From mboxrd@z Thu Jan  1 00:00:00 1970
From: varkabhadram@gmail.com (Varka Bhadram)
Date: Wed, 16 Jul 2014 14:56:43 +0530
Subject: [PATCH v3 1/8] of: Add NVIDIA Tegra SATA controller binding
In-Reply-To: <1405500863-19696-2-git-send-email-mperttunen@nvidia.com>
References: <1405500863-19696-1-git-send-email-mperttunen@nvidia.com>
 <1405500863-19696-2-git-send-email-mperttunen@nvidia.com>
Message-ID: <53C64553.9010704@gmail.com>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

On 07/16/2014 02:24 PM, Mikko Perttunen wrote:
> This patch adds device tree binding documentation for the SATA
> controller found on NVIDIA Tegra SoCs.
>
> Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
> ---
>   .../devicetree/bindings/ata/tegra-sata.txt         | 30 ++++++++++++++++++++++
>   1 file changed, 30 insertions(+)
>   create mode 100644 Documentation/devicetree/bindings/ata/tegra-sata.txt
>
> diff --git a/Documentation/devicetree/bindings/ata/tegra-sata.txt b/Documentation/devicetree/bindings/ata/tegra-sata.txt
> new file mode 100644
> index 0000000..946f207
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/ata/tegra-sata.txt
> @@ -0,0 +1,30 @@
> +Tegra124 SoC SATA AHCI controller
> +
> +Required properties :
> +- compatible : "nvidia,tegra124-ahci".
> +- reg : Should contain 2 entries:
> +  - AHCI register set (SATA BAR5)
> +  - SATA register set
> +- interrupts : Defines the interrupt used by SATA
> +- clocks : Must contain an entry for each entry in clock-names.
> +  See ../clocks/clock-bindings.txt for details.
> +- clock-names : Must include the following entries:
> +  - sata
> +  - sata-oob
> +  - cml1
> +  - pll_e

It would be more readable if it like this...

Required properties :
- compatible	: "nvidia,tegra124-ahci".
- reg		: Should contain 2 entries:
		  - AHCI register set (SATA BAR5)
		  - SATA register set
- interrupts	: Defines the interrupt used by SATA
- clocks	: Must contain an entry for each entry in clock-names.
		  See ../clocks/clock-bindings.txt for details.
....

> +- resets : Must contain an entry for each entry in reset-names.
> +  See ../reset/reset.txt for details.
> +- reset-names : Must include the following entries:
> +  - sata
> +  - sata-oob
> +  - sata-cold
> +- phys : Must contain an entry for each entry in phy-names.
> +  See ../phy/phy-bindings.txt for details.
> +- phy-names : Must include the following entries:
> +  - sata-phy : XUSB PADCTL SATA PHY
> +- hvdd-supply : Defines the SATA HVDD regulator
> +- vddio-supply : Defines the SATA VDDIO regulator
> +- avdd-supply : Defines the SATA AVDD regulator
> +- target-5v-supply : Defines the SATA 5V power regulator
> +- target-12v-supply : Defines the SATA 12V power regulator

Same....


-- 
Regards,
Varka Bhadram.