* [PATCH v4] ARM: at91/dt: add support for kizbox2
@ 2015-05-04 15:59 Gaël PORTAY
2015-05-11 9:14 ` Nicolas Ferre
0 siblings, 1 reply; 3+ messages in thread
From: Gaël PORTAY @ 2015-05-04 15:59 UTC (permalink / raw)
To: linux-arm-kernel
Add DT file for Kizbox 2 board.
This board is based on Atmel's SAMA5D31 Cortex-A5 SoC.
Signed-off-by: Ga?l PORTAY <g.portay@overkiz.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
---
Changes since v1:
- drop ek boards from compatible machine
- drop useless pmc node
Changes since v2:
- update to v4.0
- fix alphabetical order between gpio_keys and pwm_leds
Changes since v3:
- update to v4.0.1
- update "Acked-by" list
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-kizbox2.dts | 217 +++++++++++++++++++++++++++++++++++++
2 files changed, 218 insertions(+)
create mode 100644 arch/arm/boot/dts/at91-kizbox2.dts
diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 21726fd..375f81aa 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -36,6 +36,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
at91sam9x25ek.dtb \
at91sam9x35ek.dtb
dtb-$(CONFIG_SOC_SAM_V7) += \
+ at91-kizbox2.dtb \
at91-sama5d3_xplained.dtb \
sama5d31ek.dtb \
sama5d33ek.dtb \
diff --git a/arch/arm/boot/dts/at91-kizbox2.dts b/arch/arm/boot/dts/at91-kizbox2.dts
new file mode 100644
index 0000000..a0f2003
--- /dev/null
+++ b/arch/arm/boot/dts/at91-kizbox2.dts
@@ -0,0 +1,217 @@
+/*
+ * at91-kizbox2.dts - Device Tree file for Overkiz Kizbox 2 board
+ *
+ * Copyright (C) 2014 Ga?l PORTAY <g.portay@overkiz.com>
+ *
+ * Licensed under GPLv2 or later.
+ */
+/dts-v1/;
+#include "sama5d31.dtsi"
+#include "sama5d3_emac.dtsi"
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Overkiz Kizbox 2";
+ compatible = "overkiz,kizbox2", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
+
+ chosen {
+ bootargs = "ubi.mtd=ubi";
+ linux,stdout-path = &dbgu;
+ };
+
+ memory {
+ reg = <0x20000000 0x10000000>;
+ };
+
+ clocks {
+ slow_xtal {
+ clock-frequency = <32768>;
+ };
+
+ main_xtal {
+ clock-frequency = <12000000>;
+ };
+ };
+
+ ahb {
+ apb {
+ i2c1: i2c at f0018000 {
+ status = "okay";
+
+ pmic: act8865 at 5b {
+ compatible = "active-semi,act8865";
+ reg = <0x5b>;
+ status = "okay";
+
+ regulators {
+ vcc_1v8_reg: DCDC_REG1 {
+ regulator-name = "VCC_1V8";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ };
+
+ vcc_1v2_reg: DCDC_REG2 {
+ regulator-name = "VCC_1V2";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ };
+
+ vcc_3v3_reg: DCDC_REG3 {
+ regulator-name = "VCC_3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vddfuse_reg: LDO_REG1 {
+ regulator-name = "FUSE_2V5";
+ regulator-min-microvolt = <2500000>;
+ regulator-max-microvolt = <2500000>;
+ };
+
+ vddana_reg: LDO_REG2 {
+ regulator-name = "VDDANA";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ vled_reg: LDO_REG3 {
+ regulator-name = "VLED";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ };
+
+ v3v8_rf_reg: LDO_REG4 {
+ regulator-name = "V3V8_RF";
+ regulator-min-microvolt = <3800000>;
+ regulator-max-microvolt = <3800000>;
+ regulator-always-on;
+ };
+ };
+ };
+ };
+
+ usart0: serial at f001c000 {
+ status = "okay";
+ };
+
+ usart1: serial at f0020000 {
+ status = "okay";
+ };
+
+ pwm0: pwm at f002c000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_pwm0_pwmh0_1
+ &pinctrl_pwm0_pwmh1_1
+ &pinctrl_pwm0_pwmh2_0>;
+ status = "okay";
+ };
+
+ adc0: adc at f8018000 {
+ atmel,adc-vref = <3333>;
+ status = "okay";
+ };
+
+ usart2: serial at f8020000 {
+ status = "okay";
+ };
+
+ macb1: ethernet at f802c000 {
+ phy-mode = "rmii";
+ status = "okay";
+ };
+
+ dbgu: serial at ffffee00 {
+ status = "okay";
+ };
+
+ watchdog at fffffe40 {
+ status = "okay";
+ };
+ };
+
+ usb1: ohci at 00600000 {
+ status = "okay";
+ };
+
+ usb2: ehci at 00700000 {
+ status = "okay";
+ };
+
+ nand0: nand at 60000000 {
+ nand-bus-width = <8>;
+ nand-ecc-mode = "hw";
+ atmel,has-pmecc;
+ atmel,pmecc-cap = <4>;
+ atmel,pmecc-sector-size = <512>;
+ nand-on-flash-bbt;
+ status = "okay";
+
+ bootstrap at 0 {
+ label = "bootstrap";
+ reg = <0x0 0x20000>;
+ };
+
+ ubi at 20000 {
+ label = "ubi";
+ reg = <0x20000 0x7fe0000>;
+ };
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ prog {
+ label = "PB_PROG";
+ gpios = <&pioE 27 GPIO_ACTIVE_LOW>;
+ linux,code = <0x102>;
+ gpio-key,wakeup;
+ };
+
+ reset {
+ label = "PB_RST";
+ gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
+ linux,code = <0x100>;
+ gpio-key,wakeup;
+ };
+
+ user {
+ label = "PB_USER";
+ gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
+ linux,code = <0x101>;
+ gpio-key,wakeup;
+ };
+ };
+
+ pwm_leds {
+ compatible = "pwm-leds";
+
+ blue {
+ label = "pwm:blue:user";
+ pwms = <&pwm0 2 10000000 0>;
+ max-brightness = <255>;
+ linux,default-trigger = "default-on";
+ };
+
+ green {
+ label = "pwm:green:user";
+ pwms = <&pwm0 1 10000000 0>;
+ max-brightness = <255>;
+ linux,default-trigger = "default-on";
+ };
+
+ red {
+ label = "pwm:red:user";
+ pwms = <&pwm0 0 10000000 0>;
+ max-brightness = <255>;
+ linux,default-trigger = "default-on";
+ };
+ };
+};
--
1.9.1
^ permalink raw reply related [flat|nested] 3+ messages in thread
* [PATCH v4] ARM: at91/dt: add support for kizbox2
2015-05-04 15:59 [PATCH v4] ARM: at91/dt: add support for kizbox2 Gaël PORTAY
@ 2015-05-11 9:14 ` Nicolas Ferre
2015-05-11 11:02 ` Gaël PORTAY
0 siblings, 1 reply; 3+ messages in thread
From: Nicolas Ferre @ 2015-05-11 9:14 UTC (permalink / raw)
To: linux-arm-kernel
Le 04/05/2015 17:59, Ga?l PORTAY a ?crit :
> Add DT file for Kizbox 2 board.
> This board is based on Atmel's SAMA5D31 Cortex-A5 SoC.
>
> Signed-off-by: Ga?l PORTAY <g.portay@overkiz.com>
> Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
(little fix applied: see below).
> ---
> Changes since v1:
> - drop ek boards from compatible machine
> - drop useless pmc node
>
> Changes since v2:
> - update to v4.0
> - fix alphabetical order between gpio_keys and pwm_leds
>
> Changes since v3:
> - update to v4.0.1
> - update "Acked-by" list
>
> arch/arm/boot/dts/Makefile | 1 +
> arch/arm/boot/dts/at91-kizbox2.dts | 217 +++++++++++++++++++++++++++++++++++++
> 2 files changed, 218 insertions(+)
> create mode 100644 arch/arm/boot/dts/at91-kizbox2.dts
>
> diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> index 21726fd..375f81aa 100644
> --- a/arch/arm/boot/dts/Makefile
> +++ b/arch/arm/boot/dts/Makefile
> @@ -36,6 +36,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
> at91sam9x25ek.dtb \
> at91sam9x35ek.dtb
> dtb-$(CONFIG_SOC_SAM_V7) += \
> + at91-kizbox2.dtb \
> at91-sama5d3_xplained.dtb \
> sama5d31ek.dtb \
> sama5d33ek.dtb \
> diff --git a/arch/arm/boot/dts/at91-kizbox2.dts b/arch/arm/boot/dts/at91-kizbox2.dts
> new file mode 100644
> index 0000000..a0f2003
> --- /dev/null
> +++ b/arch/arm/boot/dts/at91-kizbox2.dts
> @@ -0,0 +1,217 @@
> +/*
> + * at91-kizbox2.dts - Device Tree file for Overkiz Kizbox 2 board
> + *
> + * Copyright (C) 2014 Ga?l PORTAY <g.portay@overkiz.com>
> + *
> + * Licensed under GPLv2 or later.
> + */
> +/dts-v1/;
> +#include "sama5d31.dtsi"
> +#include "sama5d3_emac.dtsi"
Not needed: it is already included in sama5d31.dtsi: I remove it before
applying the patch.
> +#include <dt-bindings/pwm/pwm.h>
> +
> +/ {
> + model = "Overkiz Kizbox 2";
> + compatible = "overkiz,kizbox2", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
> +
> + chosen {
> + bootargs = "ubi.mtd=ubi";
> + linux,stdout-path = &dbgu;
> + };
> +
> + memory {
> + reg = <0x20000000 0x10000000>;
> + };
> +
> + clocks {
> + slow_xtal {
> + clock-frequency = <32768>;
> + };
> +
> + main_xtal {
> + clock-frequency = <12000000>;
> + };
> + };
> +
> + ahb {
> + apb {
> + i2c1: i2c at f0018000 {
> + status = "okay";
> +
> + pmic: act8865 at 5b {
> + compatible = "active-semi,act8865";
> + reg = <0x5b>;
> + status = "okay";
> +
> + regulators {
> + vcc_1v8_reg: DCDC_REG1 {
> + regulator-name = "VCC_1V8";
> + regulator-min-microvolt = <1800000>;
> + regulator-max-microvolt = <1800000>;
> + regulator-always-on;
> + };
> +
> + vcc_1v2_reg: DCDC_REG2 {
> + regulator-name = "VCC_1V2";
> + regulator-min-microvolt = <1200000>;
> + regulator-max-microvolt = <1200000>;
> + regulator-always-on;
> + };
> +
> + vcc_3v3_reg: DCDC_REG3 {
> + regulator-name = "VCC_3V3";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vddfuse_reg: LDO_REG1 {
> + regulator-name = "FUSE_2V5";
> + regulator-min-microvolt = <2500000>;
> + regulator-max-microvolt = <2500000>;
> + };
> +
> + vddana_reg: LDO_REG2 {
> + regulator-name = "VDDANA";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + vled_reg: LDO_REG3 {
> + regulator-name = "VLED";
> + regulator-min-microvolt = <3300000>;
> + regulator-max-microvolt = <3300000>;
> + regulator-always-on;
> + };
> +
> + v3v8_rf_reg: LDO_REG4 {
> + regulator-name = "V3V8_RF";
> + regulator-min-microvolt = <3800000>;
> + regulator-max-microvolt = <3800000>;
> + regulator-always-on;
> + };
> + };
> + };
> + };
> +
> + usart0: serial at f001c000 {
> + status = "okay";
> + };
> +
> + usart1: serial at f0020000 {
> + status = "okay";
> + };
> +
> + pwm0: pwm at f002c000 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_pwm0_pwmh0_1
> + &pinctrl_pwm0_pwmh1_1
> + &pinctrl_pwm0_pwmh2_0>;
> + status = "okay";
> + };
> +
> + adc0: adc at f8018000 {
> + atmel,adc-vref = <3333>;
> + status = "okay";
> + };
> +
> + usart2: serial at f8020000 {
> + status = "okay";
> + };
> +
> + macb1: ethernet at f802c000 {
> + phy-mode = "rmii";
> + status = "okay";
> + };
> +
> + dbgu: serial at ffffee00 {
> + status = "okay";
> + };
> +
> + watchdog at fffffe40 {
> + status = "okay";
> + };
> + };
> +
> + usb1: ohci at 00600000 {
> + status = "okay";
> + };
> +
> + usb2: ehci at 00700000 {
> + status = "okay";
> + };
> +
> + nand0: nand at 60000000 {
> + nand-bus-width = <8>;
> + nand-ecc-mode = "hw";
> + atmel,has-pmecc;
> + atmel,pmecc-cap = <4>;
> + atmel,pmecc-sector-size = <512>;
> + nand-on-flash-bbt;
> + status = "okay";
> +
> + bootstrap at 0 {
> + label = "bootstrap";
> + reg = <0x0 0x20000>;
> + };
> +
> + ubi at 20000 {
> + label = "ubi";
> + reg = <0x20000 0x7fe0000>;
> + };
> + };
> + };
> +
> + gpio_keys {
> + compatible = "gpio-keys";
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + prog {
> + label = "PB_PROG";
> + gpios = <&pioE 27 GPIO_ACTIVE_LOW>;
> + linux,code = <0x102>;
> + gpio-key,wakeup;
> + };
> +
> + reset {
> + label = "PB_RST";
> + gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
> + linux,code = <0x100>;
> + gpio-key,wakeup;
> + };
> +
> + user {
> + label = "PB_USER";
> + gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
> + linux,code = <0x101>;
> + gpio-key,wakeup;
> + };
> + };
> +
> + pwm_leds {
> + compatible = "pwm-leds";
> +
> + blue {
> + label = "pwm:blue:user";
> + pwms = <&pwm0 2 10000000 0>;
> + max-brightness = <255>;
> + linux,default-trigger = "default-on";
> + };
> +
> + green {
> + label = "pwm:green:user";
> + pwms = <&pwm0 1 10000000 0>;
> + max-brightness = <255>;
> + linux,default-trigger = "default-on";
> + };
> +
> + red {
> + label = "pwm:red:user";
> + pwms = <&pwm0 0 10000000 0>;
> + max-brightness = <255>;
> + linux,default-trigger = "default-on";
> + };
> + };
> +};
>
--
Nicolas Ferre
^ permalink raw reply [flat|nested] 3+ messages in thread
* [PATCH v4] ARM: at91/dt: add support for kizbox2
2015-05-11 9:14 ` Nicolas Ferre
@ 2015-05-11 11:02 ` Gaël PORTAY
0 siblings, 0 replies; 3+ messages in thread
From: Gaël PORTAY @ 2015-05-11 11:02 UTC (permalink / raw)
To: linux-arm-kernel
Thanks
Sent from my Cyanogen phone
On May 11, 2015 11:14 AM, Nicolas Ferre <nicolas.ferre@atmel.com> wrote:
>
> Le 04/05/2015 17:59, Ga?l PORTAY a ?crit :
> > Add DT file for Kizbox 2 board.
> > This board is based on Atmel's SAMA5D31 Cortex-A5 SoC.
> >
> > Signed-off-by: Ga?l PORTAY <g.portay@overkiz.com>
> > Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
> > Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
>
> Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
>
> (little fix applied: see below).
>
> > ---
> > Changes since v1:
> > - drop ek boards from compatible machine
> > - drop useless pmc node
> >
> > Changes since v2:
> > - update to v4.0
> > - fix alphabetical order between gpio_keys and pwm_leds
> >
> > Changes since v3:
> > - update to v4.0.1
> > - update "Acked-by" list
> >
> >? arch/arm/boot/dts/Makefile???????? |?? 1 +
> >? arch/arm/boot/dts/at91-kizbox2.dts | 217 +++++++++++++++++++++++++++++++++++++
> >? 2 files changed, 218 insertions(+)
> >? create mode 100644 arch/arm/boot/dts/at91-kizbox2.dts
> >
> > diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
> > index 21726fd..375f81aa 100644
> > --- a/arch/arm/boot/dts/Makefile
> > +++ b/arch/arm/boot/dts/Makefile
> > @@ -36,6 +36,7 @@ dtb-$(CONFIG_SOC_SAM_V4_V5) += \
> >? at91sam9x25ek.dtb \
> >? at91sam9x35ek.dtb
> >? dtb-$(CONFIG_SOC_SAM_V7) += \
> > + at91-kizbox2.dtb \
> >? at91-sama5d3_xplained.dtb \
> >? sama5d31ek.dtb \
> >? sama5d33ek.dtb \
> > diff --git a/arch/arm/boot/dts/at91-kizbox2.dts b/arch/arm/boot/dts/at91-kizbox2.dts
> > new file mode 100644
> > index 0000000..a0f2003
> > --- /dev/null
> > +++ b/arch/arm/boot/dts/at91-kizbox2.dts
> > @@ -0,0 +1,217 @@
> > +/*
> > + * at91-kizbox2.dts - Device Tree file for Overkiz Kizbox 2 board
> > + *
> > + * Copyright (C) 2014 Ga?l PORTAY <g.portay@overkiz.com>
> > + *
> > + * Licensed under GPLv2 or later.
> > + */
> > +/dts-v1/;
> > +#include "sama5d31.dtsi"
> > +#include "sama5d3_emac.dtsi"
>
> Not needed: it is already included in sama5d31.dtsi: I remove it before
> applying the patch.
>
> > +#include <dt-bindings/pwm/pwm.h>
> > +
> > +/ {
> > + model = "Overkiz Kizbox 2";
> > + compatible = "overkiz,kizbox2", "atmel,sama5d31", "atmel,sama5d3", "atmel,sama5";
> > +
> > + chosen {
> > + bootargs = "ubi.mtd=ubi";
> > + linux,stdout-path = &dbgu;
> > + };
> > +
> > + memory {
> > + reg = <0x20000000 0x10000000>;
> > + };
> > +
> > + clocks {
> > + slow_xtal {
> > + clock-frequency = <32768>;
> > + };
> > +
> > + main_xtal {
> > + clock-frequency = <12000000>;
> > + };
> > + };
> > +
> > + ahb {
> > + apb {
> > + i2c1: i2c at f0018000 {
> > + status = "okay";
> > +
> > + pmic: act8865 at 5b {
> > + compatible = "active-semi,act8865";
> > + reg = <0x5b>;
> > + status = "okay";
> > +
> > + regulators {
> > + vcc_1v8_reg: DCDC_REG1 {
> > + regulator-name = "VCC_1V8";
> > + regulator-min-microvolt = <1800000>;
> > + regulator-max-microvolt = <1800000>;
> > + regulator-always-on;
> > + };
> > +
> > + vcc_1v2_reg: DCDC_REG2 {
> > + regulator-name = "VCC_1V2";
> > + regulator-min-microvolt = <1200000>;
> > + regulator-max-microvolt = <1200000>;
> > + regulator-always-on;
> > + };
> > +
> > + vcc_3v3_reg: DCDC_REG3 {
> > + regulator-name = "VCC_3V3";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vddfuse_reg: LDO_REG1 {
> > + regulator-name = "FUSE_2V5";
> > + regulator-min-microvolt = <2500000>;
> > + regulator-max-microvolt = <2500000>;
> > + };
> > +
> > + vddana_reg: LDO_REG2 {
> > + regulator-name = "VDDANA";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + vled_reg: LDO_REG3 {
> > + regulator-name = "VLED";
> > + regulator-min-microvolt = <3300000>;
> > + regulator-max-microvolt = <3300000>;
> > + regulator-always-on;
> > + };
> > +
> > + v3v8_rf_reg: LDO_REG4 {
> > + regulator-name = "V3V8_RF";
> > + regulator-min-microvolt = <3800000>;
> > + regulator-max-microvolt = <3800000>;
> > + regulator-always-on;
> > + };
> > + };
> > + };
> > + };
> > +
> > + usart0: serial at f001c000 {
> > + status = "okay";
> > + };
> > +
> > + usart1: serial at f0020000 {
> > + status = "okay";
> > + };
> > +
> > + pwm0: pwm at f002c000 {
> > + pinctrl-names = "default";
> > + pinctrl-0 = <&pinctrl_pwm0_pwmh0_1
> > + ???? &pinctrl_pwm0_pwmh1_1
> > + ???? &pinctrl_pwm0_pwmh2_0>;
> > + status = "okay";
> > + };
> > +
> > + adc0: adc at f8018000 {
> > + atmel,adc-vref = <3333>;
> > + status = "okay";
> > + };
> > +
> > + usart2: serial at f8020000 {
> > + status = "okay";
> > + };
> > +
> > + macb1: ethernet at f802c000 {
> > + phy-mode = "rmii";
> > + status = "okay";
> > + };
> > +
> > + dbgu: serial at ffffee00 {
> > + status = "okay";
> > + };
> > +
> > + watchdog at fffffe40 {
> > + status = "okay";
> > + };
> > + };
> > +
> > + usb1: ohci at 00600000 {
> > + status = "okay";
> > + };
> > +
> > + usb2: ehci at 00700000 {
> > + status = "okay";
> > + };
> > +
> > + nand0: nand at 60000000 {
> > + nand-bus-width = <8>;
> > + nand-ecc-mode = "hw";
> > + atmel,has-pmecc;
> > + atmel,pmecc-cap = <4>;
> > + atmel,pmecc-sector-size = <512>;
> > + nand-on-flash-bbt;
> > + status = "okay";
> > +
> > + bootstrap at 0 {
> > + label = "bootstrap";
> > + reg = <0x0 0x20000>;
> > + };
> > +
> > + ubi at 20000 {
> > + label = "ubi";
> > + reg = <0x20000 0x7fe0000>;
> > + };
> > + };
> > + };
> > +
> > + gpio_keys {
> > + compatible = "gpio-keys";
> > + #address-cells = <1>;
> > + #size-cells = <0>;
> > +
> > + prog {
> > + label = "PB_PROG";
> > + gpios = <&pioE 27 GPIO_ACTIVE_LOW>;
> > + linux,code = <0x102>;
> > + gpio-key,wakeup;
> > + };
> > +
> > + reset {
> > + label = "PB_RST";
> > + gpios = <&pioE 29 GPIO_ACTIVE_LOW>;
> > + linux,code = <0x100>;
> > + gpio-key,wakeup;
> > + };
> > +
> > + user {
> > + label = "PB_USER";
> > + gpios = <&pioE 31 GPIO_ACTIVE_HIGH>;
> > + linux,code = <0x101>;
> > + gpio-key,wakeup;
> > + };
> > + };
> > +
> > + pwm_leds {
> > + compatible = "pwm-leds";
> > +
> > + blue {
> > + label = "pwm:blue:user";
> > + pwms = <&pwm0 2 10000000 0>;
> > + max-brightness = <255>;
> > + linux,default-trigger = "default-on";
> > + };
> > +
> > + green {
> > + label = "pwm:green:user";
> > + pwms = <&pwm0 1 10000000 0>;
> > + max-brightness = <255>;
> > + linux,default-trigger = "default-on";
> > + };
> > +
> > + red {
> > + label = "pwm:red:user";
> > + pwms = <&pwm0 0 10000000 0>;
> > + max-brightness = <255>;
> > + linux,default-trigger = "default-on";
> > + };
> > + };
> > +};
> >
>
>
> --
> Nicolas Ferre
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2015-05-11 11:02 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz follow: Atom feed
-- links below jump to the message on this page --
2015-05-04 15:59 [PATCH v4] ARM: at91/dt: add support for kizbox2 Gaël PORTAY
2015-05-11 9:14 ` Nicolas Ferre
2015-05-11 11:02 ` Gaël PORTAY
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).