[PATCH v2 0/6] Add initial support for Broadcom Cygnus SoC

From: f.fainelli@gmail.com (Florian Fainelli)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v2 0/6] Add initial support for Broadcom Cygnus SoC
Date: Thu, 25 Sep 2014 17:14:10 -0700	[thread overview]
Message-ID: <5424AFD2.2070406@gmail.com> (raw)
In-Reply-To: <54248791.9060805@gmail.com>

Scott, Jonathan,

On 09/25/2014 02:22 PM, Florian Fainelli wrote:
> Hi Scott,
> 
> On 09/25/2014 02:04 PM, Scott Branden wrote:
>> Hi Matt/Christian (and others),
>>
>> We would like to move forward in getting our base Cygnus support into
>> the mainline kernel.  From there we will be able to contribute
>> additional drivers.
>>
>> Is somebody willing to accept this pull request to get this patchset
>> accepted by the open source community?
> 
> I am fine with taking the ARM patches and putting them at
> http://github/brcm/linux.git, with C code in cygnus/board and the Device
> Tree files in cygnus/dt for instance?
> 
> The clock driver patch will have to go through Mike Turquette's tree
> unless he wants to delegate that one.

Could you resend patch 3 without the clock binding, patch 4 without the
clocks node, and patch 6 without the drivers/clk changes? Once you do
that, I can assemble these patches quickly and send a pull request which
does only contain ARM SoC and DTS changes, and you can get the clock
driver to be reviewed separately by its maintainer?

Thanks!

> 
>>
>> Regards,
>>  Scott
>>
>>
>> On 14-09-23 02:17 PM, Jonathan Richardson wrote:
>>> Hi,
>>>
>>> This patchset contains initial support for Broadcom's Cygnus SoC based
>>> on our
>>> iProc architecture. Initial support is minimal and includes just the mach
>>> platform code, clock driver, and a basic device tree configuration.
>>> Peripheral
>>> drivers will be submitted soon, as will device tree configurations for
>>> other
>>> Cygnus board variants.
>>>
>>> Changes from v1:
>>>   - Address code review comments as per previous responses.
>>>   - Copyright headers updated to remove Broadcom URL.
>>>   - mach platform code still contains hard coded adresses. These
>>> address are
>>>     the same for all Cygnus variants. Could you please provide
>>> guidance on where
>>>     they should go if you would still like them changed.
>>>
>>> Thanks,
>>> Jon
>>>
>>> Jonathan Richardson (6):
>>>    ARM: cygnus: Initial support for Broadcom Cygnus SoC
>>>    clk: Clock driver support for Broadcom Cygnus SoC
>>>    dt-bindings: Document Broadcom Cygnus SoC and clock driver
>>>    ARM: dts: Enable Broadcom Cygnus SoC
>>>    ARM: cygnus defconfig : Initial defconfig for Broadcom Cygnus SoC
>>>    MAINTAINERS: Entry for Cygnus/iproc arm architecture and clock
>>>      drivers
>>>
>>>   Documentation/devicetree/bindings/arm/cygnus.txt   |   12 +
>>>   .../devicetree/bindings/clock/clk-cygnus.txt       |  121 ++
>>>   .../devicetree/bindings/clock/clk-iproc.txt        |   48 +
>>>   MAINTAINERS                                        |   21 +
>>>   arch/arm/boot/dts/Makefile                         |    1 +
>>>   arch/arm/boot/dts/bcm-cygnus.dtsi                  |  349 ++++++
>>>   arch/arm/boot/dts/bcm911360_entphn.dts             |   22 +
>>>   arch/arm/configs/bcm_cygnus_defconfig              |  223 ++++
>>>   arch/arm/mach-bcm/Kconfig                          |   31 +
>>>   arch/arm/mach-bcm/Makefile                         |    3 +
>>>   arch/arm/mach-bcm/bcm_cygnus.c                     |  166 +++
>>>   drivers/clk/Makefile                               |    1 +
>>>   drivers/clk/bcm/Makefile                           |    2 +
>>>   drivers/clk/bcm/clk-cygnus.c                       | 1186
>>> ++++++++++++++++++++
>>>   drivers/clk/bcm/clk-iproc.c                        |  451 ++++++++
>>>   15 files changed, 2637 insertions(+)
>>>   create mode 100644 Documentation/devicetree/bindings/arm/cygnus.txt
>>>   create mode 100644
>>> Documentation/devicetree/bindings/clock/clk-cygnus.txt
>>>   create mode 100644
>>> Documentation/devicetree/bindings/clock/clk-iproc.txt
>>>   create mode 100644 arch/arm/boot/dts/bcm-cygnus.dtsi
>>>   create mode 100644 arch/arm/boot/dts/bcm911360_entphn.dts
>>>   create mode 100644 arch/arm/configs/bcm_cygnus_defconfig
>>>   create mode 100644 arch/arm/mach-bcm/bcm_cygnus.c
>>>   create mode 100644 drivers/clk/bcm/clk-cygnus.c
>>>   create mode 100644 drivers/clk/bcm/clk-iproc.c
>>>
>>
>>
>> _______________________________________________
>> linux-arm-kernel mailing list
>> linux-arm-kernel at lists.infradead.org
>> http://lists.infradead.org/mailman/listinfo/linux-arm-kernel
> 