From: grygorii.strashko@linaro.org (Grygorii.Strashko@linaro.org)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH] gpio: omap: Fix regression for MPUIO interrupts
Date: Fri, 24 Apr 2015 17:58:29 +0300 [thread overview]
Message-ID: <553A5A15.1030605@linaro.org> (raw)
In-Reply-To: <1429833257-28188-1-git-send-email-tony@atomide.com>
On 04/24/2015 02:54 AM, Tony Lindgren wrote:
> At some point with all the GPIO clean-up we've broken the
> MPUIO interrupts. Those are just a little bit different from
> the GPIO interrupts, so we can fix it up just by setting
> different irqchip functions for it. And then we can just
> remove all old code trying to do the same.
Reviewed-by: Grygorii Strashko <grygorii.strashko@linaro.org>
>
> Cc: Aaro Koskinen <aaro.koskinen@iki.fi>
> Cc: Felipe Balbi <balbi@ti.com>
> Cc: Javier Martinez Canillas <javier@dowhile0.org>
> Cc: Grygorii Strashko <grygorii.strashko@linaro.org>
> Cc: Kevin Hilman <khilman@deeprootsystems.com>
> Cc: Nishanth Menon <nm@ti.com>
> Cc: Santosh Shilimkar <ssantosh@kernel.org>
> Signed-off-by: Tony Lindgren <tony@atomide.com>
> ---
> drivers/gpio/gpio-omap.c | 48 +++++++++---------------------------------------
> 1 file changed, 9 insertions(+), 39 deletions(-)
>
> diff --git a/drivers/gpio/gpio-omap.c b/drivers/gpio/gpio-omap.c
> index 6553361..b59c3ca 100644
> --- a/drivers/gpio/gpio-omap.c
> +++ b/drivers/gpio/gpio-omap.c
> @@ -1023,38 +1023,8 @@ static void omap_gpio_mod_init(struct gpio_bank *bank)
> dev_err(bank->dev, "Could not get gpio dbck\n");
> }
>
> -static void
> -omap_mpuio_alloc_gc(struct gpio_bank *bank, unsigned int irq_start,
> - unsigned int num)
> -{
> - struct irq_chip_generic *gc;
> - struct irq_chip_type *ct;
> -
> - gc = irq_alloc_generic_chip("MPUIO", 1, irq_start, bank->base,
> - handle_simple_irq);
> - if (!gc) {
> - dev_err(bank->dev, "Memory alloc failed for gc\n");
> - return;
> - }
> -
> - ct = gc->chip_types;
> -
> - /* NOTE: No ack required, reading IRQ status clears it. */
> - ct->chip.irq_mask = irq_gc_mask_set_bit;
> - ct->chip.irq_unmask = irq_gc_mask_clr_bit;
> - ct->chip.irq_set_type = omap_gpio_irq_type;
> -
> - if (bank->regs->wkup_en)
> - ct->chip.irq_set_wake = omap_gpio_wake_enable;
> -
> - ct->regs.mask = OMAP_MPUIO_GPIO_INT / bank->stride;
> - irq_setup_generic_chip(gc, IRQ_MSK(num), IRQ_GC_INIT_MASK_CACHE,
> - IRQ_NOREQUEST | IRQ_NOPROBE, 0);
> -}
> -
> static int omap_gpio_chip_init(struct gpio_bank *bank, struct irq_chip *irqc)
> {
> - int j;
> static int gpio;
> int irq_base = 0;
> int ret;
> @@ -1101,6 +1071,15 @@ static int omap_gpio_chip_init(struct gpio_bank *bank, struct irq_chip *irqc)
> }
> #endif
>
> + /* MPUIO is a bit different, reading IRQ status clears it */
> + if (bank->is_mpuio) {
> + irqc->irq_ack = dummy_irq_chip.irq_ack;
> + irqc->irq_mask = irq_gc_mask_set_bit;
> + irqc->irq_unmask = irq_gc_mask_clr_bit;
> + if (!bank->regs->wkup_en)
> + irqc->irq_set_wake = NULL;
> + }
> +
> ret = gpiochip_irqchip_add(&bank->chip, irqc,
> irq_base, omap_gpio_irq_handler,
> IRQ_TYPE_NONE);
> @@ -1114,15 +1093,6 @@ static int omap_gpio_chip_init(struct gpio_bank *bank, struct irq_chip *irqc)
> gpiochip_set_chained_irqchip(&bank->chip, irqc,
> bank->irq, omap_gpio_irq_handler);
>
> - for (j = 0; j < bank->width; j++) {
> - int irq = irq_find_mapping(bank->chip.irqdomain, j);
> - if (bank->is_mpuio) {
> - omap_mpuio_alloc_gc(bank, irq, bank->width);
> - irq_set_chip_and_handler(irq, NULL, NULL);
> - set_irq_flags(irq, 0);
> - }
> - }
> -
> return 0;
> }
>
>
--
regards,
-grygorii
next prev parent reply other threads:[~2015-04-24 14:58 UTC|newest]
Thread overview: 6+ messages / expand[flat|nested] mbox.gz Atom feed top
2015-04-23 23:54 [PATCH] gpio: omap: Fix regression for MPUIO interrupts Tony Lindgren
2015-04-24 14:58 ` Grygorii.Strashko@linaro.org [this message]
2015-04-24 15:29 ` santosh shilimkar
2015-04-24 16:10 ` Felipe Balbi
2015-05-06 13:21 ` Linus Walleij
2015-05-06 15:36 ` Tony Lindgren
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=553A5A15.1030605@linaro.org \
--to=grygorii.strashko@linaro.org \
--cc=linux-arm-kernel@lists.infradead.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).