* [PATCH v3] ahci_xgene: Fix the dma state machine lockup for the ATA_CMD_SMART PIO mode command. [not found] ` <1422900439-5541-2-git-send-email-stripathi@apm.com> @ 2015-02-02 19:12 ` Sergei Shtylyov [not found] ` <CAOHikRBMPbyS0q6814+Xkez7ToBwrC7Yzp4sy=NMmPDg-5wCBA@mail.gmail.com> 2015-02-03 16:18 ` Tejun Heo 1 sibling, 1 reply; 5+ messages in thread From: Sergei Shtylyov @ 2015-02-02 19:12 UTC (permalink / raw) To: linux-arm-kernel Hello. On 02/02/2015 09:07 PM, Suman Tripathi wrote: > This patch addresses the issue with ATA_CMD_SMART pio mode > command for enumeration and device detection with ATA devices. > The X-Gene AHCI controller has an errata in which it cannot clear > the BSY bit after the PIO setup FIS. The dma state machine enters Hum, if this happens after every PIO command (PIO setup FISes are not specific to the command, right?), perhaps it would make more sense to record the *protocol* used by the last command? > CMFatalErrorUpdate state and locks up. It is the same issue as > in the commit 2a0bdff6b958d1b2523d2754b6cd5e0ea4053016 (ahci-xgene: > fix the dma state machine lockup for the IDENTIFY DEVICE PIO mode > command). > For example : without this patch it results in READ DMA command failure > as shown below : [...] > Signed-off-by: Suman Tripathi <stripathi@apm.com> > Reported-by: Mark Langsdorf <mlangsdo@redhat.com> MBR, Sergei ^ permalink raw reply [flat|nested] 5+ messages in thread
[parent not found: <CAOHikRBMPbyS0q6814+Xkez7ToBwrC7Yzp4sy=NMmPDg-5wCBA@mail.gmail.com>]
* [PATCH v3] ahci_xgene: Fix the dma state machine lockup for the ATA_CMD_SMART PIO mode command. [not found] ` <CAOHikRBMPbyS0q6814+Xkez7ToBwrC7Yzp4sy=NMmPDg-5wCBA@mail.gmail.com> @ 2015-02-02 19:44 ` Sergei Shtylyov 2015-02-02 19:48 ` Suman Tripathi 0 siblings, 1 reply; 5+ messages in thread From: Sergei Shtylyov @ 2015-02-02 19:44 UTC (permalink / raw) To: linux-arm-kernel On 02/02/2015 10:37 PM, Suman Tripathi wrote: Ugh, please avoid using HTML when posting to the lists hosted on vger.kernel.org -- it's configured to ignore such mails AFAIK. >>> This patch addresses the issue with ATA_CMD_SMART pio mode >>> command for enumeration and device detection with ATA devices. >>> The X-Gene AHCI controller has an errata in which it cannot clear >>> the BSY bit after the PIO setup FIS. The dma state machine enters >> Hum, if this happens after every PIO command (PIO setup FISes are not >> specific to the command, right?), perhaps it would make more sense to record >> the *protocol* used by the last command? > No it happens for IDENTIFY DEVICE, ATA_CMD_PACKET and ATA_CMD_SMART commands . > It is actually the commands associated with a BSY bit clearing. I don't understand that -- BSY bit is cleared for *every* command, either at the end of it, or along with setting the DRQ bit for PIO data transfer. >>> CMFatalErrorUpdate state and locks up. It is the same issue as >>> in the commit 2a0bdff6b958d1b2523d2754b6cd5e__0ea4053016 (ahci-xgene: >>> fix the dma state machine lockup for the IDENTIFY DEVICE PIO mode >>> command). >> [...] >>> Signed-off-by: Suman Tripathi <stripathi at apm.com <mailto:stripathi@apm.com>> >>> Reported-by: Mark Langsdorf <mlangsdo@redhat.com >>> <mailto:mlangsdo@redhat.com>> >>> MBR, Sergei ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v3] ahci_xgene: Fix the dma state machine lockup for the ATA_CMD_SMART PIO mode command. 2015-02-02 19:44 ` Sergei Shtylyov @ 2015-02-02 19:48 ` Suman Tripathi 2015-02-03 16:12 ` Suman Tripathi 0 siblings, 1 reply; 5+ messages in thread From: Suman Tripathi @ 2015-02-02 19:48 UTC (permalink / raw) To: linux-arm-kernel Ugh, please avoid using HTML when posting to the lists hosted on vger.kernel.org -- it's configured to ignore such mails AFAIK. Yeah forgot to set the plain text mode. Sorry for that >>> This patch addresses the issue with ATA_CMD_SMART pio mode >>> command for enumeration and device detection with ATA devices. >>> The X-Gene AHCI controller has an errata in which it cannot clear >>> the BSY bit after the PIO setup FIS. The dma state machine enters >> Hum, if this happens after every PIO command (PIO setup FISes are not >> specific to the command, right?), perhaps it would make more sense to record >> the *protocol* used by the last command? > No it happens for IDENTIFY DEVICE, ATA_CMD_PACKET and ATA_CMD_SMART commands . > It is actually the commands associated with a BSY bit clearing. I don't understand that -- BSY bit is cleared for *every* command, either at the end of it, or along with setting the DRQ bit for PIO data transfer. BSY bit is cleared after the end of these commands by the controller. So due to the bug it doesn't clear it. When the DMA commands is issued , it check for the BSY bit cleared or not and finds not cleared and results in CMFatalErrorUpdate and hangs. >>> CMFatalErrorUpdate state and locks up. It is the same issue as >>> in the commit 2a0bdff6b958d1b2523d2754b6cd5e__0ea4053016 (ahci-xgene: >>> fix the dma state machine lockup for the IDENTIFY DEVICE PIO mode >>> command). >> [...] >>> Signed-off-by: Suman Tripathi <stripathi at apm.com <mailto:stripathi@apm.com>> >>> Reported-by: Mark Langsdorf <mlangsdo@redhat.com >>> <mailto:mlangsdo@redhat.com>> >>> MBR, Sergei On Tue, Feb 3, 2015 at 1:14 AM, Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> wrote: > On 02/02/2015 10:37 PM, Suman Tripathi wrote: > > Ugh, please avoid using HTML when posting to the lists hosted on > vger.kernel.org -- it's configured to ignore such mails AFAIK. > >>>> This patch addresses the issue with ATA_CMD_SMART pio mode >>>> command for enumeration and device detection with ATA devices. >>>> The X-Gene AHCI controller has an errata in which it cannot clear >>>> the BSY bit after the PIO setup FIS. The dma state machine enters > > >>> Hum, if this happens after every PIO command (PIO setup FISes are not >>> specific to the command, right?), perhaps it would make more sense to >>> record >>> the *protocol* used by the last command? > > >> No it happens for IDENTIFY DEVICE, ATA_CMD_PACKET and ATA_CMD_SMART >> commands . >> It is actually the commands associated with a BSY bit clearing. > > > I don't understand that -- BSY bit is cleared for *every* command, either > at the end of it, or along with setting the DRQ bit for PIO data transfer. > >>>> CMFatalErrorUpdate state and locks up. It is the same issue as >>>> in the commit 2a0bdff6b958d1b2523d2754b6cd5e__0ea4053016 >>>> (ahci-xgene: >>>> fix the dma state machine lockup for the IDENTIFY DEVICE PIO mode >>>> command). > > >>> [...] > > >>>> Signed-off-by: Suman Tripathi <stripathi@apm.com >>>> <mailto:stripathi@apm.com>> >>>> Reported-by: Mark Langsdorf <mlangsdo@redhat.com >>>> <mailto:mlangsdo@redhat.com>> >>>> > > MBR, Sergei > -- Thanks, with regards, Suman Tripathi ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v3] ahci_xgene: Fix the dma state machine lockup for the ATA_CMD_SMART PIO mode command. 2015-02-02 19:48 ` Suman Tripathi @ 2015-02-03 16:12 ` Suman Tripathi 0 siblings, 0 replies; 5+ messages in thread From: Suman Tripathi @ 2015-02-03 16:12 UTC (permalink / raw) To: linux-arm-kernel Ugh, please avoid using HTML when posting to the lists hosted on vger.kernel.org -- it's configured to ignore such mails AFAIK. Yeah forgot to set the plain text mode. Sorry for that >>> This patch addresses the issue with ATA_CMD_SMART pio mode >>> command for enumeration and device detection with ATA devices. >>> The X-Gene AHCI controller has an errata in which it cannot clear >>> the BSY bit after the PIO setup FIS. The dma state machine enters >> Hum, if this happens after every PIO command (PIO setup FISes are not >> specific to the command, right?), perhaps it would make more sense to record >> the *protocol* used by the last command? > No it happens for IDENTIFY DEVICE, ATA_CMD_PACKET and ATA_CMD_SMART commands . > It is actually the commands associated with a BSY bit clearing. I don't understand that -- BSY bit is cleared for *every* command, either at the end of it, or along with setting the DRQ bit for PIO data transfer. BSY bit is cleared after the end of these commands by the controller. So due to the bug it doesn't clear it. When the DMA commands is issued , it check for the BSY bit cleared or not and finds not cleared and results in CMFatalErrorUpdate and hangs. Ping ?? Any problem with this last posted version Actually Mark from redhat reported this issue while using smartctl and we found that ATA_CMD_SMART also has BSY bit not clearing issue.. On Tue, Feb 3, 2015 at 1:18 AM, Suman Tripathi <stripathi@apm.com> wrote: > Ugh, please avoid using HTML when posting to the lists hosted on > vger.kernel.org -- it's configured to ignore such mails AFAIK. > Yeah forgot to set the plain text mode. Sorry for that > >>>> This patch addresses the issue with ATA_CMD_SMART pio mode >>>> command for enumeration and device detection with ATA devices. >>>> The X-Gene AHCI controller has an errata in which it cannot clear >>>> the BSY bit after the PIO setup FIS. The dma state machine enters > > >>> Hum, if this happens after every PIO command (PIO setup FISes are not >>> specific to the command, right?), perhaps it would make more sense to record >>> the *protocol* used by the last command? > > >> No it happens for IDENTIFY DEVICE, ATA_CMD_PACKET and ATA_CMD_SMART commands . >> It is actually the commands associated with a BSY bit clearing. > > > I don't understand that -- BSY bit is cleared for *every* command, > either at the end of it, or along with setting the DRQ bit for PIO > data transfer. > BSY bit is cleared after the end of these commands by the controller. > So due to the bug it doesn't clear it. When the DMA commands is issued > , it check for the BSY bit cleared or not and finds not cleared and > results in CMFatalErrorUpdate and hangs. > >>>> CMFatalErrorUpdate state and locks up. It is the same issue as >>>> in the commit 2a0bdff6b958d1b2523d2754b6cd5e__0ea4053016 (ahci-xgene: >>>> fix the dma state machine lockup for the IDENTIFY DEVICE PIO mode >>>> command). > > >>> [...] > > >>>> Signed-off-by: Suman Tripathi <stripathi at apm.com <mailto:stripathi@apm.com>> >>>> Reported-by: Mark Langsdorf <mlangsdo@redhat.com >>>> <mailto:mlangsdo@redhat.com>> >>>> > > MBR, Sergei > > On Tue, Feb 3, 2015 at 1:14 AM, Sergei Shtylyov > <sergei.shtylyov@cogentembedded.com> wrote: >> On 02/02/2015 10:37 PM, Suman Tripathi wrote: >> >> Ugh, please avoid using HTML when posting to the lists hosted on >> vger.kernel.org -- it's configured to ignore such mails AFAIK. >> >>>>> This patch addresses the issue with ATA_CMD_SMART pio mode >>>>> command for enumeration and device detection with ATA devices. >>>>> The X-Gene AHCI controller has an errata in which it cannot clear >>>>> the BSY bit after the PIO setup FIS. The dma state machine enters >> >> >>>> Hum, if this happens after every PIO command (PIO setup FISes are not >>>> specific to the command, right?), perhaps it would make more sense to >>>> record >>>> the *protocol* used by the last command? >> >> >>> No it happens for IDENTIFY DEVICE, ATA_CMD_PACKET and ATA_CMD_SMART >>> commands . >>> It is actually the commands associated with a BSY bit clearing. >> >> >> I don't understand that -- BSY bit is cleared for *every* command, either >> at the end of it, or along with setting the DRQ bit for PIO data transfer. >> >>>>> CMFatalErrorUpdate state and locks up. It is the same issue as >>>>> in the commit 2a0bdff6b958d1b2523d2754b6cd5e__0ea4053016 >>>>> (ahci-xgene: >>>>> fix the dma state machine lockup for the IDENTIFY DEVICE PIO mode >>>>> command). >> >> >>>> [...] >> >> >>>>> Signed-off-by: Suman Tripathi <stripathi@apm.com >>>>> <mailto:stripathi@apm.com>> >>>>> Reported-by: Mark Langsdorf <mlangsdo@redhat.com >>>>> <mailto:mlangsdo@redhat.com>> >>>>> >> >> MBR, Sergei >> > > > > -- > Thanks, > with regards, > Suman Tripathi -- Thanks, with regards, Suman Tripathi ^ permalink raw reply [flat|nested] 5+ messages in thread
* [PATCH v3] ahci_xgene: Fix the dma state machine lockup for the ATA_CMD_SMART PIO mode command. [not found] ` <1422900439-5541-2-git-send-email-stripathi@apm.com> 2015-02-02 19:12 ` [PATCH v3] ahci_xgene: Fix the dma state machine lockup for the ATA_CMD_SMART PIO mode command Sergei Shtylyov @ 2015-02-03 16:18 ` Tejun Heo 1 sibling, 0 replies; 5+ messages in thread From: Tejun Heo @ 2015-02-03 16:18 UTC (permalink / raw) To: linux-arm-kernel On Mon, Feb 02, 2015 at 11:37:19PM +0530, Suman Tripathi wrote: > This patch addresses the issue with ATA_CMD_SMART pio mode > command for enumeration and device detection with ATA devices. > The X-Gene AHCI controller has an errata in which it cannot clear > the BSY bit after the PIO setup FIS. The dma state machine enters > CMFatalErrorUpdate state and locks up. It is the same issue as > in the commit 2a0bdff6b958d1b2523d2754b6cd5e0ea4053016 (ahci-xgene: The right format is 2a0bdff6b958 ("ahci-xgene: fix the dma state machine lockup for the IDENTIFY DEVICE PIO mode command"). > fix the dma state machine lockup for the IDENTIFY DEVICE PIO mode > command). > > For example : without this patch it results in READ DMA command failure > as shown below : > > [ 126.700072] ata2.00: exception Emask 0x0 SAct 0x0 > SErr 0x0 action 0x6 frozen > [ 126.707089] ata2.00: failed command: READ DMA > [ 126.711426] ata2.00: cmd c8/00:08:00:55:57/00:00:00:00:00/e1 tag 1 > dma 4096 in > [ 126.711426] res 40/00:ff:00:00:00/00:00:00:00:00/40 Emask > 0x4 (timeout) > [ 126.725956] ata2.00: status: { DRDY } > > Signed-off-by: Suman Tripathi <stripathi@apm.com> > Reported-by: Mark Langsdorf <mlangsdo@redhat.com> Applied to libata/for-3.19-fixes. Thanks. -- tejun ^ permalink raw reply [flat|nested] 5+ messages in thread
end of thread, other threads:[~2015-02-03 16:18 UTC | newest]
Thread overview: 5+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
[not found] <1422900439-5541-1-git-send-email-stripathi@apm.com>
[not found] ` <1422900439-5541-2-git-send-email-stripathi@apm.com>
2015-02-02 19:12 ` [PATCH v3] ahci_xgene: Fix the dma state machine lockup for the ATA_CMD_SMART PIO mode command Sergei Shtylyov
[not found] ` <CAOHikRBMPbyS0q6814+Xkez7ToBwrC7Yzp4sy=NMmPDg-5wCBA@mail.gmail.com>
2015-02-02 19:44 ` Sergei Shtylyov
2015-02-02 19:48 ` Suman Tripathi
2015-02-03 16:12 ` Suman Tripathi
2015-02-03 16:18 ` Tejun Heo
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox; as well as URLs for NNTP newsgroup(s).