timers & suspend

[daniel.lezcano@linaro.org (Daniel Lezcano)]

On 07/03/2014 07:40 PM, S?ren Brinkmann wrote:
> On Thu, 2014-07-03 at 07:26PM +0200, Daniel Lezcano wrote:
>> On 07/03/2014 06:09 PM, S?ren Brinkmann wrote:
>>> On Thu, 2014-07-03 at 02:21PM +0200, Daniel Lezcano wrote:
>>>> On 06/30/2014 08:39 PM, S?ren Brinkmann wrote:
>>>>> Hi,
>>>>>
>>>>> I'm currently working on suspend for Zynq and try to track down some
>>>>> spurious wakes. It looks like the spurious wakes are caused by timers,
>>>>> hence I was wondering whether there are any special requirements for
>>>>> timer drivers when it comes to suspend support or if I just missed
>>>>> something.
>>>>>
>>>>> Zynq sets the 'IRQCHIP_MASK_ON_SUSPEND' flag, which should mask all
>>>>> interrupts but the wake source. Reading through kernel/irq/pm.c
>>>>> indicates, that timer interrupts get some special treatment though.
>>>>> Therefore I implemented some suspend/resume callbacks for the
>>>>> cadence_ttc which disable and clear the timer's interrupts when going
>>>>> into suspend. That seems to mitigate the issue quite a bit, but I still
>>>>> saw spurious wakes - just a lot less often.
>>>>> Digging a little deeper revealed, the spurious wakes are caused by the
>>>>> ARM's smp_twd timer now. Given that that driver is probably used by a few
>>>>> more ARM platforms, I get the feeling that I'm missing something.
>>>>
>>>> Do you receive any interrupt from the cadence_ttc ? (/proc/interrupts)
>>>>
>>>> That's funny because I realize that you cadence ttc timer is never
>>>> used as there are the architected timers. The cadence ttc would be
>>>> only useful if there were an idle state powering down the smp_twd
>>>> timers but it is not the case on this board, IIUC.
>>> Yes they are used. They TTC is the only broadcast capable timer for
>>> Zynq. In my experience, I can not even boot without it (may have
>>> dependencies on CPUidle or something).
>>
>> Actually the cpuidle driver is wrong. It assumes the state #1 will
>> power off the different cores with their architected timers and then
>> switch to the broadcast timer. But this one is not needed as we
>> don't power down the core with the twd timers, so no need to switch
>> to a backup timer device.
>>
>> The implementation of the DDR self refresh idle state (incoming
>> patchset) removes the cpu_pm notifiers + the flag TIMER_STOP. The
>> result is 0 interrupts for ttc cadence timer. I removed in the dts
>> the cadence ttc and my board booted without problem (it is a zynq
>> 702).
>>
>> Except I missed something, the cadence ttc is actually not used at all.
> I tested on the current master branch. I see TTC interrupts on CPU0 and
> timer_list shows the TTC to be the broadcast device. Removing the TTC
> nodes from my DT results in boot hanging - shortly after cpuidle is
> started.
>
> Removing cpuidle from my kernel makes the system boot. And it has no
> broadcast device anymore.

You can safely remove the CPUIDLE_FLAG_TIMER_STOP in the cpuidle drivers 
and I am pretty sure it will boot without problem.

-- 
  <http://www.linaro.org/> Linaro.org ? Open source software for ARM SoCs

Follow Linaro:  <http://www.facebook.com/pages/Linaro> Facebook |
<http://twitter.com/#!/linaroorg> Twitter |
<http://www.linaro.org/linaro-blog/> Blog