[PATCH] ARM: exynos_defconfig: disable CONFIG_EXYNOS5420_MCPM; not stable

[kgene@kernel.org (Kukjin Kim)]

On 11/27/14 02:56, Kevin Hilman wrote:
> Abhilash Kesavan <kesavan.abhilash@gmail.com> writes:
> 
>> Hi Kevin,
>>
>> On Wed, Nov 26, 2014 at 6:30 AM, Kevin Hilman <khilman@kernel.org> wrote:
>>> Hi Abhilash,
>>>
>>> Abhilash Kesavan <kesavan.abhilash@gmail.com> writes:
>>>
>>> [...]
>>>
>>>>>> To be honest, since I don't have the exynos5420 arndale, chromebook...but smdk
>>>>>> which has different bootloader, I couldn't test it...I'll try to make a test
>>>>>> farm like you guys...
>>>>>
>>>>> Do you have some colleagues with any other 542x hardware?  I had
>>>>> assumed that linux-next was being better tested on the publicaly
>>>>> available, and widely available boards like odroid-xu3 and
>>>>> Chromebook2, but I've come to realize the hard way that that is not
>>>>
>>>> Are you seeing this on Chromebook2 (Peach-Pi 5800) too ?
>>>
>>> No, it seems that my exynos5800-peach-pi is not having this problem,
>>> which suggests it's a bootloader setup issue.
>>>
>>>>> the case.  You mention your board has a different bootloader.  Do you
>>>>> suspect there's a bootloader issue on these other platforms?  If so,
>>>>> could you elaborate on possible fixes?  I'm more than willing to test
>>>>> any proposed fixes, but I'm not familiar enough yet with these SoCs to
>>>>> figure out the underlying issues alone.
>>>>>
>>>>> Until you have a working board farm, you could start having a closer
>>>>> look at the boot logs we're already producing.  Admittedly linux-next
>>>>> broken in many ways besides this one for exynos currently, but it has
>>>>> been having these imprecise aborts well before the other recent
>>>>> issues.
>>>>>
>>>>> Also, It's very possible that this issue is not even MCPM related at
>>>>> all, and MCPM is just uncovering a previously hidden bug.  It would be
>>>>> very helpful if people more familiar with this hardware and SoC would
>>>>> investigate bug reports like these.
>>>>
>>>> The 3 boards I have access to (SMDK5420, Chromebook Peach-Pi and
>>>> Chromebook Peach-Pit) work fine with MCPM enabled.
>>>
>>> Thanks for helping look into this.
>>>
>>>> I am not sure why
>>>> it is failing only on the above mentioned boards as there is nothing
>>>> specific to them in the MCPM back-end.
>>>>
>>>> I assume that when you default to platsmp (on disabling MCPM), the
>>>> non-working boards boot all cores upto userspace without any issues ?
>>>
>>> Nope.  With MCPM disabled:
>>>
>>>   - 5420/arndale-octa: CPU0-3 come up (A15s)
>>>   - 5422/odroid-xu3: only CPU0 (A7)
>>>   - 5800/peach-pi: only CPU0 (A15)
>>>
>>> Note that with MCPM enabled, the arndale-octa gets the same result.
>>> Peach-pi on the other hand gets all 8 CPUs, and the odroid-xu3 only gets
>>> 6/8 CPUs (see other thread on that topic.)
>>>
>>>> Based on the timeline (problems started about 2.5 months back), there
>>>> have only been a couple of changes in the 5420 MCPM back-end. Could
>>>> you revert the following commits and check if things improve.
>>>>
>>>> 20fe6f9 ARM: EXYNOS: Support cluster power off on exynos5420/5800
>>>> fbb0499 ARM: 8083/1: exynos: activate the CCI on boot CPU/cluster
>>>> using the MCPM loopback
>>>>
>>>> These might not revert cleanly, so instead of the above you could also
>>>> comment the following 2 lines:
>>>>
>>>>
>>>> diff --git a/arch/arm/mach-exynos/mcpm-exynos.c
>>>> b/arch/arm/mach-exynos/mcpm-exynos.c
>>>> index dc9a764..9a07188 100644
>>>> --- a/arch/arm/mach-exynos/mcpm-exynos.c
>>>> +++ b/arch/arm/mach-exynos/mcpm-exynos.c
>>>> @@ -152,7 +152,7 @@ static void exynos_power_down(void)
>>>>                 exynos_cpu_power_down(cpunr);
>>>>
>>>>                 if (exynos_cluster_unused(cluster)) {
>>>> -                       exynos_cluster_power_down(cluster);
>>>> +                       //exynos_cluster_power_down(cluster);
>>>>                         last_man = true;
>>>>                 }
>>> 2>         } else if (cpu_use_count[cpu][cluster] == 1) {
>>>> @@ -356,8 +356,8 @@ static int __init exynos_mcpm_init(void)
>>>>         ret = mcpm_platform_register(&exynos_power_ops);
>>>>         if (!ret)
>>>>                 ret = mcpm_sync_init(exynos_pm_power_up_setup);
>>>> -       if (!ret)
>>>> -               ret = mcpm_loopback(exynos_cache_off); /* turn on the CCI */
>>>> +       //if (!ret)
>>>> +               //ret = mcpm_loopback(exynos_cache_off); /* turn on the CCI */
>>>>         if (ret) {
>>>>                 iounmap(ns_sram_base_addr);
>>>>                 return ret;
>>>>
>>>>
>>>>
>>>> If you still get aborts then I suspect that the problem is with the
>>>> bootloader configuration but am not sure.
>>>
>>> Nice.  With those lines commented out, the arndale-octa is not geting
>>> imprecise aborts anymore, and this is the platform where those aborts
>>> seem to prevent booting into a full userspace (as originally reported by
>>> Tyler.)
>>>
>>> More specifically, with only the loopback call to turn off CCI commented
>>> out, the imprecise aborts go away.
>>
>> I can't see how enabling snoops for the boot cluster is causing these
>> aborts. Perhaps as Krzysztof commented it has something to do with the
>> secure firmware/tz software on these boards ? Other than there does
>> not appear to be any difference between the working/non-working
>> setups.
> 
> Perhaps the secure firmware is preventing the CCI to be enabled by the
> kernel, and that is causing the imprecise abort?
> 
> Is there a way to update/replace the BL1/BL2/TZ firmware blobs with
> something that is known to be working better?  
> 
Seems current problem you mentioned is due to different bootloader as I
commented before, but to release bootloader images (bl1, bl2 and so on)
should be handled by board manufacture not SoC vendor I think...even
though the images are provided by vendor for manufacture. To be honest
I'm not sure what procedure should be passed in Samsung side for now
because we including Abhilash are belong to just development team. Need
some time but I can't confirm that...sorry. Let us try.

BTW, Kevin do you know current version for bootloader images on the boards?

Thanks,
Kukjin