* [PATCHv3 0/3] ARM: dts: Add new board dts file for Exynos3250-based Rinato board
@ 2014-10-24 11:39 Chanwoo Choi
2014-10-24 11:39 ` [PATCHv3 1/3] ARM: dts: Add " Chanwoo Choi
` (2 more replies)
0 siblings, 3 replies; 8+ messages in thread
From: Chanwoo Choi @ 2014-10-24 11:39 UTC (permalink / raw)
To: linux-arm-kernel
This patchset adds new board dts file for Samsung Rinato board (Gear 2) which
is based on Exynos3250 SoC and adds sleep mode pin configuration using pinctrl
subsystem to reduce leakage power-consumption in sleep state.
This patchset is based on linux-samsung.git (for-next branch).
Changes from v2:
- Separate patch3 from patchset[1] and then this patchset includes patch3.
After applied patch3, the power-consumption of Rinato board is 0.6mA in suspend state.
[1] [PATCHv5 0/3] regulator: of: Add support for parsing regulator suspend state
: https://lkml.org/lkml/2014/10/10/161
- Change PDN (Power-down mode) state for GPE0-3 (BT_UART_RTS) because Rinato
board uses UART1 for bluetooth device. BT_UART_RTS pin should be disabled in
suspend state by setting high state of GPE0-3
- Turn on always the regulator state of VAP_VMIPI_1.0V because if VAP_VMIPI_1.0V
is off state or would be not controlled by DRM driver, happen imprecise external abort.
Changes from v1:
- Remove useless brace
- Remove unneeded 'regulators' keyword
- Consolidate memory information in one entry
Chanwoo Choi (3):
ARM: dts: Add board dts file for Exynos3250-based Rinato board
ARM: dts: Add sleep mode pin configuration for exynos3250-rinato
ARM: dts: Add sleep mode of regulator for exynos3250-rinato board
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/exynos3250-pinctrl.dtsi | 16 +
arch/arm/boot/dts/exynos3250-rinato.dts | 695 ++++++++++++++++++++++++++++++
3 files changed, 713 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/exynos3250-rinato.dts
--
1.8.5.5
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCHv3 1/3] ARM: dts: Add board dts file for Exynos3250-based Rinato board
2014-10-24 11:39 [PATCHv3 0/3] ARM: dts: Add new board dts file for Exynos3250-based Rinato board Chanwoo Choi
@ 2014-10-24 11:39 ` Chanwoo Choi
2014-10-24 11:57 ` Krzysztof Kozłowski
2014-10-24 11:39 ` [PATCHv3 2/3] ARM: dts: Add sleep mode pin configuration for exynos3250-rinato Chanwoo Choi
2014-10-24 11:39 ` [PATCHv3 3/3] ARM: dts: Add sleep mode of regulator for exynos3250-rinato board Chanwoo Choi
2 siblings, 1 reply; 8+ messages in thread
From: Chanwoo Choi @ 2014-10-24 11:39 UTC (permalink / raw)
To: linux-arm-kernel
This patch add support for device tree sources for Samsung Rinato baord
(Gear 2) based on Exynos3250 SoC.
This dts file support following features:
- eMMC
- Main PMIC (Samsung S2MPS14)
- Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
- RTC of Exynos3250
- ADC of Exynos3250 with NTC thermistor
- I2S of Exynos3250
- TMU of Exynos3250
- MFC of Exynos3250
- Secure firmware for Exynos3250 secondary cpu boot
- Serial ports of Exynos3250
- gpio-key for power key
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Inki Dae <inki.dae@samsung.com>
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/exynos3250-rinato.dts | 433 ++++++++++++++++++++++++++++++++
2 files changed, 435 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/exynos3250-rinato.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 4a75e29..91cd4d0 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -67,7 +67,8 @@ dtb-$(CONFIG_ARCH_BRCMSTB) += \
dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \
da850-evm.dtb
dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb
-dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
+dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-rinato.dtb \
+ exynos4210-origen.dtb \
exynos4210-smdkv310.dtb \
exynos4210-trats.dtb \
exynos4210-universal_c210.dtb \
diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
new file mode 100644
index 0000000..be0ba8d
--- /dev/null
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -0,0 +1,433 @@
+/*
+ * Samsung's Exynos3250 based Rinato board device tree source
+ *
+ * Copyright (c) 2014 Samsung Electronics Co., Ltd.
+ * http://www.samsung.com
+ *
+ * Device tree source file for Samsung's Rinato board which is based on
+ * Samsung Exynos3250 SoC.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ */
+
+/dts-v1/;
+#include "exynos3250.dtsi"
+#include <dt-bindings/input/input.h>
+
+/ {
+ model = "Samsung Rinato board";
+ compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3";
+
+ aliases {
+ i2c7 = &i2c_max77836;
+ };
+
+ memory {
+ reg = <0x40000000 0x1ff00000>;
+ };
+
+ chosen {
+ bootargs = "console=ttySAC1,115200N8 root=/dev/mmcblk0p15 rootwait earlyprintk panic=5";
+ };
+
+ firmware at 0205F000 {
+ compatible = "samsung,secure-firmware";
+ reg = <0x0205F000 0x1000>;
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ power_key {
+ interrupt-parent = <&gpx2>;
+ interrupts = <7 0>;
+ gpios = <&gpx2 7 1>;
+ linux,code = <KEY_POWER>;
+ label = "power key";
+ debounce-interval = <10>;
+ gpio-key,wakeup;
+ };
+ };
+
+ vemmc_reg: voltage-regulator-0 {
+ compatible = "regulator-fixed";
+ regulator-name = "V_EMMC_2.8V-fixed";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ gpio = <&gpk0 2 0>;
+ enable-active-high;
+ };
+
+ i2c_max77836: i2c-gpio-0 {
+ compatible = "i2c-gpio";
+ gpios = <&gpd0 2 0>, <&gpd0 3 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ max77836: subpmic at 25 {
+ compatible = "maxim,max77836";
+ interrupt-parent = <&gpx1>;
+ interrupts = <5 0>;
+ reg = <0x25>;
+ wakeup;
+
+ muic: max77836-muic {
+ compatible = "maxim,max77836-muic";
+ };
+
+ regulators {
+ compatible = "maxim,max77836-regulator";
+ safeout_reg: SAFEOUT {
+ regulator-name = "SAFEOUT";
+ };
+
+ charger_reg: CHARGER {
+ regulator-name = "CHARGER";
+ regulator-min-microamp = <45000>;
+ regulator-max-microamp = <475000>;
+ regulator-boot-on;
+ };
+
+ motor_reg: LDO1 {
+ regulator-name = "MOT_2.7V";
+ regulator-min-microvolt = <1100000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ LDO2 {
+ regulator-name = "UNUSED_LDO2";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <3950000>;
+ };
+ };
+
+ charger {
+ compatible = "maxim,max77836-charger";
+
+ maxim,constant-uvolt = <4350000>;
+ maxim,fast-charge-uamp = <225000>;
+ maxim,eoc-uamp = <7500>;
+ maxim,ovp-uvolt = <6500000>;
+ };
+ };
+ };
+};
+
+&adc {
+ vdd-supply = <&ldo3_reg>;
+ status = "okay";
+ assigned-clocks = <&cmu CLK_SCLK_TSADC>;
+ assigned-clock-rates = <6000000>;
+
+ thermistor-ap {
+ compatible = "ntc,ncp15wb473";
+ pullup-uv = <1800000>;
+ pullup-ohm = <100000>;
+ pulldown-ohm = <100000>;
+ io-channels = <&adc 0>;
+ };
+
+ thermistor-battery {
+ compatible = "ntc,ncp15wb473";
+ pullup-uv = <1800000>;
+ pullup-ohm = <100000>;
+ pulldown-ohm = <100000>;
+ io-channels = <&adc 1>;
+ };
+};
+
+&i2c_0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <100000>;
+ status = "okay";
+
+ s2mps14_pmic at 66 {
+ compatible = "samsung,s2mps14-pmic";
+ interrupt-parent = <&gpx0>;
+ interrupts = <7 0>;
+ reg = <0x66>;
+ wakeup;
+
+ s2mps14_osc: clocks {
+ compatible = "samsung,s2mps14-clk";
+ #clock-cells = <1>;
+ clock-output-names = "s2mps14_ap", "unused",
+ "s2mps14_bt";
+ };
+
+ regulators {
+ ldo1_reg: LDO1 {
+ regulator-name = "VAP_ALIVE_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo2_reg: LDO2 {
+ regulator-name = "VAP_M1_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ ldo3_reg: LDO3 {
+ regulator-name = "VCC_AP_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo4_reg: LDO4 {
+ regulator-name = "VAP_AVDD_PLL1";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo5_reg: LDO5 {
+ regulator-name = "VAP_PLL_ISO_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo6_reg: LDO6 {
+ regulator-name = "VAP_VMIPI_1.0V";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ ldo7_reg: LDO7 {
+ regulator-name = "VAP_AVDD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo8_reg: LDO8 {
+ regulator-name = "VAP_USB_3.0V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ regulator-always-on;
+ };
+
+ ldo9_reg: LDO9 {
+ regulator-name = "V_LPDDR_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ ldo10_reg: LDO10 {
+ regulator-name = "UNUSED_LDO10";
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+ };
+
+ ldo11_reg: LDO11 {
+ regulator-name = "V_EMMC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ samsung,ext-control-gpios = <&gpk0 2 0>;
+ };
+
+ ldo12_reg: LDO12 {
+ regulator-name = "V_EMMC_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ samsung,ext-control-gpios = <&gpk0 2 0>;
+ };
+
+ ldo13_reg: LDO13 {
+ regulator-name = "CAM_AVDD_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo14_reg: LDO14 {
+ regulator-name = "UNUSED_LDO14";
+ regulator-min-microvolt = <2700000>;
+ regulator-max-microvolt = <2700000>;
+ };
+
+ ldo15_reg: LDO15 {
+ regulator-name = "TSP_AVDD_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo16_reg: LDO16 {
+ regulator-name = "LCD_VDD_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo17_reg: LDO17 {
+ regulator-name = "V_IRLED_3.3V";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ };
+
+ ldo18_reg: LDO18 {
+ regulator-name = "CAM_AF_2.8V";
+ regulator-min-microvolt = <2800000>;
+ regulator-max-microvolt = <2800000>;
+ };
+
+ ldo19_reg: LDO19 {
+ regulator-name = "TSP_VDD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo20_reg: LDO20 {
+ regulator-name = "LCD_VDD_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo21_reg: LDO21 {
+ regulator-name = "CAM_IO_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ };
+
+ ldo22_reg: LDO22 {
+ regulator-name = "CAM_DVDD_1.2V";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ };
+
+ ldo23_reg: LDO23 {
+ regulator-name = "HRM_VCC_1.8V";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ ldo24_reg: LDO24 {
+ regulator-name = "HRM_VCC_3.3V";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ ldo25_reg: LDO25 {
+ regulator-name = "UNUSED_LDO25";
+ regulator-min-microvolt = <3000000>;
+ regulator-max-microvolt = <3000000>;
+ };
+
+ buck1_reg: BUCK1 {
+ regulator-name = "VAP_MIF_1.0V";
+ regulator-min-microvolt = <800000>;
+ regulator-max-microvolt = <900000>;
+ regulator-always-on;
+ };
+
+ buck2_reg: BUCK2 {
+ regulator-name = "VAP_ARM_1.0V";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1150000>;
+ regulator-always-on;
+ };
+
+ buck3_reg: BUCK3 {
+ regulator-name = "VAP_INT3D_1.0V";
+ regulator-min-microvolt = <850000>;
+ regulator-max-microvolt = <1000000>;
+ regulator-always-on;
+ };
+
+ buck4_reg: BUCK4 {
+ regulator-name = "VCC_SUB_1.95V";
+ regulator-min-microvolt = <1950000>;
+ regulator-max-microvolt = <1950000>;
+ regulator-always-on;
+ };
+
+ buck5_reg: BUCK5 {
+ regulator-name = "VCC_SUB_1.35V";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ };
+ };
+ };
+};
+
+&i2c_1 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ samsung,i2c-sda-delay = <100>;
+ samsung,i2c-slave-addr = <0x10>;
+ samsung,i2c-max-bus-freq = <400000>;
+ status = "okay";
+
+ fuelgauge at 36 {
+ compatible = "maxim,max77836-battery";
+ interrupt-parent = <&gpx1>;
+ interrupts = <2 8>;
+ reg = <0x36>;
+ };
+};
+
+&i2s2 {
+ status = "okay";
+};
+
+&mfc {
+ status = "okay";
+};
+
+&mshc_0 {
+ #address-cells = <1>;
+ #size-cells = <0>;
+ num-slots = <1>;
+ broken-cd;
+ non-removable;
+ cap-mmc-highspeed;
+ desc-num = <4>;
+ mmc-hs200-1_8v;
+ card-detect-delay = <200>;
+ vmmc-supply = <&vemmc_reg>;
+ clock-frequency = <100000000>;
+ clock-freq-min-max = <400000 100000000>;
+ samsung,dw-mshc-ciu-div = <1>;
+ samsung,dw-mshc-sdr-timing = <0 1>;
+ samsung,dw-mshc-ddr-timing = <1 2>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&sd0_cmd &sd0_bus1 &sd0_bus4 &sd0_bus8>;
+ bus-width = <8>;
+ status = "okay";
+};
+
+&serial_0 {
+ assigned-clocks = <&cmu CLK_SCLK_UART0>;
+ assigned-clock-rates = <100000000>;
+ status = "okay";
+};
+
+&serial_1 {
+ status = "okay";
+};
+
+&tmu {
+ vtmu-supply = <&ldo7_reg>;
+ status = "okay";
+};
+
+&rtc {
+ clocks = <&cmu CLK_RTC>, <&s2mps14_osc 0>;
+ clock-names = "rtc", "rtc_src";
+ status = "okay";
+};
+
+&xusbxti {
+ clock-frequency = <24000000>;
+};
--
1.8.5.5
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCHv3 2/3] ARM: dts: Add sleep mode pin configuration for exynos3250-rinato
2014-10-24 11:39 [PATCHv3 0/3] ARM: dts: Add new board dts file for Exynos3250-based Rinato board Chanwoo Choi
2014-10-24 11:39 ` [PATCHv3 1/3] ARM: dts: Add " Chanwoo Choi
@ 2014-10-24 11:39 ` Chanwoo Choi
2014-10-24 11:48 ` Tomasz Figa
2014-10-24 11:39 ` [PATCHv3 3/3] ARM: dts: Add sleep mode of regulator for exynos3250-rinato board Chanwoo Choi
2 siblings, 1 reply; 8+ messages in thread
From: Chanwoo Choi @ 2014-10-24 11:39 UTC (permalink / raw)
To: linux-arm-kernel
This patch add sleep mode pin configuration using pinctrl subsystem
to reduce leakage power-consumption of gpio pin in sleep state.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <Kyungmin Park@samsung.com>
---
arch/arm/boot/dts/exynos3250-pinctrl.dtsi | 16 ++++
arch/arm/boot/dts/exynos3250-rinato.dts | 154 ++++++++++++++++++++++++++++++
2 files changed, 170 insertions(+)
diff --git a/arch/arm/boot/dts/exynos3250-pinctrl.dtsi b/arch/arm/boot/dts/exynos3250-pinctrl.dtsi
index 47b92c1..5ab81c3 100644
--- a/arch/arm/boot/dts/exynos3250-pinctrl.dtsi
+++ b/arch/arm/boot/dts/exynos3250-pinctrl.dtsi
@@ -12,6 +12,22 @@
* published by the Free Software Foundation.
*/
+#define PIN_PULL_NONE 0
+#define PIN_PULL_DOWN 1
+#define PIN_PULL_UP 3
+
+#define PIN_PDN_OUT0 0
+#define PIN_PDN_OUT1 1
+#define PIN_PDN_INPUT 2
+#define PIN_PDN_PREV 3
+
+#define PIN_SLP(_pin, _mode, _pull) \
+ _pin { \
+ samsung,pins = #_pin; \
+ samsung,pin-con-pdn = <PIN_PDN_ ##_mode>; \
+ samsung,pin-pud-pdn = <PIN_PULL_ ##_pull>; \
+ }
+
&pinctrl_0 {
gpa0: gpa0 {
gpio-controller;
diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
index be0ba8d..7256eec 100644
--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -431,3 +431,157 @@
&xusbxti {
clock-frequency = <24000000>;
};
+
+&pinctrl_0 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sleep0>;
+
+ sleep0: sleep-state {
+ PIN_SLP(gpa0-0, INPUT, DOWN);
+ PIN_SLP(gpa0-1, INPUT, DOWN);
+ PIN_SLP(gpa0-2, INPUT, DOWN);
+ PIN_SLP(gpa0-3, INPUT, DOWN);
+ PIN_SLP(gpa0-4, INPUT, DOWN);
+ PIN_SLP(gpa0-5, INPUT, DOWN);
+ PIN_SLP(gpa0-6, INPUT, DOWN);
+ PIN_SLP(gpa0-7, INPUT, DOWN);
+
+ PIN_SLP(gpa1-0, INPUT, DOWN);
+ PIN_SLP(gpa1-1, INPUT, DOWN);
+ PIN_SLP(gpa1-2, INPUT, DOWN);
+ PIN_SLP(gpa1-3, INPUT, DOWN);
+ PIN_SLP(gpa1-4, INPUT, DOWN);
+ PIN_SLP(gpa1-5, INPUT, DOWN);
+
+ PIN_SLP(gpb-0, PREV, NONE);
+ PIN_SLP(gpb-1, PREV, NONE);
+ PIN_SLP(gpb-2, PREV, NONE);
+ PIN_SLP(gpb-3, PREV, NONE);
+ PIN_SLP(gpb-4, INPUT, DOWN);
+ PIN_SLP(gpb-5, INPUT, DOWN);
+ PIN_SLP(gpb-6, INPUT, DOWN);
+ PIN_SLP(gpb-7, INPUT, DOWN);
+
+ PIN_SLP(gpc0-0, INPUT, DOWN);
+ PIN_SLP(gpc0-1, INPUT, DOWN);
+ PIN_SLP(gpc0-2, INPUT, DOWN);
+ PIN_SLP(gpc0-3, INPUT, DOWN);
+ PIN_SLP(gpc0-4, INPUT, DOWN);
+
+ PIN_SLP(gpc1-0, INPUT, DOWN);
+ PIN_SLP(gpc1-1, INPUT, DOWN);
+ PIN_SLP(gpc1-2, INPUT, DOWN);
+ PIN_SLP(gpc1-3, INPUT, DOWN);
+ PIN_SLP(gpc1-4, INPUT, DOWN);
+
+ PIN_SLP(gpd0-0, INPUT, DOWN);
+ PIN_SLP(gpd0-1, INPUT, DOWN);
+ PIN_SLP(gpd0-2, INPUT, NONE);
+ PIN_SLP(gpd0-3, INPUT, NONE);
+
+ PIN_SLP(gpd1-0, INPUT, NONE);
+ PIN_SLP(gpd1-1, INPUT, NONE);
+ PIN_SLP(gpd1-2, INPUT, NONE);
+ PIN_SLP(gpd1-3, INPUT, NONE);
+ };
+};
+
+&pinctrl_1 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&sleep1>;
+
+ sleep1: sleep-state {
+ PIN_SLP(gpe0-0, PREV, NONE);
+ PIN_SLP(gpe0-1, PREV, NONE);
+ PIN_SLP(gpe0-2, INPUT, DOWN);
+ PIN_SLP(gpe0-3, INPUT, UP);
+ PIN_SLP(gpe0-4, INPUT, DOWN);
+ PIN_SLP(gpe0-5, INPUT, DOWN);
+ PIN_SLP(gpe0-6, INPUT, DOWN);
+ PIN_SLP(gpe0-7, INPUT, DOWN);
+
+ PIN_SLP(gpe1-0, INPUT, DOWN);
+ PIN_SLP(gpe1-1, PREV, NONE);
+ PIN_SLP(gpe1-2, INPUT, DOWN);
+ PIN_SLP(gpe1-3, INPUT, DOWN);
+ PIN_SLP(gpe1-4, INPUT, DOWN);
+ PIN_SLP(gpe1-5, INPUT, DOWN);
+ PIN_SLP(gpe1-6, INPUT, DOWN);
+ PIN_SLP(gpe1-7, INPUT, NONE);
+
+ PIN_SLP(gpe2-0, INPUT, NONE);
+ PIN_SLP(gpe2-1, INPUT, NONE);
+ PIN_SLP(gpe2-2, INPUT, NONE);
+
+ PIN_SLP(gpk0-0, INPUT, DOWN);
+ PIN_SLP(gpk0-1, INPUT, DOWN);
+ PIN_SLP(gpk0-2, OUT0, NONE);
+ PIN_SLP(gpk0-3, INPUT, DOWN);
+ PIN_SLP(gpk0-4, INPUT, DOWN);
+ PIN_SLP(gpk0-5, INPUT, DOWN);
+ PIN_SLP(gpk0-6, INPUT, DOWN);
+ PIN_SLP(gpk0-7, INPUT, DOWN);
+
+ PIN_SLP(gpk1-0, INPUT, DOWN);
+ PIN_SLP(gpk1-1, INPUT, DOWN);
+ PIN_SLP(gpk1-2, INPUT, DOWN);
+ PIN_SLP(gpk1-3, INPUT, DOWN);
+ PIN_SLP(gpk1-4, INPUT, DOWN);
+ PIN_SLP(gpk1-5, INPUT, DOWN);
+ PIN_SLP(gpk1-6, INPUT, DOWN);
+
+ PIN_SLP(gpk2-0, INPUT, DOWN);
+ PIN_SLP(gpk2-1, INPUT, DOWN);
+ PIN_SLP(gpk2-2, INPUT, DOWN);
+ PIN_SLP(gpk2-3, INPUT, DOWN);
+ PIN_SLP(gpk2-4, INPUT, DOWN);
+ PIN_SLP(gpk2-5, INPUT, DOWN);
+ PIN_SLP(gpk2-6, INPUT, DOWN);
+
+ PIN_SLP(gpl0-0, INPUT, DOWN);
+ PIN_SLP(gpl0-1, INPUT, DOWN);
+ PIN_SLP(gpl0-2, INPUT, DOWN);
+ PIN_SLP(gpl0-3, INPUT, DOWN);
+
+ PIN_SLP(gpm0-0, INPUT, DOWN);
+ PIN_SLP(gpm0-1, INPUT, DOWN);
+ PIN_SLP(gpm0-2, INPUT, DOWN);
+ PIN_SLP(gpm0-3, INPUT, DOWN);
+ PIN_SLP(gpm0-4, INPUT, DOWN);
+ PIN_SLP(gpm0-5, INPUT, DOWN);
+ PIN_SLP(gpm0-6, INPUT, DOWN);
+ PIN_SLP(gpm0-7, INPUT, DOWN);
+
+ PIN_SLP(gpm1-0, INPUT, DOWN);
+ PIN_SLP(gpm1-1, INPUT, DOWN);
+ PIN_SLP(gpm1-2, INPUT, DOWN);
+ PIN_SLP(gpm1-3, INPUT, DOWN);
+ PIN_SLP(gpm1-4, INPUT, DOWN);
+ PIN_SLP(gpm1-5, INPUT, DOWN);
+ PIN_SLP(gpm1-6, INPUT, DOWN);
+
+ PIN_SLP(gpm2-0, INPUT, DOWN);
+ PIN_SLP(gpm2-1, INPUT, DOWN);
+ PIN_SLP(gpm2-2, INPUT, DOWN);
+ PIN_SLP(gpm2-3, INPUT, DOWN);
+ PIN_SLP(gpm2-4, INPUT, DOWN);
+
+ PIN_SLP(gpm3-0, INPUT, DOWN);
+ PIN_SLP(gpm3-1, INPUT, DOWN);
+ PIN_SLP(gpm3-2, INPUT, DOWN);
+ PIN_SLP(gpm3-3, INPUT, DOWN);
+ PIN_SLP(gpm3-4, INPUT, DOWN);
+ PIN_SLP(gpm3-5, INPUT, DOWN);
+ PIN_SLP(gpm3-6, INPUT, DOWN);
+ PIN_SLP(gpm3-7, INPUT, DOWN);
+
+ PIN_SLP(gpm4-0, INPUT, DOWN);
+ PIN_SLP(gpm4-1, INPUT, DOWN);
+ PIN_SLP(gpm4-2, INPUT, DOWN);
+ PIN_SLP(gpm4-3, INPUT, DOWN);
+ PIN_SLP(gpm4-4, INPUT, DOWN);
+ PIN_SLP(gpm4-5, INPUT, DOWN);
+ PIN_SLP(gpm4-6, INPUT, DOWN);
+ PIN_SLP(gpm4-7, INPUT, DOWN);
+ };
+};
--
1.8.5.5
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCHv3 3/3] ARM: dts: Add sleep mode of regulator for exynos3250-rinato board
2014-10-24 11:39 [PATCHv3 0/3] ARM: dts: Add new board dts file for Exynos3250-based Rinato board Chanwoo Choi
2014-10-24 11:39 ` [PATCHv3 1/3] ARM: dts: Add " Chanwoo Choi
2014-10-24 11:39 ` [PATCHv3 2/3] ARM: dts: Add sleep mode pin configuration for exynos3250-rinato Chanwoo Choi
@ 2014-10-24 11:39 ` Chanwoo Choi
2 siblings, 0 replies; 8+ messages in thread
From: Chanwoo Choi @ 2014-10-24 11:39 UTC (permalink / raw)
To: linux-arm-kernel
This patch add sleep mode of regulator for exynos3250-rinato board to optimize
power-consumption in sleep state.
Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Reviewed-by: Mark Brown <broonie@kernel.org>
---
arch/arm/boot/dts/exynos3250-rinato.dts | 108 ++++++++++++++++++++++++++++++++
1 file changed, 108 insertions(+)
diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
index 7256eec..8e828bc 100644
--- a/arch/arm/boot/dts/exynos3250-rinato.dts
+++ b/arch/arm/boot/dts/exynos3250-rinato.dts
@@ -166,6 +166,10 @@
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
};
ldo2_reg: LDO2 {
@@ -173,6 +177,10 @@
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo3_reg: LDO3 {
@@ -180,6 +188,10 @@
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo4_reg: LDO4 {
@@ -187,6 +199,10 @@
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo5_reg: LDO5 {
@@ -194,6 +210,10 @@
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo6_reg: LDO6 {
@@ -201,6 +221,10 @@
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo7_reg: LDO7 {
@@ -208,6 +232,10 @@
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo8_reg: LDO8 {
@@ -215,6 +243,10 @@
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo9_reg: LDO9 {
@@ -222,12 +254,20 @@
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
regulator-always-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
};
ldo10_reg: LDO10 {
regulator-name = "UNUSED_LDO10";
regulator-min-microvolt = <1000000>;
regulator-max-microvolt = <1000000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo11_reg: LDO11 {
@@ -248,60 +288,100 @@
regulator-name = "CAM_AVDD_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo14_reg: LDO14 {
regulator-name = "UNUSED_LDO14";
regulator-min-microvolt = <2700000>;
regulator-max-microvolt = <2700000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo15_reg: LDO15 {
regulator-name = "TSP_AVDD_3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo16_reg: LDO16 {
regulator-name = "LCD_VDD_3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo17_reg: LDO17 {
regulator-name = "V_IRLED_3.3V";
regulator-min-microvolt = <3300000>;
regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo18_reg: LDO18 {
regulator-name = "CAM_AF_2.8V";
regulator-min-microvolt = <2800000>;
regulator-max-microvolt = <2800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo19_reg: LDO19 {
regulator-name = "TSP_VDD_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo20_reg: LDO20 {
regulator-name = "LCD_VDD_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo21_reg: LDO21 {
regulator-name = "CAM_IO_1.8V";
regulator-min-microvolt = <1800000>;
regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo22_reg: LDO22 {
regulator-name = "CAM_DVDD_1.2V";
regulator-min-microvolt = <1200000>;
regulator-max-microvolt = <1200000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo23_reg: LDO23 {
@@ -315,12 +395,20 @@
regulator-name = "HRM_VCC_3.3V";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
ldo25_reg: LDO25 {
regulator-name = "UNUSED_LDO25";
regulator-min-microvolt = <3000000>;
regulator-max-microvolt = <3000000>;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
buck1_reg: BUCK1 {
@@ -328,6 +416,10 @@
regulator-min-microvolt = <800000>;
regulator-max-microvolt = <900000>;
regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
buck2_reg: BUCK2 {
@@ -335,6 +427,10 @@
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <1150000>;
regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
buck3_reg: BUCK3 {
@@ -342,6 +438,10 @@
regulator-min-microvolt = <850000>;
regulator-max-microvolt = <1000000>;
regulator-always-on;
+
+ regulator-state-mem {
+ regulator-off-in-suspend;
+ };
};
buck4_reg: BUCK4 {
@@ -349,6 +449,10 @@
regulator-min-microvolt = <1950000>;
regulator-max-microvolt = <1950000>;
regulator-always-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
};
buck5_reg: BUCK5 {
@@ -356,6 +460,10 @@
regulator-min-microvolt = <1350000>;
regulator-max-microvolt = <1350000>;
regulator-always-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
};
};
};
--
1.8.5.5
^ permalink raw reply related [flat|nested] 8+ messages in thread
* [PATCHv3 2/3] ARM: dts: Add sleep mode pin configuration for exynos3250-rinato
2014-10-24 11:39 ` [PATCHv3 2/3] ARM: dts: Add sleep mode pin configuration for exynos3250-rinato Chanwoo Choi
@ 2014-10-24 11:48 ` Tomasz Figa
2014-10-24 11:53 ` Chanwoo Choi
0 siblings, 1 reply; 8+ messages in thread
From: Tomasz Figa @ 2014-10-24 11:48 UTC (permalink / raw)
To: linux-arm-kernel
Hi Chanwoo,
On 24.10.2014 13:39, Chanwoo Choi wrote:
> This patch add sleep mode pin configuration using pinctrl subsystem
> to reduce leakage power-consumption of gpio pin in sleep state.
>
> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
> Acked-by: Kyungmin Park <Kyungmin Park@samsung.com>
I suspect a typo in this email address. Kukjin, is this something you
could fix up when applying (other patches in this series have it correct)?
Best regards,
Tomasz
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCHv3 2/3] ARM: dts: Add sleep mode pin configuration for exynos3250-rinato
2014-10-24 11:48 ` Tomasz Figa
@ 2014-10-24 11:53 ` Chanwoo Choi
0 siblings, 0 replies; 8+ messages in thread
From: Chanwoo Choi @ 2014-10-24 11:53 UTC (permalink / raw)
To: linux-arm-kernel
Hi Tomasz,
On 10/24/2014 08:48 PM, Tomasz Figa wrote:
> Hi Chanwoo,
>
> On 24.10.2014 13:39, Chanwoo Choi wrote:
>> This patch add sleep mode pin configuration using pinctrl subsystem
>> to reduce leakage power-consumption of gpio pin in sleep state.
>>
>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>> Acked-by: Kyungmin Park <Kyungmin Park@samsung.com>
>
> I suspect a typo in this email address. Kukjin, is this something you
> could fix up when applying (other patches in this series have it correct)?
Sorry about my mistake. I'll resend it right now.
Best Regards,
Chanwoo Choi
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCHv3 1/3] ARM: dts: Add board dts file for Exynos3250-based Rinato board
2014-10-24 11:39 ` [PATCHv3 1/3] ARM: dts: Add " Chanwoo Choi
@ 2014-10-24 11:57 ` Krzysztof Kozłowski
2014-10-24 12:13 ` Chanwoo Choi
0 siblings, 1 reply; 8+ messages in thread
From: Krzysztof Kozłowski @ 2014-10-24 11:57 UTC (permalink / raw)
To: linux-arm-kernel
On 24.10.2014 13:39, Chanwoo Choi wrote:
> This patch add support for device tree sources for Samsung Rinato baord
> (Gear 2) based on Exynos3250 SoC.
>
> This dts file support following features:
> - eMMC
> - Main PMIC (Samsung S2MPS14)
> - Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
> - RTC of Exynos3250
> - ADC of Exynos3250 with NTC thermistor
> - I2S of Exynos3250
> - TMU of Exynos3250
> - MFC of Exynos3250
> - Secure firmware for Exynos3250 secondary cpu boot
> - Serial ports of Exynos3250
> - gpio-key for power key
>
> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
> Signed-off-by: Inki Dae <inki.dae@samsung.com>
> Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
> ---
> arch/arm/boot/dts/Makefile | 3 +-
> arch/arm/boot/dts/exynos3250-rinato.dts | 433 ++++++++++++++++++++++++++++++++
> 2 files changed, 435 insertions(+), 1 deletion(-)
> create mode 100644 arch/arm/boot/dts/exynos3250-rinato.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 4a75e29..91cd4d0 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -67,7 +67,8 @@ dtb-$(CONFIG_ARCH_BRCMSTB) += \
> dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \
> da850-evm.dtb
> dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb
> -dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
> +dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-rinato.dtb \
> + exynos4210-origen.dtb \
> exynos4210-smdkv310.dtb \
> exynos4210-trats.dtb \
> exynos4210-universal_c210.dtb \
> diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
> new file mode 100644
> index 0000000..be0ba8d
> --- /dev/null
> +++ b/arch/arm/boot/dts/exynos3250-rinato.dts
> @@ -0,0 +1,433 @@
> +/*
> + * Samsung's Exynos3250 based Rinato board device tree source
> + *
> + * Copyright (c) 2014 Samsung Electronics Co., Ltd.
> + * http://www.samsung.com
> + *
> + * Device tree source file for Samsung's Rinato board which is based on
> + * Samsung Exynos3250 SoC.
> + *
> + * This program is free software; you can redistribute it and/or modify
> + * it under the terms of the GNU General Public License version 2 as
> + * published by the Free Software Foundation.
> + */
> +
> +/dts-v1/;
> +#include "exynos3250.dtsi"
> +#include <dt-bindings/input/input.h>
> +
> +/ {
> + model = "Samsung Rinato board";
> + compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3";
> +
> + aliases {
> + i2c7 = &i2c_max77836;
> + };
> +
> + memory {
> + reg = <0x40000000 0x1ff00000>;
> + };
> +
> + chosen {
> + bootargs = "console=ttySAC1,115200N8 root=/dev/mmcblk0p15 rootwait earlyprintk panic=5";
> + };
> +
> + firmware at 0205F000 {
> + compatible = "samsung,secure-firmware";
> + reg = <0x0205F000 0x1000>;
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> +
> + power_key {
> + interrupt-parent = <&gpx2>;
> + interrupts = <7 0>;
> + gpios = <&gpx2 7 1>;
> + linux,code = <KEY_POWER>;
> + label = "power key";
> + debounce-interval = <10>;
> + gpio-key,wakeup;
> + };
> + };
> +
> + vemmc_reg: voltage-regulator-0 {
> + compatible = "regulator-fixed";
> + regulator-name = "V_EMMC_2.8V-fixed";
> + regulator-min-microvolt = <2800000>;
> + regulator-max-microvolt = <2800000>;
> + gpio = <&gpk0 2 0>;
> + enable-active-high;
> + };
Hi Chanwoo,
I wonder if this regulator-fixed is needed. The LDO11 and LDO12 has
external GPIO control set up. So maybe this could be removed?
Best regards,
Krzysztof
^ permalink raw reply [flat|nested] 8+ messages in thread
* [PATCHv3 1/3] ARM: dts: Add board dts file for Exynos3250-based Rinato board
2014-10-24 11:57 ` Krzysztof Kozłowski
@ 2014-10-24 12:13 ` Chanwoo Choi
0 siblings, 0 replies; 8+ messages in thread
From: Chanwoo Choi @ 2014-10-24 12:13 UTC (permalink / raw)
To: linux-arm-kernel
Hi Krzysztof,
On 10/24/2014 08:57 PM, Krzysztof Koz?owski wrote:
> On 24.10.2014 13:39, Chanwoo Choi wrote:
>> This patch add support for device tree sources for Samsung Rinato baord
>> (Gear 2) based on Exynos3250 SoC.
>>
>> This dts file support following features:
>> - eMMC
>> - Main PMIC (Samsung S2MPS14)
>> - Interface PMIC (Maxim MAX77836, MUIC, fuel-gauge, charger)
>> - RTC of Exynos3250
>> - ADC of Exynos3250 with NTC thermistor
>> - I2S of Exynos3250
>> - TMU of Exynos3250
>> - MFC of Exynos3250
>> - Secure firmware for Exynos3250 secondary cpu boot
>> - Serial ports of Exynos3250
>> - gpio-key for power key
>>
>> Signed-off-by: Chanwoo Choi <cw00.choi@samsung.com>
>> Signed-off-by: Inki Dae <inki.dae@samsung.com>
>> Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
>> Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
>> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com>
>> ---
>> arch/arm/boot/dts/Makefile | 3 +-
>> arch/arm/boot/dts/exynos3250-rinato.dts | 433 ++++++++++++++++++++++++++++++++
>> 2 files changed, 435 insertions(+), 1 deletion(-)
>> create mode 100644 arch/arm/boot/dts/exynos3250-rinato.dts
>>
>> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
>> index 4a75e29..91cd4d0 100644
>> --- a/arch/arm/boot/dts/Makefile
>> +++ b/arch/arm/boot/dts/Makefile
>> @@ -67,7 +67,8 @@ dtb-$(CONFIG_ARCH_BRCMSTB) += \
>> dtb-$(CONFIG_ARCH_DAVINCI) += da850-enbw-cmc.dtb \
>> da850-evm.dtb
>> dtb-$(CONFIG_ARCH_EFM32) += efm32gg-dk3750.dtb
>> -dtb-$(CONFIG_ARCH_EXYNOS) += exynos4210-origen.dtb \
>> +dtb-$(CONFIG_ARCH_EXYNOS) += exynos3250-rinato.dtb \
>> + exynos4210-origen.dtb \
>> exynos4210-smdkv310.dtb \
>> exynos4210-trats.dtb \
>> exynos4210-universal_c210.dtb \
>> diff --git a/arch/arm/boot/dts/exynos3250-rinato.dts b/arch/arm/boot/dts/exynos3250-rinato.dts
>> new file mode 100644
>> index 0000000..be0ba8d
>> --- /dev/null
>> +++ b/arch/arm/boot/dts/exynos3250-rinato.dts
>> @@ -0,0 +1,433 @@
>> +/*
>> + * Samsung's Exynos3250 based Rinato board device tree source
>> + *
>> + * Copyright (c) 2014 Samsung Electronics Co., Ltd.
>> + * http://www.samsung.com
>> + *
>> + * Device tree source file for Samsung's Rinato board which is based on
>> + * Samsung Exynos3250 SoC.
>> + *
>> + * This program is free software; you can redistribute it and/or modify
>> + * it under the terms of the GNU General Public License version 2 as
>> + * published by the Free Software Foundation.
>> + */
>> +
>> +/dts-v1/;
>> +#include "exynos3250.dtsi"
>> +#include <dt-bindings/input/input.h>
>> +
>> +/ {
>> + model = "Samsung Rinato board";
>> + compatible = "samsung,rinato", "samsung,exynos3250", "samsung,exynos3";
>> +
>> + aliases {
>> + i2c7 = &i2c_max77836;
>> + };
>> +
>> + memory {
>> + reg = <0x40000000 0x1ff00000>;
>> + };
>> +
>> + chosen {
>> + bootargs = "console=ttySAC1,115200N8 root=/dev/mmcblk0p15 rootwait earlyprintk panic=5";
>> + };
>> +
>> + firmware at 0205F000 {
>> + compatible = "samsung,secure-firmware";
>> + reg = <0x0205F000 0x1000>;
>> + };
>> +
>> + gpio_keys {
>> + compatible = "gpio-keys";
>> +
>> + power_key {
>> + interrupt-parent = <&gpx2>;
>> + interrupts = <7 0>;
>> + gpios = <&gpx2 7 1>;
>> + linux,code = <KEY_POWER>;
>> + label = "power key";
>> + debounce-interval = <10>;
>> + gpio-key,wakeup;
>> + };
>> + };
>> +
>> + vemmc_reg: voltage-regulator-0 {
>> + compatible = "regulator-fixed";
>> + regulator-name = "V_EMMC_2.8V-fixed";
>> + regulator-min-microvolt = <2800000>;
>> + regulator-max-microvolt = <2800000>;
>> + gpio = <&gpk0 2 0>;
>> + enable-active-high;
>> + };
>
> Hi Chanwoo,
>
> I wonder if this regulator-fixed is needed. The LDO11 and LDO12 has
> external GPIO control set up. So maybe this could be removed?
OK, I'll remove 'vemmc_reg' and then use ldo12_reg insead of 'vemmc_reg' on mshc_0 dt node.
Best Regards,
Chanwoo Choi
^ permalink raw reply [flat|nested] 8+ messages in thread
end of thread, other threads:[~2014-10-24 12:13 UTC | newest]
Thread overview: 8+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2014-10-24 11:39 [PATCHv3 0/3] ARM: dts: Add new board dts file for Exynos3250-based Rinato board Chanwoo Choi
2014-10-24 11:39 ` [PATCHv3 1/3] ARM: dts: Add " Chanwoo Choi
2014-10-24 11:57 ` Krzysztof Kozłowski
2014-10-24 12:13 ` Chanwoo Choi
2014-10-24 11:39 ` [PATCHv3 2/3] ARM: dts: Add sleep mode pin configuration for exynos3250-rinato Chanwoo Choi
2014-10-24 11:48 ` Tomasz Figa
2014-10-24 11:53 ` Chanwoo Choi
2014-10-24 11:39 ` [PATCHv3 3/3] ARM: dts: Add sleep mode of regulator for exynos3250-rinato board Chanwoo Choi
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).