; >> + }; >> + >> + i2c at 12C70000 { >> + trackpad { >> + status = "disabled"; > > Having this bogus entry here doesn't add anything. Remove it until > the trackpad should be added. See http://crbug.com/371114 for a > slightly stale bug about trackpad. You misunderstand: This resolves an error about the cypress,cyapa inherited from -cros-common.dtsi. Spring uses a different device and two different I2C addresses. Nodes named trackpad-bootloader and trackpad-alt are prepared here: https://github.com/afaerber/linux/commits/spring-next >> + }; >> + }; >> + >> + i2c at 12CA0000 { >> + embedded-controller { > > Add "cros_ec" alias like snow. > > >> + compatible = "google,cros-ec-i2c"; >> + reg = <0x1e>; >> + interrupts = <6 0>; >> + interrupt-parent = <&gpx1>; >> + wakeup-source; >> + >> + keyboard-controller { > > Don't include keyboard-controller here. Add: > > #include "cros-ec-keyboard.dtsi" > > ...at the bottom. Note that I think that the spring EC has a special > "charger" key that it uses to indicate when a charger was plugged in > and unplugged. I'm not sure how that will end up getting supported > upstream but you could just leave it out for now. Is there such a pending patch for snow? That's what I modeled after. Where is cros-ec-keyboard.dtsi? Don't see it in http://git.kernel.org/cgit/linux/kernel/git/kgene/linux-samsung.git/tree/arch/arm/boot/dts?h=for-next or http://git.kernel.org/cgit/linux/kernel/git/kgene/linux-samsung.git/tree/include/dt-bindings?h=for-next Are you proposing I factor it out? >> + compatible = "google,cros-ec-keyb"; >> + keypad,num-rows = <8>; >> + keypad,num-columns = <13>; > > Don't you need pinctrl here? The keyboard is usable; what would pinctrl be needed for? There's none in the 3.8 device tree. >> + google,needs-ghost-filter; >> + linux,keymap = < >> + 0x0001007d /* L_META */ >> + 0x0002003b /* F1 */ >> + 0x00030030 /* B */ >> + 0x00040044 /* F10 */ >> + 0x00060031 /* N */ >> + 0x0008000d /* = */ >> + 0x000a0064 /* R_ALT */ >> + >> + 0x01010001 /* ESC */ >> + 0x0102003e /* F4 */ >> + 0x01030022 /* G */ >> + 0x01040041 /* F7 */ >> + 0x01060023 /* H */ >> + 0x01080028 /* ' */ >> + 0x01090043 /* F9 */ >> + 0x010b000e /* BKSPACE */ >> + >> + 0x0200001d /* L_CTRL */ >> + 0x0201000f /* TAB */ >> + 0x0202003d /* F3 */ >> + 0x02030014 /* T */ >> + 0x02040040 /* F6 */ >> + 0x0205001b /* ] */ >> + 0x02060015 /* Y */ >> + 0x02070056 /* 102ND */ >> + 0x0208001a /* [ */ >> + 0x02090042 /* F8 */ >> + >> + 0x03010029 /* GRAVE */ >> + 0x0302003c /* F2 */ >> + 0x03030006 /* 5 */ >> + 0x0304003f /* F5 */ >> + 0x03060007 /* 6 */ >> + 0x0308000c /* - */ >> + 0x030b002b /* \ */ >> + >> + 0x04000061 /* R_CTRL */ >> + 0x0401001e /* A */ >> + 0x04020020 /* D */ >> + 0x04030021 /* F */ >> + 0x0404001f /* S */ >> + 0x04050025 /* K */ >> + 0x04060024 /* J */ >> + 0x04080027 /* ; */ >> + 0x04090026 /* L */ >> + 0x040a002b /* \ */ >> + 0x040b001c /* ENTER */ >> + >> + 0x0501002c /* Z */ >> + 0x0502002e /* C */ >> + 0x0503002f /* V */ >> + 0x0504002d /* X */ >> + 0x05050033 /* , */ >> + 0x05060032 /* M */ >> + 0x0507002a /* L_SHIFT */ >> + 0x05080035 /* / */ >> + 0x05090034 /* . */ >> + 0x050B0039 /* SPACE */ >> + >> + 0x06010002 /* 1 */ >> + 0x06020004 /* 3 */ >> + 0x06030005 /* 4 */ >> + 0x06040003 /* 2 */ >> + 0x06050009 /* 8 */ >> + 0x06060008 /* 7 */ >> + 0x0608000b /* 0 */ >> + 0x0609000a /* 9 */ >> + 0x060a0038 /* L_ALT */ >> + 0x060b006c /* DOWN */ >> + 0x060c006a /* RIGHT */ >> + >> + 0x07010010 /* Q */ >> + 0x07020012 /* E */ >> + 0x07030013 /* R */ >> + 0x07040011 /* W */ >> + 0x07050017 /* I */ >> + 0x07060016 /* U */ >> + 0x07070036 /* R_SHIFT */ >> + 0x07080019 /* P */ >> + 0x07090018 /* O */ >> + 0x070b0067 /* UP */ >> + 0x070c0069 /* LEFT */ >> + >; >> + }; >> + }; >> + >> + power-regulator { >> + compatible = "ti,tps65090"; > > I doubt tps65090 will "just work". Does it? Good question. How to tell? :) Not familiar with clocks and regulators. I don't see the nodes referenced anywhere, so I could just try to drop (as I would, as per my cover letter, propose for anything non-essential that turns controversial). If we drop tps65090, can we safely drop vbat-fixed-regulator as well? > On spring the tps65090 is not directly on the same i2c bus as the EC. > It's actually hidden behind the EC. > > Locally in the ChromeOS tree there appears to be a forked copy of the > 65090 regulator driver that's in use just for spring. See this from > the ChromeOS 3.8 tree: > > ./drivers/regulator/tps65090-regulator.c > ./drivers/regulator/cros_ec-tps65090.c > > The Spring version of the driver sends EC commands directly to access > the tps65090. > > It is possible (untested) that you could also talk to tps65090 over an > i2c tunnel. On exynos5420-peach-pit we have a full fledged i2c > tunnel, but you may be able to extend the tunnel to export an i2c > tunnel for spring using something like > <https://chromium-review.googlesource.com/66116> The SBS battery thingy (not in this patch) should also be behind some tunnel. There's none defined in -cros-common.dtsi or in my patch, and still it shows up in dmesg to my surprise, complaining "Couldn't read remote-bus property". >> + reg = <0x48>; >> + >> + /* >> + * Config irq to disable internal pulls >> + * even though we run in polling mode. >> + */ >> + pinctrl-names = "default"; >> + pinctrl-0 = <&tps65090_irq>; >> + >> + vsys1-supply = <&vbat>; >> + vsys2-supply = <&vbat>; >> + vsys3-supply = <&vbat>; >> + infet1-supply = <&vbat>; >> + infet2-supply = <&vbat>; >> + infet3-supply = <&vbat>; >> + infet4-supply = <&vbat>; >> + infet5-supply = <&vbat>; >> + infet6-supply = <&vbat>; >> + infet7-supply = <&vbat>; >> + vsys-l1-supply = <&vbat>; >> + vsys-l2-supply = <&vbat>; >> + >> + regulators { >> + fet1 { >> + regulator-name = "vcd_led"; >> + regulator-min-microvolt = <12000000>; >> + regulator-max-microvolt = <12000000>; >> + }; >> + fet3 { >> + regulator-name = "wwan_r"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-always-on; >> + }; >> + fet5 { >> + regulator-name = "cam"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + regulator-always-on; >> + }; >> + fet6 { >> + regulator-name = "lcd_vdd"; >> + regulator-min-microvolt = <3300000>; >> + regulator-max-microvolt = <3300000>; >> + }; >> + fet7 { >> + regulator-name = "ts"; >> + regulator-min-microvolt = <5000000>; >> + regulator-max-microvolt = <5000000>; >> + }; >> + }; >> + >> + charger { >> + compatible = "ti,tps65090-charger"; >> + }; >> + }; >> + }; >> + >> + hdmi { >> + hdmi-en-supply = <&s5m_ldo8_reg>; >> + vdd-supply = <&s5m_ldo8_reg>; >> + vdd_osc-supply = <&s5m_ldo10_reg>; >> + vdd_pll-supply = <&s5m_ldo8_reg>; >> + }; >> + >> + fimd at 14400000 { >> + status = "okay"; >> + samsung,invert-vclk; >> + }; >> + >> + dp-controller at 145B0000 { >> + status = "okay"; >> + pinctrl-names = "default"; >> + pinctrl-0 = <&dp_hpd>; > > This is probably not right. It looks as if spring uses gpc3-0 for > display port HPD (as a GPIO). The upstream has this in the > exynos5250-pinctrl.dtsi as a different pin. > > I think you'll need to define your own pinctrl here. > > >> + samsung,color-space = <0>; >> + samsung,dynamic-range = <0>; >> + samsung,ycbcr-coeff = <0>; >> + samsung,color-depth = <1>; >> + samsung,link-rate = <0x0a>; >> + samsung,lane-count = <1>; >> + samsung,hpd-gpio = <&gpc3 0 0>; >> + >> + display-timings { >> + native-mode = <&timing1>; >> + >> + timing1: timing at 1 { >> + clock-frequency = <70589280>; >> + hactive = <1366>; >> + vactive = <768>; >> + hfront-porch = <40>; >> + hback-porch = <40>; >> + hsync-len = <32>; >> + vback-porch = <10>; >> + vfront-porch = <12>; >> + vsync-len = <6>; >> + }; >> + }; >> + }; >> + >> + fixed-rate-clocks { >> + xxti { >> + compatible = "samsung,clock-xxti"; >> + clock-frequency = <24000000>; >> + }; >> + }; >> +}; Will check on the other suggestions. Thanks, Andreas -- SUSE LINUX Products GmbH, Maxfeldstr. 5, 90409 N?rnberg, Germany GF: Jeff Hawn, Jennifer Guild, Felix Imend?rffer; HRB 16746 AG N?rnberg ^ permalink raw reply [flat|nested] 7+ messages in thread
* [RFC 4/4] ARM: dts: exynos5250: Add Spring device tree 2014-06-23 22:46 ` Andreas Färber @ 2014-06-24 4:05 ` Doug Anderson 2014-06-24 10:06 ` Javier Martinez Canillas 2014-06-24 15:06 ` Vincent Palatin 0 siblings, 2 replies; 7+ messages in thread From: Doug Anderson @ 2014-06-24 4:05 UTC (permalink / raw) To: linux-arm-kernel Andreas, On Mon, Jun 23, 2014 at 3:46 PM, Andreas F?rber <afaerber@suse.de> wrote: > Hi Doug, > > Am 23.06.2014 21:47, schrieb Doug Anderson: >> Thanks for posting! A first pass on this is below... > > Thanks a lot for your quick review! My first big .dts patch, and no > datasheets for the hardware at hand as a user. > > A first pass of replies to my defense. ;) > >> On Sun, Jun 22, 2014 at 6:21 PM, Andreas F?rber <afaerber@suse.de> wrote: > [...] >>> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts >>> new file mode 100644 >>> index 0000000..e857d44 >>> --- /dev/null >>> +++ b/arch/arm/boot/dts/exynos5250-spring.dts >>> @@ -0,0 +1,556 @@ >>> +/* >>> + * Google Spring board device tree source >>> + * >>> + * Copyright (c) 2013 Google, Inc >>> + * Copyright (c) 2014 SUSE LINUX Products GmbH >>> + * >>> + * This program is free software; you can redistribute it and/or modify >>> + * it under the terms of the GNU General Public License version 2 as >>> + * published by the Free Software Foundation. >>> + */ >>> + >>> +/dts-v1/; >>> +#include "exynos5250.dtsi" >>> +#include "exynos5250-cros-common.dtsi" >> >> It is possible we may want to backpedal on the use of >> "exynos5250-cros-common.dtsi". I know that Olof (now CCed) said he >> wasn't a fan of how it turned out. >> >> The original idea was that it should include the arbitrary set of >> things that are common between a chunk of Chrome OS boards. As more >> boards were introduced things would need to migrate from the "common" >> file to the board files. >> >> At the moment the current conventional wisdom is that some duplication >> is better than the confusing movement of everything back and forth. >> See exynos5420-peach-pit and exynos5800-peach-pi in ToT linux-next. >> >> >>> +/ { >>> + model = "Google Spring"; >>> + compatible = "google,spring", "samsung,exynos5250", "samsung,exynos5"; >>> + >>> + pinctrl at 11400000 { >> >> The new best way to do things is to put this down at the bottom. See >> exynos5420-peach-pit as an example: >> >> &pinctrl_0 { >> ... >> } >> >> Note that I believe it was decided that top-level references like that >> should be sorted alphabetically. > > Thanks for the hint. (My chosen sort order here was by address.) > >> If you wanted to apply that run to exynos5250-snow I don't think it >> would be a terrible idea. > > I can of course apply changes to Snow, but I cannot test them myself. If you want to send up a patch like that I'm happy to give it a once over and also to test it. ...but don't feel obligated >>> + s5m8767_dvs: s5m8767-dvs { >>> + samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2"; >>> + samsung,pin-function = <0>; >>> + samsung,pin-pud = <1>; >>> + samsung,pin-drv = <0>; >>> + }; >>> + >>> + s5m8767_ds: s5m8767-ds { >>> + samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5"; >>> + samsung,pin-function = <0>; >>> + samsung,pin-pud = <1>; >>> + samsung,pin-drv = <0>; >>> + }; >>> + >>> + tps65090_irq: tps65090-irq { >>> + samsung,pins = "gpx2-6"; >>> + samsung,pin-function = <0>; >>> + samsung,pin-pud = <0>; >>> + samsung,pin-drv = <0>; >>> + }; >>> + >>> + s5m8767_irq: s5m8767-irq { >>> + samsung,pins = "gpx3-2"; >>> + samsung,pin-function = <0>; >>> + samsung,pin-pud = <0>; >>> + samsung,pin-drv = <0>; >>> + }; >>> + >>> + hdmi_hpd_irq: hdmi-hpd-irq { >>> + samsung,pins = "gpx3-7"; >>> + samsung,pin-function = <0>; >>> + samsung,pin-pud = <1>; >>> + samsung,pin-drv = <0>; >>> + }; >>> + }; >>> + >>> + pinctrl at 13400000 { >>> + hsic_reset: hsic-reset { >>> + samsung,pins = "gpe1-0"; >>> + samsung,pin-function = <1>; >>> + samsung,pin-pud = <0>; >>> + samsung,pin-drv = <0>; >>> + }; >> >> I'm pretty sure that the HSIC reset needed some funky code to make it >> work and I'm not sure what the status of that is upstream > > Yeah, you mentioned something along those lines. However it's the > equivalent of the usb3-vbus-en in -snow.dts. Rename or drop? On snow locally I see USB2 vbus is gpx1-1 and USB3 vbus is gpx2-7. I don't see that in spring. This will take more time than I have right now to track down. I added Julius to the thread in case he has time to answer and can suggest what to do for upstream purposes. I may be able to look more tomorrow. You can always send up the next version and include this and we'll look at it again. >>> + }; >>> + >>> + vbat: vbat-fixed-regulator { >>> + compatible = "regulator-fixed"; >>> + regulator-name = "vbat-supply"; >>> + regulator-boot-on; >>> + }; >>> + >>> + usb at 12000000 { >>> + status = "okay"; >>> + }; >>> + >>> + usb3_vbus_reg: regulator-usb3 { >>> + compatible = "regulator-fixed"; >>> + regulator-name = "P5.0V_USB3CON"; >>> + regulator-min-microvolt = <5000000>; >>> + regulator-max-microvolt = <5000000>; >>> + gpio = <&gpe1 0 1>; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&hsic_reset>; >>> + enable-active-high; >>> + }; >>> + >>> + phy at 12100000 { >>> + vbus-supply = <&usb3_vbus_reg>; >>> + }; >>> + >>> + usb at 12110000 { >>> + samsung,vbus-gpio = <&gpx1 1 0>; >>> + status = "okay"; >>> + }; >>> + >>> + usb at 12120000 { >>> + status = "okay"; >>> + }; >>> + >>> + mmc at 12220000 { >>> + /* MMC2 pins are used as GPIO for eDP bridge control. */ >>> + status = "disabled"; >>> + }; >>> + >>> + mmc at 12230000 { >>> + status = "disabled"; >>> + }; >>> + >>> + i2c at 12C60000 { >>> + max77686 at 09 { >> >> There is no max77686 on spring. It uses s5m8767 in the place of max77686. >> >> ...you've got "status = disabled", just remove it. > > That's because it's inherited from exynos5250-cros-common.dtsi. Ah, right. So if we're keeping cros-common the proper thing to do is to move it out of cros-common in a patch before this one. ...but I think people might be happier if you simply don't include cros-common. > The rtc that the system successfully uses is "s5m-rtc", which I guess is > on the s5m8767 then? (Confusing that 3.8 Spring had this rtc node > despite Snow's max77686 not having it.) I think it's not really supposed to. It was a bit of a hack to handle the fact that the RTC has two different i2c addresses on both the 77686 and this PMIC. The max77686 driver upstream handles it all in code and doesn't ask the device tree to list both addresses. I think that _upstream_ snow doesn't have the node but _downstream_ spring might have the node (though having a child of a disabled node isn't particularly useful). >>> + #address-cells = <1>; >>> + #size-cells = <0>; >>> + status = "disabled"; >>> + >>> + rtc { >>> + reg = <0x6>; >>> + }; >>> + }; >>> + >>> + s5m8767_pmic at 66 { >>> + compatible = "samsung,s5m8767-pmic"; >>> + reg = <0x66>; >>> + interrupt-parent = <&gpx3>; >>> + interrupts = <2 0>; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>; >>> + wakeup-source; >>> + >>> + s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 1>, /* DVS1 */ >>> + <&gpd1 1 1>, /* DVS2 */ >>> + <&gpd1 2 1>; /* DVS3 */ >>> + >>> + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1>, /* SET1 */ >>> + <&gpx2 4 1>, /* SET2 */ >>> + <&gpx2 5 1>; /* SET3 */ >> >> The final "1" in each of the GPIO specifiers above should be GPIO_ACTIVE_LOW. >> >> >>> + >>> + /* >>> + * The following arrays of DVS voltages are not used, since we are >>> + * not using GPIOs to control PMIC bucks, but they must be defined >>> + * to please the driver. >>> + */ >>> + s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, >>> + <1250000>, <1200000>, >>> + <1150000>, <1100000>, >>> + <1000000>, <950000>; >>> + >>> + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, >>> + <1100000>, <1100000>, >>> + <1000000>, <1000000>, >>> + <1000000>, <1000000>; >>> + >>> + s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, >>> + <1200000>, <1200000>, >>> + <1200000>, <1200000>, >>> + <1200000>, <1200000>; >>> + >>> + clocks { >>> + compatible = "samsung,s5m8767-clk"; >>> + #clock-cells = <1>; >>> + clock-output-names = "en32khz_ap", >>> + "en32khz_cp", >>> + "en32khz_bt"; >>> + }; >>> + >>> + regulators { >>> + s5m_ldo4_reg: LDO4 { >>> + regulator-name = "P1.0V_LDO_OUT4"; >>> + regulator-min-microvolt = <1000000>; >>> + regulator-max-microvolt = <1000000>; >>> + regulator-always-on; >>> + op_mode = <0>; >> >> I think that "op_mode" here is questionable. Adding Javier to the >> thread who was looking at this for max77802 and possibly max77686. > > Confirming that this op_mode is present in the original 3.8 device tree. Yes and it needs to be handled eventually. It makes suspend/resume work properly. ...but I think it needs to be thought out better. ...but given that other users of this PMIC have it I guess it makes sense to leave it in. Javier was going to try to think it through better for max77686 and max77802. > (I used dtc to compile my /proc/device-tree tarball back to .dts, so it > has hexadecimal <0x0> but that shouldn't matter to dtc AFAIU.) > >>> + }; >>> + >>> + s5m_ldo5_reg: LDO5 { >>> + regulator-name = "P1.0V_LDO_OUT5"; >>> + regulator-min-microvolt = <1000000>; >>> + regulator-max-microvolt = <1000000>; >>> + regulator-always-on; >>> + op_mode = <0>; >>> + }; >>> + >>> + s5m_ldo6_reg: LDO6 { >>> + regulator-name = "vdd_mydp"; >>> + regulator-min-microvolt = <1000000>; >>> + regulator-max-microvolt = <1000000>; >>> + regulator-always-on; >>> + op_mode = <3>; >>> + }; >>> + >>> + s5m_ldo7_reg: LDO7 { >>> + regulator-name = "P1.1V_LDO_OUT7"; >>> + regulator-min-microvolt = <1100000>; >>> + regulator-max-microvolt = <1100000>; >>> + regulator-always-on; >>> + op_mode = <3>; >>> + }; >>> + >>> + s5m_ldo8_reg: LDO8 { >>> + regulator-name = "P1.0V_LDO_OUT8"; >>> + regulator-min-microvolt = <1000000>; >>> + regulator-max-microvolt = <1000000>; >>> + regulator-always-on; >>> + op_mode = <3>; >>> + }; >>> + >>> + s5m_ldo10_reg: LDO10 { >>> + regulator-name = "P1.8V_LDO_OUT10"; >>> + regulator-min-microvolt = <1800000>; >>> + regulator-max-microvolt = <1800000>; >>> + regulator-always-on; >>> + op_mode = <3>; >>> + }; >>> + >>> + s5m_ldo11_reg: LDO11 { >>> + regulator-name = "P1.8V_LDO_OUT11"; >>> + regulator-min-microvolt = <1800000>; >>> + regulator-max-microvolt = <1800000>; >>> + regulator-always-on; >>> + op_mode = <0>; >>> + }; >>> + >>> + s5m_ldo12_reg: LDO12 { >>> + regulator-name = "P3.0V_LDO_OUT12"; >>> + regulator-min-microvolt = <3000000>; >>> + regulator-max-microvolt = <3000000>; >>> + regulator-always-on; >>> + op_mode = <3>; >>> + }; >>> + >>> + s5m_ldo13_reg: LDO13 { >>> + regulator-name = "P1.8V_LDO_OUT13"; >>> + regulator-min-microvolt = <1800000>; >>> + regulator-max-microvolt = <1800000>; >>> + regulator-always-on; >>> + op_mode = <0>; >>> + }; >>> + >>> + s5m_ldo14_reg: LDO14 { >>> + regulator-name = "P1.8V_LDO_OUT14"; >>> + regulator-min-microvolt = <1800000>; >>> + regulator-max-microvolt = <1800000>; >>> + regulator-always-on; >>> + op_mode = <3>; >>> + }; >>> + >>> + s5m_ldo15_reg: LDO15 { >>> + regulator-name = "P1.0V_LDO_OUT15"; >>> + regulator-min-microvolt = <1000000>; >>> + regulator-max-microvolt = <1000000>; >>> + regulator-always-on; >>> + op_mode = <3>; >>> + }; >>> + >>> + s5m_ldo16_reg: LDO16 { >>> + regulator-name = "P1.8V_LDO_OUT16"; >>> + regulator-min-microvolt = <1800000>; >>> + regulator-max-microvolt = <1800000>; >>> + regulator-always-on; >>> + op_mode = <3>; >>> + }; >>> + >>> + s5m_ldo17_reg: LDO17 { >>> + regulator-name = "P2.8V_LDO_OUT17"; >>> + regulator-min-microvolt = <2800000>; >>> + regulator-max-microvolt = <2800000>; >>> + regulator-always-on; >>> + op_mode = <0>; >>> + }; >>> + >>> + s5m_ldo25_reg: LDO25 { >>> + regulator-name = "vdd_bridge"; >>> + regulator-min-microvolt = <1200000>; >>> + regulator-max-microvolt = <1200000>; >>> + regulator-always-on; >>> + op_mode = <1>; >>> + }; >>> + >>> + BUCK1 { >>> + regulator-name = "vdd_mif"; >>> + regulator-min-microvolt = <950000>; >>> + regulator-max-microvolt = <1300000>; >>> + regulator-always-on; >>> + regulator-boot-on; >>> + op_mode = <3>; >>> + }; >>> + >>> + BUCK2 { >>> + regulator-name = "vdd_arm"; >>> + regulator-min-microvolt = <850000>; >>> + regulator-max-microvolt = <1350000>; >>> + regulator-always-on; >>> + regulator-boot-on; >>> + op_mode = <3>; >>> + }; >>> + >>> + BUCK3 { >>> + regulator-name = "vdd_int"; >>> + regulator-min-microvolt = <900000>; >>> + regulator-max-microvolt = <1200000>; >>> + regulator-always-on; >>> + regulator-boot-on; >>> + op_mode = <3>; >>> + }; >>> + >>> + BUCK4 { >>> + regulator-name = "vdd_g3d"; >>> + regulator-min-microvolt = <850000>; >>> + regulator-max-microvolt = <1300000>; >>> + regulator-boot-on; >>> + op_mode = <3>; >>> + }; >>> + >>> + BUCK5 { >>> + regulator-name = "P1.8V_BUCK_OUT5"; >>> + regulator-min-microvolt = <1800000>; >>> + regulator-max-microvolt = <1800000>; >>> + regulator-always-on; >>> + regulator-boot-on; >>> + op_mode = <1>; >>> + }; >>> + >>> + BUCK6 { >>> + regulator-name = "P1.2V_BUCK_OUT6"; >>> + regulator-min-microvolt = <1200000>; >>> + regulator-max-microvolt = <1200000>; >>> + regulator-always-on; >>> + regulator-boot> >> > -on; >>> + op_mode = <0>; >>> + }; >>> + >>> + BUCK9 { >>> + regulator-name = "vdd_ummc"; >>> + regulator-min-microvolt = <950000>; >>> + regulator-max-microvolt = <3000000>; >>> + regulator-always-on; >>> + regulator-boot-on; >>> + op_mode = <3>; >>> + }; >>> + }; >>> + }; >>> + }; >>> + >>> + i2c at 12C70000 { >>> + trackpad { >>> + status = "disabled"; >> >> Having this bogus entry here doesn't add anything. Remove it until >> the trackpad should be added. See http://crbug.com/371114 for a >> slightly stale bug about trackpad. > > You misunderstand: This resolves an error about the cypress,cyapa > inherited from -cros-common.dtsi. Spring uses a different device and two > different I2C addresses. Ah, right. I forgot about cros5250-common. > Nodes named trackpad-bootloader and trackpad-alt are prepared here: > https://github.com/afaerber/linux/commits/spring-next It might work, but you run into pinctrl problems. You need to put the pinctrl node _somewhere_ and if you put it with the trackpad entries themselves then you get conflicts. ...and it doesn't belong in the i2c bus (though that's what we have locally in our tree) See <http://permalink.gmane.org/gmane.linux.kernel.samsung-soc/30953> for some background. >>> + }; >>> + }; >>> + >>> + i2c at 12CA0000 { >>> + embedded-controller { >> >> Add "cros_ec" alias like snow. >> >> >>> + compatible = "google,cros-ec-i2c"; >>> + reg = <0x1e>; >>> + interrupts = <6 0>; >>> + interrupt-parent = <&gpx1>; >>> + wakeup-source; >>> + >>> + keyboard-controller { >> >> Don't include keyboard-controller here. Add: >> >> #include "cros-ec-keyboard.dtsi" >> >> ...at the bottom. Note that I think that the spring EC has a special >> "charger" key that it uses to indicate when a charger was plugged in >> and unplugged. I'm not sure how that will end up getting supported >> upstream but you could just leave it out for now. > > Is there such a pending patch for snow? That's what I modeled after. Yeah, and it appears to be in linux-next. (1a395e3 ARM: dts: Use the cros-ec-keyboard fragment in exynos5250-snow). It actually ended up going through the tegra tree since it was in a series with a similar tegra change. I asked Kukjin to pick it up via merge but he didn't appear to. > Where is cros-ec-keyboard.dtsi? Don't see it in > http://git.kernel.org/cgit/linux/kernel/git/kgene/linux-samsung.git/tree/arch/arm/boot/dts?h=for-next > or > http://git.kernel.org/cgit/linux/kernel/git/kgene/linux-samsung.git/tree/include/dt-bindings?h=for-next > > Are you proposing I factor it out? > >>> + compatible = "google,cros-ec-keyb"; >>> + keypad,num-rows = <8>; >>> + keypad,num-columns = <13>; >> >> Don't you need pinctrl here? > > The keyboard is usable; what would pinctrl be needed for? There's none > in the 3.8 device tree. Generally it's good to have the pinctrl listed to configure the IRQ properly (get the pulls right). It might work without it but it's a little less ideal I think. I see this, right? pinctrl-names = "default"; pinctrl-0 = <&ec_irq>; ...in the downstream "arch/arm/boot/dts/exynos5250-spring.dts" >>> + google,needs-ghost-filter; >>> + linux,keymap = < >>> + 0x0001007d /* L_META */ >>> + 0x0002003b /* F1 */ >>> + 0x00030030 /* B */ >>> + 0x00040044 /* F10 */ >>> + 0x00060031 /* N */ >>> + 0x0008000d /* = */ >>> + 0x000a0064 /* R_ALT */ >>> + >>> + 0x01010001 /* ESC */ >>> + 0x0102003e /* F4 */ >>> + 0x01030022 /* G */ >>> + 0x01040041 /* F7 */ >>> + 0x01060023 /* H */ >>> + 0x01080028 /* ' */ >>> + 0x01090043 /* F9 */ >>> + 0x010b000e /* BKSPACE */ >>> + >>> + 0x0200001d /* L_CTRL */ >>> + 0x0201000f /* TAB */ >>> + 0x0202003d /* F3 */ >>> + 0x02030014 /* T */ >>> + 0x02040040 /* F6 */ >>> + 0x0205001b /* ] */ >>> + 0x02060015 /* Y */ >>> + 0x02070056 /* 102ND */ >>> + 0x0208001a /* [ */ >>> + 0x02090042 /* F8 */ >>> + >>> + 0x03010029 /* GRAVE */ >>> + 0x0302003c /* F2 */ >>> + 0x03030006 /* 5 */ >>> + 0x0304003f /* F5 */ >>> + 0x03060007 /* 6 */ >>> + 0x0308000c /* - */ >>> + 0x030b002b /* \ */ >>> + >>> + 0x04000061 /* R_CTRL */ >>> + 0x0401001e /* A */ >>> + 0x04020020 /* D */ >>> + 0x04030021 /* F */ >>> + 0x0404001f /* S */ >>> + 0x04050025 /* K */ >>> + 0x04060024 /* J */ >>> + 0x04080027 /* ; */ >>> + 0x04090026 /* L */ >>> + 0x040a002b /* \ */ >>> + 0x040b001c /* ENTER */ >>> + >>> + 0x0501002c /* Z */ >>> + 0x0502002e /* C */ >>> + 0x0503002f /* V */ >>> + 0x0504002d /* X */ >>> + 0x05050033 /* , */ >>> + 0x05060032 /* M */ >>> + 0x0507002a /* L_SHIFT */ >>> + 0x05080035 /* / */ >>> + 0x05090034 /* . */ >>> + 0x050B0039 /* SPACE */ >>> + >>> + 0x06010002 /* 1 */ >>> + 0x06020004 /* 3 */ >>> + 0x06030005 /* 4 */ >>> + 0x06040003 /* 2 */ >>> + 0x06050009 /* 8 */ >>> + 0x06060008 /* 7 */ >>> + 0x0608000b /* 0 */ >>> + 0x0609000a /* 9 */ >>> + 0x060a0038 /* L_ALT */ >>> + 0x060b006c /* DOWN */ >>> + 0x060c006a /* RIGHT */ >>> + >>> + 0x07010010 /* Q */ >>> + 0x07020012 /* E */ >>> + 0x07030013 /* R */ >>> + 0x07040011 /* W */ >>> + 0x07050017 /* I */ >>> + 0x07060016 /* U */ >>> + 0x07070036 /* R_SHIFT */ >>> + 0x07080019 /* P */ >>> + 0x07090018 /* O */ >>> + 0x070b0067 /* UP */ >>> + 0x070c0069 /* LEFT */ >>> + >; >>> + }; >>> + }; >>> + >>> + power-regulator { >>> + compatible = "ti,tps65090"; >> >> I doubt tps65090 will "just work". Does it? > > Good question. How to tell? :) Not familiar with clocks and regulators. > I don't see the nodes referenced anywhere, so I could just try to drop > (as I would, as per my cover letter, propose for anything non-essential > that turns controversial). What does "dmesg | grep tps65090" say? What does this show: grep "" /sys/class/regulator/*/name > If we drop tps65090, can we safely drop vbat-fixed-regulator as well? Yes >> On spring the tps65090 is not directly on the same i2c bus as the EC. >> It's actually hidden behind the EC. >> >> Locally in the ChromeOS tree there appears to be a forked copy of the >> 65090 regulator driver that's in use just for spring. See this from >> the ChromeOS 3.8 tree: >> >> ./drivers/regulator/tps65090-regulator.c >> ./drivers/regulator/cros_ec-tps65090.c >> >> The Spring version of the driver sends EC commands directly to access >> the tps65090. >> >> It is possible (untested) that you could also talk to tps65090 over an >> i2c tunnel. On exynos5420-peach-pit we have a full fledged i2c >> tunnel, but you may be able to extend the tunnel to export an i2c >> tunnel for spring using something like >> <https://chromium-review.googlesource.com/66116> > > The SBS battery thingy (not in this patch) should also be behind some > tunnel. There's none defined in -cros-common.dtsi or in my patch, and > still it shows up in dmesg to my surprise, complaining "Couldn't read > remote-bus property". Might be due to the cros5250-common. ...but yes, the battery should be behind the tunnel too and the patches needed for Spring haven't been posted by anyone yet. I picked up a whole bunch of cros_ec cleanup patches and thought that the tunnel patches for spring could possible go up after those land. >>> + reg = <0x48>; >>> + >>> + /* >>> + * Config irq to disable internal pulls >>> + * even though we run in polling mode. >>> + */ >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&tps65090_irq>; >>> + >>> + vsys1-supply = <&vbat>; >>> + vsys2-supply = <&vbat>; >>> + vsys3-supply = <&vbat>; >>> + infet1-supply = <&vbat>; >>> + infet2-supply = <&vbat>; >>> + infet3-supply = <&vbat>; >>> + infet4-supply = <&vbat>; >>> + infet5-supply = <&vbat>; >>> + infet6-supply = <&vbat>; >>> + infet7-supply = <&vbat>; >>> + vsys-l1-supply = <&vbat>; >>> + vsys-l2-supply = <&vbat>; >>> + >>> + regulators { >>> + fet1 { >>> + regulator-name = "vcd_led"; >>> + regulator-min-microvolt = <12000000>; >>> + regulator-max-microvolt = <12000000>; >>> + }; >>> + fet3 { >>> + regulator-name = "wwan_r"; >>> + regulator-min-microvolt = <3300000>; >>> + regulator-max-microvolt = <3300000>; >>> + regulator-always-on; >>> + }; >>> + fet5 { >>> + regulator-name = "cam"; >>> + regulator-min-microvolt = <3300000>; >>> + regulator-max-microvolt = <3300000>; >>> + regulator-always-on; >>> + }; >>> + fet6 { >>> + regulator-name = "lcd_vdd"; >>> + regulator-min-microvolt = <3300000>; >>> + regulator-max-microvolt = <3300000>; >>> + }; >>> + fet7 { >>> + regulator-name = "ts"; >>> + regulator-min-microvolt = <5000000>; >>> + regulator-max-microvolt = <5000000>; >>> + }; >>> + }; >>> + >>> + charger { >>> + compatible = "ti,tps65090-charger"; >>> + }; >>> + }; >>> + }; >>> + >>> + hdmi { >>> + hdmi-en-supply = <&s5m_ldo8_reg>; >>> + vdd-supply = <&s5m_ldo8_reg>; >>> + vdd_osc-supply = <&s5m_ldo10_reg>; >>> + vdd_pll-supply = <&s5m_ldo8_reg>; >>> + }; >>> + >>> + fimd at 14400000 { >>> + status = "okay"; >>> + samsung,invert-vclk; >>> + }; >>> + >>> + dp-controller at 145B0000 { >>> + status = "okay"; >>> + pinctrl-names = "default"; >>> + pinctrl-0 = <&dp_hpd>; >> >> This is probably not right. It looks as if spring uses gpc3-0 for >> display port HPD (as a GPIO). The upstream has this in the >> exynos5250-pinctrl.dtsi as a different pin. >> >> I think you'll need to define your own pinctrl here. >> >> >>> + samsung,color-space = <0>; >>> + samsung,dynamic-range = <0>; >>> + samsung,ycbcr-coeff = <0>; >>> + samsung,color-depth = <1>; >>> + samsung,link-rate = <0x0a>; >>> + samsung,lane-count = <1>; >>> + samsung,hpd-gpio = <&gpc3 0 0>; >>> + >>> + display-timings { >>> + native-mode = <&timing1>; >>> + >>> + timing1: timing at 1 { >>> + clock-frequency = <70589280>; >>> + hactive = <1366>; >>> + vactive = <768>; >>> + hfront-porch = <40>; >>> + hback-porch = <40>; >>> + hsync-len = <32>; >>> + vback-porch = <10>; >>> + vfront-porch = <12>; >>> + vsync-len = <6>; >>> + }; >>> + }; >>> + }; >>> + >>> + fixed-rate-clocks { >>> + xxti { >>> + compatible = "samsung,clock-xxti"; >>> + clock-frequency = <24000000>; >>> + }; >>> + }; >>> +}; > > Will check on the other suggestions. -Doug ^ permalink raw reply [flat|nested] 7+ messages in thread
* [RFC 4/4] ARM: dts: exynos5250: Add Spring device tree 2014-06-24 4:05 ` Doug Anderson @ 2014-06-24 10:06 ` Javier Martinez Canillas 2014-06-24 15:20 ` Doug Anderson 2014-06-24 15:06 ` Vincent Palatin 1 sibling, 1 reply; 7+ messages in thread From: Javier Martinez Canillas @ 2014-06-24 10:06 UTC (permalink / raw) To: linux-arm-kernel Hello Doug, On 06/24/2014 06:05 AM, Doug Anderson wrote: > Andreas, > > On Mon, Jun 23, 2014 at 3:46 PM, Andreas F?rber <afaerber@suse.de> wrote: >> Hi Doug, >> >> Am 23.06.2014 21:47, schrieb Doug Anderson: >>> Thanks for posting! A first pass on this is below... >> >> Thanks a lot for your quick review! My first big .dts patch, and no >> datasheets for the hardware at hand as a user. >> >> A first pass of replies to my defense. ;) >> >>> On Sun, Jun 22, 2014 at 6:21 PM, Andreas F?rber <afaerber@suse.de> wrote: >> [...] >>>> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts >>>> new file mode 100644 >>>> index 0000000..e857d44 >>>> --- /dev/null >>>> +++ b/arch/arm/boot/dts/exynos5250-spring.dts >>>> @@ -0,0 +1,556 @@ >>>> +/* >>>> + * Google Spring board device tree source >>>> + * >>>> + * Copyright (c) 2013 Google, Inc >>>> + * Copyright (c) 2014 SUSE LINUX Products GmbH >>>> + * >>>> + * This program is free software; you can redistribute it and/or modify >>>> + * it under the terms of the GNU General Public License version 2 as >>>> + * published by the Free Software Foundation. >>>> + */ >>>> + >>>> +/dts-v1/; >>>> +#include "exynos5250.dtsi" >>>> +#include "exynos5250-cros-common.dtsi" >>> >>> It is possible we may want to backpedal on the use of >>> "exynos5250-cros-common.dtsi". I know that Olof (now CCed) said he >>> wasn't a fan of how it turned out. >>> >>> The original idea was that it should include the arbitrary set of >>> things that are common between a chunk of Chrome OS boards. As more >>> boards were introduced things would need to migrate from the "common" >>> file to the board files. >>> >>> At the moment the current conventional wisdom is that some duplication >>> is better than the confusing movement of everything back and forth. >>> See exynos5420-peach-pit and exynos5800-peach-pi in ToT linux-next. >>> >>> Another option is to identify DTS fragments that are common across boards and create .dtsi files for these specific chunks instead of trying to group all set of common things on a single .dtsi file. For example, a quite common design for OMAP2+ based boards is to use a SMSC LAN chip connected to OMAP's General-Purpose Memory Controller (GPMC). So the following files were created to reduce DTS duplication: arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi arch/arm/boot/dts/omap-gpmc-smsc9221.dtsi Now that I think about it, is the same that what you did for arm/boot/dts/cros-ec-keyboard.dtsi. Maybe splitting exynos5250-cros-common.dtsi in a set of .dtsi files will make it more flexible/reusable? >>>> +/ { >>>> + model = "Google Spring"; >>>> + compatible = "google,spring", "samsung,exynos5250", "samsung,exynos5"; >>>> + >>>> + pinctrl at 11400000 { >>> >>> The new best way to do things is to put this down at the bottom. See >>> exynos5420-peach-pit as an example: >>> >>> &pinctrl_0 { >>> ... >>> } >>> >>> Note that I believe it was decided that top-level references like that >>> should be sorted alphabetically. >> >> Thanks for the hint. (My chosen sort order here was by address.) >> >>> If you wanted to apply that run to exynos5250-snow I don't think it >>> would be a terrible idea. >> >> I can of course apply changes to Snow, but I cannot test them myself. > > If you want to send up a patch like that I'm happy to give it a once > over and also to test it. ...but don't feel obligated > > >>>> + s5m8767_dvs: s5m8767-dvs { >>>> + samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2"; >>>> + samsung,pin-function = <0>; >>>> + samsung,pin-pud = <1>; >>>> + samsung,pin-drv = <0>; >>>> + }; >>>> + >>>> + s5m8767_ds: s5m8767-ds { >>>> + samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5"; >>>> + samsung,pin-function = <0>; >>>> + samsung,pin-pud = <1>; >>>> + samsung,pin-drv = <0>; >>>> + }; >>>> + >>>> + tps65090_irq: tps65090-irq { >>>> + samsung,pins = "gpx2-6"; >>>> + samsung,pin-function = <0>; >>>> + samsung,pin-pud = <0>; >>>> + samsung,pin-drv = <0>; >>>> + }; >>>> + >>>> + s5m8767_irq: s5m8767-irq { >>>> + samsung,pins = "gpx3-2"; >>>> + samsung,pin-function = <0>; >>>> + samsung,pin-pud = <0>; >>>> + samsung,pin-drv = <0>; >>>> + }; >>>> + >>>> + hdmi_hpd_irq: hdmi-hpd-irq { >>>> + samsung,pins = "gpx3-7"; >>>> + samsung,pin-function = <0>; >>>> + samsung,pin-pud = <1>; >>>> + samsung,pin-drv = <0>; >>>> + }; >>>> + }; >>>> + >>>> + pinctrl at 13400000 { >>>> + hsic_reset: hsic-reset { >>>> + samsung,pins = "gpe1-0"; >>>> + samsung,pin-function = <1>; >>>> + samsung,pin-pud = <0>; >>>> + samsung,pin-drv = <0>; >>>> + }; >>> >>> I'm pretty sure that the HSIC reset needed some funky code to make it >>> work and I'm not sure what the status of that is upstream >> >> Yeah, you mentioned something along those lines. However it's the >> equivalent of the usb3-vbus-en in -snow.dts. Rename or drop? > > On snow locally I see USB2 vbus is gpx1-1 and USB3 vbus is gpx2-7. I > don't see that in spring. > > This will take more time than I have right now to track down. I added > Julius to the thread in case he has time to answer and can suggest > what to do for upstream purposes. I may be able to look more > tomorrow. > > You can always send up the next version and include this and we'll > look at it again. > > >>>> + }; >>>> + >>>> + vbat: vbat-fixed-regulator { >>>> + compatible = "regulator-fixed"; >>>> + regulator-name = "vbat-supply"; >>>> + regulator-boot-on; >>>> + }; >>>> + >>>> + usb at 12000000 { >>>> + status = "okay"; >>>> + }; >>>> + >>>> + usb3_vbus_reg: regulator-usb3 { >>>> + compatible = "regulator-fixed"; >>>> + regulator-name = "P5.0V_USB3CON"; >>>> + regulator-min-microvolt = <5000000>; >>>> + regulator-max-microvolt = <5000000>; >>>> + gpio = <&gpe1 0 1>; >>>> + pinctrl-names = "default"; >>>> + pinctrl-0 = <&hsic_reset>; >>>> + enable-active-high; >>>> + }; >>>> + >>>> + phy at 12100000 { >>>> + vbus-supply = <&usb3_vbus_reg>; >>>> + }; >>>> + >>>> + usb at 12110000 { >>>> + samsung,vbus-gpio = <&gpx1 1 0>; >>>> + status = "okay"; >>>> + }; >>>> + >>>> + usb at 12120000 { >>>> + status = "okay"; >>>> + }; >>>> + >>>> + mmc at 12220000 { >>>> + /* MMC2 pins are used as GPIO for eDP bridge control. */ >>>> + status = "disabled"; >>>> + }; >>>> + >>>> + mmc at 12230000 { >>>> + status = "disabled"; >>>> + }; >>>> + >>>> + i2c at 12C60000 { >>>> + max77686 at 09 { >>> >>> There is no max77686 on spring. It uses s5m8767 in the place of max77686. >>> >>> ...you've got "status = disabled", just remove it. >> >> That's because it's inherited from exynos5250-cros-common.dtsi. > > Ah, right. So if we're keeping cros-common the proper thing to do is > to move it out of cros-common in a patch before this one. ...but I > think people might be happier if you simply don't include cros-common. > > >> The rtc that the system successfully uses is "s5m-rtc", which I guess is >> on the s5m8767 then? (Confusing that 3.8 Spring had this rtc node >> despite Snow's max77686 not having it.) > > I think it's not really supposed to. It was a bit of a hack to handle > the fact that the RTC has two different i2c addresses on both the > 77686 and this PMIC. The max77686 driver upstream handles it all in > code and doesn't ask the device tree to list both addresses. > > I think that _upstream_ snow doesn't have the node but _downstream_ > spring might have the node (though having a child of a disabled node > isn't particularly useful). > > Personally I think that "status = [enabled | disabled]" only makes sense for IP blocks that are part of the SoC but may or may not be used by a board (e.g: i2c and spi buses, sdhci and usb host controllers, etc). DTS should be a description of the hardware so I agree that having a disabled node for a device that is not present in the board is not right. >>>> + #address-cells = <1>; >>>> + #size-cells = <0>; >>>> + status = "disabled"; >>>> + >>>> + rtc { >>>> + reg = <0x6>; >>>> + }; >>>> + }; >>>> + >>>> + s5m8767_pmic at 66 { >>>> + compatible = "samsung,s5m8767-pmic"; >>>> + reg = <0x66>; >>>> + interrupt-parent = <&gpx3>; >>>> + interrupts = <2 0>; >>>> + pinctrl-names = "default"; >>>> + pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>; >>>> + wakeup-source; >>>> + >>>> + s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 1>, /* DVS1 */ >>>> + <&gpd1 1 1>, /* DVS2 */ >>>> + <&gpd1 2 1>; /* DVS3 */ >>>> + >>>> + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1>, /* SET1 */ >>>> + <&gpx2 4 1>, /* SET2 */ >>>> + <&gpx2 5 1>; /* SET3 */ >>> >>> The final "1" in each of the GPIO specifiers above should be GPIO_ACTIVE_LOW. >>> >>> >>>> + >>>> + /* >>>> + * The following arrays of DVS voltages are not used, since we are >>>> + * not using GPIOs to control PMIC bucks, but they must be defined >>>> + * to please the driver. >>>> + */ >>>> + s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, >>>> + <1250000>, <1200000>, >>>> + <1150000>, <1100000>, >>>> + <1000000>, <950000>; >>>> + >>>> + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, >>>> + <1100000>, <1100000>, >>>> + <1000000>, <1000000>, >>>> + <1000000>, <1000000>; >>>> + >>>> + s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, >>>> + <1200000>, <1200000>, >>>> + <1200000>, <1200000>, >>>> + <1200000>, <1200000>; >>>> + >>>> + clocks { >>>> + compatible = "samsung,s5m8767-clk"; >>>> + #clock-cells = <1>; >>>> + clock-output-names = "en32khz_ap", >>>> + "en32khz_cp", >>>> + "en32khz_bt"; >>>> + }; >>>> + >>>> + regulators { >>>> + s5m_ldo4_reg: LDO4 { >>>> + regulator-name = "P1.0V_LDO_OUT4"; >>>> + regulator-min-microvolt = <1000000>; >>>> + regulator-max-microvolt = <1000000>; >>>> + regulator-always-on; >>>> + op_mode = <0>; >>> >>> I think that "op_mode" here is questionable. Adding Javier to the >>> thread who was looking at this for max77802 and possibly max77686. >> >> Confirming that this op_mode is present in the original 3.8 device tree. > > Yes and it needs to be handled eventually. It makes suspend/resume > work properly. ...but I think it needs to be thought out better. > > ...but given that other users of this PMIC have it I guess it makes > sense to leave it in. Javier was going to try to think it through > better for max77686 and max77802. > > The op_mode property is supported in mainline for this driver. I think that is not a great binding tbh since the property has a generic name while it's specific to the s5m8767 PMIC. But the driver uses it so makes sense to have it in the DTS. I've on my TODO list after the Max 77802 PMIC driver is merged to propose a property for the generic regulator binding along the lines of what you proposed in [0]. If a generic property is added to the regulator binding, the exynos5250-spring.dts can later be changed to use this new property or keep using the s5m8767 specific one since the driver has to keep supporting it for backward compatibility. >> (I used dtc to compile my /proc/device-tree tarball back to .dts, so it >> has hexadecimal <0x0> but that shouldn't matter to dtc AFAIU.) >> >>>> + }; >>>> + >>>> + s5m_ldo5_reg: LDO5 { >>>> + regulator-name = "P1.0V_LDO_OUT5"; >>>> + regulator-min-microvolt = <1000000>; >>>> + regulator-max-microvolt = <1000000>; >>>> + regulator-always-on; >>>> + op_mode = <0>; >>>> + }; >>>> + >>>> + s5m_ldo6_reg: LDO6 { >>>> + regulator-name = "vdd_mydp"; >>>> + regulator-min-microvolt = <1000000>; >>>> + regulator-max-microvolt = <1000000>; >>>> + regulator-always-on; >>>> + op_mode = <3>; >>>> + }; >>>> + >>>> + s5m_ldo7_reg: LDO7 { >>>> + regulator-name = "P1.1V_LDO_OUT7"; >>>> + regulator-min-microvolt = <1100000>; >>>> + regulator-max-microvolt = <1100000>; >>>> + regulator-always-on; >>>> + op_mode = <3>; >>>> + }; >>>> + >>>> + s5m_ldo8_reg: LDO8 { >>>> + regulator-name = "P1.0V_LDO_OUT8"; >>>> + regulator-min-microvolt = <1000000>; >>>> + regulator-max-microvolt = <1000000>; >>>> + regulator-always-on; >>>> + op_mode = <3>; >>>> + }; >>>> + >>>> + s5m_ldo10_reg: LDO10 { >>>> + regulator-name = "P1.8V_LDO_OUT10"; >>>> + regulator-min-microvolt = <1800000>; >>>> + regulator-max-microvolt = <1800000>; >>>> + regulator-always-on; >>>> + op_mode = <3>; >>>> + }; >>>> + >>>> + s5m_ldo11_reg: LDO11 { >>>> + regulator-name = "P1.8V_LDO_OUT11"; >>>> + regulator-min-microvolt = <1800000>; >>>> + regulator-max-microvolt = <1800000>; >>>> + regulator-always-on; >>>> + op_mode = <0>; >>>> + }; >>>> + >>>> + s5m_ldo12_reg: LDO12 { >>>> + regulator-name = "P3.0V_LDO_OUT12"; >>>> + regulator-min-microvolt = <3000000>; >>>> + regulator-max-microvolt = <3000000>; >>>> + regulator-always-on; >>>> + op_mode = <3>; >>>> + }; >>>> + >>>> + s5m_ldo13_reg: LDO13 { >>>> + regulator-name = "P1.8V_LDO_OUT13"; >>>> + regulator-min-microvolt = <1800000>; >>>> + regulator-max-microvolt = <1800000>; >>>> + regulator-always-on; >>>> + op_mode = <0>; >>>> + }; >>>> + >>>> + s5m_ldo14_reg: LDO14 { >>>> + regulator-name = "P1.8V_LDO_OUT14"; >>>> + regulator-min-microvolt = <1800000>; >>>> + regulator-max-microvolt = <1800000>; >>>> + regulator-always-on; >>>> + op_mode = <3>; >>>> + }; >>>> + >>>> + s5m_ldo15_reg: LDO15 { >>>> + regulator-name = "P1.0V_LDO_OUT15"; >>>> + regulator-min-microvolt = <1000000>; >>>> + regulator-max-microvolt = <1000000>; >>>> + regulator-always-on; >>>> + op_mode = <3>; >>>> + }; >>>> + >>>> + s5m_ldo16_reg: LDO16 { >>>> + regulator-name = "P1.8V_LDO_OUT16"; >>>> + regulator-min-microvolt = <1800000>; >>>> + regulator-max-microvolt = <1800000>; >>>> + regulator-always-on; >>>> + op_mode = <3>; >>>> + }; >>>> + >>>> + s5m_ldo17_reg: LDO17 { >>>> + regulator-name = "P2.8V_LDO_OUT17"; >>>> + regulator-min-microvolt = <2800000>; >>>> + regulator-max-microvolt = <2800000>; >>>> + regulator-always-on; >>>> + op_mode = <0>; >>>> + }; >>>> + >>>> + s5m_ldo25_reg: LDO25 { >>>> + regulator-name = "vdd_bridge"; >>>> + regulator-min-microvolt = <1200000>; >>>> + regulator-max-microvolt = <1200000>; >>>> + regulator-always-on; >>>> + op_mode = <1>; >>>> + }; >>>> + >>>> + BUCK1 { >>>> + regulator-name = "vdd_mif"; >>>> + regulator-min-microvolt = <950000>; >>>> + regulator-max-microvolt = <1300000>; >>>> + regulator-always-on; >>>> + regulator-boot-on; >>>> + op_mode = <3>; >>>> + }; >>>> + >>>> + BUCK2 { >>>> + regulator-name = "vdd_arm"; >>>> + regulator-min-microvolt = <850000>; >>>> + regulator-max-microvolt = <1350000>; >>>> + regulator-always-on; >>>> + regulator-boot-on; >>>> + op_mode = <3>; >>>> + }; >>>> + >>>> + BUCK3 { >>>> + regulator-name = "vdd_int"; >>>> + regulator-min-microvolt = <900000>; >>>> + regulator-max-microvolt = <1200000>; >>>> + regulator-always-on; >>>> + regulator-boot-on; >>>> + op_mode = <3>; >>>> + }; >>>> + >>>> + BUCK4 { >>>> + regulator-name = "vdd_g3d"; >>>> + regulator-min-microvolt = <850000>; >>>> + regulator-max-microvolt = <1300000>; >>>> + regulator-boot-on; >>>> + op_mode = <3>; >>>> + }; >>>> + >>>> + BUCK5 { >>>> + regulator-name = "P1.8V_BUCK_OUT5"; >>>> + regulator-min-microvolt = <1800000>; >>>> + regulator-max-microvolt = <1800000>; >>>> + regulator-always-on; >>>> + regulator-boot-on; >>>> + op_mode = <1>; >>>> + }; >>>> + >>>> + BUCK6 { >>>> + regulator-name = "P1.2V_BUCK_OUT6"; >>>> + regulator-min-microvolt = <1200000>; >>>> + regulator-max-microvolt = <1200000>; >>>> + regulator-always-on; >>>> + regulator-boot> >>> >> -on; >>>> + op_mode = <0>; >>>> + }; >>>> + >>>> + BUCK9 { >>>> + regulator-name = "vdd_ummc"; >>>> + regulator-min-microvolt = <950000>; >>>> + regulator-max-microvolt = <3000000>; >>>> + regulator-always-on; >>>> + regulator-boot-on; >>>> + op_mode = <3>; >>>> + }; >>>> + }; >>>> + }; >>>> + }; >>>> + >>>> + i2c at 12C70000 { >>>> + trackpad { >>>> + status = "disabled"; >>> >>> Having this bogus entry here doesn't add anything. Remove it until >>> the trackpad should be added. See http://crbug.com/371114 for a >>> slightly stale bug about trackpad. >> >> You misunderstand: This resolves an error about the cypress,cyapa >> inherited from -cros-common.dtsi. Spring uses a different device and two >> different I2C addresses. > > Ah, right. I forgot about cros5250-common. > > >> Nodes named trackpad-bootloader and trackpad-alt are prepared here: >> https://github.com/afaerber/linux/commits/spring-next > > It might work, but you run into pinctrl problems. You need to put the > pinctrl node _somewhere_ and if you put it with the trackpad entries > themselves then you get conflicts. ...and it doesn't belong in the > i2c bus (though that's what we have locally in our tree) > > See <http://permalink.gmane.org/gmane.linux.kernel.samsung-soc/30953> > for some background. > > >>>> + }; >>>> + }; >>>> + >>>> + i2c at 12CA0000 { >>>> + embedded-controller { >>> >>> Add "cros_ec" alias like snow. >>> >>> >>>> + compatible = "google,cros-ec-i2c"; >>>> + reg = <0x1e>; >>>> + interrupts = <6 0>; >>>> + interrupt-parent = <&gpx1>; >>>> + wakeup-source; >>>> + >>>> + keyboard-controller { >>> >>> Don't include keyboard-controller here. Add: >>> >>> #include "cros-ec-keyboard.dtsi" >>> >>> ...at the bottom. Note that I think that the spring EC has a special >>> "charger" key that it uses to indicate when a charger was plugged in >>> and unplugged. I'm not sure how that will end up getting supported >>> upstream but you could just leave it out for now. >> >> Is there such a pending patch for snow? That's what I modeled after. > > Yeah, and it appears to be in linux-next. (1a395e3 ARM: dts: Use the > cros-ec-keyboard fragment in exynos5250-snow). It actually ended up > going through the tegra tree since it was in a series with a similar > tegra change. I asked Kukjin to pick it up via merge but he didn't > appear to. > > >> Where is cros-ec-keyboard.dtsi? Don't see it in >> http://git.kernel.org/cgit/linux/kernel/git/kgene/linux-samsung.git/tree/arch/arm/boot/dts?h=for-next >> or >> http://git.kernel.org/cgit/linux/kernel/git/kgene/linux-samsung.git/tree/include/dt-bindings?h=for-next >> >> Are you proposing I factor it out? >> >>>> + compatible = "google,cros-ec-keyb"; >>>> + keypad,num-rows = <8>; >>>> + keypad,num-columns = <13>; >>> >>> Don't you need pinctrl here? >> >> The keyboard is usable; what would pinctrl be needed for? There's none >> in the 3.8 device tree. > > Generally it's good to have the pinctrl listed to configure the IRQ > properly (get the pulls right). It might work without it but it's a > little less ideal I think. > > I see this, right? > > pinctrl-names = "default"; > pinctrl-0 = <&ec_irq>; > > ...in the downstream "arch/arm/boot/dts/exynos5250-spring.dts" > > >>>> + google,needs-ghost-filter; >>>> + linux,keymap = < >>>> + 0x0001007d /* L_META */ >>>> + 0x0002003b /* F1 */ >>>> + 0x00030030 /* B */ >>>> + 0x00040044 /* F10 */ >>>> + 0x00060031 /* N */ >>>> + 0x0008000d /* = */ >>>> + 0x000a0064 /* R_ALT */ >>>> + >>>> + 0x01010001 /* ESC */ >>>> + 0x0102003e /* F4 */ >>>> + 0x01030022 /* G */ >>>> + 0x01040041 /* F7 */ >>>> + 0x01060023 /* H */ >>>> + 0x01080028 /* ' */ >>>> + 0x01090043 /* F9 */ >>>> + 0x010b000e /* BKSPACE */ >>>> + >>>> + 0x0200001d /* L_CTRL */ >>>> + 0x0201000f /* TAB */ >>>> + 0x0202003d /* F3 */ >>>> + 0x02030014 /* T */ >>>> + 0x02040040 /* F6 */ >>>> + 0x0205001b /* ] */ >>>> + 0x02060015 /* Y */ >>>> + 0x02070056 /* 102ND */ >>>> + 0x0208001a /* [ */ >>>> + 0x02090042 /* F8 */ >>>> + >>>> + 0x03010029 /* GRAVE */ >>>> + 0x0302003c /* F2 */ >>>> + 0x03030006 /* 5 */ >>>> + 0x0304003f /* F5 */ >>>> + 0x03060007 /* 6 */ >>>> + 0x0308000c /* - */ >>>> + 0x030b002b /* \ */ >>>> + >>>> + 0x04000061 /* R_CTRL */ >>>> + 0x0401001e /* A */ >>>> + 0x04020020 /* D */ >>>> + 0x04030021 /* F */ >>>> + 0x0404001f /* S */ >>>> + 0x04050025 /* K */ >>>> + 0x04060024 /* J */ >>>> + 0x04080027 /* ; */ >>>> + 0x04090026 /* L */ >>>> + 0x040a002b /* \ */ >>>> + 0x040b001c /* ENTER */ >>>> + >>>> + 0x0501002c /* Z */ >>>> + 0x0502002e /* C */ >>>> + 0x0503002f /* V */ >>>> + 0x0504002d /* X */ >>>> + 0x05050033 /* , */ >>>> + 0x05060032 /* M */ >>>> + 0x0507002a /* L_SHIFT */ >>>> + 0x05080035 /* / */ >>>> + 0x05090034 /* . */ >>>> + 0x050B0039 /* SPACE */ >>>> + >>>> + 0x06010002 /* 1 */ >>>> + 0x06020004 /* 3 */ >>>> + 0x06030005 /* 4 */ >>>> + 0x06040003 /* 2 */ >>>> + 0x06050009 /* 8 */ >>>> + 0x06060008 /* 7 */ >>>> + 0x0608000b /* 0 */ >>>> + 0x0609000a /* 9 */ >>>> + 0x060a0038 /* L_ALT */ >>>> + 0x060b006c /* DOWN */ >>>> + 0x060c006a /* RIGHT */ >>>> + >>>> + 0x07010010 /* Q */ >>>> + 0x07020012 /* E */ >>>> + 0x07030013 /* R */ >>>> + 0x07040011 /* W */ >>>> + 0x07050017 /* I */ >>>> + 0x07060016 /* U */ >>>> + 0x07070036 /* R_SHIFT */ >>>> + 0x07080019 /* P */ >>>> + 0x07090018 /* O */ >>>> + 0x070b0067 /* UP */ >>>> + 0x070c0069 /* LEFT */ >>>> + >; >>>> + }; >>>> + }; >>>> + >>>> + power-regulator { >>>> + compatible = "ti,tps65090"; >>> >>> I doubt tps65090 will "just work". Does it? >> >> Good question. How to tell? :) Not familiar with clocks and regulators. >> I don't see the nodes referenced anywhere, so I could just try to drop >> (as I would, as per my cover letter, propose for anything non-essential >> that turns controversial). > > What does "dmesg | grep tps65090" say? > > What does this show: > grep "" /sys/class/regulator/*/name > > >> If we drop tps65090, can we safely drop vbat-fixed-regulator as well? > > Yes > > >>> On spring the tps65090 is not directly on the same i2c bus as the EC. >>> It's actually hidden behind the EC. >>> >>> Locally in the ChromeOS tree there appears to be a forked copy of the >>> 65090 regulator driver that's in use just for spring. See this from >>> the ChromeOS 3.8 tree: >>> >>> ./drivers/regulator/tps65090-regulator.c >>> ./drivers/regulator/cros_ec-tps65090.c >>> >>> The Spring version of the driver sends EC commands directly to access >>> the tps65090. >>> >>> It is possible (untested) that you could also talk to tps65090 over an >>> i2c tunnel. On exynos5420-peach-pit we have a full fledged i2c >>> tunnel, but you may be able to extend the tunnel to export an i2c >>> tunnel for spring using something like >>> <https://chromium-review.googlesource.com/66116> >> >> The SBS battery thingy (not in this patch) should also be behind some >> tunnel. There's none defined in -cros-common.dtsi or in my patch, and >> still it shows up in dmesg to my surprise, complaining "Couldn't read >> remote-bus property". > > Might be due to the cros5250-common. ...but yes, the battery should > be behind the tunnel too and the patches needed for Spring haven't > been posted by anyone yet. I picked up a whole bunch of cros_ec > cleanup patches and thought that the tunnel patches for spring could > possible go up after those land. > > >>>> + reg = <0x48>; >>>> + >>>> + /* >>>> + * Config irq to disable internal pulls >>>> + * even though we run in polling mode. >>>> + */ >>>> + pinctrl-names = "default"; >>>> + pinctrl-0 = <&tps65090_irq>; >>>> + >>>> + vsys1-supply = <&vbat>; >>>> + vsys2-supply = <&vbat>; >>>> + vsys3-supply = <&vbat>; >>>> + infet1-supply = <&vbat>; >>>> + infet2-supply = <&vbat>; >>>> + infet3-supply = <&vbat>; >>>> + infet4-supply = <&vbat>; >>>> + infet5-supply = <&vbat>; >>>> + infet6-supply = <&vbat>; >>>> + infet7-supply = <&vbat>; >>>> + vsys-l1-supply = <&vbat>; >>>> + vsys-l2-supply = <&vbat>; >>>> + >>>> + regulators { >>>> + fet1 { >>>> + regulator-name = "vcd_led"; >>>> + regulator-min-microvolt = <12000000>; >>>> + regulator-max-microvolt = <12000000>; >>>> + }; >>>> + fet3 { >>>> + regulator-name = "wwan_r"; >>>> + regulator-min-microvolt = <3300000>; >>>> + regulator-max-microvolt = <3300000>; >>>> + regulator-always-on; >>>> + }; >>>> + fet5 { >>>> + regulator-name = "cam"; >>>> + regulator-min-microvolt = <3300000>; >>>> + regulator-max-microvolt = <3300000>; >>>> + regulator-always-on; >>>> + }; >>>> + fet6 { >>>> + regulator-name = "lcd_vdd"; >>>> + regulator-min-microvolt = <3300000>; >>>> + regulator-max-microvolt = <3300000>; >>>> + }; >>>> + fet7 { >>>> + regulator-name = "ts"; >>>> + regulator-min-microvolt = <5000000>; >>>> + regulator-max-microvolt = <5000000>; >>>> + }; >>>> + }; >>>> + >>>> + charger { >>>> + compatible = "ti,tps65090-charger"; >>>> + }; >>>> + }; >>>> + }; >>>> + >>>> + hdmi { >>>> + hdmi-en-supply = <&s5m_ldo8_reg>; >>>> + vdd-supply = <&s5m_ldo8_reg>; >>>> + vdd_osc-supply = <&s5m_ldo10_reg>; >>>> + vdd_pll-supply = <&s5m_ldo8_reg>; >>>> + }; >>>> + >>>> + fimd at 14400000 { >>>> + status = "okay"; >>>> + samsung,invert-vclk; >>>> + }; >>>> + >>>> + dp-controller at 145B0000 { >>>> + status = "okay"; >>>> + pinctrl-names = "default"; >>>> + pinctrl-0 = <&dp_hpd>; >>> >>> This is probably not right. It looks as if spring uses gpc3-0 for >>> display port HPD (as a GPIO). The upstream has this in the >>> exynos5250-pinctrl.dtsi as a different pin. >>> >>> I think you'll need to define your own pinctrl here. >>> >>> >>>> + samsung,color-space = <0>; >>>> + samsung,dynamic-range = <0>; >>>> + samsung,ycbcr-coeff = <0>; >>>> + samsung,color-depth = <1>; >>>> + samsung,link-rate = <0x0a>; >>>> + samsung,lane-count = <1>; >>>> + samsung,hpd-gpio = <&gpc3 0 0>; >>>> + >>>> + display-timings { >>>> + native-mode = <&timing1>; >>>> + >>>> + timing1: timing at 1 { >>>> + clock-frequency = <70589280>; >>>> + hactive = <1366>; >>>> + vactive = <768>; >>>> + hfront-porch = <40>; >>>> + hback-porch = <40>; >>>> + hsync-len = <32>; >>>> + vback-porch = <10>; >>>> + vfront-porch = <12>; >>>> + vsync-len = <6>; >>>> + }; >>>> + }; >>>> + }; >>>> + >>>> + fixed-rate-clocks { >>>> + xxti { >>>> + compatible = "samsung,clock-xxti"; >>>> + clock-frequency = <24000000>; >>>> + }; >>>> + }; >>>> +}; >> >> Will check on the other suggestions. > > -Doug > Best regards, Javier [0]: https://patchwork.kernel.org/patch/1855331/ ^ permalink raw reply [flat|nested] 7+ messages in thread
* [RFC 4/4] ARM: dts: exynos5250: Add Spring device tree 2014-06-24 10:06 ` Javier Martinez Canillas @ 2014-06-24 15:20 ` Doug Anderson 0 siblings, 0 replies; 7+ messages in thread From: Doug Anderson @ 2014-06-24 15:20 UTC (permalink / raw) To: linux-arm-kernel Javier, On Tue, Jun 24, 2014 at 3:06 AM, Javier Martinez Canillas <javier.martinez@collabora.co.uk> wrote: > Hello Doug, > > On 06/24/2014 06:05 AM, Doug Anderson wrote: > Another option is to identify DTS fragments that are common across boards and > create .dtsi files for these specific chunks instead of trying to group all set > of common things on a single .dtsi file. > > For example, a quite common design for OMAP2+ based boards is to use a SMSC LAN > chip connected to OMAP's General-Purpose Memory Controller (GPMC). So the > following files were created to reduce DTS duplication: > > arch/arm/boot/dts/omap-gpmc-smsc911x.dtsi > arch/arm/boot/dts/omap-gpmc-smsc9221.dtsi > > Now that I think about it, is the same that what you did for > arm/boot/dts/cros-ec-keyboard.dtsi. > > Maybe splitting exynos5250-cros-common.dtsi in a set of .dtsi files will make it > more flexible/reusable? Yes, I think the config fragments can be cleaner but I think we have to be judicious about using them. There are definitely tradeoffs involved. The keyboard was such an excessively large thing and totally duplicated, so moving it out made sense. Other bits are less obvious (to me) because there are so many interactions / combinations and you end up with a bit of spaghetti in terms of which labels are used by and provided by each fragment. I guess possibly you could codify that better... A few thoughts looking at exynos5420-peach-pit: * backlight: seems (?) too board specific * samsung,exynos5420-oscclk: could totally be a fragment, but very small. * power key: could be a fragment for all boards that happen to use gpx1-2 for this * sound: could be a fragment for all devices using "google,snow-audio-max98090", possibly. > Personally I think that "status = [enabled | disabled]" only makes sense for IP > blocks that are part of the SoC but may or may not be used by a board (e.g: i2c > and spi buses, sdhci and usb host controllers, etc). > > DTS should be a description of the hardware so I agree that having a disabled > node for a device that is not present in the board is not right. Right. We'll take a look again in v2 when cros-common isn't used. I think this could go in steps: 1. Don't use cros-common for spring 2. Don't use cros-common for snow (fold stuff in) 3. Introduce some fragments. ^ permalink raw reply [flat|nested] 7+ messages in thread
* [RFC 4/4] ARM: dts: exynos5250: Add Spring device tree 2014-06-24 4:05 ` Doug Anderson 2014-06-24 10:06 ` Javier Martinez Canillas @ 2014-06-24 15:06 ` Vincent Palatin 1 sibling, 0 replies; 7+ messages in thread From: Vincent Palatin @ 2014-06-24 15:06 UTC (permalink / raw) To: linux-arm-kernel Re-sending ... the text-only encoding was not properly turned on on the previous one and irritated the mailing lists. On Mon, Jun 23, 2014 at 9:05 PM, Doug Anderson <dianders@chromium.org> wrote: > > Andreas, > > On Mon, Jun 23, 2014 at 3:46 PM, Andreas F?rber <afaerber@suse.de> wrote: > > Hi Doug, > > > > Am 23.06.2014 21:47, schrieb Doug Anderson: > >> Thanks for posting! A first pass on this is below... > > > > Thanks a lot for your quick review! My first big .dts patch, and no > > datasheets for the hardware at hand as a user. > > > > A first pass of replies to my defense. ;) > > > >> On Sun, Jun 22, 2014 at 6:21 PM, Andreas F?rber <afaerber@suse.de> wrote: > > [...] > >>> diff --git a/arch/arm/boot/dts/exynos5250-spring.dts b/arch/arm/boot/dts/exynos5250-spring.dts > >>> new file mode 100644 > >>> index 0000000..e857d44 > >>> --- /dev/null > >>> +++ b/arch/arm/boot/dts/exynos5250-spring.dts > >>> @@ -0,0 +1,556 @@ > >>> +/* > >>> + * Google Spring board device tree source > >>> + * > >>> + * Copyright (c) 2013 Google, Inc > >>> + * Copyright (c) 2014 SUSE LINUX Products GmbH > >>> + * > >>> + * This program is free software; you can redistribute it and/or modify > >>> + * it under the terms of the GNU General Public License version 2 as > >>> + * published by the Free Software Foundation. > >>> + */ > >>> + > >>> +/dts-v1/; > >>> +#include "exynos5250.dtsi" > >>> +#include "exynos5250-cros-common.dtsi" > >> > >> It is possible we may want to backpedal on the use of > >> "exynos5250-cros-common.dtsi". I know that Olof (now CCed) said he > >> wasn't a fan of how it turned out. > >> > >> The original idea was that it should include the arbitrary set of > >> things that are common between a chunk of Chrome OS boards. As more > >> boards were introduced things would need to migrate from the "common" > >> file to the board files. > >> > >> At the moment the current conventional wisdom is that some duplication > >> is better than the confusing movement of everything back and forth. > >> See exynos5420-peach-pit and exynos5800-peach-pi in ToT linux-next. > >> > >> > >>> +/ { > >>> + model = "Google Spring"; > >>> + compatible = "google,spring", "samsung,exynos5250", "samsung,exynos5"; > >>> + > >>> + pinctrl at 11400000 { > >> > >> The new best way to do things is to put this down at the bottom. See > >> exynos5420-peach-pit as an example: > >> > >> &pinctrl_0 { > >> ... > >> } > >> > >> Note that I believe it was decided that top-level references like that > >> should be sorted alphabetically. > > > > Thanks for the hint. (My chosen sort order here was by address.) > > > >> If you wanted to apply that run to exynos5250-snow I don't think it > >> would be a terrible idea. > > > > I can of course apply changes to Snow, but I cannot test them myself. > > If you want to send up a patch like that I'm happy to give it a once > over and also to test it. ...but don't feel obligated > > > >>> + s5m8767_dvs: s5m8767-dvs { > >>> + samsung,pins = "gpd1-0", "gpd1-1", "gpd1-2"; > >>> + samsung,pin-function = <0>; > >>> + samsung,pin-pud = <1>; > >>> + samsung,pin-drv = <0>; > >>> + }; > >>> + > >>> + s5m8767_ds: s5m8767-ds { > >>> + samsung,pins = "gpx2-3", "gpx2-4", "gpx2-5"; > >>> + samsung,pin-function = <0>; > >>> + samsung,pin-pud = <1>; > >>> + samsung,pin-drv = <0>; > >>> + }; > >>> + > >>> + tps65090_irq: tps65090-irq { > >>> + samsung,pins = "gpx2-6"; > >>> + samsung,pin-function = <0>; > >>> + samsung,pin-pud = <0>; > >>> + samsung,pin-drv = <0>; > >>> + }; > >>> + > >>> + s5m8767_irq: s5m8767-irq { > >>> + samsung,pins = "gpx3-2"; > >>> + samsung,pin-function = <0>; > >>> + samsung,pin-pud = <0>; > >>> + samsung,pin-drv = <0>; > >>> + }; > >>> + > >>> + hdmi_hpd_irq: hdmi-hpd-irq { > >>> + samsung,pins = "gpx3-7"; > >>> + samsung,pin-function = <0>; > >>> + samsung,pin-pud = <1>; > >>> + samsung,pin-drv = <0>; > >>> + }; > >>> + }; > >>> + > >>> + pinctrl at 13400000 { > >>> + hsic_reset: hsic-reset { > >>> + samsung,pins = "gpe1-0"; > >>> + samsung,pin-function = <1>; > >>> + samsung,pin-pud = <0>; > >>> + samsung,pin-drv = <0>; > >>> + }; > >> > >> I'm pretty sure that the HSIC reset needed some funky code to make it > >> work and I'm not sure what the status of that is upstream > > > > Yeah, you mentioned something along those lines. However it's the > > equivalent of the usb3-vbus-en in -snow.dts. Rename or drop? It's clearly not equivalent, usb3-vbus-en just turns on/off the load switch for VBUS while the HSIC chip (USB3503) is an external PHY (and hub) for the USB2 port, the reset of the PHY side of the HSIC needs to be done within the proper timing window compared to the SoC HSIC controller to get a working link. As the current kernel has a binding for the SMSC USB3503 and a PHY driver (which is in driver/usb/misc probably because it is an external PHY), the hsic-reset should be connected there (as "reset-gpios"). On top of that the HSIC link is a bit finicky and it needs a few quirks if we want it to survive all kind of events : eg s5p_hub_control() in https://chromium.googlesource.com/chromiumos/third_party/kernel/+/chromeos-3.8/drivers/usb/host/ehci-s5p.c > > On snow locally I see USB2 vbus is gpx1-1 and USB3 vbus is gpx2-7. I > don't see that in spring. On Spring, the USB3 root hub is just connected to the internal camera (which is powered by one of the TPS65090 LDOs) On the external USB2 ports, the port enable going to the VBUS load switch is controlled directly the USB3503 (which has an internal mechanism, configured by default as an automatic control of overcurrent protection, it can be bypass by using the USB3503 I2C registers). > This will take more time than I have right now to track down. I added > Julius to the thread in case he has time to answer and can suggest > what to do for upstream purposes. I may be able to look more > tomorrow. > > You can always send up the next version and include this and we'll > look at it again. > > > >>> + }; > >>> + > >>> + vbat: vbat-fixed-regulator { > >>> + compatible = "regulator-fixed"; > >>> + regulator-name = "vbat-supply"; > >>> + regulator-boot-on; > >>> + }; > >>> + > >>> + usb at 12000000 { > >>> + status = "okay"; > >>> + }; > >>> + > >>> + usb3_vbus_reg: regulator-usb3 { > >>> + compatible = "regulator-fixed"; > >>> + regulator-name = "P5.0V_USB3CON"; > >>> + regulator-min-microvolt = <5000000>; > >>> + regulator-max-microvolt = <5000000>; > >>> + gpio = <&gpe1 0 1>; > >>> + pinctrl-names = "default"; > >>> + pinctrl-0 = <&hsic_reset>; > >>> + enable-active-high; > >>> + }; > >>> + > >>> + phy at 12100000 { > >>> + vbus-supply = <&usb3_vbus_reg>; > >>> + }; > >>> + > >>> + usb at 12110000 { > >>> + samsung,vbus-gpio = <&gpx1 1 0>; > >>> + status = "okay"; > >>> + }; > >>> + > >>> + usb at 12120000 { > >>> + status = "okay"; > >>> + }; > >>> + > >>> + mmc at 12220000 { > >>> + /* MMC2 pins are used as GPIO for eDP bridge control. */ > >>> + status = "disabled"; > >>> + }; > >>> + > >>> + mmc at 12230000 { > >>> + status = "disabled"; > >>> + }; > >>> + > >>> + i2c at 12C60000 { > >>> + max77686 at 09 { > >> > >> There is no max77686 on spring. It uses s5m8767 in the place of max77686. > >> > >> ...you've got "status = disabled", just remove it. > > > > That's because it's inherited from exynos5250-cros-common.dtsi. > > Ah, right. So if we're keeping cros-common the proper thing to do is > to move it out of cros-common in a patch before this one. ...but I > think people might be happier if you simply don't include cros-common. > > > > The rtc that the system successfully uses is "s5m-rtc", which I guess is > > on the s5m8767 then? (Confusing that 3.8 Spring had this rtc node > > despite Snow's max77686 not having it.) > > I think it's not really supposed to. It was a bit of a hack to handle > the fact that the RTC has two different i2c addresses on both the > 77686 and this PMIC. The max77686 driver upstream handles it all in > code and doesn't ask the device tree to list both addresses. > > I think that _upstream_ snow doesn't have the node but _downstream_ > spring might have the node (though having a child of a disabled node > isn't particularly useful). > > > >>> + #address-cells = <1>; > >>> + #size-cells = <0>; > >>> + status = "disabled"; > >>> + > >>> + rtc { > >>> + reg = <0x6>; > >>> + }; > >>> + }; > >>> + > >>> + s5m8767_pmic at 66 { > >>> + compatible = "samsung,s5m8767-pmic"; > >>> + reg = <0x66>; > >>> + interrupt-parent = <&gpx3>; > >>> + interrupts = <2 0>; > >>> + pinctrl-names = "default"; > >>> + pinctrl-0 = <&s5m8767_irq &s5m8767_dvs &s5m8767_ds>; > >>> + wakeup-source; > >>> + > >>> + s5m8767,pmic-buck-dvs-gpios = <&gpd1 0 1>, /* DVS1 */ > >>> + <&gpd1 1 1>, /* DVS2 */ > >>> + <&gpd1 2 1>; /* DVS3 */ > >>> + > >>> + s5m8767,pmic-buck-ds-gpios = <&gpx2 3 1>, /* SET1 */ > >>> + <&gpx2 4 1>, /* SET2 */ > >>> + <&gpx2 5 1>; /* SET3 */ > >> > >> The final "1" in each of the GPIO specifiers above should be GPIO_ACTIVE_LOW. > >> > >> > >>> + > >>> + /* > >>> + * The following arrays of DVS voltages are not used, since we are > >>> + * not using GPIOs to control PMIC bucks, but they must be defined > >>> + * to please the driver. > >>> + */ > >>> + s5m8767,pmic-buck2-dvs-voltage = <1350000>, <1300000>, > >>> + <1250000>, <1200000>, > >>> + <1150000>, <1100000>, > >>> + <1000000>, <950000>; > >>> + > >>> + s5m8767,pmic-buck3-dvs-voltage = <1100000>, <1100000>, > >>> + <1100000>, <1100000>, > >>> + <1000000>, <1000000>, > >>> + <1000000>, <1000000>; > >>> + > >>> + s5m8767,pmic-buck4-dvs-voltage = <1200000>, <1200000>, > >>> + <1200000>, <1200000>, > >>> + <1200000>, <1200000>, > >>> + <1200000>, <1200000>; > >>> + > >>> + clocks { > >>> + compatible = "samsung,s5m8767-clk"; > >>> + #clock-cells = <1>; > >>> + clock-output-names = "en32khz_ap", > >>> + "en32khz_cp", > >>> + "en32khz_bt"; > >>> + }; > >>> + > >>> + regulators { > >>> + s5m_ldo4_reg: LDO4 { > >>> + regulator-name = "P1.0V_LDO_OUT4"; > >>> + regulator-min-microvolt = <1000000>; > >>> + regulator-max-microvolt = <1000000>; > >>> + regulator-always-on; > >>> + op_mode = <0>; > >> > >> I think that "op_mode" here is questionable. Adding Javier to the > >> thread who was looking at this for max77802 and possibly max77686. > > > > Confirming that this op_mode is present in the original 3.8 device tree. > > Yes and it needs to be handled eventually. It makes suspend/resume > work properly. ...but I think it needs to be thought out better. > > ...but given that other users of this PMIC have it I guess it makes > sense to leave it in. Javier was going to try to think it through > better for max77686 and max77802. > > > > (I used dtc to compile my /proc/device-tree tarball back to .dts, so it > > has hexadecimal <0x0> but that shouldn't matter to dtc AFAIU.) > > > >>> + }; > >>> + > >>> + s5m_ldo5_reg: LDO5 { > >>> + regulator-name = "P1.0V_LDO_OUT5"; > >>> + regulator-min-microvolt = <1000000>; > >>> + regulator-max-microvolt = <1000000>; > >>> + regulator-always-on; > >>> + op_mode = <0>; > >>> + }; > >>> + > >>> + s5m_ldo6_reg: LDO6 { > >>> + regulator-name = "vdd_mydp"; > >>> + regulator-min-microvolt = <1000000>; > >>> + regulator-max-microvolt = <1000000>; > >>> + regulator-always-on; > >>> + op_mode = <3>; > >>> + }; > >>> + > >>> + s5m_ldo7_reg: LDO7 { > >>> + regulator-name = "P1.1V_LDO_OUT7"; > >>> + regulator-min-microvolt = <1100000>; > >>> + regulator-max-microvolt = <1100000>; > >>> + regulator-always-on; > >>> + op_mode = <3>; > >>> + }; > >>> + > >>> + s5m_ldo8_reg: LDO8 { > >>> + regulator-name = "P1.0V_LDO_OUT8"; > >>> + regulator-min-microvolt = <1000000>; > >>> + regulator-max-microvolt = <1000000>; > >>> + regulator-always-on; > >>> + op_mode = <3>; > >>> + }; > >>> + > >>> + s5m_ldo10_reg: LDO10 { > >>> + regulator-name = "P1.8V_LDO_OUT10"; > >>> + regulator-min-microvolt = <1800000>; > >>> + regulator-max-microvolt = <1800000>; > >>> + regulator-always-on; > >>> + op_mode = <3>; > >>> + }; > >>> + > >>> + s5m_ldo11_reg: LDO11 { > >>> + regulator-name = "P1.8V_LDO_OUT11"; > >>> + regulator-min-microvolt = <1800000>; > >>> + regulator-max-microvolt = <1800000>; > >>> + regulator-always-on; > >>> + op_mode = <0>; > >>> + }; > >>> + > >>> + s5m_ldo12_reg: LDO12 { > >>> + regulator-name = "P3.0V_LDO_OUT12"; > >>> + regulator-min-microvolt = <3000000>; > >>> + regulator-max-microvolt = <3000000>; > >>> + regulator-always-on; > >>> + op_mode = <3>; > >>> + }; > >>> + > >>> + s5m_ldo13_reg: LDO13 { > >>> + regulator-name = "P1.8V_LDO_OUT13"; > >>> + regulator-min-microvolt = <1800000>; > >>> + regulator-max-microvolt = <1800000>; > >>> + regulator-always-on; > >>> + op_mode = <0>; > >>> + }; > >>> + > >>> + s5m_ldo14_reg: LDO14 { > >>> + regulator-name = "P1.8V_LDO_OUT14"; > >>> + regulator-min-microvolt = <1800000>; > >>> + regulator-max-microvolt = <1800000>; > >>> + regulator-always-on; > >>> + op_mode = <3>; > >>> + }; > >>> + > >>> + s5m_ldo15_reg: LDO15 { > >>> + regulator-name = "P1.0V_LDO_OUT15"; > >>> + regulator-min-microvolt = <1000000>; > >>> + regulator-max-microvolt = <1000000>; > >>> + regulator-always-on; > >>> + op_mode = <3>; > >>> + }; > >>> + > >>> + s5m_ldo16_reg: LDO16 { > >>> + regulator-name = "P1.8V_LDO_OUT16"; > >>> + regulator-min-microvolt = <1800000>; > >>> + regulator-max-microvolt = <1800000>; > >>> + regulator-always-on; > >>> + op_mode = <3>; > >>> + }; > >>> + > >>> + s5m_ldo17_reg: LDO17 { > >>> + regulator-name = "P2.8V_LDO_OUT17"; > >>> + regulator-min-microvolt = <2800000>; > >>> + regulator-max-microvolt = <2800000>; > >>> + regulator-always-on; > >>> + op_mode = <0>; > >>> + }; > >>> + > >>> + s5m_ldo25_reg: LDO25 { > >>> + regulator-name = "vdd_bridge"; > >>> + regulator-min-microvolt = <1200000>; > >>> + regulator-max-microvolt = <1200000>; > >>> + regulator-always-on; > >>> + op_mode = <1>; > >>> + }; > >>> + > >>> + BUCK1 { > >>> + regulator-name = "vdd_mif"; > >>> + regulator-min-microvolt = <950000>; > >>> + regulator-max-microvolt = <1300000>; > >>> + regulator-always-on; > >>> + regulator-boot-on; > >>> + op_mode = <3>; > >>> + }; > >>> + > >>> + BUCK2 { > >>> + regulator-name = "vdd_arm"; > >>> + regulator-min-microvolt = <850000>; > >>> + regulator-max-microvolt = <1350000>; > >>> + regulator-always-on; > >>> + regulator-boot-on; > >>> + op_mode = <3>; > >>> + }; > >>> + > >>> + BUCK3 { > >>> + regulator-name = "vdd_int"; > >>> + regulator-min-microvolt = <900000>; > >>> + regulator-max-microvolt = <1200000>; > >>> + regulator-always-on; > >>> + regulator-boot-on; > >>> + op_mode = <3>; > >>> + }; > >>> + > >>> + BUCK4 { > >>> + regulator-name = "vdd_g3d"; > >>> + regulator-min-microvolt = <850000>; > >>> + regulator-max-microvolt = <1300000>; > >>> + regulator-boot-on; > >>> + op_mode = <3>; > >>> + }; > >>> + > >>> + BUCK5 { > >>> + regulator-name = "P1.8V_BUCK_OUT5"; > >>> + regulator-min-microvolt = <1800000>; > >>> + regulator-max-microvolt = <1800000>; > >>> + regulator-always-on; > >>> + regulator-boot-on; > >>> + op_mode = <1>; > >>> + }; > >>> + > >>> + BUCK6 { > >>> + regulator-name = "P1.2V_BUCK_OUT6"; > >>> + regulator-min-microvolt = <1200000>; > >>> + regulator-max-microvolt = <1200000>; > >>> + regulator-always-on; > >>> + regulator-boot> > >> > > -on; > >>> + op_mode = <0>; > >>> + }; > >>> + > >>> + BUCK9 { > >>> + regulator-name = "vdd_ummc"; > >>> + regulator-min-microvolt = <950000>; > >>> + regulator-max-microvolt = <3000000>; > >>> + regulator-always-on; > >>> + regulator-boot-on; > >>> + op_mode = <3>; > >>> + }; > >>> + }; > >>> + }; > >>> + }; > >>> + > >>> + i2c at 12C70000 { > >>> + trackpad { > >>> + status = "disabled"; > >> > >> Having this bogus entry here doesn't add anything. Remove it until > >> the trackpad should be added. See http://crbug.com/371114 for a > >> slightly stale bug about trackpad. > > > > You misunderstand: This resolves an error about the cypress,cyapa > > inherited from -cros-common.dtsi. Spring uses a different device and two > > different I2C addresses. > > Ah, right. I forgot about cros5250-common. > > > > Nodes named trackpad-bootloader and trackpad-alt are prepared here: > > https://github.com/afaerber/linux/commits/spring-next > > It might work, but you run into pinctrl problems. You need to put the > pinctrl node _somewhere_ and if you put it with the trackpad entries > themselves then you get conflicts. ...and it doesn't belong in the > i2c bus (though that's what we have locally in our tree) > > See <http://permalink.gmane.org/gmane.linux.kernel.samsung-soc/30953> > for some background. > > > >>> + }; > >>> + }; > >>> + > >>> + i2c at 12CA0000 { > >>> + embedded-controller { > >> > >> Add "cros_ec" alias like snow. > >> > >> > >>> + compatible = "google,cros-ec-i2c"; > >>> + reg = <0x1e>; > >>> + interrupts = <6 0>; > >>> + interrupt-parent = <&gpx1>; > >>> + wakeup-source; > >>> + > >>> + keyboard-controller { > >> > >> Don't include keyboard-controller here. Add: > >> > >> #include "cros-ec-keyboard.dtsi" > >> > >> ...at the bottom. Note that I think that the spring EC has a special > >> "charger" key that it uses to indicate when a charger was plugged in > >> and unplugged. I'm not sure how that will end up getting supported > >> upstream but you could just leave it out for now. > > > > Is there such a pending patch for snow? That's what I modeled after. > > Yeah, and it appears to be in linux-next. (1a395e3 ARM: dts: Use the > cros-ec-keyboard fragment in exynos5250-snow). It actually ended up > going through the tegra tree since it was in a series with a similar > tegra change. I asked Kukjin to pick it up via merge but he didn't > appear to. > > > > Where is cros-ec-keyboard.dtsi? Don't see it in > > http://git.kernel.org/cgit/linux/kernel/git/kgene/linux-samsung.git/tree/arch/arm/boot/dts?h=for-next > > or > > http://git.kernel.org/cgit/linux/kernel/git/kgene/linux-samsung.git/tree/include/dt-bindings?h=for-next > > > > Are you proposing I factor it out? > > > >>> + compatible = "google,cros-ec-keyb"; > >>> + keypad,num-rows = <8>; > >>> + keypad,num-columns = <13>; > >> > >> Don't you need pinctrl here? > > > > The keyboard is usable; what would pinctrl be needed for? There's none > > in the 3.8 device tree. > > Generally it's good to have the pinctrl listed to configure the IRQ > properly (get the pulls right). It might work without it but it's a > little less ideal I think. > > I see this, right? > > pinctrl-names = "default"; > pinctrl-0 = <&ec_irq>; > > ...in the downstream "arch/arm/boot/dts/exynos5250-spring.dts" > > > >>> + google,needs-ghost-filter; > >>> + linux,keymap = < > >>> + 0x0001007d /* L_META */ > >>> + 0x0002003b /* F1 */ > >>> + 0x00030030 /* B */ > >>> + 0x00040044 /* F10 */ > >>> + 0x00060031 /* N */ > >>> + 0x0008000d /* = */ > >>> + 0x000a0064 /* R_ALT */ > >>> + > >>> + 0x01010001 /* ESC */ > >>> + 0x0102003e /* F4 */ > >>> + 0x01030022 /* G */ > >>> + 0x01040041 /* F7 */ > >>> + 0x01060023 /* H */ > >>> + 0x01080028 /* ' */ > >>> + 0x01090043 /* F9 */ > >>> + 0x010b000e /* BKSPACE */ > >>> + > >>> + 0x0200001d /* L_CTRL */ > >>> + 0x0201000f /* TAB */ > >>> + 0x0202003d /* F3 */ > >>> + 0x02030014 /* T */ > >>> + 0x02040040 /* F6 */ > >>> + 0x0205001b /* ] */ > >>> + 0x02060015 /* Y */ > >>> + 0x02070056 /* 102ND */ > >>> + 0x0208001a /* [ */ > >>> + 0x02090042 /* F8 */ > >>> + > >>> + 0x03010029 /* GRAVE */ > >>> + 0x0302003c /* F2 */ > >>> + 0x03030006 /* 5 */ > >>> + 0x0304003f /* F5 */ > >>> + 0x03060007 /* 6 */ > >>> + 0x0308000c /* - */ > >>> + 0x030b002b /* \ */ > >>> + > >>> + 0x04000061 /* R_CTRL */ > >>> + 0x0401001e /* A */ > >>> + 0x04020020 /* D */ > >>> + 0x04030021 /* F */ > >>> + 0x0404001f /* S */ > >>> + 0x04050025 /* K */ > >>> + 0x04060024 /* J */ > >>> + 0x04080027 /* ; */ > >>> + 0x04090026 /* L */ > >>> + 0x040a002b /* \ */ > >>> + 0x040b001c /* ENTER */ > >>> + > >>> + 0x0501002c /* Z */ > >>> + 0x0502002e /* C */ > >>> + 0x0503002f /* V */ > >>> + 0x0504002d /* X */ > >>> + 0x05050033 /* , */ > >>> + 0x05060032 /* M */ > >>> + 0x0507002a /* L_SHIFT */ > >>> + 0x05080035 /* / */ > >>> + 0x05090034 /* . */ > >>> + 0x050B0039 /* SPACE */ > >>> + > >>> + 0x06010002 /* 1 */ > >>> + 0x06020004 /* 3 */ > >>> + 0x06030005 /* 4 */ > >>> + 0x06040003 /* 2 */ > >>> + 0x06050009 /* 8 */ > >>> + 0x06060008 /* 7 */ > >>> + 0x0608000b /* 0 */ > >>> + 0x0609000a /* 9 */ > >>> + 0x060a0038 /* L_ALT */ > >>> + 0x060b006c /* DOWN */ > >>> + 0x060c006a /* RIGHT */ > >>> + > >>> + 0x07010010 /* Q */ > >>> + 0x07020012 /* E */ > >>> + 0x07030013 /* R */ > >>> + 0x07040011 /* W */ > >>> + 0x07050017 /* I */ > >>> + 0x07060016 /* U */ > >>> + 0x07070036 /* R_SHIFT */ > >>> + 0x07080019 /* P */ > >>> + 0x07090018 /* O */ > >>> + 0x070b0067 /* UP */ > >>> + 0x070c0069 /* LEFT */ > >>> + >; > >>> + }; > >>> + }; > >>> + > >>> + power-regulator { > >>> + compatible = "ti,tps65090"; > >> > >> I doubt tps65090 will "just work". Does it? > > > > Good question. How to tell? :) Not familiar with clocks and regulators. > > I don't see the nodes referenced anywhere, so I could just try to drop > > (as I would, as per my cover letter, propose for anything non-essential > > that turns controversial). > > What does "dmesg | grep tps65090" say? > > What does this show: > grep "" /sys/class/regulator/*/name > > > > If we drop tps65090, can we safely drop vbat-fixed-regulator as well? > > Yes > > > >> On spring the tps65090 is not directly on the same i2c bus as the EC. > >> It's actually hidden behind the EC. > >> > >> Locally in the ChromeOS tree there appears to be a forked copy of the > >> 65090 regulator driver that's in use just for spring. See this from > >> the ChromeOS 3.8 tree: > >> > >> ./drivers/regulator/tps65090-regulator.c > >> ./drivers/regulator/cros_ec-tps65090.c > >> > >> The Spring version of the driver sends EC commands directly to access > >> the tps65090. > >> > >> It is possible (untested) that you could also talk to tps65090 over an > >> i2c tunnel. On exynos5420-peach-pit we have a full fledged i2c > >> tunnel, but you may be able to extend the tunnel to export an i2c > >> tunnel for spring using something like > >> <https://chromium-review.googlesource.com/66116> > > > > The SBS battery thingy (not in this patch) should also be behind some > > tunnel. There's none defined in -cros-common.dtsi or in my patch, and > > still it shows up in dmesg to my surprise, complaining "Couldn't read > > remote-bus property". > > Might be due to the cros5250-common. ...but yes, the battery should > be behind the tunnel too and the patches needed for Spring haven't > been posted by anyone yet. I picked up a whole bunch of cros_ec > cleanup patches and thought that the tunnel patches for spring could > possible go up after those land. > > > >>> + reg = <0x48>; > >>> + > >>> + /* > >>> + * Config irq to disable internal pulls > >>> + * even though we run in polling mode. > >>> + */ > >>> + pinctrl-names = "default"; > >>> + pinctrl-0 = <&tps65090_irq>; > >>> + > >>> + vsys1-supply = <&vbat>; > >>> + vsys2-supply = <&vbat>; > >>> + vsys3-supply = <&vbat>; > >>> + infet1-supply = <&vbat>; > >>> + infet2-supply = <&vbat>; > >>> + infet3-supply = <&vbat>; > >>> + infet4-supply = <&vbat>; > >>> + infet5-supply = <&vbat>; > >>> + infet6-supply = <&vbat>; > >>> + infet7-supply = <&vbat>; > >>> + vsys-l1-supply = <&vbat>; > >>> + vsys-l2-supply = <&vbat>; > >>> + > >>> + regulators { > >>> + fet1 { > >>> + regulator-name = "vcd_led"; > >>> + regulator-min-microvolt = <12000000>; > >>> + regulator-max-microvolt = <12000000>; > >>> + }; > >>> + fet3 { > >>> + regulator-name = "wwan_r"; > >>> + regulator-min-microvolt = <3300000>; > >>> + regulator-max-microvolt = <3300000>; > >>> + regulator-always-on; > >>> + }; > >>> + fet5 { > >>> + regulator-name = "cam"; > >>> + regulator-min-microvolt = <3300000>; > >>> + regulator-max-microvolt = <3300000>; > >>> + regulator-always-on; > >>> + }; > >>> + fet6 { > >>> + regulator-name = "lcd_vdd"; > >>> + regulator-min-microvolt = <3300000>; > >>> + regulator-max-microvolt = <3300000>; > >>> + }; > >>> + fet7 { > >>> + regulator-name = "ts"; > >>> + regulator-min-microvolt = <5000000>; > >>> + regulator-max-microvolt = <5000000>; > >>> + }; > >>> + }; > >>> + > >>> + charger { > >>> + compatible = "ti,tps65090-charger"; > >>> + }; > >>> + }; > >>> + }; > >>> + > >>> + hdmi { > >>> + hdmi-en-supply = <&s5m_ldo8_reg>; > >>> + vdd-supply = <&s5m_ldo8_reg>; > >>> + vdd_osc-supply = <&s5m_ldo10_reg>; > >>> + vdd_pll-supply = <&s5m_ldo8_reg>; > >>> + }; > >>> + > >>> + fimd at 14400000 { > >>> + status = "okay"; > >>> + samsung,invert-vclk; > >>> + }; > >>> + > >>> + dp-controller at 145B0000 { > >>> + status = "okay"; > >>> + pinctrl-names = "default"; > >>> + pinctrl-0 = <&dp_hpd>; > >> > >> This is probably not right. It looks as if spring uses gpc3-0 for > >> display port HPD (as a GPIO). The upstream has this in the > >> exynos5250-pinctrl.dtsi as a different pin. > >> > >> I think you'll need to define your own pinctrl here. > >> > >> > >>> + samsung,color-space = <0>; > >>> + samsung,dynamic-range = <0>; > >>> + samsung,ycbcr-coeff = <0>; > >>> + samsung,color-depth = <1>; > >>> + samsung,link-rate = <0x0a>; > >>> + samsung,lane-count = <1>; > >>> + samsung,hpd-gpio = <&gpc3 0 0>; > >>> + > >>> + display-timings { > >>> + native-mode = <&timing1>; > >>> + > >>> + timing1: timing at 1 { > >>> + clock-frequency = <70589280>; > >>> + hactive = <1366>; > >>> + vactive = <768>; > >>> + hfront-porch = <40>; > >>> + hback-porch = <40>; > >>> + hsync-len = <32>; > >>> + vback-porch = <10>; > >>> + vfront-porch = <12>; > >>> + vsync-len = <6>; > >>> + }; > >>> + }; > >>> + }; > >>> + > >>> + fixed-rate-clocks { > >>> + xxti { > >>> + compatible = "samsung,clock-xxti"; > >>> + clock-frequency = <24000000>; > >>> + }; > >>> + }; > >>> +}; > > > > Will check on the other suggestions. > > -Doug ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2014-06-24 15:20 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1403486483-4063-1-git-send-email-afaerber@suse.de>
2014-06-23 1:21 ` [RFC 4/4] ARM: dts: exynos5250: Add Spring device tree Andreas Färber
2014-06-23 19:47 ` Doug Anderson
2014-06-23 22:46 ` Andreas Färber
2014-06-24 4:05 ` Doug Anderson
2014-06-24 10:06 ` Javier Martinez Canillas
2014-06-24 15:20 ` Doug Anderson
2014-06-24 15:06 ` Vincent Palatin
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).