From mboxrd@z Thu Jan  1 00:00:00 1970
From: kgene@kernel.org (Kukjin Kim)
Date: Thu, 15 Jan 2015 00:55:44 +0900
Subject: [PATCH] ARM: dts: exynos5422-odroidxu3: add INA2xx sensors
In-Reply-To: <1421193801-24637-1-git-send-email-khilman@kernel.org>
References: <1421193801-24637-1-git-send-email-khilman@kernel.org>
Message-ID: <54B69180.2010403@kernel.org>
To: linux-arm-kernel@lists.infradead.org
List-Id: linux-arm-kernel.lists.infradead.org

On 01/14/15 09:03, Kevin Hilman wrote:
> From: Kevin Hilman <khilman@linaro.org>
> 
> The odroid-xu3 has 4 INA231 current sensors on board which can be
> accessed from the Linux via the hwmon interface.
> 
> There is one sensor for each of these power rails:
> 
> - A15 cluster: VDD_ARM
> - A7 cluster: VDD_KFC
> - GPU: VDD_G3D
> - memory: VDD_MEM
> 
> In addition to adding the sensors, LDO26 from the PMIC needs to be
> enabled because it's powering these sensor.
> 
> Cc: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
> Cc: Sjoerd Simons <sjoerd.simons@collabora.co.uk>
> Signed-off-by: Kevin Hilman <khilman@linaro.org>
> ---
> Applies on top of "ARM: dts: Add dts file for odroid XU3 board" from Sjoerd Simons.
> 
>  arch/arm/boot/dts/exynos5422-odroidxu3.dts | 39 ++++++++++++++++++++++++++++++
>  1 file changed, 39 insertions(+)
> 
> diff --git a/arch/arm/boot/dts/exynos5422-odroidxu3.dts b/arch/arm/boot/dts/exynos5422-odroidxu3.dts
> index c29123c0734d..7874da20939f 100644
> --- a/arch/arm/boot/dts/exynos5422-odroidxu3.dts
> +++ b/arch/arm/boot/dts/exynos5422-odroidxu3.dts
> @@ -174,6 +174,13 @@
>  					regulator-always-on;
>  				};
>  
> +				ldo26_reg: LDO26 {
> +					regulator-name = "vdd_ldo26";
> +					regulator-min-microvolt = <3000000>;
> +					regulator-max-microvolt = <3000000>;
> +					regulator-always-on;
> +				};
> +
>  				buck1_reg: BUCK1 {
>  					regulator-name = "vdd_mif";
>  					regulator-min-microvolt = <800000>;
> @@ -257,6 +264,38 @@
>  		};
>  	};
>  
> +	i2c_0: i2c at 12C60000 {
> +		status = "okay";
> +
> +		/* A15 cluster: VDD_ARM */
> +		ina220 at 40 {
> +			compatible = "ti,ina230";
> +			reg = <0x40>;
> +			shunt-resistor = <10000>;
> +		};
> +
> +		/* memory: VDD_MEM */
> +		ina220 at 41 {
> +			compatible = "ti,ina230";
> +			reg = <0x41>;
> +			shunt-resistor = <10000>;
> +		};
> +
> +		/* GPU: VDD_G3D */
> +		ina220 at 44 {
> +			compatible = "ti,ina230";
> +			reg = <0x44>;
> +			shunt-resistor = <10000>;
> +		};
> +
> +		/* A7 cluster: VDD_KFC */
> +		ina220 at 45 {
> +			compatible = "ti,ina230";
> +			reg = <0x45>;
> +			shunt-resistor = <10000>;
> +		};
> +	};
> +
>  	i2c_2: i2c at 12C80000 {
>  		samsung,i2c-sda-delay = <100>;
>  		samsung,i2c-max-bus-freq = <66000>;

Looks good to me and applied. To be honest, I'm not sure about the
values in the node of shunt-resistor though ;)

Thanks,
Kukjin