From mboxrd@z Thu Jan  1 00:00:00 1970
From: sebastian.hesselbarth@gmail.com (Sebastian Hesselbarth)
Date: Wed, 12 Nov 2014 00:23:07 +0100
Subject: [PATCH v3 4/5] ARM: berlin: Add AHCI and SATA PHY nodes to BG2
In-Reply-To: <1414664488-5911-5-git-send-email-sebastian.hesselbarth@gmail.com>
References: <1413882477-27922-1-git-send-email-sebastian.hesselbarth@gmail.com>
 <1414664488-5911-1-git-send-email-sebastian.hesselbarth@gmail.com>
 <1414664488-5911-5-git-send-email-sebastian.hesselbarth@gmail.com>
Message-ID: <54629A5B.9050209@gmail.com>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

On 30.10.2014 11:21, Sebastian Hesselbarth wrote:
> Add DT nodes for the AHCI controller and SATA PHY found on Marvell
> Berlin2 SoCs.
>
> Acked-by: Antoine T?nart <antoine.tenart@free-electrons.com>
> Signed-off-by: Sebastian Hesselbarth <sebastian.hesselbarth@gmail.com>

Applied both DT patches to berlin/dt.

Sebastian

> ---
>   arch/arm/boot/dts/berlin2.dtsi | 39 +++++++++++++++++++++++++++++++++++++++
>   1 file changed, 39 insertions(+)
>
> diff --git a/arch/arm/boot/dts/berlin2.dtsi b/arch/arm/boot/dts/berlin2.dtsi
> index 9d7c810ebd0b..f39090491eb2 100644
> --- a/arch/arm/boot/dts/berlin2.dtsi
> +++ b/arch/arm/boot/dts/berlin2.dtsi
> @@ -246,6 +246,45 @@
>   			};
>   		};
>
> +		ahci: sata at e90000 {
> +			compatible = "marvell,berlin2-ahci", "generic-ahci";
> +			reg = <0xe90000 0x1000>;
> +			interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH>;
> +			clocks = <&chip CLKID_SATA>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			sata0: sata-port at 0 {
> +				reg = <0>;
> +				phys = <&sata_phy 0>;
> +				status = "disabled";
> +			};
> +
> +			sata1: sata-port at 1 {
> +				reg = <1>;
> +				phys = <&sata_phy 1>;
> +				status = "disabled";
> +			};
> +		};
> +
> +		sata_phy: phy at e900a0 {
> +			compatible = "marvell,berlin2-sata-phy";
> +			reg = <0xe900a0 0x200>;
> +			clocks = <&chip CLKID_SATA>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +			#phy-cells = <1>;
> +			status = "disabled";
> +
> +			sata-phy at 0 {
> +				reg = <0>;
> +			};
> +
> +			sata-phy at 1 {
> +				reg = <1>;
> +			};
> +		};
> +
>   		chip: chip-control at ea0000 {
>   			compatible = "marvell,berlin2-chip-ctrl";
>   			#clock-cells = <1>;
>