linux-arm-kernel.lists.infradead.org archive mirror
 help / color / mirror / Atom feed
From: ezequiel@vanguardiasur.com.ar (Ezequiel Garcia)
To: linux-arm-kernel@lists.infradead.org
Subject: [PATCH v5 07/12] mtd: nand: add Samsung K9GBG08U0A-M to nand_ids table
Date: Sun, 24 May 2015 15:42:11 -0300	[thread overview]
Message-ID: <55621B83.4040909@vanguardiasur.com.ar> (raw)
In-Reply-To: <20150520144341.GQ22054@kwain>

Antoine,

On 05/20/2015 11:43 AM, Antoine Tenart wrote:
[..]
>>
>> I just had a look on the datasheet, and I you're right, the nand should
>> support JDEC. However I get a "No NAND device found" error when
>> reverting this patch.
>>
>> It seems nand_flash_detect_jedec() is not reading "JDEC" and is returning
>> directly. I'm having a look at this.
> 
> So, I can read 'J', 'E', 'D' and 'E' but then I got 0xff's. So I tried
> to only check of JEDE in nand_flash_detect_jedec() but the JEDEC
> parameter page was then not valid.
> 

This uncovers two different bugs in the driver.

1. read_id_bytes is either '2' or '4', but JEDEC detections needs at
least 5 bytes.

2. The initial buffer (to read the ID and the parameter page) has
256 bytes, but the JEDEC parameter page is 512-bytes.

And while at it, the driver doesn't seem to support reading the
redundant parameter pages (recently reported on barebox ML [1]). So this
is a third bug.

Would you try setting read_id_bytes to '5' and also increasing the READ_PARAM
transfer length? Something like this:

diff --git a/drivers/mtd/nand/pxa3xx_nand.c b/drivers/mtd/nand/pxa3xx_nand.c
index 1259cc5..851372f 100644
--- a/drivers/mtd/nand/pxa3xx_nand.c
+++ b/drivers/mtd/nand/pxa3xx_nand.c
@@ -48,7 +48,7 @@
  * STATUS, READID and PARAM. The largest of these is the PARAM command,
  * needing 256 bytes.
  */
-#define INIT_BUFFER_SIZE	256
+#define INIT_BUFFER_SIZE	2048
 
 /* registers and bit definitions */
 #define NDCR		(0x00) /* Control register */
@@ -899,18 +899,18 @@ static int prepare_set_command(struct pxa3xx_nand_info *info, int command,
 		break;
 
 	case NAND_CMD_PARAM:
-		info->buf_count = 256;
+		info->buf_count = 2048;
 		info->ndcb0 |= NDCB0_CMD_TYPE(0)
 				| NDCB0_ADDR_CYC(1)
 				| NDCB0_LEN_OVRD
 				| command;
 		info->ndcb1 = (column & 0xFF);
-		info->ndcb3 = 256;
-		info->data_size = 256;
+		info->ndcb3 = 2048;
+		info->data_size = 2048;
 		break;

[1] http://lists.infradead.org/pipermail/barebox/2015-May/023515.html

Thanks,
-- 
Ezequiel Garcia, VanguardiaSur
www.vanguardiasur.com.ar

  reply	other threads:[~2015-05-24 18:42 UTC|newest]

Thread overview: 32+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2015-05-11 14:58 [PATCH v5 00/12] ARM: berlin: add nand support Antoine Tenart
2015-05-11 14:58 ` [PATCH v5 01/12] mtd: pxa3xx_nand: add a non mandatory ECC clock Antoine Tenart
2015-05-11 14:58 ` [PATCH v5 02/12] Documentation: bindings: document the clocks for pxa3xx-nand Antoine Tenart
2015-05-11 14:58 ` [PATCH v5 03/12] mtd: pxa3xx_nand: add a default chunk size Antoine Tenart
2015-05-11 14:58 ` [PATCH v5 04/12] mtd: pxa3xx_nand: add helpers to setup the timings Antoine Tenart
2015-05-11 14:58 ` [PATCH v5 05/12] mtd: pxa3xx_nand: rework flash detection and timing setup Antoine Tenart
2015-05-11 22:10   ` Ezequiel Garcia
2015-05-12 14:39     ` Antoine Tenart
2015-05-16 21:23       ` Ezequiel Garcia
2015-05-20 13:55         ` Antoine Tenart
2015-05-20 13:56           ` Ezequiel Garcia
2015-05-20 14:04             ` Antoine Tenart
2015-05-16 22:02   ` Ezequiel Garcia
2015-05-20 14:03     ` Antoine Tenart
2015-05-20 14:05       ` Ezequiel Garcia
2015-05-11 14:58 ` [PATCH v5 06/12] mtd: pxa3xx_nand: clean up the pxa3xx timings Antoine Tenart
2015-05-11 14:58 ` [PATCH v5 07/12] mtd: nand: add Samsung K9GBG08U0A-M to nand_ids table Antoine Tenart
2015-05-16 18:57   ` Ezequiel Garcia
2015-05-20 14:06     ` Antoine Tenart
2015-05-20 14:09       ` Ezequiel Garcia
2015-05-20 14:24         ` Antoine Tenart
2015-05-20 14:43           ` Antoine Tenart
2015-05-24 18:42             ` Ezequiel Garcia [this message]
2015-07-20 18:08               ` Brian Norris
2015-07-20 18:22                 ` Ezequiel Garcia
2015-05-11 14:58 ` [PATCH v5 08/12] mtd: pxa3xx_nand: add support for the Marvell Berlin nand controller Antoine Tenart
2015-05-11 14:58 ` [PATCH v5 09/12] Documentation: bindings: add the Berlin nand controller compatible Antoine Tenart
2015-05-11 14:58 ` [PATCH v5 10/12] mtd: nand: let Marvell Berlin SoCs select the pxa3xx driver Antoine Tenart
2015-05-11 14:59 ` [PATCH v5 11/12] ARM: berlin: add BG2Q node for the nand Antoine Tenart
2015-05-11 14:59 ` [PATCH v5 12/12] ARM: berlin: enable flash on the BG2Q DMP Antoine Tenart
2015-05-16 21:37 ` [PATCH v5 00/12] ARM: berlin: add nand support Ezequiel Garcia
2015-05-20 14:08   ` Antoine Tenart

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=55621B83.4040909@vanguardiasur.com.ar \
    --to=ezequiel@vanguardiasur.com.ar \
    --cc=linux-arm-kernel@lists.infradead.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox;
as well as URLs for NNTP newsgroup(s).